qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h
qlcnic: min_mtu 68, max_mtu 9600
CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
mvneta_change_mtu for simplicity
mvpp2: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
mvpp2_change_mtu for simplicity
pxa168_eth: min_mtu 68, max_mtu 9500
skge: min_mtu 60, max_mtu 9000
sky2: min_mtu 68, max_mtu 1500 or 9000, depending on hw
CC: netdev@vger.kernel.org
CC: Mirko Lindner <mlindner@marvell.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: min_mtu 60, max_mtu 9000/1500
bnxt: min_mtu 60, max_mtu 9000
bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
duplicated defines from bnx2x_link.c.
bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.
bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
bcm_enet_change_mtu.
b44: min_mtu 60, max_mtu 1500
CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atl2: min_mtu 40, max_mtu 1504
- Remove a few redundant defines that already have equivalents in
if_ether.h.
atl1: min_mtu 42, max_mtu 10218
atl1e: min_mtu 42, max_mtu 8170
atl1c: min_mtu 42, max_mtu 6122/1500
- GbE hardware gets a max_mtu of 6122, slower hardware gets 1500.
alx: min_mtu 34, max_mtu 9256
- Not so sure that minimum MTU number is really what was intended, but
that's what the math actually makes it out to be, due to max_frame
manipulations and comparison in alx_change_mtu, rather than just
comparing new_mtu. (I think 68 was the intended min_mtu value).
CC: netdev@vger.kernel.org
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N says:
====================
add support for impedance control for TI dp83867 phy and fix 2nd ethernet on dra72 rev C evm
Add support for configurable impedance control for TI dp83867
phy via devicetree. More documentation in [1].
CPSW second ethernet is not working, fix it by enabling
impedance configuration on the phy.
Verified the patch on DRA72 Rev C evm, logs at [2]. Also pushed
a branch [3] for others to test.
Changes from v3:
* Fixup change log text and no code changes.
Changes from v2:
* Fixed a typo in dts and driver.
Changes from initial version:
* As per Sekhar's comment, instead of passing impedance values,
change to max and min impedance from DT
* Adopted phy_read_mmd_indirect() to cunnrent implementation.
* Corrected the phy delay timings to the optimal value.
[1] - http://www.ti.com/lit/ds/symlink/dp83867ir.pdf
[2] - http://pastebin.ubuntu.com/23343139/
[3] - git://git.ti.com/~mugunthanvnm/ti-linux-kernel/linux.git dp83867-v4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current delay settings of the phy are not the optimal value,
fix it with correct values.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default impedance settings of the phy is not the optimal
value, due to this the second ethernet is not working. Fix it
with correct values which makes the second ethernet port to work.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for programmable MAC impedance configuration
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documention of ti,min-output-impedance and ti,max-output-impedance
which can be used to correct MAC impedance mismatch using phy extended
registers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
args.u.name_type is of type unsigned int and is always >= 0.
This fixes the following GCC warning:
net/8021q/vlan.c: In function ‘vlan_ioctl_handler’:
net/8021q/vlan.c:574:14: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check is for max_mtu but message reports min_mtu.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENODEV from the of_phy_connect() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phys_addr_t may be wider than a pointer and has to be printed
using the special %pap format string, as pointed out by
this new warning.
arch/x86/include/../../../drivers/net/fjes/fjes_trace.h: In function ‘trace_raw_output_fjes_hw_start_debug_req’:
arch/x86/include/../../../drivers/net/fjes/fjes_trace.h:212:563: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
Note that this has to pass the address by reference instead of
casting it to a different type.
Fixes: b6ba737d0b ("fjes: ethtool -w and -W support for fjes driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Interrupt support for mv88e6xxx
This patchset add interrupt controller support to the MV88E6xxx. This
allows access to the interrupts the internal PHY generate. These
interrupts can then be associated to a PHY device in the device tree
and used by the PHY lib, rather than polling.
Since interrupt handling needs to make MDIO bus accesses, threaded
interrupts are used. The phylib needs to request the PHY interrupt
using the threaded IRQ API. This in term allows some simplification to
the code, in that the phylib interrupt handler can directly call
phy_change(), rather than use a work queue. The work queue is however
retained for the phy_mac_interrupt() call, which can be called in hard
interrupt context.
Since RFC v1:
Keep phy_mac_interrupt() callable in hard IRQ context.
The fix to trigger the phy state machine transitions on interrupts has
already been submitted, so is dropped from here.
Added back shared interrupts support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the fixed name "phy_interrupt" is not very informative in
/proc/interrupts when there are a lot of phys, e.g. a device with an
Ethernet switch. So when requesting the interrupt, use the name of the
phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt lines from PHYs maybe connected to I2C bus expanders, or
from switches on MDIO busses. Such interrupts are sourced from devices
which sleep, so use threaded interrupts. Threaded interrupts require
that the interrupt requester also uses the threaded API. Change the
phylib to use the threaded API, which is backwards compatible with
none-threaded IRQs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
rds_conn_path_error already prefixes "RDS:" to the output.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This macro's last use was removed in commit d769ef81d5
("RDS: Update rds_conn_shutdown to work with rds_conn_path")
so make the macro and the __rds_conn_error function definition
and declaration disappear.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the gateway is set on an ILA route we don't need to bother with using
the destination cache in the ILA route. Translation does not change the
routing in this case so we can stick with orig_output in the lwstate
output function.
Tested: Ran netperf with and without gateway for LWT route.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This l3mdev_ops structure is only stored in the l3mdev_ops field of a
net_device structure. This field is declared const, so the l3mdev_ops
structure can be declared as const also. Additionally drop the
__read_mostly annotation.
The semantic patch that adds const is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct l3mdev_ops i@p = { ... };
@ok@
identifier r.i;
struct net_device *e;
position p;
@@
e->l3mdev_ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct l3mdev_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct l3mdev_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output
of the size command, first before then after the transformation:
text data bss dec hex filename
7364 466 52 7882 1eca drivers/net/ipvlan/ipvlan_main.o
7412 434 52 7898 1eda drivers/net/ipvlan/ipvlan_main.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
ila: Cache a route in ILA lwt structure
Add a dst_cache to ila_lwt structure. This holds a cached route for the
translated address. In ila_output we now perform a route lookup after
translation and if possible (destination in original route is full 128
bits) we set the dst_cache. Subsequent calls to ila_output can then use
the cache to avoid the route lookup.
This eliminates the need to set the gateway on ILA routes as previously
was being done. Now we can do somthing like:
./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \
csum-mode neutral-map dev eth0 ## No via needed!
Also, add destroy_state to lwt ops. We need this do destroy the
dst_cache.
- v2
- Fixed comparisons to fc_dst_len to make comparison against number
of bits in data structure not bytes.
- Move destroy_state under build_state (requested by Jiri)
- Other minor cleanup
Tested:
Running 200 TCP_RR streams:
Baseline, no ILA
1730716 tps
102/170/313 50/90/99% latencies
88.11 CPU utilization
Using ILA in both directions
1680428 tps
105/176/325 50/90/99% latencies
88.16 CPU utilization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dst_cache to ila_lwt structure. This holds a cached route for the
translated address. In ila_output we now perform a route lookup after
translation and if possible (destination in original route is full 128
bits) we set the dst_cache. Subsequent calls to ila_output can then use
the cache to avoid the route lookup.
This eliminates the need to set the gateway on ILA routes as previously
was being done. Now we can do something like:
./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \
csum-mode neutral-map dev eth0 ## No via needed!
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users of lwt tunnels may set up some secondary state in build_state
function. Add a corresponding destroy_state function to allow users to
clean up state. This destroy state function is called from lwstate_free.
Also, we now free lwstate using kfree_rcu so user can assume structure
is not freed before rcu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taku Izumi says:
====================
FUJITSU Extended Socket driver version 1.2
This patchset updates FUJITSU Extended Socket network driver into version 1.2.
This includes the following enhancements:
- ethtool -d support
- ethtool -S enhancement
- ethtool -w/-W support
- Add some debugging feature (tracepoints etc)
v1 -> v2:
- Use u64 instead of phys_addr_t as TP_STRUCT__entry
- Use ethtool facility to achieve debug mode instead of using debugfs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds debugfs entry to show EP status information.
You can get each EP's status information like the following:
# cat /sys/kernel/debug/fjes/fjes.0/status
EPID STATUS SAME_ZONE CONNECTED
ep0 shared Y Y
ep1 - - -
ep2 unshared N N
ep3 unshared N N
ep4 unshared N N
ep5 unshared N N
ep6 unshared N N
ep7 unshared N N
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds implementation of supporting
ethtool -w and -W for fjes driver.
You can enable and disable firmware debug mode by
using ethtool -W, and also retrieve firmware
activity information by using ethtool -w.
This is useful for debugging.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds tracepoints in fjes driver.
This is useful for debugging purpose.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances ethtool -S for fjes driver so that
EP related statistics can be retrieved.
The following statistics can be displayed via ethtool -S:
ep%d_com_regist_buf_exec
ep%d_com_unregist_buf_exec
ep%d_send_intr_rx
ep%d_send_intr_unshare
ep%d_send_intr_zoneupdate
ep%d_recv_intr_rx
ep%d_recv_intr_unshare
ep%d_recv_intr_stop
ep%d_recv_intr_zoneupdate
ep%d_tx_buffer_full
ep%d_tx_dropped_not_shared
ep%d_tx_dropped_ver_mismatch
ep%d_tx_dropped_buf_size_mismatch
ep%d_tx_dropped_vlanid_mismatch
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
qed*: driver updates
There are several new additions in this series;
Most are connected to either Tx offloading or Rx classifications
[either fastpath changes or supporting configuration].
In addition, there's a single IOV enhancement.
Please consider applying this series to `net-next'.
V2->V3:
Fixes below kbuild warning
call to '__compiletime_assert_60' declared with
attribute error: Need native word sized stores/loads for atomicity.
V1->V2:
Added a fix for the race in ramrod handling
pointed by Eric Dumazet [patch 7].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While handling SPQ ramrod completion, there is a possible race
where driver might not read updated fw return code based on
ramrod completion done. This patch ensures that fw return code
is written first and then completion done flag is updated
using appropriate memory barriers.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Malicious VFs might be caught in several different methods:
- Misusing their bar permission and being blocked by hardware.
- Misusing their fastpath logic and being blocked by firmware.
- Misusing their interaction with their PF via hw-channel,
and being blocked by PF driver.
On the first two items, firmware would indicate to driver that
the VF is to be considered malicious, but would sometime still
allow the VF to communicate with the PF [depending on the exact
nature of the malicious activity done by the VF].
The current existing logic on the PF side lacks handling of such events,
and might allow the PF to perform some incorrect configuration on behalf
of a VF that was previously indicated as malicious.
The new scheme is simple -
Once the PF determines a VF is malicious it would:
a. Ignore any further requests on behalf of the VF-driver.
b. Prevent any configurations initiated by the hyperuser for
the malicious VF, as firmware isn't willing to serve such.
The malicious indication would be cleared upon the VF flr,
after which it would become usable once again.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a ramrod is being sent for some device configuration,
the driver is going to sleep at least 5ms between each iteration
of polling on the completion of the ramrod.
However, in almost every configuration scenario the firmware
would be able to comply and complete the ramrod in a manner of
several usecs. This is especially important in cases where there
might be a lot of sequential configurations applying to the hardware
[e.g., RoCE], in which case the existing scheme might cause some
visible user delays.
This patch changes the completion scheme - instead of immediately
starting to sleep for a 'long' period, allow the device to quickly
poll on the first iteration after a couple of usecs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not
actually performing unicast MAC filtering.
While we're at it - relax a hard-coded limitation that limits each
interface into using at most 15 unicast MAC addresses before turning
promiscuous. Instead utilize the HW resources to their limit.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to hardware limitation, when transmitting a geneve-encapsulated
packet with more than 32 bytes worth of geneve options the hardware
would not be able to crack the packet and consider it a regular UDP
packet.
This implements the ndo_features_check() in qede in order to prevent
GSO on said transmitted packets.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GSO support for GRE and UDP tunnels
where outer checksums are enabled.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani says:
====================
act_mirred: Ingress actions support
This patch series implements action mirred 'ingress' actions
TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR.
This allows attaching filters whose target is to hand matching skbs into
the rx processing of a specified device.
v4:
in 4/4, check ret code of netif_receive_skb, as suggested by Cong Wang
v3:
in 4/4, addressed non coherency due to reading m->tcfm_eaction multiple
times, as spotted by Eric Dumazet
v2:
in 1/4, declare tcfm_mac_header_xmit as bool instead of int
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, 'action mirred' supported only egress actions (either
TCA_EGRESS_REDIR or TCA_EGRESS_MIRROR).
This patch implements the corresponding ingress actions
TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR.
This allows attaching filters whose target is to hand matching skbs into
the rx processing of a specified device.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move detection logic that tests whether device expects skb data to point
at mac_header upon xmit into a function.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'tcfm_ok_push' specifies whether a mac_len sized push is needed upon
egress to the target device (if action is performed at ingress).
Rename it to 'tcfm_mac_header_xmit' as this is actually an attribute of
the target device (and use a bool instead of int).
This allows to decouple the attribute from the action to be taken.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
