Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime change of pause frame configuration (rx/tx flow control)
via ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now pass link drop status to FW on init/deinit. This is required
to inform FW that driver took/released a control on link.
FW then will manage its own state and device power profile based
on this information. To improve management we remove mpi_set
function which ambiguously took both state and speed parameters.
Deinit callback is now a part of FW ops, as it actually manages the FW.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented ring size setup, min/max validation and reconfiguration in
runtime.
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suffix UL to constant 1024 in order to give the compiler complete
information about the proper arithmetic to use. Notice that this
constant is used in a context that expects an expression of type
u64 (64 bits, unsigned) and following expressions are currently
being evaluated using 32-bit arithmetic:
qopt->idleslope * 1024 * ptr
qopt->hicredit * 1024 * 8
qopt->locredit * 1024 * 8
Addresses-Coverity-ID: 1470246 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470248 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470249 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SGMII was selected in the DT then the device should
write the SGMII enable bit.
If SGMII is not selected in the DT then the SGMII bit
should be disabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MD fixes from Shaohua Li:
"Two small fixes for MD:
- an error handling fix from me
- a recover bug fix for raid10 from BingJing"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid10: fix that replacement cannot complete recovery after reassemble
MD: cleanup resources in failure
Two fixes here which were breaking OpenRISC boot.
- Fix bug in __pte_free_tlb() exposed in 4.18 by Matthew Wilcox's page
table flag addition.
- Fix issue booting on real hardware if delay slot detection emulation
is disabled.
-----BEGIN PGP SIGNATURE-----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=7uxj
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/stffrdhrn/linux
Pull OpenRISC fixes from Stafford Horne:
"Two fixes for issues which were breaking OpenRISC boot:
- Fix bug in __pte_free_tlb() exposed in 4.18 by Matthew Wilcox's
page table flag addition.
- Fix issue booting on real hardware if delay slot detection
emulation is disabled"
* tag 'for-linus' of git://github.com/stffrdhrn/linux:
openrisc: entry: Fix delay slot exception detection
openrisc: Call destructor during __pte_free_tlb
Pull networking fixes from David Miller:
1) Verify netlink attributes properly in nf_queue, from Eric Dumazet.
2) Need to bump memory lock rlimit for test_sockmap bpf test, from
Yonghong Song.
3) Fix VLAN handling in lan78xx driver, from Dave Stevenson.
4) Fix uninitialized read in nf_log, from Jann Horn.
5) Fix raw command length parsing in mlx5, from Alex Vesker.
6) Cleanup loopback RDS connections upon netns deletion, from Sowmini
Varadhan.
7) Fix regressions in FIB rule matching during create, from Jason A.
Donenfeld and Roopa Prabhu.
8) Fix mpls ether type detection in nfp, from Pieter Jansen van Vuuren.
9) More bpfilter build fixes/adjustments from Masahiro Yamada.
10) Fix XDP_{TX,REDIRECT} flushing in various drivers, from Jesper
Dangaard Brouer.
11) fib_tests.sh file permissions were broken, from Shuah Khan.
12) Make sure BH/preemption is disabled in data path of mac80211, from
Denis Kenzior.
13) Don't ignore nla_parse_nested() return values in nl80211, from
Johannes berg.
14) Properly account sock objects ot kmemcg, from Shakeel Butt.
15) Adjustments to setting bpf program permissions to read-only, from
Daniel Borkmann.
16) TCP Fast Open key endianness was broken, it always took on the host
endiannness. Whoops. Explicitly make it little endian. From Yuching
Cheng.
17) Fix prefix route setting for link local addresses in ipv6, from
David Ahern.
18) Potential Spectre v1 in zatm driver, from Gustavo A. R. Silva.
19) Various bpf sockmap fixes, from John Fastabend.
20) Use after free for GRO with ESP, from Sabrina Dubroca.
21) Passing bogus flags to crypto_alloc_shash() in ipv6 SR code, from
Eric Biggers.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
qede: Adverstise software timestamp caps when PHC is not available.
qed: Fix use of incorrect size in memcpy call.
qed: Fix setting of incorrect eswitch mode.
qed: Limit msix vectors in kdump kernel to the minimum required count.
ipvlan: call dev_change_flags when ipvlan mode is reset
ipv6: sr: fix passing wrong flags to crypto_alloc_shash()
net: fix use-after-free in GRO with ESP
tcp: prevent bogus FRTO undos with non-SACK flows
bpf: sockhash, add release routine
bpf: sockhash fix omitted bucket lock in sock_close
bpf: sockmap, fix smap_list_map_remove when psock is in many maps
bpf: sockmap, fix crash when ipv6 sock is added
net: fib_rules: bring back rule_exists to match rule during add
hv_netvsc: split sub-channel setup into async and sync
net: use dev_change_tx_queue_len() for SIOCSIFTXQLEN
atm: zatm: Fix potential Spectre v1
s390/qeth: consistently re-enable device features
s390/qeth: don't clobber buffer on async TX completion
s390/qeth: avoid using is_multicast_ether_addr_64bits on (u8 *)[6]
s390/qeth: fix race when setting MAC address
...
Peng Li says:
====================
net: hns3: a few code improvements
This patchset removes some redundant code and fixes a few code
stylistic issues from internal concentrated review,
no functional changes introduced.
---
Change log:
V1 -> V2:
1, remove a patch according to the comment reported by David Miller.
---
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference to Documentation/DMA-API-HOWTO.txt,
Streaming DMA mappings which are usually mapped for one DMA transfer,
Network card DMA ring descriptors should use Consistent DMA mappings.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give default option for HNS3_HCLGE and HNS3_ENET will be helpful,
while dependency HNS3 is set. Meanwhile, use "if HNS3" section
instead of all the "depends on HNS3".
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some members in struct hns3_enet_tqp_vector, struct hnae3_client
and struct hnae3_ae_algo are unused.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set complete in the first hclge_cmd_csq_done of hclge_cmd_send,
and check if complete later, unnecessary to do hclge_cmd_csq_done
again.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
csq is used as a ring buffer, the value of the desc will be replaced
in next use. This patch removes the unnecessary memset, and just
updates the next_to_clean.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some redundant assignments.
desc->flag = cpu_to_le16(HCLGE_CMD_FLAG_NO_INTR | HCLGE_CMD_FLAG_IN)
has set bit HCLGE_CMD_FLAG_WR to zero, so does others.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some useless type cast, print in hclge_cmd_send.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_ring_to_dma_dir is unused anywhere.
This patch removes it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer zatm_dev is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'zatm_dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html
Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 8.1.0 complains:
drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_suspend.isra.1':
drivers/isdn/i4l/isdn_tty.c:790:3: warning:
'strncpy' output truncated before terminating nul copying
as many bytes from a string as its length
drivers/isdn/i4l/isdn_tty.c:778:6: note: length computed here
drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_resume':
drivers/isdn/i4l/isdn_tty.c:880:3: warning:
'strncpy' output truncated before terminating nul copying
as many bytes from a string as its length
drivers/isdn/i4l/isdn_tty.c:817:6: note: length computed here
Using strncpy() is indeed less than perfect since the length of data to
be copied has already been determined with strlen(). Replace strncpy()
with memcpy() to address the warning and optimize the code a little.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aac9 ("net: phy: realtek: add support for RTL8211")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently trace_sock_exceed_buf_limit() only show rmem info,
but wmem limit may also be hit.
So expose wmem info in this tracepoint as well.
Regarding memcg, I think it is better to introduce a new tracepoint(if
that is needed), i.e. trace_memcg_limit_hit other than show memcg info in
trace_sock_exceed_buf_limit.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.
Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>
If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed*: Fix series.
The patch series addresses few issues in the qed* drivers.
Please consider applying it to 'net' branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'mask' argument to crypto_alloc_shash() uses the CRYPTO_ALG_* flags,
not 'gfp_t'. So don't pass GFP_KERNEL to it.
Fixes: bf355b8d2c ("ipv6: sr: add core files for SR HMAC support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then
an out-of-bounds read on ipsec->sa will occur. Fix the
incorrect bounds check by using >= rather than >.
Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read")
Fixes: 7699353da8 ("netdevsim: add ipsec offload testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amritha Nambiar says:
====================
Symmetric queue selection using XPS for Rx queues
This patch series implements support for Tx queue selection based on
Rx queue(s) map. This is done by configuring Rx queue(s) map per Tx-queue
using sysfs attribute. If the user configuration for Rx queues does
not apply, then the Tx queue selection falls back to XPS using CPUs and
finally to hashing.
XPS is refactored to support Tx queue selection based on either the
CPUs map or the Rx-queues map. The config option CONFIG_XPS needs to be
enabled. By default no receive queues are configured for the Tx queue.
- /sys/class/net/<dev>/queues/tx-*/xps_rxqs
A set of receive queues can be mapped to a set of transmit queues (many:many),
although the common use case is a 1:1 mapping. This will enable sending
packets on the same Tx-Rx queue association as this is useful for busy polling
multi-threaded workloads where it is not possible to pin the threads to
a CPU. This is a rework of Sridhar's patch for symmetric queueing via
socket option:
https://www.spinics.net/lists/netdev/msg453106.html
Testing Hints:
Kernel: Linux 4.17.0-rc7+
Interface:
driver: ixgbe
version: 5.1.0-k
firmware-version: 0x00015e0b
Configuration:
ethtool -L $iface combined 16
ethtool -C $iface rx-usecs 1000
sysctl net.core.busy_poll=1000
ATR disabled:
ethtool -K $iface ntuple on
Workload:
Modified memcached that changes the thread selection policy to be based
on the incoming rx-queue of a connection using SO_INCOMING_NAPI_ID socket
option. The default is round-robin.
Default: No rxqs_map configured
Symmetric queues: Enable rxqs_map for all queues 1:1 mapped to Tx queue
System:
Architecture: x86_64
CPU(s): 72
Model name: Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz
16 threads 400K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 4/51/2215 2/30/5163
(usec)
intr/sec 26655 18606
contextswitch/sec 5145 4044
insn per cycle 0.43 0.72
cache-misses 6.919 4.310
(% of all cache refs)
L1-dcache-load- 4.49 3.29
-misses
(% of all L1-dcache hits)
LLC-load-misses 13.26 8.96
(% of all LL-cache hits)
-------------------------------------------------------------------------------
32 threads 400K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 10/112/5562 9/46/4637
(usec)
intr/sec 30456 27666
contextswitch/sec 7552 5133
insn per cycle 0.41 0.49
cache-misses 9.357 2.769
(% of all cache refs)
L1-dcache-load- 4.09 3.98
-misses
(% of all L1-dcache hits)
LLC-load-misses 12.96 3.96
(% of all LL-cache hits)
-------------------------------------------------------------------------------
16 threads 800K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 5/151/4989 9/69/2611
(usec)
intr/sec 35686 22907
contextswitch/sec 25522 12281
insn per cycle 0.67 0.74
cache-misses 8.652 6.38
(% of all cache refs)
L1-dcache-load- 3.19 2.86
-misses
(% of all L1-dcache hits)
LLC-load-misses 16.53 11.99
(% of all LL-cache hits)
-------------------------------------------------------------------------------
32 threads 800K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 6/163/6152 8/88/4209
(usec)
intr/sec 47079 26548
contextswitch/sec 42190 39168
insn per cycle 0.45 0.54
cache-misses 8.798 4.668
(% of all cache refs)
L1-dcache-load- 6.55 6.29
-misses
(% of all L1-dcache hits)
LLC-load-misses 13.91 10.44
(% of all LL-cache hits)
-------------------------------------------------------------------------------
v6:
- Changed the names of some functions to begin with net_if.
- Cleaned up sk_tx_queue_set/sk_rx_queue_set functions.
- Added sk_rx_queue_clear to make it consistent with tx_queue_mapping
initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend transmit queue sysfs attribute to configure Rx queue(s) map
per Tx queue. By default no receive queues are configured for the
Tx queue.
- /sys/class/net/eth0/queues/tx-*/xps_rxqs
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'skc_tx_queue_mapping' field in sock_common structure from
'int' to 'unsigned short' type with ~0 indicating unset and
other positive queue values being set. This will accommodate adding
a new 'unsigned short' field in sock_common in the next patch for
rx_queue_mapping.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use static_key for XPS maps to reduce the cost of extra map checks,
similar to how it is used for RPS and RFS. This includes static_key
'xps_needed' for XPS and another for 'xps_rxqs_needed' for XPS using
Rx queues map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor XPS code to support Tx queue selection based on
CPU(s) map or Rx queue(s) map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=KWL7
-----END PGP SIGNATURE-----
Merge tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few regression fixes for qgroup rescan status tracking and
the vm_fault_t conversion that mixed up the error values"
* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix mount failure when qgroup rescan is in progress
Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf
Pull vfs fix from Al Viro:
"Followup to procfs-seq_file series this window"
This fixes a memory leak by making sure that proc seq files release any
private data on close. The 'proc_seq_open' has to be properly paired
with 'proc_seq_release' that releases the extra private data.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
proc: add proc_seq_release
Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziQ7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynwZACgjpcPVTEiA0W02s4B/GhmVt1NMeUAnjgeLDzY
yRz6SX18lSmjHqCUXAk1
=/2QW
-----END PGP SIGNATURE-----
Merge tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems"
* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Return an ERR_PTR in ion_map_kernel
staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
iio: buffer: fix the function signature to match implementation
iio: mma8452: Fix ignoring MMA8452_INT_DRDY
iio: tsl2x7x/tsl2772: avoid potential division by zero
iio: pressure: bmp280: fix relative humidity unit
