Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up some text output formatting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery from PF reset works better when you shorten up the delay
until the watchdog task executes.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counters in the 82599 Virtual Function are not clear on read. They
accumulate to the maximum value and then roll over. They are also not
cleared when the VF executes a soft reset, so it is possible they are
non-zero when the driver loads and starts. This has all been accounted
for in the code that keeps the stats up to date but there is one case
that is not. When the PF driver is reset the counters in the VF are
all reset to zero. This adds an additional accounting overhead into
the VF driver when the PF is reset under its feet. This patch adds
additional counters that are used by the VF driver to accumulate and
save stats after a PF reset has been detected. Prior to this patch
displaying the stats in the VF after the PF has reset would show
bogus data.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Simon Horman's feedback set IXGBE_RSC_CB(skb)->dma to zero
after unmapping HWRSC DMA address to avoid double freeing.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netdev_features_change is called before fcoe tx queues
setup is done, so this patch moves calling of netdev_features_change
after tx queues setup is done in ixgbe_init_interrupt_scheme, so
that real_num_tx_queues is updated correctly on each fcoe enable
or disable.
This allows additional fcoe queues updated correctly in vlan driver
for their correct queue selection.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX checksum offload does not work properly when transmitting
UDP packets with 0, 1 or 2 bytes of data. This patch works
around the problem by calculating checksums for these packets
in the driver.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advanced Power Management is disabled for 82599 KX4 connections by
clearing GRC.APME bit, causing it to not wake the system from an
improper system shutdown. By default GRC.APME is enabled and software
is not supposed to clear these settings during adapter probe.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 82599 link issues during driver load and unload test using multi-speed
10G & 1G fiber modules. When connected back to back sometime 82599 multispeed
fiber modules would link at 1G speed instead of 10G highest speed, due to a
race condition in autotry process involving Tx laser flapping. Move autotry
autoneg-37 tx laser flapping process from multispeed module init setup
to driver unload. This will alert the link partner to restart its
autotry process when it tries to establish the link with the link partner
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance driver version number after some bug fix.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Temporary stop the RX IRQ, and disable (sync) tasklet or napi.
And restore it after finished the vlgrp pointer assignment.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak while receiving 8021q tagged packet which is not
registered by user.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes UDP socket refcnt bugs in the pppol2tp driver.
A bug can cause a kernel stack trace when a tunnel socket is closed.
A way to reproduce the issue is to prepare the UDP socket for L2TP (by
opening a tunnel pppol2tp socket) and then close it before any L2TP
sessions are added to it. The sequence is
Create UDP socket
Create tunnel pppol2tp socket to prepare UDP socket for L2TP
pppol2tp_connect: session_id=0, peer_session_id=0
L2TP SCCRP control frame received (tunnel_id==0)
pppol2tp_recv_core: sock_hold()
pppol2tp_recv_core: sock_put
L2TP ZLB control frame received (tunnel_id=nnn)
pppol2tp_recv_core: sock_hold()
pppol2tp_recv_core: sock_put
Close tunnel management socket
pppol2tp_release: session_id=0, peer_session_id=0
Close UDP socket
udp_lib_close: BUG
The addition of sock_hold() in pppol2tp_connect() solves the problem.
For data frames, two sock_put() calls were added to plug a refcnt leak
per received data frame. The ref that is grabbed at the top of
pppol2tp_recv_core() must always be released, but this wasn't done for
accepted data frames or data frames discarded because of bad UDP
checksums. This leak meant that any UDP socket that had passed L2TP
data traffic (i.e. L2TP data frames, not just L2TP control frames)
using pppol2tp would not be released by the kernel.
WARNING: at include/net/sock.h:435 udp_lib_unhash+0x117/0x120()
Pid: 1086, comm: openl2tpd Not tainted 2.6.33-rc1 #8
Call Trace:
[<c119e9b7>] ? udp_lib_unhash+0x117/0x120
[<c101b871>] ? warn_slowpath_common+0x71/0xd0
[<c119e9b7>] ? udp_lib_unhash+0x117/0x120
[<c101b8e3>] ? warn_slowpath_null+0x13/0x20
[<c119e9b7>] ? udp_lib_unhash+0x117/0x120
[<c11598a7>] ? sk_common_release+0x17/0x90
[<c11a5e33>] ? inet_release+0x33/0x60
[<c11577b0>] ? sock_release+0x10/0x60
[<c115780f>] ? sock_close+0xf/0x30
[<c106e542>] ? __fput+0x52/0x150
[<c106b68e>] ? filp_close+0x3e/0x70
[<c101d2e2>] ? put_files_struct+0x62/0xb0
[<c101eaf7>] ? do_exit+0x5e7/0x650
[<c1081623>] ? mntput_no_expire+0x13/0x70
[<c106b68e>] ? filp_close+0x3e/0x70
[<c101eb8a>] ? do_group_exit+0x2a/0x70
[<c101ebe1>] ? sys_exit_group+0x11/0x20
[<c10029b0>] ? sysenter_do_call+0x12/0x26
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures the PHY correctly completes its reset before
setting register values.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for SMSC's LAN7500 family of USB 2.0
to gigabit ethernet adapters. It's loosely based on the smsc95xx
driver but the device registers for LAN7500 are completely different.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following warning introduced by commit
12bac0d9f4 ("proc: warn on non-existing
proc entries"):
WARNING: at /work/mips-linux/make/linux/fs/proc/generic.c:316 __xlate_proc_name+0xe0/0xe8()
name 'RBHMA4X00/RTL8019'
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that one error path (when alloc_skb fails) in netdev_tx
omits to unlock hw_priv->hwlock. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tristram Ha <Tristram.Ha@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a239a8b47c introduced a
noisy message, that fills up the log very fast.
The error seems not to be fatal (the connection is stable and
performance is ok), so make it IWL_DEBUG_TX rather than IWL_ERR.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable@kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I initially stumbled upon sequence number problems with PAE frames
in ath9k, I submitted a patch to remove all special cases for PAE
frames and let them go through the normal transmit path.
Out of concern about crypto incompatibility issues, this change was
merged instead:
commit 6c8afef551
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Tue Feb 9 10:07:00 2010 +0530
ath9k: Fix sequence numbers for PAE frames
After a lot of testing, I'm able to reliably trigger a driver crash on
rekeying with current versions with this change in place.
It seems that the driver does not support sending out regular MPDUs with
the same TID while an A-MPDU session is active.
This leads to duplicate entries in the TID Tx buffer, which hits the
following BUG_ON in ath_tx_addto_baw():
index = ATH_BA_INDEX(tid->seq_start, bf->bf_seqno);
cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
BUG_ON(tid->tx_buf[cindex] != NULL);
I believe until we actually have a reproducible case of an
incompatibility with another AP using no PAE special cases, we should
simply get rid of this mess.
This patch completely fixes my crash issues in STA mode and makes it
stay connected without throughput drops or connectivity issues even
when the AP is configured to a very short group rekey interval.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case debugfs does not init for some reason (or is disabled
on older kernels) driver does not allocate stats.fw_stats
structure, but tries to clear it later and trips on a NULL
pointer:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
PC is at __memzero+0x24/0x80
Backtrace:
[<bf0ddb88>] (wl1251_debugfs_reset+0x0/0x30 [wl1251])
[<bf0d6a2c>] (wl1251_op_stop+0x0/0x12c [wl1251])
[<bf0bc228>] (ieee80211_stop_device+0x0/0x74 [mac80211])
[<bf0b0d10>] (ieee80211_stop+0x0/0x4ac [mac80211])
[<c02deeac>] (dev_close+0x0/0xb4)
[<c02deac0>] (dev_change_flags+0x0/0x184)
[<c031f478>] (devinet_ioctl+0x0/0x704)
[<c0320720>] (inet_ioctl+0x0/0x100)
Add a NULL pointer check to fix this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HSO_AUTOPM is set by KConfig / set in the Kernel source, makefiles
and won't be ever set this way, therefor simply removing the protected
code.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_USE_INTERNAL_TIMER seems to be the remainings of some experiment.
It is explicitely #undef-ed as not working, only referenced from one
source file and rather aged.
Hereby cleaning it from the kernel tree.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The region set by the call to memset is immediately overwritten by the
subsequent call to memcpy.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to fp->tx_bp_prod is protected by __netif_tx_lock,
smp_mb() is not needed for that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to fp->tx_bd_prod is protected by __netif_tx_lock, so we do not
need any barrier for that.
Update of fp->tx_bd_cons in bnx2x_tx_int() is not protected by lock, but
barrier() nor smb_mb() in bnx2x_tx_avail() not guarantee we will see
values that is written on other cpu. Ordering issues between
netif_tx_stop_queue(), netif_tx_queue_stopped(), fp->tx_bd_cons = bd_cons
and bnx2x_tx_avail() are already handled by smp_mb() in bnx2x_tx_int()
and bnx2x_start_xmit().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we want to keep ordering of write to fp->bd_tx_cons and
netif_tx_queue_stopped(txq), what is read of txq->state, we have to use
general memory barrier.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The request to create an mccq was being dispatched without
doing a byte swap of num_pages. This byte swap is necessary
for Big Endian systems like PPC. Not having this fix leads
mccq create to fail on BE ASICs running newer version of
firmware, thereby causing driver initialization failure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate from the legacy PM hooks to use dev_pm_ops structure.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The davinci emac driver uses some ARM specific DMA APIs
for cache coherency which have been removed from kernel
with the 2.6.34 merge.
Modify the driver to use the dma_{map, unmap}_single() APIs
defined in dma-mapping.h
Without this fix, the driver fails to compile on Linus's
tree.
Tested on DM365 and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PCI pool changes were added to fix resume failures:
commit 98468efddb
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failu
and
commit 70abc8cb90
e100: Fix broken cbs accounting due to missing memset.
This introduced a problem that can happen if the TX ring size
is increased. We need to size the PCI pool using cbs->max
instead of the default cbs->count value.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
On Wed, 2010-03-10 at 08:41 -0800, David Miller wrote:
> From: Mikael Pettersson <mikpe@it.uu.se>
> Date: Wed, 10 Mar 2010 16:33:28 +0100
> > Booting 2.6.34-rc1 on a machine with a tulip nic I see
> > a number of kernel messages that include "(null)" where
> > previous kernels included the string "tulip0":
> CC:'ing the guilty party :-) It's one of the following
> commits:
Thanks Mikael.
Anonymity has some good attributes.
Blame avoidance is one of them.
I've broad shoulders. It's me, then Dwight Howard...
There might be another few of these where ->name or ->dev
was used before struct device or net_device was registered.
I'll go back and check.
tulip_core has:
if (tp->flags & HAS_MEDIA_TABLE) {
sprintf(dev->name, DRV_NAME "%d", board_idx); /* hack */
tulip_parse_eeprom(dev);
strcpy(dev->name, "eth%d"); /* un-hack */
}
So I don't feel _too_ bad.
tulip_parse_eeprom is done before register_netdev so the logging
there can not use netdev_<level> or dev_<level>(&dev->dev
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we always call rtnl_lock before going down the
error path in sky2_resume, which unlocks the rtnl lock.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The constant TG3_FLAG_10_100_ONLY should be used with the tg3_flags field,
not the tg3_flags2 field, as done elsewhere in the same file.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Fixed below compiler warning:
drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’:
drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of
1168 bytes is larger than 1024 bytes
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we read the IQ correction values (i_cal and q_cal) for G mode from a wrong
location (the same shifts as for A mode is applied which is incorrect). use
correct locations, matching the docs and HAL sources.
also we should write IQ correction only when we have that information in the
EEPROM, starting from version 4. also write it in the same way as we do in the
periodic recalibration (enable last), just to be sure.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.
1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd0f)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.
2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.
3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.
4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when using a fixed antenna we should use the antenna number in all tx
descriptors, otherwise the hardware will sometimes send the frame out on the
other antenna. it seems like the hardware does not always respect the default
antenna and diversity settings (esp. AR5K_STA_ID1_DEFAULT_ANTENNA).
also i would like to note that antenna diversity does not always work correctly
on 5414 (at least) when only one antenna is connected: for example all frames
might be received on antenna A but still the HW tries to send on antenna B some
times, causing packet loss.
this is both verified with the antenna statistics output of the previous patch
and a spectrum analyzer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee->networks consists of 128 struct libipw_network entries. If
we allocate this chunk of memory altogether, it ends up with an
order 4 page allocation. High order page allocation is likely to fail
on system high load. This patch splits the big chunk memory allocation
into small pieces, each is 344 bytes, allocates them with 128 times.
The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the
correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver
oopses on the target platform (Ralink rt3050 board).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some embedded ColdFire based boards use the SMC 91x family of ethernet
devices. (For example the Freescale M5249C3 and MoretonBay NETtel).
Add IO access support to the SMC91x driver, and allow this driver to
be configured for ColdFire platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
