5000 series has issue supporting power save idle mode:
commit 9dc2153315
iwlwifi: always support idle mode for agn devices
For agn devices, always support idle mode which help power
consumption in idle unassociated state.
the above changes cause 5000 become not stable when power management is "on"
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2312
Cc: stable@kernel.org #2.6.39, #3.0.0
Reported-by: Devin J Pohly <djpohly+iwl@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may call rt2x00queue_pause_queue(queue) with queue == NULL. Bug
was introduced by commit 62fe778412
"rt2x00: Fix stuck queue in tx failure case" .
Cc: stable@kernel.org # 3.0+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced by commit
77b5621bac (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug has been introduced by:
d593411084
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Mon Jul 11 10:48:51 2011 +0300
iwlagn: simplify the bus architecture
Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should clear skb->data not skb itself. Bug was introduced by:
commit 0b8004aa12 "rt2x00: Properly
reserve room for descriptors in skbs".
Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver uses information from the self member of the pci_bus struct to
get information regarding the bridge to which the PCIe device is attached.
Unfortunately, this member is not established on all architectures, which
leads to a kernel oops.
Skipping the entire block that uses the self member to determine the bridge
vendor will only affect RTL8192DE devices as that driver sets the ASPM support
flag differently when the bridge vendor is Intel. If the self member is
available, there is no functional change.
This patch fixes Bugzilla No. 40212.
Reported-by: Hubert Liao <liao.hubertt@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [back to 2.6.38]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.
To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.
Bug was introduced by:
commit 53bc7aa08b
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date: Mon Apr 5 14:48:04 2010 +0530
ath9k: Add support for newer AR9285 chipsets.
Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462https://bugzilla.kernel.org/show_bug.cgi?id=37082https://bugzilla.redhat.com/show_bug.cgi?id=697157
however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).
Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If settings of tx power was deferred during scan or changing channel we
have to setup them during commit rxon. Fix problem on 3945 (4965 already
has this fix).
Optimize code to apply tx settings only when tx power was actually
changed.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With an uninitialized chainmask, the per-channel power will only contain
the power limits for a single chain instead of the combined tx power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9
gro: Only reset frag0 when skb can be pulled
...
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
wldev is freed in b43_one_core_detach() and should not be accessed after
that call. Keep wldev->dev in a local variable.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've fixed the last issue with BCMA support which caused memory
corruption on loading and unloading b43. Support for BCMA in b43 was
tested with 14e4:4353, 14e4:4357, 14e4:4727 and 14e4:4331. First two
cards (BCM43224 and BCM43225) are supported.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are only two capabilities we need, and both are trivial to find.
ath5k_hw_hasbssidmask() is true on AR5212, but not on AR5210 or AR5211.
ath5k_hw_hasveol() is true on AR5211 and AR5212, but not on AR5210,
according to the HAL source.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove b43's workarounds at the same time. Other users of
ssb_dma_translation do not support any 64-bit DMA devices, so they are
not affected.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Analyze of MMIO dumps from BCM43224, BCM43225, BCM4313 and BCM4331 has
shown that wl disables parity check for all that cards. This is required
for receiving any packets from the hardware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the current logging styles.
Add pr_fmt where appropriate.
Remove now unnecessary prefixes from printks.
Convert hard coded prefix to __func__.
Add a missing "\n" to a format.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices (e.g. Ubiquiti AirRouter) ship with broken EEPROM chainmask
data, which breaks the initial calibration after a hardware reset.
To fix this, mask the eeprom chainmask with the chainmask of the chip,
and use the chip chainmask if the result is zero.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the auto deep sleep mode has been enabled at driver init time
we should disable it at driver unloading to shutdown the function
gracefully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should consider current packet length also while checking
Tx aggregation buffer room.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For ad-hoc mode, RA is created for each peer connected. In case of
multicast traffic new RA will be created for each multicast
address. While processing Tx packets we have to go through this
RA list. We can avoid some RA nodes by sharing same RA for both
multicast and broadcast packets.
Therefore "memset(0xff)" is used to treat multicast packet as broadcast
one while choosing RA.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is since my patch:
iwlagn: introduce transport layer and implement rx_init
The IRQ is requested before the locks are initialized, hence the crash.
Initialize the tasklet before we request the IRQ on the way.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We now have iwlagn_set_dynamic_key() and
iwl_set_dynamic_key() which is confusing,
rename the former to iwlagn_send_sta_key()
to better reflect what it does -- it only
sends a command and doesn't change driver
state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Sometimes, when mac80211 changes the beacon
interval or when it isn't yet set in mac80211
before association, the uCode will sysassert
because we send it confusing RXON timing vs.
PAN parameters. To fix this, track the last
beacon interval sent to the device and use
that in PAN parameter calculations.
This fixes a bug during P2P group formation
as a client (and possibly association to a
regular AP) while connected to another AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Implement WoWLAN support in iwlagn. The device
supports a number of wakeup triggers and can do
GTK rekeying when asleep (if HW crypto is used).
Unfortunately, we need to disconnect from the AP
after resume since we can't yet get all the info
out of the wowlan uCode to stay connected safely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
As I just discovered while doing WoWLAN, HW crypto
is done wrong for GTKs: they should be programmed
for the AP station ID (in the managed mode case)
and the HW can actually deal with multiple group
keys per station as well (which is useful in IBSS
RSN but that I've chosen not to use this).
To fix all this, modify the way keys are sent to
the device and key offsets are allocated. After
these changes, key offsets are stored into the
hw_key_idx which we can then track for the key
lifetime, not relying on our sta_cmd array. WEP
default keys get special treatment, of course.
Additionally, since I had the API for it, we can
now pre-fill TKIP phase 1 keys for RX now that we
can obtain the P1K from mac80211, a capability I
had added for WoWLAN initially.
Finally, some keys simply don't need to be added
into the device's key cache -- a key that won't
be used for RX is only needed in the TX header,
so "pretend" to have accepted any key without
adding it into the device -- no need to use up
key space there for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It seems that due to merge issues between different
trees or so this function prototype wasn't removed
when it should have been, do it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn keeps a copy of key stuff internally but
never actually uses it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move tm_fixed_rate inside CONFIG_IWLWIFI_DEVICE_SVTOOL and only
available when the option is enable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
WoWLAN may need the NIC even after suspend. One should not do anything to the
NIC in the bus level, since one cannot check whether WoWLAN is enabled or not.
Same for resume.
Add a simple comment to the code to warn about this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The price to pay is the access to the log system. Therefore logs from bus layer
are sent by dev_printk instead of IWL_XXXX.
Rename bus->priv to bus->drv_data to make the separation even clearer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Call iwl_probe with a ready iwl_bus struct. This means that the bus layer
assigns the irq, dev and iwl_bus_ops pointers to iwl_bus before giving it to
iwl_probe.
The device specific struct is allocated together with the common iwl_bus struct
by the bus specific layer. The pointer to the aggregate struct is passed to the
upper layer that holds a pointer to iwl_bus instead of an embedded iw_bus.
The private data given to the PCI subsystem is now iwl_bus and not iwl_priv.
Provide bus_* inliners on the way in order to simplify the syntax.
Rename iwl-pci.h -> iwl-bus.h since it is bus agnostic and represent the
external of the bus layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It still holds a pointer to iwl_priv. But hopefully this will disappear at some point.
Also add the multiple inclusion protection to iwl-trans.h that was forgotten.
Move iwl-trans structures to iwl-trans.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This function is really related to the transport layer - move it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
