The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AVC protocol uses the same command for tuning and PID filtering and
since dvb-core uses a software zigzagging to do automatic retuning this
could cause all PID filters to be cleared. PID filter information is
now included in all DSD commands to the card.
Background:
There is a problem in the firedtv driver that causes recordings to stop
if the SW zigzag algorithm in dvb-core kicks in with a retune after the
application has set up the PID filters. Since tuning and setting PID
filters uses the same AVC command (DSD) and only the replace subfunction
is supported by the card, it is not possible to do a retune without
setting the PID filters. This means that the PID filtering has to be
sent in each tune.
This problem applies to C and T cards since S and S2 cards tune using a
vendor specific command. The patch corrects the problem by sending the
PID list in each tune. I have tested it on my T card with a good
result.
How to trigger problem: Zap to a channel and output AV to a file, e.g.
"tzap -c channels.conf SVT1 -r -o SVT1.ts". After a short while, pull
the antenna cable from the card. The lock on the channel will disappear
and the TS file will stop increasing in size. Wait a couple of seconds.
Replug the cable again. You will get a lock on the channel again, but
the TS file will never increase in size agains sinze no PIDS are
filtered.
Tested with kaffeine with DVB-T and DVB-C: Fixes retuning after antenna
was plugged out and back in with DVB-T. Does not fix this with DVB-C,
but also doesn't regress on DVB-C.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which fixes tuning to low frequency channels with
stb0899+tda8261 cards like the KNC TV-Station DVB-S2.
The cause of the issue was a broken if construct, which should have been
an if/else if, so that the setting for the lowest matching frequency is
applied.
Without this patch for example tuning to "arte" on Astra 19.2, 10744MHz
SR22000 failed most times and when it failed the communication between
driver and tda8261 was completely broken.
This problem disappears with the attached patch.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID (1b80:e400) for KWorld PlusTV Dual DVB-T Stick (DVB-T 399U).
The model number on the devices sticker label is "KW-DVB-T 399UR".
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems from other code that it is the dst_type field rather than the
type_flags field that contains values of the form DST_TYPE_IS...
The type_flags field contains values of the form DST_TYPE_HAS...
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ struct dst_state E; @@
(
*E.type_flags ==
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
|
*E.type_flags !=
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
)
// </smpl>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Humax/Coex DVB-T USB Stick 2.0 High Speed
which is a very popular tuner sold in Vietnam.
Tested with at least 3 tuners.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card includes Intel ce5039(Zarlink zl10039) tuner
and Intel ce6313 (Zarlink zl10313) demod.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code from Jan D. Louw with some minor changes.
http://article.gmane.org/gmane.linux.drivers.dvb/38163
Tested with TeVii S630 DVB-S USB card by me (Igor)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
do_div requires an u64 as the first argument, not a s64.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use unified lgs8gxx frontend instead of reverse engineered lgs8gl5 frontend.
After this patch, lgs8gl5 frontend could be mark as deprecated.
Future development should base on unified lgs8gxx frontend.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the STK7700D USB-DVB-Device.
lsusb identifies it as:
idVendor 0x1164 YUAN High-Tech Development Co., Ltd
idProduct 0x1efc
iProduct 2 STK7700D
The device is build into a Samsung R55-T5500 notebook.
Signed-off-by: Pete Hildebrandt <send2ph@googlemail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace printing to magically sized temporary buffer with use
of KERN_CONT for continual printing of eeprom registers dump.
Since deb_info is defined as dprintk, which is conditionally defined
to printk without additional parameters, meaning that deb_info is equivalent
to direct printk (without adding KERN_ facility), we can use KERN_DEBUG and
KERN_CONT in there, eliminating the need for sprintf into temporary buffer
with not easily readable/magical size.
Though it's strange, that deb_info definition uses printk without KERN_
facility and callers don't use it either.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create card parameters array in SDMC DM1105 driver.
It is useful for cards with the same pci id, but different
tuners, lnb power control circuits, etc.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In automatic mode every stop event on SDA line ends repetition.
However, in NetUP Dual card on the same i2c bus we have several devices.
If someone using both adapters to lock simultaneously or working with CAM interface
during lock procedure, it lead to end repetition prematurely quite often.
Set stv0900 i2c repeater to manual mode prevents such situation.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dvb-pll code should do the same thing that
alps_tdee4_stv0297_tuner_set_params() was doing. Except the dvb-pll code
will check for tuner presence when attaching, while the old code didn't.
This tuner appears to not be behind the stv0297's I2C gate but is instead
on a different I2C adapter provided by the flexcop chip. The old code
would turn the I2C gate off each time the tuner was used. I've changed it
to turn the gate off when the tuner is attached and then disable the gate
control function. This should result in the gate staying off, which should
be even better.
[hverkuil@xs4all.nl: fix compile error]
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code in skystar23_samsung_tbdu18132_tuner_set_params() and
samsung_tbmu24112_tuner_set_params() is equivalent to what the dvb-pll code
does. There could be an issue because the dvb-pll code will probe to check
for the tuner, while the previous code didn't do any checks.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code in samsung_tdtc9251dh0_calc_regs() is equivalent to what dvb-pll's
code does.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No datasheet, data take from code in flexcop driver. That code rounded
down the divisor rather than rounding to nearest, which was probably not
intentional and the dvb-pll code will round to nearest.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner parameters determined from code in flexcop driver. That code rounded
the divisor down instead of to the nearest value. This was probably not
intentional and the dvb-pll version will round to nearest.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner parameters taken from flexcop driver. This PLL has a 17 bit divisor
while the dvb-pll driver is designed for 15 bit divisors. It's not a
problem as 15 bits is enough for the tuner's entire range. But if a larger
range was wanted, it could be done by adding additional bands with the
extra divisor bits appearing as band switch bits.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No datasheet, tuner data comes from code in flexcop driver. This tuner is
also used on the AVerTV 771 supported by the bttv driver, but that code
uses a different tuner configuration, which is surprising.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Values for 'pid' range from 0 to 0x1fff. Therefore 'feed->pid' can never
be equal to both 'pid' and 0x2000. This makes the continue statement have
no effect.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DMX_ADD_PID allows to add multiple PIDs to a transport stream filter
previously set up with DMX_SET_PES_FILTER and output=DMX_OUT_TSDEMUX_TAP.
DMX_REMOVE_PID is used to drop a PID from a filter.
These ioctls are to be used by readers of /dev/dvb/adapterX/demuxY. They
may be called at any time, i.e. before or after the first filter on the
shared file descriptor was started.
They make it possible to record multiple services without the need to de-
or re-multiplex TS packets.
To accomplish this, dmxdev_filter->feed.ts has been converted to a list
of struct dmxdev_feeds, each containing a PID value and a pointer to a
struct dmx_ts_feed.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
lgs8gxx: add lgs8g75 demodulator support
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
input, inp and i are unsigned. When negative they are wrapped and caught by the
other test.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previous changesets broke Hauppauge devices and their GPIO configurations.
This changeset restores the LED & LNA functionality.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[].
Subsequently an attempt is made to load the firmware from the resulting
filename.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes most frontend drivers to allocate their state structure via
kzalloc and not kmalloc. This is done to properly initialize the
embedded "struct dvb_frontend frontend" field, that they all have.
The visible effect of this struct being uninitalized is, that the member "id"
that is used to set the name of kernel thread is totally random.
Some board drivers (for example cx88-dvb) set this "id" via
videobuf_dvb_alloc_frontend but most do not.
So I at least get random id values for saa7134, flexcop and ttpci based cards.
It looks like this in dmesg:
DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S)
The related kernel thread then also gets a strange name
like "kdvb-ad-1-fe--1".
Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Timothy Lee <timothy.lee@siriushk.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the following build warning:
sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'
Thanks to Hans Verkuil for pointing this out.
The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current GPIO configuration breaks all Hauppauge devices.
The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.
The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent patch didn't take into account that frontends can be compiled into
the kernel. Or that frontends compiled as modules can't be used by the
b2c2 driver if it is not a module itself.
Some frontends require multiple drivers, e.g. a demod driver and a tuner
driver. The code for the frontend support was getting added if the demod
driver was available. Change this to also require any needed tuner or SEC
drivers as well.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Request demodulator auto-detect transmission parameters in case of
garbage parameters provided by application for compatibility.
That's needed at least for MPlayer compatibility currently.
Thanks to Jelle de Jong for reporting issue and providing SSH access to
Devin for debugging.
Thanks to Devin Heitmueller for hard debug work he did to find that bug.
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
loaded for a given chip version. This would cause the optimization in
tuning not to be applied and thus a failed expectation, in tuning speed
increment. The patch swaps the tables in use. It also fixes a possible
one in a million condition where state->dev_ver implies an older Cut
(Cut < 2.0, eventhough the driver doesn't attach to any Cut older than
2.0) or even negative (due to a bad I2C bus master driver) for the card
combination.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing
out the issue at large.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_carloop_short’:
drivers/media/dvb/frontends/stv090x.c:2677: warning: ‘short_crl’ may be used uninitialized in this function
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks for Terry Wu for pointing out the missing entry.
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gcc 4.3.1 generates this warning:
v4l/smscoreapi.c: In function 'smscore_gpio_configure':
v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function
v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function
While in practice this will not happen, it is something that the compiler
can't determine. Initializing these two local variables to 0 suppresses
this warning.
Cc: Udi Atar <udi.linuxtv@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 1589a993f0 broke user visible
names of flexcop-pci devices, as it did reorder the enum of card types,
but did not adjust the array containing the card names.
Reorder the names, and uses [FC_AIR_DVBT] = "Air2PC/AirStar 2 DVB-T"
assignment style for more clarity.
It also adds the revision Number to the name for SkyStar rev. 2.3 and rev 2.6
as I think it is useful to see in log output.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove redundant code, which in the past handled the
various components (now independent modules) registrations.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new GPIO management interface to replace old (buggy) one.
Keeping old interface intact for now.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the SDIO interface driver a stand alone module.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two additional USB targets, add these to the 'cards' modules
and to the 'smsusb' module.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the debug message of the USB interface driver exit
function.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug that cause error log to echo also if success
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get common buffers() should block operation until valid buffer
is avaliable.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Assign using the new gpio structures, i/o for exist HPG
targets, without removing the old implementation.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card modules is the component which handles various targets,
so the IDs table should reside within it.
[mchehab@redhat.com: add missing smsendian.h include at smscoreapi.c]
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the infra-red to the makefile and declare
the assignment in the cards components.
[mchehab@redhat.com: Fixed a few trivial merge conflicts]
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add gpio look-up table for various requirements, any
target may select any gpio and assign it to a function
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the DVB-API v3 headers' include list from the core component
to the smsdvb (DVB adapter) which is the only one that uses them.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replace the old method of pulling the device status by
sending "get_statistics" request, to push mode. This make status update
much faster, and reduce various operation time (UHF scan now takes 15s
instead of 2m). In order to make the change the following modification
have been applied:
1) core header - update statistics headers.
2) dvb adapter - omit the statistics request, add handling of
status indications.
3) core 'onresponse' - re-route messages addressed to other adapter
to the dvb adapter.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for Siano protocol messages
with big endian systems.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a problem were protocol buffers
have been lost during USB disconnect events.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for byte ordering and big endianity
handling for the USB interface driver
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch updates the license of the USB interface driver
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove redundant complete instruction from smsdvb, in the
past this was used by the statistics state machine, but
no longer.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Siano: smsdvb - Fix license to match all other Siano's files
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Re-order the include files list
Re-order the include files list, put the DVB-API v3 within its
own section, within a define container.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modify the file license to match all other Siano's files
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code that modify the content of Siano's protocol
messages when running with big-endian target.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support for IR (infra-red)
remote controllers.
Further commits are needed in order to enable the
activation of the IR components.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some more indentation for the smscoreapi.h
There are no implementation changes in this patch.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
smscoreapi - move the main core structure declaration
to the header, in order to enable other components
(such as IR) to use it.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove two redundant lines, based on Klimov Alexey code review.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides SDIO interface driver for SMS (Siano Mobile
Silicon) based devices. The patch includes SMS high level SDIO driver
and requires patching the kernel SDIO stack, those stack patches had
been provided previously.
I would like to thank Pierre Ossman, MMC maintainer, who wrote this
driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fact that we now explicitly set fepriv->exit = 1 when the thread is
shutting down exposed an edge case where it was not being reset back to zero
once the thread went away in some cases. This resulted in failures in cases
where the frontend was closed, and then opened O_RDONLY, since in that case
the thread is not being restarted but it was checking the fepriv->exit flag.
Thanks to Thierry Lelegard, who and encountered and debugged a large portion
of the issue in the same twelve hours that I did (as well as testing my patch).
Cc: Thierry Lelegard <thierry.lelegard@tv-numeric.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for big endien target hosts, which
use USB interface.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A race condition was detected in the case that putting the tuner to sleep takes
an unusually long period of time, combined with applications that quickly
close/open the dvb frontend.
The kaffeine channel scanner closes and reopens the dvb frontend between each
tuning attempt. If it takes an unusually longer period of time to put the
tuner to sleep (for example, the Pinnacle 801e takes 660 ms), the dvb_frontend
thread will still be in a running state (and hence fepriv->thread is still set)
but the fepriv->exit field will still be zero. As a result, if a
dvb_frontend_start() call arrives while the frontend thread is in the process
of terminating, the call will return 0 without actually starting a new thread.
This results in the tuning request being dropped.
To address this, mark fepriv->exit as soon as we know the thread is going to
be terminated, so that dvb_frontend_start() knows to start a new instance.
Problem encountered with Kaffeine 0.8.7 doing ATSC scanning against the
Pinnacle 801e tuner, in conjunction with new code to power down the xc5000
when not in use.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
lgs8gxx: lgs8913 fake signal strength option default on. Original
calculation is too slow.
Signed-off-by: David T.L. Wong <davidtlwong <at> gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing __devexit_p() to several drivers. Also add a few missing
__init, __devinit and __exit markers. These errors could result in
build failures depending on the kernel configuration.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for QAM64 modulation type to the au8522 demod driver.
Signed-off-by: Frank Dischner <phaedrus961@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for SDMC DM1105 based DVB-S cards with PCI ID 195d:1105
Also create separate workqueue for demuxing.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add keymaps for TeVii and TBS USB DVB-S/S2 cards
Also module parameter named keymap inserted for override default keymap.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote control debugging for dw2102 driver based USB cards
It includes DVBWorld, TeVii, Terratec and others.
Type 'modprobe dvb-usb-dw2102 debug=4', then look at dmesg output.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frontend attachment code didn't handle cases where the frontend
partially failed to attach. For instance, when the demod was attached
successfully but the tuner driver wasn't compiled or fails to init for some
reason. In these cases we try to clean up the partial attachment and fail
instead of proceeding with a broken frontend.
If frontend registration fails, clean up with dvb_frontend_detach() rather
than just calling the frontend's main release method. The former does some
additional stuff, like release an attached tuner and take care of putting
symbols when dynamic binding is used.
In skystar2_rev23_attach() it's not necessary to set fc->dev_type, that
gets set before skystar2_rev23_attach() is called.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID (0458:4012) for Genius TVGo DVB-T03.
Thanks to Petr Vodicka <vodicka.petr@email.cz> for reporting and testing.
Tested-by: Petr Vodicka <vodicka.petr@email.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was causing a lock failure in Australia.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_dvr_read may unlock the dmxdev mutex and return -ENODEV, except this
function is a file op and will never be called with the mutex held.
There's existing mutex_lock and mutex_unlock around the actual read but
it's commented out. These should probably be uncommented but the read
blocks and this could block another non-blocking reader on the mutex
instead.
This change comments out the extra mutex_unlock.
[akpm@linux-foundation.org: cleanups, simplification]
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I have been informed by the manufacturer that the patch currently in the v4l tree to support the Genpix-CW3K version of the hardware will actually
damage the firmware on recent units. As he seems to not want this hardware supported in Linux, and I do not know how to detect the difference between
affected and not-affected units, I am requesting the immediate removal of support for this device. This patch removes a portion of the changeset
dce7e08ed2b1 applied 2007-08-18 relating to this specific device.
Adapted patch to not remove code, but to only to comment it out.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dibusb_i2c_xfer seems to do things very dangerous :
it assumes that it get only write/read request or write request.
That means that read can be understood as write. For example a program
doing
file = open("/dev/i2c-x", O_RDWR);
ioctl(file, I2C_SLAVE, 0x50)
read(file, data, 10)
will corrupt the eeprom as it will be understood as a write.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the USB IDs for the Terratec devices T3 and T5.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"Leadtek WinFast DTV Dongle H" is a hybrid digital/analog USB-stick TV
receiver. The code below allows the digital part to work with dvb_usb
in linux.
Signed-off-by: tomas petr <tom-petr@seznam.cz>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is reorganizing the frontend-attach mechanism in order to
gain noise-less (superflous prints) deactivation of submodules.
Credits go to Uwe Bugla for helping to clean and test the code.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reducing the print-levle of I2C error prints cleans some unwanted but
unavoidable errors from default syslog-level.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the xc5000 spec, the reset pin only needs to be held low for 10ms.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
av7110_av_start_play() should return 0 on success.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Discard PES packet if transport error indicator flag is set.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implemented TS replay capability.
audio/video devices are able to process PES and TS data now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, DVB-T is broken and this fixes it.
The PVRUSB2 has an odd I2C bus configuration where opening the i2c gate
on the digital and analog demod causes the tuner to fail. This needs
to be protected against for the PVRUSB2.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. Support Silicon Cut >= 3.0
2. Remove support for obsolete cuts: 1.0. 1.1. 1.2
3. Try to catch more error cases
Driver doesn't now attach to obsolete silcon cuts, It just simply quits.
Results in code simplification, with removal of the obsolete cuts.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes:
* Cut revision was read too late
* Missing increment
* wrong return value
* mismatched entries
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use external modulation
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: MAnu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: fix compilation when the new drivers aren't selected]
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for DVB-T for the following dibcom based
card:
Elgato EyeTV DTT deluxe (USB-ID: 0fd9:0020)
Signed-off-by: Armin Schenker <sar@snafu.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It both has unbalanced parentheses and == is not = and it's not used
anywhere anyway.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID (07ca:a805) for AverMedia AVerTV Volar GPS 805 (A805).
Thanks to Chris Brown <chrisneilbrown@gmail.com> for reporting and
testing.
Tested-by: Chris Brown <chrisneilbrown@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add 3rd dvb_usb_device_properties entry for upcoming USB IDs because
current entries are full.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Mike Isely <isely@pobox.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support to the dvb core to report the proper device name to
userspace for their devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch changes the dvb_usb_device_properties firmware field accordingly.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 34aecd2851 was made obsolete
and invalid by commit 40cf65d149.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch contains the unified driver for Legend Silicon LGS8913 and
LGS8GL5. It should replace lgs8gl5.c in media/dvb/frontends in the future.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch to provide basic support for DigitalNow TinyTwin Remote. It uses
same remote as TwinHan AzureWave AD-TU700(704J).
Signed-off-by: Stuart Hall <mailing-lists@enginuities.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID (07ca:850a) and configuration hack for AverMedia AVerTV Volar
Black HD (A850) DVB-T USB stick.
Tested-by: Olivier MENUEL <omenuel@laposte.net>
Tested-by: Thomas Renard <threnard@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove wrong GPIO definitions. GPIOs used by AF9015 are property of the
AF9013 demodulator and are coming from there.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID (15a4:901b) and remote for TrekStor DVB-T USB Stick.
Signed-off-by: Marc Schneider <macke@macke.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID (1b80:e395) for KWorld USB DVB-T TV Stick II (VS-DVB-T 395U).
Thanks to Julian Aron Prenner <julian@linux4you.it> for reporting this.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CE6230 DVB USB driver works correctly for the AVerMedia A310 USB2.0
DVB-T tuner. Add the required USB ID's and hardware names so that the
driver will handle it.
Signed-off-by: Juan Jesús García de Soria Lucena <skandalfo@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CUSTOMISE appears to be the one actually defined...
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no point in this, since the user can use the BUILTIN_FIRMWARE
option to include arbitrary firmware files directly in the kernel image.
Thanks to David Woodhouse for help.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
I2C_DRIVERIDs are no longer needed with v4l2_subdev and will be removed
from the kernel soon.
Cc: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for DVB-T for the following dibcom based card:
Elgato EyeTV DTT (USB-ID: 0fd9:0021)
Signed-off-by: Klaus Flittner <klaus@flittner.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the Yuan MC770 DVB-T (1164:0871).
Thanks to Xoan Loureiro.
Signed-off-by: Xoan Loureiro <x04n2.0@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the second part of the code cleanup changing the usb and pci-driver cores.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch cleans up the source code of the b2c2 flexcop-driver. It is the first of a total of two.
The code is now passing the checkpatch-script.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When resetting the PID-filter block a safety msleep(1) was injected. Now that the function is called from interrupt context, it was replaced with a udelay. It seems that this delay is not necessary at all, let's remove it for now and test a while.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a workaround in the i2c-code of the flexcop-driver to
fix support for SkyStar2 rev 2.7. There are not many devices out
there, that's why this bug was not revealed earlier.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the debug output from stb6100_cfg.h as it is flooding
the syslog with tuning data during normal operation.
Signed-off-by: Artem Makhutov <artem@makhutov.org>
Acked-by: Manu Abraham <abraham.manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the card is ejected on some systems you get a spew of messages as other
shared IRQ devices interrupt between the card eject and the card IRQ
disable.
We don't need to spew them all out
Closes#7472
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate tuning table for DVB-C solves tuning problem at 388MHz
TechnoTrend C-1501 DVB-C card does not lock on 388MHz. I assume that
existing frequency table is valid for DVB-T.
This is suggested by the name of the table: tda827xa_dvbt.
Added a table for DVB-C with the name tda827xa_dvbc.
Added runtime selection of the DVB-C table when the tuner is type
FE_QAM.
This should leave the behaviour of this driver with with DVB_T tuners
unchanged. This modification is in file tda827x.c
The tda827x.c gives the following warning message when debug=1:
tda827x: tda827x_config not defined, cannot set LNA gain!
Solved this by adding a tda827x_config struct in budget-ci.c.
Signed-off-by: Klaas de Waal <klaas.de.waal@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/ce6230.c: In function ‘ce6230_i2c_xfer’:
drivers/media/dvb/dvb-usb/ce6230.c:107: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several Kconfig items using CUSTOMIZE. Yet, most use the English
writing CUSTOMISE. This generates lots of trouble, because people sometimes type
the Kbuild item different.
Let's standardise every occurrence using the same syntax.
The changes were generated by this small shell script:
for i in `find linux -type f`; do sed s,CUSTOMIZE,CUSTOMISE,g $i >/tmp/a && mv /tmp/a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Randy Dunlap <randy.dunlap@oracle.com>:
ERROR: "dvb_dummy_fe_ofdm_attach" [drivers/media/video/cx231xx/cx231xx-dvb.ko] undefined!
This happens since cx231xx DVB part still misses the frontend modules.
So, the dummy frontend were used for development. The proper fix is to
implement the DVB modules there, as they will be required.
While this won't happen, lets allow the compilation with or without the
dummy FE testing module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au8522 is now dependent of V4L2, as reported by Randy Dunlap
<randy.dunlap@oracle.com>:
au8522_decoder.c:(.text+0x199898): undefined reference to `v4l2_ctrl_query_fill'
au8522_decoder.c:(.text+0x1998b3): undefined reference to `v4l2_ctrl_query_fill'
au8522_decoder.c:(.text+0x199944): undefined reference to `v4l2_device_unregister_subdev'
au8522_decoder.c:(.text+0x19997c): undefined reference to `v4l2_chip_ident_i2c_client'
au8522_decoder.c:(.text+0x199f1e): undefined reference to `v4l2_i2c_subdev_init'
Cc: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
normal_i2c and I2C_CLIENT_INSMOD are only necessary for kernels < 2.6.22.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per Hans Verkuil <hverkuil@xs4all.nl> instruction, remove the au8522_command
and replace v4l2-i2c-drv-legacy.h with v4l2-i2c-drv.h
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for reviewing the au8522 analog
support.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take a pass over all of the au0828/au8522 files and cleanup all the codingstyle
issues. This patch does not make *any* functional change to the code.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the g_chip_ident call work for the au0828/au8522. Discovered when testing
with the v4l2_compliance tool
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix merge conflict, due to a path change for analog demod]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Access using the hybrid state framework requires the list to be protected by
a mutex.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for reporting this during a
code review.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the analog functionality in the au8522 analog/digital
demodulator
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab: renamed drivers/media/video/au8522_decoder.c as drivers/media/dvb/frontends/au8522_decoder.c to avoid breaking bisect]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make use of the hybrid tuner framework so the analog and digital parts of the
au8522 demodulator can make use of the same shared state.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the au8522 is idle, put the chip into a low power mode (reduces power
consumption from 450ma to 346ma)
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the i2c messages to read and write registers, the two high order bits
of the first byte dictates whether it is a read or a write operation.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the au8522 state structure, as well as exposing functions needed by the
analog side of the demodulator into a common header file.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the au8522.c file to au8522_dig.c so that more source files can be
added to the driver while preserving the original name of au8522.ko
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It appears TS discontinuity about one per 10 hrs if CAM used.
Patch to fix it.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setting state->frontend.demodulator_priv to NULL in the event of
a kzalloc error will result in an OOPS. Just remove that line.
Thanks to Matthias Schwarzott for pointing this out.
Cc: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll start off with MODULE_VERSION("0.1")
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
small whitespace cleanup - space missing after the *
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Print a message in case the new software IRQ watchdog detects a problem.
I choose the info message category, this can be changed if not appropriate.
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was never any build-time dependency of the dib0700 usb module on the
dib0070 tuner module. Now that the build-time dependencies of dib0700 on
dib3000mc, dib7000p and dib7000m have been removed in the previous changesets,
we can enable DVB_FE_CUSTOMISE for these modules under config DVB_USB_DIB0700
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function prototype is defined but the function itself does not exist.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix dvb frontend debug variable to be static, to avoid linker
errors:
drivers/built-in.o:(.data+0xf4b0): multiple definition of `debug'
arch/x86/kernel/built-in.o:(.kprobes.text+0x90): first defined here
ld: Warning: size of symbol `debug' changed from 85 in arch/x86/kernel/built-in.o to 4 in drivers/built-in.o
It would also be Good if arch/x86/kernel/entry_32.S didn't have a
non-static 'debug' symbol. OTOH, it helps catch things like this one.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of asking a lot of questions for the poor users, let's just hide
the frontend customise menu, if the user doesn't want to customise.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dm1105 uses the ir_*() functions, so it needs to select VIDEO_IR
to avoid build errors:
dm1105.c:(.text+0x26b7ac): undefined reference to `ir_input_keydown'
dm1105.c:(.text+0x26b7bc): undefined reference to `ir_input_nokey'
(.devinit.text+0x29982): undefined reference to `ir_codes_dm1105_nec'
(.devinit.text+0x2998a): undefined reference to `ir_input_init'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for DVB-T for the following dibcom based card:
Sony PlayTV (USB-ID: 1415:0003)
Signed-off-by: Sebastián Blanes <sebastian.blanes@gmail.com>
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is based on initial work by Tino Reichardt and was heavily changed.
The datasheet of the zl10036 can be found here and on other places on the net:
http://www.mcmilk.de/projects/dvb-card/datasheets/ZL10036.pdf
The zl10038 is similar to the zl10036, so it is maybe possible to write a common
driver of necessary.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was a typo in the function
name, it should be lnbh24_attach, and not lnbp24_attach.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add last piece of code to support ST STV0900 dual demodulator.
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
