We need to make sure our device is idle when rebooting a virtual
machine. This is done in the driver level.
The firmware will later handle FLR but we want to be extra safe and
stop the devices until the FLR is handled.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Up until now validation errors were counted in the parsing field
of the cs_counters struct, so we added a new counter and increased
it when needed.
In addition, there were some locations where only one of the counters
was updated (ctx or aggregate) so add the second one to be updated
as well.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When the firmware security is enabled, the pcie_aux_dbi_reg_addr
register in the PCI controller is blocked. Therefore, ignore
the result of writing to this register and assume it worked. Also
remove the prints on errors in the internal ELBI write function.
If the security is enabled, the firmware is responsible for setting
this register correctly so we won't have any problem.
If the security is disabled, the write will work (unless something
is totally broken at the PCI level and then the whole sequence
will fail).
In addition, remove a write to register pcie_aux_dbi_reg_addr+4,
which was never actually needed.
Moreover, PCIE_DBI registers are blocked to access from host when
firmware security is enabled. Use a different register to flush the
writes.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must fetch FW hard reset capability at every FW boot stage:
preboot, CPU boot, CPU application.
If hard reset is triggered, driver will take into consideration
only the last capability received.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case the clock gating was enabled in preboot we need to disable it
at the H/W initialization stage before touching the MME/TPC registers.
Otherwise, the ASIC can get stuck. If the security is enabled in
the firmware level, the CGM is always disabled and the driver can't
enable it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
hw_queues_mirror was renamed to cs_mirror, so revise accordingly a
comment that refers to this list.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We don't need to set EB on signal packets from collective slave
queues as it degrades performance. Because the slaves are the network
queues, the engine barrier doesn't actually guarantee that the
packet has been sent.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
FW hard reset capability indication is now moved to preboot stage.
Driver will check if HW is dirty only after it validated preboot
is up. If HW is dirty, driver will perform a hard reset according
to the FW capability.
In addition, FW defines a new message which driver need to send in
order to initiate a hard reset.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As we only fetch the CPU_PLL frequency in gaudi, we don't need a
generic get_pll_frequency function which takes a pll index as input
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When the F/W security is enabled, goya needs to fetch the PSOC pll
frequency through a dedicated interface
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the hashed
page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core do not
share an L2, allowing the scheduler to make better scheduling decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various parts of
the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to:
Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Ard
Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Colin Ian King, Daniel Axtens, David
Hildenbrand, Frederic Barrat, Ganesh Goudar, Gautham R. Shenoy, Geert
Uytterhoeven, Giuseppe Sacco, Greg Kurz, Harish, Jan Kratochvil, Jordan
Niethe, Kaixu Xia, Laurent Dufour, Leonardo Bras, Madhavan Srinivasan, Mahesh
Salgaonkar, Mathieu Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov,
Oliver O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej Siewior ,
Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe Kleine-König,
Vincent Stehlé, Youling Tang, Zhang Xiaoxu.
-----BEGIN PGP SIGNATURE-----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=Ga3K
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the
hashed page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core
do not share an L2, allowing the scheduler to make better scheduling
decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various
parts of the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to: Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Ard Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King,
Daniel Axtens, David Hildenbrand, Frederic Barrat, Ganesh Goudar,
Gautham R. Shenoy, Geert Uytterhoeven, Giuseppe Sacco, Greg Kurz,
Harish, Jan Kratochvil, Jordan Niethe, Kaixu Xia, Laurent Dufour,
Leonardo Bras, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov, Oliver
O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej
Siewior , Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe
Kleine-König, Vincent Stehlé, Youling Tang, and Zhang Xiaoxu.
* tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (304 commits)
powerpc/32s: Fix cleanup_cpu_mmu_context() compile bug
powerpc: Add config fragment for disabling -Werror
powerpc/configs: Add ppc64le_allnoconfig target
powerpc/powernv: Rate limit opal-elog read failure message
powerpc/pseries/memhotplug: Quieten some DLPAR operations
powerpc/ps3: use dma_mapping_error()
powerpc: force inlining of csum_partial() to avoid multiple csum_partial() with GCC10
powerpc/perf: Fix Threshold Event Counter Multiplier width for P10
powerpc/mm: Fix hugetlb_free_pmd_range() and hugetlb_free_pud_range()
KVM: PPC: Book3S HV: Fix mask size for emulated msgsndp
KVM: PPC: fix comparison to bool warning
KVM: PPC: Book3S: Assign boolean values to a bool variable
powerpc: Inline setup_kup()
powerpc/64s: Mark the kuap/kuep functions non __init
KVM: PPC: Book3S HV: XIVE: Add a comment regarding VP numbering
powerpc/xive: Improve error reporting of OPAL calls
powerpc/xive: Simplify xive_do_source_eoi()
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_EOI_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_MASK_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_SHIFT_BUG
...
In lkdtm.h, files targeted in comments are named "lkdtm_file.c" while
there are named "file.c" in directory.
Link: https://lkml.kernel.org/r/20201122162451.27551-6-laniel_francis@privacyrequired.com
Signed-off-by: Francis Laniel <laniel_francis@privacyrequired.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This new test ensures that fortified strscpy has the same behavior than
vanilla strscpy (e.g. returning -E2BIG when src content is truncated).
Finally, it generates a crash at runtime because there is a write overflow
in destination string.
Link: https://lkml.kernel.org/r/20201122162451.27551-5-laniel_francis@privacyrequired.com
Signed-off-by: Francis Laniel <laniel_francis@privacyrequired.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add code to test both:
- runtime detection of the overrun of a structure. This covers the
__builtin_object_size(x, 0) case. This test is called FORTIFY_OBJECT.
- runtime detection of the overrun of a char array within a structure.
This covers the __builtin_object_size(x, 1) case which can be used
for some string functions. This test is called FORTIFY_SUBOBJECT.
Link: https://lkml.kernel.org/r/20201122162451.27551-3-laniel_francis@privacyrequired.com
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Francis Laniel <laniel_francis@privacyrequired.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements.
-----BEGIN PGP SIGNATURE-----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=1A/T
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements"
* tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (72 commits)
dt-bindings: mmc: eliminate yamllint warnings
mmc: sdhci-xenon: introduce ACPI support
mmc: sdhci-xenon: use clk only with DT
mmc: sdhci-xenon: switch to device_* API
mmc: sdhci-xenon: use match data for controllers variants
dt-bindings: mmc: Fix xlnx,mio-bank property values for arasan driver
mmc: renesas_sdhi: populate hook for longer busy_wait
mmc: tmio: add hook for custom busy_wait calculation
mmc: tmio: set max_busy_timeout
dt-bindings: mmc: imx: fix the wrongly dropped imx8qm compatible string
mmc: sdhci-pci-gli: Disable slow mode in HS400 mode for GL9763E
mmc: sdhci: Use more concise device_property_read_u64
memstick: r592: Fix error return in r592_probe()
mmc: mxc: Convert the driver to DT-only
mmc: mxs: Remove the unused .id_table
mmc: sdhci-of-arasan: Fix fall-through warnings for Clang
mmc: sdhci-pci-gli: Reduce power consumption for GL9755
mmc: mediatek: depend on COMMON_CLK to fix compile tests
mmc: pxamci: Fix error return code in pxamci_probe
mmc: sdhci: Update firmware interface API
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in
from other trees/maintainers this merge window as well, as
driver subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some
long-time api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iEUQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynBJwCgjBAtVWXquZz4m/pyjn0HoTC7tdYAnAlQIj9s
vRbPjOgH9R+YRJzFs1Kx
=X6UP
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in from
other trees/maintainers this merge window as well, as driver
subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some long-time
api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)"
* tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
driver core: platform: don't oops in platform_shutdown() on unbound devices
ACPI: Use fwnode_init() to set up fwnode
misc: pvpanic: Replace OF headers by mod_devicetable.h
misc: pvpanic: Combine ACPI and platform drivers
usb: host: sl811: Switch to use platform_get_mem_or_io()
vfio: platform: Switch to use platform_get_mem_or_io()
driver core: platform: Introduce platform_get_mem_or_io()
dyndbg: fix use before null check
soc: fix comment for freeing soc_dev_attr
driver core: platform: use bus_type functions
driver core: platform: change logic implementing platform_driver_probe
driver core: platform: reorder functions
driver core: make driver_probe_device() static
driver core: Fix a couple of typos
driver core: Reorder devices on successful probe
driver core: Delete pointless parameter in fwnode_operations.add_links
driver core: Refactor fw_devlink feature
efi: Update implementation of add_links() to create fwnode links
of: property: Update implementation of add_links() to create fwnode links
driver core: Use device's fwnode to check if it is waiting for suppliers
...
Merge misc updates from Andrew Morton:
- a few random little subsystems
- almost all of the MM patches which are staged ahead of linux-next
material. I'll trickle to post-linux-next work in as the dependents
get merged up.
Subsystems affected by this patch series: kthread, kbuild, ide, ntfs,
ocfs2, arch, and mm (slab-generic, slab, slub, dax, debug, pagecache,
gup, swap, shmem, memcg, pagemap, mremap, hmm, vmalloc, documentation,
kasan, pagealloc, memory-failure, hugetlb, vmscan, z3fold, compaction,
oom-kill, migration, cma, page-poison, userfaultfd, zswap, zsmalloc,
uaccess, zram, and cleanups).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (200 commits)
mm: cleanup kstrto*() usage
mm: fix fall-through warnings for Clang
mm: slub: convert sysfs sprintf family to sysfs_emit/sysfs_emit_at
mm: shmem: convert shmem_enabled_show to use sysfs_emit_at
mm:backing-dev: use sysfs_emit in macro defining functions
mm: huge_memory: convert remaining use of sprintf to sysfs_emit and neatening
mm: use sysfs_emit for struct kobject * uses
mm: fix kernel-doc markups
zram: break the strict dependency from lzo
zram: add stat to gather incompressible pages since zram set up
zram: support page writeback
mm/process_vm_access: remove redundant initialization of iov_r
mm/zsmalloc.c: rework the list_add code in insert_zspage()
mm/zswap: move to use crypto_acomp API for hardware acceleration
mm/zswap: fix passing zero to 'PTR_ERR' warning
mm/zswap: make struct kernel_param_ops definitions const
userfaultfd/selftests: hint the test runner on required privilege
userfaultfd/selftests: fix retval check for userfaultfd_open()
userfaultfd/selftests: always dump something in modes
userfaultfd: selftests: make __{s,u}64 format specifiers portable
...
Building lkdtm with KASAN and Clang 11 or later results in the following
error when attempting to load the module:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle page fault for address: ffffffffc019cd70
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0011) - permissions violation
...
RIP: 0010:asan.module_ctor+0x0/0xffffffffffffa290 [lkdtm]
...
Call Trace:
do_init_module+0x17c/0x570
load_module+0xadee/0xd0b0
__x64_sys_finit_module+0x16c/0x1a0
do_syscall_64+0x34/0x50
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The reason is that rodata.o generates a dummy function that lives in
.rodata to validate that .rodata can't be executed; however, Clang 11 adds
KASAN globals support by generating module constructors to initialize
globals redzones. When Clang 11 adds a module constructor to rodata.o, it
is also added to .rodata: any attempt to call it on initialization results
in the above error.
Therefore, disable KASAN instrumentation for rodata.o.
Link: https://lkml.kernel.org/r/20201214191413.3164796-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
- fix NVMEM name with custom AT24 device name
-----BEGIN PGP SIGNATURE-----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=Kmok
-----END PGP SIGNATURE-----
Merge tag 'at24-fixes-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current
at24 fixes for v5.10
- fix NVMEM name with custom AT24 device name
There is no use for OF headers in the driver, but mod_devicetable.h
must be included. Update driver accordingly.
Cc: Peng Hao <peng.hao2@zte.com.cn>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201209203642.27648-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is nothing special in the driver that requires to have
a special ACPI driver for it. Combine both into simple
platform driver.
Cc: Peng Hao <peng.hao2@zte.com.cn>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201209203642.27648-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of the variable status must be one of the 0, -EIO and -EILSEQ, so
the switch case -ENODATA is unreached. Remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1605284071-6901-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We return 'err' in the error branch, but this variable may be set as
zero before. Fix it by setting 'err' as a negative value before we
goto the error label.
Fixes: e03327122e ("pci_endpoint_test: Add 2 ioctl commands")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/1605790158-6780-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'pci_set_dma_mask()' + 'pci_set_consistent_dma_mask()' can be replaced by
an equivalent 'dma_set_mask_and_coherent()' which is much less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201201210147.7917-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtsx_pcr:
add callback functions to support runtime PM
add delay_work to put device to D3 after idle
over 10 sec
rts5249:
add extra init flow for rtd3 and set rtd3_en from
config setting
rtsx_pci_sdmmc:
child device support autosuspend
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20201202065857.19412-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
changed rtsx_pci_disable_aspm() to rtsx_disable_aspm()
do not access ASPM configuration directly
changed pcie_capability_write_word() to _clear_and_set_word()
make sure only change PCI_EXP_LNKCTL bit8
make sure ASPM disable after extra_init_hw()
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20201202063228.18319-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in xpc_partition_disengaged() is clearly
intended to avoid canceling the timeout timer when the function is invoked
from the timer callback.
While in_interrupt() is deprecated and ill defined as it does not provide
what the name suggests it catches the intended case.
Add an argument to xpc_partition_disengaged() which is true if called
from timer and otherwise false.
Use del_timer_sync() instead of del_singleshot_timer_sync() which is the
same thing.
Note: This does not prevent reentrancy into the function as the function
has no concurrency control and timer callback and regular task context
callers can happen concurrently on different CPUs or the timer can
interrupt the task context before it is able to cancel it.
While the only driver which is providing the arch_xpc_ops callbacks
(xpc_uv) seems not to have a reentrancy problem and the only negative
effect would be a double dev_info() entry in dmesg, the whole mechanism is
conceptually broken.
But that's not subject of this cleanup endeavour and left as an exercise to
the folks who might have interest to make that code fully correct.
[bigeasy: Add the argument, use del_timer_sync().]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Cliff Whickman <cpw@sgi.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Russ Anderson <russ.anderson@hpe.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201119103151.ppo45mj53ulbxjx4@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The operation of get/set mode was same with get/set resolution. It is
a typo absolutely. This patch updates these bits operated by get/set
mode.
Signed-off-by: Zhou Xingxing <zhou_x1@hoperun.com>
Link: https://lore.kernel.org/r/1607334545-2091-1-git-send-email-zhou_x1@hoperun.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable protected audio video path client on mei client
bus.
Cc: Sean Z Huang <sean.z.huang@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20201116125612.1660971-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add API to support vtag in communication on mei bus.
Add mei_cldev_send_vtag, mei_cldev_recv_vtag and
mei_cldev_recv_nonblock_vtag functions to allow sending a message
with vtag set and to receive vtag of an incoming message.
Cc: Sean Z Huang <sean.z.huang@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20201116125612.1660971-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the fixes in here, and this resolves a merge issue with
drivers/misc/habanalabs/common/memory.c.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d162219c65.
The device uses a VIRTIO device ID out of a not-for-production range.
Releasing Linux using an ID out of this range will make it conflict with
development setups. An official request to reserve an ID for an MEI
device is yet to be submitted to the virtio TC, thus there's no chance
it will be reserved and fixed in time before the next release.
Once requested it usually takes 2-3 weeks to land in the spec, which
means the device can be supported with the official ID in the next Linux
version if contributors act quickly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Alexander Usyskin <alexander.usyskin@intel.com>
Cc: Wang Yu <yu1.wang@intel.com>
Cc: Liu Shuo <shuo.a.liu@intel.com>
Link: https://lore.kernel.org/r/20201205193625.469773-1-mst@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the "label" property is set on the AT24 EEPROM the NVMEM devid is
set to NVMEM_DEVID_NONE, but it is not effective since there is a
leftover line setting it back to NVMEM_DEVID_AUTO a few lines after.
Fixes: 61f764c307 ("eeprom: at24: Support custom device names for AT24 EEPROMs")
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add specific kernel traces which provide information on mmu notifier and on
pages range.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201125155013.39955-6-clombard@linux.vnet.ibm.com
Add invalidate_range mmu notifier, when required (ATSD access of MMIO
registers is available), to initiate TLB invalidation commands.
For the time being, the ATSD0 set of registers is used by default.
The pasid and bdf values have to be configured in the Process Element
Entry.
The PEE must be set up to match the BDF/PASID of the AFU.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201125155013.39955-5-clombard@linux.vnet.ibm.com
To complete the MMIO based mechanism, the fields: PASID, bus, device and
function of the Process Element Entry have to be filled. (See
OpenCAPI Power Platform Architecture document)
Hypervisor Process Element Entry
Word
0 1 .... 7 8 ...... 12 13 ..15 16.... 19 20 ........... 31
0 OSL Configuration State (0:31)
1 OSL Configuration State (32:63)
2 PASID | Reserved
3 Bus | Device |Function | Reserved
4 Reserved
5 Reserved
6 ....
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201125155013.39955-4-clombard@linux.vnet.ibm.com
Add a new CB IOCTL opcode that enables a user to query about a CB and
get its usage count.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Modify the CS counter of a CB to be atomic, so no locking is required
when it is being modified or read.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
hl_cs_sanity_checks() extracts the CS type bits of the CS flags, by
masking out the non-type bits.
To save the need for updating the function whenever new bits for
non-type flags are added, add an explicit mask for the CS type bits.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some messages should be changed to debug mode as we want to keep
minimal prints during normal operation of the device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If huge range is not valid, driver uses the host range also for
huge page allocations, but driver never frees its allocation.
This introduces a memory leak every time a user closes its context.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently, if the f/w is in preboot/u-boot they don't perform the new
reset mechanism. Therefore, the driver needs to reset the device.
To prevent reset of PCI_IF, the driver needs to first configure the
reset units.
If the security is enabled, the driver can't configure the reset units.
In that situation, don't reset the card.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
These defines are 64-bit defines so they need ull suffix.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
add support for user to request a timestamp upon
cs completion.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We want to indicate to the user that a certain command submission
is finished long time ago and it is no longer in database.
This means no further information regarding this cs can be obtained.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We have the ECC type field from the firmware but the driver didn't
print it, so we need to add that field to the ECC print message.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Make a function in gaudi.c to be static
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once firmware security is enabled, driver must fetch pll frequencies
through the firmware message interface instead of reading the registers
directly.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We introduce a new wrapper which allows us to mmu map any size
to any host va_range available. In addition we remove duplicated
code from various places in driver and using this new wrapper
instead.
This wrapper supports mapping only contiguous physical
memory blocks and will be used for mappings that are done to the
driver ASID.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We have several types of command submissions and the user wants to know
which type of command submission has not finished in time when that
event occurs. This is very helpful for debug.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As part of the security effort in which FW will be handling
sensitive HW registers, hard reset flow will be done by FW
and will be triggered by driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
F/W message returns 64bit value but up until now we casted it to
a 32bit variable, instead of receiving 64bit in the first place.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
After the MMU-code refactoring, the existing MMU debugfs operations
are no longer working so we need to fix them.
In addition, remove the duplicate code that was in the debugfs code
and use the already existing MMU-code.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Multiple locks are usually a source of problems, which in the MMU
case can be avoided since it is relatively rare that both MMU
tables are updated at the same time.
Therefore, use a single shared lock instead of two separate ones.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support for reserving va block with alignment different than
page size. This is a pre-requisite for allocations needed in future
ASICs
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add log prints for security and eFuse boot error bits
Signed-off-by: Guy Nisan <gnisan@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During hard-reset, the driver rejects further IOCTL calls and prints
an error message. That error message should be printed with the correct
device instead of using only the control device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once FW security is enabled there is no access to HBM ecc registers,
need to read values from FW using a dedicated interface.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must fetch FW hard reset capability during boot time,
in order to skip the hard reset flow if necessary.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Whether an ASIC has MMU towards its DRAM is an ASIC property, so
move it to the asic fixed properties structure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of using a dedicated va range for each internal pool,
we introduce a new way for reserving a va block from an existing
va range. This is a more generic way of reserving va blocks for
future use.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We want to handle the scenario in which the driver was not able
to kill all user processes due to many memory mappings.
We need to retry again after some period while releasing the cores.
The devices will be unusable and "in-reset" status during that time.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Future command submission types might be submitted to HW not via the
QMAN queues path. However, it would be still required to have the TDR
mechanism for these CS, and thus the patch renames the TDR fields and
replaces the hw_queues_ prefix with cs_.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Use an array of va_ranges instead of keeping each va_range separately,
we do this for better readability and in order to support access to
a specific range in a much elegant manner.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must verify if HW is dirty before trying to fetch preboot
information. Hence, we move this validation to a prior stage of
the boot sequence.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Due to using dma_mmap_coherent() to perform mmap of dma memory, we
had to clear the vm_pgoff field before calling that function.
However, that broke the userspace (profiler tool) as they relied
on searching the /proc/self/maps for these values to correctly
"disassemble" the topology recipe.
To re-enable that functionality, the driver can simply restore the
value of vm_pgoff before returning to userspace but after calling
dma_mmap_coherent().
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The new state indicates that device should be reset in order
to re-gain funcionality.
This unique state can occur if reset_on_lockup is disabled
and an actual lockup has occurred.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
One of the first steps of a hard reset flow is to close all open user
contexts. This user process teradown might take some time due to long
cleanup in our driver or some other reason even before our cleanup flow.
Hence fix the relevant print and comment to be more accurate.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Since the very large grace period is over and this functionality
prevents us to implement the new reset sequence and apply security
settings, we need to remove the code toggling the PCIE_EN bit in the
straps register.
Remove it for good.
Signed-off-by: Igor Grinberg <igrinberg@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We print twice the firmware status regarding security, once in
common code and once in asic code. Remove the print in asic code
and leave the common code print.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current CS jobs are no longer needed after their completion.
However, jobs of future workload might be in use even after they are
completed. To allow that, the patch adds a refcount to the job object,
and decouples its completion handling from its deallocation.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We need to have the MAX CS be much larger than the size of the
different queues. In GAUDI we have around 8 groups of queues, and each
group has 1K queue size. To prevent head-of-the-line blocking, we need
to make sure there is sufficient number of available CS allocations
even if one or more of those queues are full.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
failure in reading pre-boot verion is not handled correctly,
upon failure we need to reset the device in order to be able
to reinstall the driver.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Several header files are repeatedly included in many files.
Move these files to habanalabs.h which is included by all.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As in standard wait cs, we must release a signal fence once
a collective wait cs was dropped and not submitted.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There are no internal queues if H/W queues are being used.
In this case we can skip the redundant traversal over the queues array,
looking for internal queues.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Slightly refactor the cs_do_release() function, to reduce nesting level
and to ease the handling of future CS types.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Refactor the CS IOCTL handling by gathering common code into
sub-functions, in order to ease future additions of new CS types.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once FW security is enabled there is no access to PLL registers,
need to read values from FW using a dedicated interface.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This commit refactors the MMU code to support PCI MMU page tables
residing on host and DCORE MMU residing on the device DRAM at the
same time.
This is needed for future devices as on GAUDI and GOYA we have
a single MMU where its page tables always reside on DRAM.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In cases of multi-tenants, administrators may want to prevent data
leakage between users running on the same device one after another.
To do that the driver can scrub the internal memory (both SRAM and
DRAM) after a user finish to use the memory.
Because in GAUDI the driver allows only one application to use the
device at a time, it can scrub the memory when user app close FD.
In future devices where we have MMU on the DRAM, we can scrub the DRAM
memory with a finer granularity (page granularity) when the user
allocates the memory.
This feature is not supported in Goya.
To allow users that want to debug their applications, we add a kernel
module parameter to load the driver with this feature disabled.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Skip relevant HW configurations once FW security is enabled
because these configurations are being performed by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support for fetching security indication from FW.
This indication is needed in order to skip unnecessary
initializations done by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix cs counters structure in uapi to be one flat structure instead
of two instances of the same other structure.
use atomic read/increment for context counters so we could use
one structure for both aggregated and context counters.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Today driver is able to load a whole FW binary into a specific
location on ASIC. We add support for loading sections from the
same FW binary into different loactions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Although we get a valid cs type from the callee, in case new values
will be added in the future, it is best to check the expected values
in that function.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In GAUDI we don't have an MMU towards the HBM device memory. Therefore,
the user access that memory directly through physical address (via the
different engines) without the need to go through the driver to
allocate/free memory on the HBM.
For system monitoring purposes, the driver will keep track of the HBM
usage. This can be done as long as the user accurately reports the
allocations and releases of HBM memory, through the existing MEMORY
IOCTL uapi.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implement sync stream collective for GAUDI. Need to allocate additional
resources for that and add ctx_fini() to clean up those resources.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
DMA5 QMAN is designated to be used for reduction process, hence it will
be no longer configured as external queue.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Define new API for collective wait support and modify sync stream
common flow. In addition add kernel CB allocation support for
internal queues.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In the future there will be situations where queues can accept either
kernel allocated CBs or user allocated CBs, depending on different
states.
Therefore, instead of using a boolean variable of kernel/user allocated
CB, we need to use a bitmask to indicate that, which will allow to
combine the two options.
Add a flag to the uapi so the user will be able to indicate whether
the CB was allocated by kernel or by user. Of course the driver
validates that.
Signed-off-by: Tal Cohen <talcohen@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Initialize the QMANs that are responsible to submit doorbells to the NIC
engines. Add support for stopping and disabling them, and reset them as
part of the hard-reset procedure of GAUDI. This will allow the user to
submit work to the NICs.
Add support for receiving events on QMAN errors from the firmware.
However, the nic_ports_mask is still initialized to 0. That means this code
won't initialize the QMANs just yet. That will be in a later patch.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Configure the security properties of the NIC IP. This is to prevent the
user process from doing something with the NIC that he shouldn't do. e.g.
crash the server, steal data, etc.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add new structures and messages that the driver use to interact with the
firmware to receive information and events (errors) about GAUDI's NIC.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add auto-generated header files that describe the NIC QMANs registers
used by the driver.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We already check if queue index is smaller than max queues a few lines
above this check so no need to check this again.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Support advanced monitor functionality to monitor more than a
single SOB. In addition expand all CB generation functions
with buffer offset in order to put in them multiple packets that are
generated by different functions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case we are running without MMU enabled (debug mode), no need to
initialize the VM module in the driver.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
No need to print when the driver starts to initialize the H/W. Drivers
should be silent when everything is OK.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver now loads the firmware in two stages. For debugging purposes
we need to support situations where only the first stage firmware is
loaded.
Therefore, use a bitmask to determine which F/W is loaded
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
F/W can be loaded but device CPU queues disabled. In that case, HWMON
should be disabled. This is only relevant when debugging
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently mmu_prepare is located at context switch.
Since we support a single context, no reason to reconfigure
the MMU registers every context switch.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case we will have multiple contexts/processes, we can't just
increment aggregated counters. We need to make them atomic as they can
be incremented by multiple processes
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver never puts its device and control_device objects, hence
a memory leak is introduced every driver removal.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If huge range is not valid, driver uses the host range also for
huge page allocations, but driver never frees its allocation.
This introduces a memory leak every time a user closes its context.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is missing statement and missing "break;" in the ECC handling
code in gaudi.c
This will cause a wrong behavior upon certain ECC interrupts.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This patch fix clock timing for RTS5261, using 256 divide
for the version higher than version C.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1604397321-3026-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch check mmc support when RTS5261 initialize,
and not support mmc default.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1604397298-2921-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fix the bug that when there is over current but
reader can't enable OCP.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1604397278-2815-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add test mode for RTS5261.
If test mode is set, reader will switch to SD Express mode
mandatorily, and this mode is used by factory testing only.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1604397269-2780-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RTS5261 support SD mode and PCIe/NVMe mode. The workflow is as follows.
1.RTS5261 work in SD mode and set MMC_CAPS2_SD_EXP flag.
2.If card is plugged in, Host send CMD8 to ask card's PCIe availability.
3.If the card has PCIe availability and WP is not set, init_sd_express() will be invoked,
RTS5261 switch to PCIe/NVMe mode.
4.Mmc driver handover it to NVMe driver.
5.If card is unplugged, RTS5261 will switch to SD mode.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1603936668-3363-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To save the interested reader some time, add examples of AT25 part
numbers that correspond to EEPROMs rather than flashes.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20201107133337.1066271-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spelling of "Hisilicon" is modified.
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kai Ye <yekai13@huawei.com>
Link: https://lore.kernel.org/r/1604309965-21752-3-git-send-email-yekai13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interrupt cause is not relevant because of how the user use the
QMAN arbitration mechanism. We must mask it as the log explodes with it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We must relocate the coresight mmu configuration to the coresight
flow to make it work in case the first submission is to configure
the profiler.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
All throughout the driver, normal kernel pointers are
stored as 'u64' struct members, which is kind of silly
and requires casting through a uintptr_t to void* every
time they are used.
There is one line that missed the intermediate uintptr_t
case, which leads to a compiler warning:
drivers/misc/habanalabs/common/command_buffer.c: In function 'hl_cb_mmap':
drivers/misc/habanalabs/common/command_buffer.c:512:44: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
512 | rc = hdev->asic_funcs->cb_mmap(hdev, vma, (void *) cb->kernel_address,
Rather than adding one more cast, just fix the type and
remove all the other casts.
Fixes: 0db575350c ("habanalabs: make use of dma_mmap_coherent")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A receive callback is queued while the client is still connected
but can still be called after the client was disconnected. Upon
disconnect cl->me_cl is set to NULL, hence we need to check
that ME client is not-NULL in mei_cl_mtu to avoid
null dereference.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20201029095444.957924-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the initialization procedure for receive or receive callback
registration on the client bus has failed the caller can't re-run it.
Deinitilize the callback pointers and cancel the work
to allow the caller to retry.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20201029095444.957924-4-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid queuing reads and registering rx callbacks in
case the client is not connected, to prevent null
dereferencing and memory leaks.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20201029095444.957924-3-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/misc/ocxl/config.c:81: warning: Function parameter or member 'dev' not described in 'get_function_0'
drivers/misc/ocxl/config.c:81: warning: Excess function parameter 'device' description in 'get_function_0'
Cc: Frederic Barrat <fbarrat@linux.ibm.com>
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102142001.560490-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the 'c2dev' device data is not initialised when it's
allocated. There maybe an issue when using strncpy() to populate the
'name' attribute since a NUL terminator may not be provided in all
use-cases. To prevent such a failing, let's ensure the 'c2dev'
device data area is fully zeroed out on allocation.
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: "Eurotech S.p.A" <info@eurotech.it>
Cc: David Laight <David.Laight@aculab.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102142001.560490-1-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first condition of the if statement can never be true, because
bar variable is an enum variable type defined between 0 and 5, and
also bar variable acquires the value from arg function parameter which
is an unsigned long variable.
The constant 5 was replaced the the equivalent enum type, in this case
BAR_5.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/142cbbc215bed4243a219ea17b46f4256ceccb22.1603315690.git.gustavo.pimentel@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's some small fixes for 5.10-rc2 and a big driver removal.
The fixes are for some reported issues in the interconnect and coresight
drivers, nothing major.
The "big" driver removal is the MIC drivers have been asked to be
removed as the hardware never shipped and Intel no longer wants to
maintain something that no one can use. This is welcomed by many as the
DMA usage of these drivers was "interesting" and the security people
were starting to question some issues that were starting to be found in
the codebase.
Note, one of the subsystems for this driver, the "VOP" code, will
probably come back in future kernel versions as it was looking to
potentially solve some PCIe virtualization issues that a number of other
vendors were wanting to solve. But as-is, this codebase didn't work for
anyone else so no actual functionality is being removed.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX56scw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymMWQCgma6KXhD1HCox8T6fzWfp2tvCzEkAoI18n39v
8btS51MEfzk3FMZ7CP/7
=5Jsm
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes/removals from Greg KH:
"Here's some small fixes for 5.10-rc2 and a big driver removal.
The fixes are for some reported issues in the interconnect and
coresight drivers, nothing major.
The "big" driver removal is the MIC drivers have been asked to be
removed as the hardware never shipped and Intel no longer wants to
maintain something that no one can use. This is welcomed by many as
the DMA usage of these drivers was "interesting" and the security
people were starting to question some issues that were starting to be
found in the codebase.
Note, one of the subsystems for this driver, the "VOP" code, will
probably come back in future kernel versions as it was looking to
potentially solve some PCIe virtualization issues that a number of
other vendors were wanting to solve. But as-is, this codebase didn't
work for anyone else so no actual functionality is being removed.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: cti: Initialize dynamic sysfs attributes
coresight: Fix uninitialised pointer bug in etm_setup_aux()
coresight: add module license
misc: mic: remove the MIC drivers
interconnect: qcom: use icc_sync state for sm8[12]50
interconnect: qcom: Ensure that the floor bandwidth value is enforced
interconnect: qcom: sc7180: Init BCMs before creating the nodes
interconnect: qcom: sdm845: Init BCMs before creating the nodes
interconnect: Aggregate before setting initial bandwidth
interconnect: qcom: sdm845: Enable keepalive for the MM1 BCM
Driver has a trivial helper function to convert
the pointer argument and then call the native ioctl handler.
But now we have a generic implementation for that, so we can use it.
Signed-off-by: Harshal Chaudhari <harshalchau04@gmail.com>
Link: https://lore.kernel.org/r/20201026155801.16053-1-harshalchau04@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coccinelle suggested using PTR_ERR_OR_ZERO() and looking at the code,
we can use PTR_ERR_OR_ZERO() instead of checking IS_ERR() and then
doing 'return 0'.
Tested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20201026180026.3350-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the MIC drivers from the kernel tree
since the corresponding devices have been discontinued.
Removing the dma and char-misc changes in one patch and
merging via the char-misc tree is best to avoid any
potential build breakage.
Cc: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/8c1443136563de34699d2c084df478181c205db4.1603854416.git.sudeep.dutt@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull initial set_fs() removal from Al Viro:
"Christoph's set_fs base series + fixups"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Allow a NULL pos pointer to __kernel_read
fs: Allow a NULL pos pointer to __kernel_write
powerpc: remove address space overrides using set_fs()
powerpc: use non-set_fs based maccess routines
x86: remove address space overrides using set_fs()
x86: make TASK_SIZE_MAX usable from assembly code
x86: move PAGE_OFFSET, TASK_SIZE & friends to page_{32,64}_types.h
lkdtm: remove set_fs-based tests
test_bitmap: remove user bitmap tests
uaccess: add infrastructure for kernel builds with set_fs()
fs: don't allow splice read/write without explicit ops
fs: don't allow kernel reads and writes without iter ops
sysctl: Convert to iter interfaces
proc: add a read_iter method to proc proc_ops
proc: cleanup the compat vs no compat file ops
proc: remove a level of indentation in proc_get_inode
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
- Document R8A774A1, R8A774B1, R8A774E1 endpoint support in DT (Lad
Prabhakar)
- Add R8A774A1, R8A774B1, R8A774E1 (RZ/G2M, RZ/G2N, RZ/G2H) IDs to endpoint
test (Lad Prabhakar)
- Add device tree support for R8A7742 (Lad Prabhakar)
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
* remotes/lorenzo/pci/rcar:
dt-bindings: PCI: rcar: Add device tree support for r8a7742
PCI: rcar-gen2: Use fallthrough pseudo-keyword
misc: pci_endpoint_test: Add Device ID for RZ/G2H PCIe controller
dt-bindings: pci: rcar-pci-ep: Document r8a774e1
misc: pci_endpoint_test: Add Device ID for RZ/G2M and RZ/G2N PCIe controllers
dt-bindings: pci: rcar-pci-ep: Document r8a774a1 and r8a774b1
- A series from Nick adding ARCH_WANT_IRQS_OFF_ACTIVATE_MM & selecting it for
powerpc, as well as a related fix for sparc.
- Remove support for PowerPC 601.
- Some fixes for watchpoints & addition of a new ptrace flag for detecting ISA
v3.1 (Power10) watchpoint features.
- A fix for kernels using 4K pages and the hash MMU on bare metal Power9
systems with > 16TB of RAM, or RAM on the 2nd node.
- A basic idle driver for shallow stop states on Power10.
- Tweaks to our sched domains code to better inform the scheduler about the
hardware topology on Power9/10, where two SMT4 cores can be presented by
firmware as an SMT8 core.
- A series doing further reworks & cleanups of our EEH code.
- Addition of a filter for RTAS (firmware) calls done via sys_rtas(), to
prevent root from overwriting kernel memory.
- Other smaller features, fixes & cleanups.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Athira Rajeev, Biwen
Li, Cameron Berkenpas, Cédric Le Goater, Christophe Leroy, Christoph Hellwig,
Colin Ian King, Daniel Axtens, David Dai, Finn Thain, Frederic Barrat, Gautham
R. Shenoy, Greg Kurz, Gustavo Romero, Ira Weiny, Jason Yan, Joel Stanley,
Jordan Niethe, Kajol Jain, Konrad Rzeszutek Wilk, Laurent Dufour, Leonardo
Bras, Liu Shixin, Luca Ceresoli, Madhavan Srinivasan, Mahesh Salgaonkar,
Nathan Lynch, Nicholas Mc Guire, Nicholas Piggin, Nick Desaulniers, Oliver
O'Halloran, Pedro Miraglia Franco de Carvalho, Pratik Rajesh Sampat, Qian Cai,
Qinglang Miao, Ravi Bangoria, Russell Currey, Satheesh Rajendran, Scott
Cheloha, Segher Boessenkool, Srikar Dronamraju, Stan Johnson, Stephen Kitt,
Stephen Rothwell, Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, Vasant Hegde, Wang Wensheng, Wolfram Sang, Yang
Yingliang, zhengbin.
-----BEGIN PGP SIGNATURE-----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=akeX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- A series from Nick adding ARCH_WANT_IRQS_OFF_ACTIVATE_MM & selecting
it for powerpc, as well as a related fix for sparc.
- Remove support for PowerPC 601.
- Some fixes for watchpoints & addition of a new ptrace flag for
detecting ISA v3.1 (Power10) watchpoint features.
- A fix for kernels using 4K pages and the hash MMU on bare metal
Power9 systems with > 16TB of RAM, or RAM on the 2nd node.
- A basic idle driver for shallow stop states on Power10.
- Tweaks to our sched domains code to better inform the scheduler about
the hardware topology on Power9/10, where two SMT4 cores can be
presented by firmware as an SMT8 core.
- A series doing further reworks & cleanups of our EEH code.
- Addition of a filter for RTAS (firmware) calls done via sys_rtas(),
to prevent root from overwriting kernel memory.
- Other smaller features, fixes & cleanups.
Thanks to: Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Athira Rajeev, Biwen Li, Cameron Berkenpas, Cédric Le Goater, Christophe
Leroy, Christoph Hellwig, Colin Ian King, Daniel Axtens, David Dai, Finn
Thain, Frederic Barrat, Gautham R. Shenoy, Greg Kurz, Gustavo Romero,
Ira Weiny, Jason Yan, Joel Stanley, Jordan Niethe, Kajol Jain, Konrad
Rzeszutek Wilk, Laurent Dufour, Leonardo Bras, Liu Shixin, Luca
Ceresoli, Madhavan Srinivasan, Mahesh Salgaonkar, Nathan Lynch, Nicholas
Mc Guire, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran, Pedro
Miraglia Franco de Carvalho, Pratik Rajesh Sampat, Qian Cai, Qinglang
Miao, Ravi Bangoria, Russell Currey, Satheesh Rajendran, Scott Cheloha,
Segher Boessenkool, Srikar Dronamraju, Stan Johnson, Stephen Kitt,
Stephen Rothwell, Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, Vasant Hegde, Wang Wensheng, Wolfram Sang, Yang
Yingliang, zhengbin.
* tag 'powerpc-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (228 commits)
Revert "powerpc/pci: unmap legacy INTx interrupts when a PHB is removed"
selftests/powerpc: Fix eeh-basic.sh exit codes
cpufreq: powernv: Fix frame-size-overflow in powernv_cpufreq_reboot_notifier
powerpc/time: Make get_tb() common to PPC32 and PPC64
powerpc/time: Make get_tbl() common to PPC32 and PPC64
powerpc/time: Remove get_tbu()
powerpc/time: Avoid using get_tbl() and get_tbu() internally
powerpc/time: Make mftb() common to PPC32 and PPC64
powerpc/time: Rename mftbl() to mftb()
powerpc/32s: Remove #ifdef CONFIG_PPC_BOOK3S_32 in head_book3s_32.S
powerpc/32s: Rename head_32.S to head_book3s_32.S
powerpc/32s: Setup the early hash table at all time.
powerpc/time: Remove ifdef in get_dec() and set_dec()
powerpc: Remove get_tb_or_rtc()
powerpc: Remove __USE_RTC()
powerpc: Tidy up a bit after removal of PowerPC 601.
powerpc: Remove support for PowerPC 601
powerpc: Remove PowerPC 601
powerpc: Drop SYNC_601() ISYNC_601() and SYNC()
powerpc: Remove CONFIG_PPC601_SYNC_FIX
...
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4g8YQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yngKgCeNpArCP/9vQJRK9upnDm8ZLunSCUAn1wUT/2A
/bTQ42c/WRQ+LU828GSM
=6sO2
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (396 commits)
binder: fix UAF when releasing todo list
docs: w1: w1_therm: Fix broken xref, mistakes, clarify text
misc: Kconfig: fix a HISI_HIKEY_USB dependency
LSM: Fix type of id parameter in kernel_post_load_data prototype
misc: Kconfig: add a new dependency for HISI_HIKEY_USB
firmware_loader: fix a kernel-doc markup
w1: w1_therm: make w1_poll_completion static
binder: simplify the return expression of binder_mmap
test_firmware: Test partial read support
firmware: Add request_partial_firmware_into_buf()
firmware: Store opt_flags in fw_priv
fs/kernel_file_read: Add "offset" arg for partial reads
IMA: Add support for file reads without contents
LSM: Add "contents" flag to kernel_read_file hook
module: Call security_kernel_post_load_data()
firmware_loader: Use security_post_load_data()
LSM: Introduce kernel_post_load_data() hook
fs/kernel_read_file: Add file_size output argument
fs/kernel_read_file: Switch buffer size arg to size_t
fs/kernel_read_file: Remove redundant size argument
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXz5bNAAKCRCRxhvAZXjc
opfjAP9R/J72yxdd2CLGNZ96hyiRX1NgFDOVUhscOvujYJf8ZwD+OoLmKMvAyFW6
hnMhT1n9Q+aq194hyzChOLQaBTejBQ8=
=4WCX
-----END PGP SIGNATURE-----
Merge tag 'kernel-clone-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull kernel_clone() updates from Christian Brauner:
"During the v5.9 merge window we reworked the process creation
codepaths across multiple architectures. After this work we were only
left with the _do_fork() helper based on the struct kernel_clone_args
calling convention. As was pointed out _do_fork() isn't valid
kernelese especially for a helper that isn't just static.
This series removes the _do_fork() helper and introduces the new
kernel_clone() helper. The process creation cleanup didn't change the
name to something more reasonable mainly because _do_fork() was used
in quite a few places. So sending this as a separate series seemed the
better strategy.
I originally intended to send this early in the v5.9 development cycle
after the merge window had closed but given that this was touching
quite a few places I decided to defer this until the v5.10 merge
window"
* tag 'kernel-clone-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
sched: remove _do_fork()
tracing: switch to kernel_clone()
kgdbts: switch to kernel_clone()
kprobes: switch to kernel_clone()
x86: switch to kernel_clone()
sparc: switch to kernel_clone()
nios2: switch to kernel_clone()
m68k: switch to kernel_clone()
ia64: switch to kernel_clone()
h8300: switch to kernel_clone()
fork: introduce kernel_clone()
devices which doesn't need pinning of pages for DMA anymore. Add support
for the command submission to devices using new x86 instructions like
ENQCMD{,S} and MOVDIR64B. In addition, add support for process address
space identifiers (PASIDs) which are referenced by those command
submission instructions along with the handling of the PASID state on
context switch as another extended state. Work by Fenghua Yu, Ashok Raj,
Yu-cheng Yu and Dave Jiang.
-----BEGIN PGP SIGNATURE-----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=K9X4
-----END PGP SIGNATURE-----
Merge tag 'x86_pasid_for_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 PASID updates from Borislav Petkov:
"Initial support for sharing virtual addresses between the CPU and
devices which doesn't need pinning of pages for DMA anymore.
Add support for the command submission to devices using new x86
instructions like ENQCMD{,S} and MOVDIR64B. In addition, add support
for process address space identifiers (PASIDs) which are referenced by
those command submission instructions along with the handling of the
PASID state on context switch as another extended state.
Work by Fenghua Yu, Ashok Raj, Yu-cheng Yu and Dave Jiang"
* tag 'x86_pasid_for_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Add an enqcmds() wrapper for the ENQCMDS instruction
x86/asm: Carve out a generic movdir64b() helper for general usage
x86/mmu: Allocate/free a PASID
x86/cpufeatures: Mark ENQCMD as disabled when configured out
mm: Add a pasid member to struct mm_struct
x86/msr-index: Define an IA32_PASID MSR
x86/fpu/xstate: Add supervisor PASID state for ENQCMD
x86/cpufeatures: Enumerate ENQCMD and ENQCMDS instructions
Documentation/x86: Add documentation for SVA (Shared Virtual Addressing)
iommu/vt-d: Change flags type to unsigned int in binding mm
drm, iommu: Change type of pasid to u32
The dependency should be just USB_ROLE_SWITCH, instead
of CONFIG_USB_ROLE_SWITCH.
Fixes: 2827d98bc5 ("misc: Kconfig: add a new dependency for HISI_HIKEY_USB")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/0b6dff854c4bb412c2c11f17803e84d61385415f.1602138248.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As warned by Randy:
on x86_64:
CONFIG_USB_ROLE_SWITCH=m
and HISI_HIKEY_USB=y.
ld: drivers/misc/hisi_hikey_usb.o: in function `hisi_hikey_usb_remove':
hisi_hikey_usb.c:(.text+0x61): undefined reference to `usb_role_switch_unregister'
ld: hisi_hikey_usb.c:(.text+0xa4): undefined reference to `usb_role_switch_put'
ld: drivers/misc/hisi_hikey_usb.o: in function `hub_usb_role_switch_set':
hisi_hikey_usb.c:(.text+0xd3): undefined reference to `usb_role_switch_get_drvdata'
ld: drivers/misc/hisi_hikey_usb.o: in function `relay_set_role_switch':
hisi_hikey_usb.c:(.text+0x54d): undefined reference to `usb_role_switch_set_role'
ld: drivers/misc/hisi_hikey_usb.o: in function `hisi_hikey_usb_probe':
hisi_hikey_usb.c:(.text+0x8a5): undefined reference to `usb_role_switch_get'
ld: hisi_hikey_usb.c:(.text+0xa08): undefined reference to `usb_role_switch_register'
ld: hisi_hikey_usb.c:(.text+0xa6e): undefined reference to `usb_role_switch_put'
Make it dependent on CONFIG_USB_ROLE_SWITCH.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/0e49432d0db9ee8429a9923a1d995935b6b83552.1602047370.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update UV MMRs in uv_mmrs.h for UV5 based on Verilog output from the
UV Hub hardware design files. This is the next UV architecture with
a new class (UVY) being defined for 52 bit physical address masks.
Uses a bitmask for UV arch identification so a single test can cover
multiple versions. Includes other adjustments to match the uv_mmrs.h
file to keep from encountering compile errors. New UV5 functionality
is added in the patches that follow.
[ Fix W=1 build warnings. ]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lkml.kernel.org/r/20201005203929.148656-5-mike.travis@hpe.com
Remove the define is_uv() is_uv_system and just use the latter as is.
This removes a conflict with a new symbol in the generated uv_mmrs.h
file (is_uv()).
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lkml.kernel.org/r/20201005203929.148656-4-mike.travis@hpe.com
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Read and write io memory should address align on ARCH ARM. Change to use
memcpy_toio to avoid kernel panic caused by the address un-align issue.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929091106.24624-5-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since struct _mic_vring_info and vring are allocated together and follow
vring, if the vring_size() is not four bytes aligned, which will cause
the start address of struct _mic_vring_info is not four byte aligned.
For example, when vring entries is 128, the vring_size() will be 5126
bytes. The _mic_vring_info struct layout in ddr looks like:
0x90002400: 00000000 00390000 EE010000 0000C0FF
Here 0x39 is the avail_idx member, and 0xC0FFEE01 is the magic member.
When EP use ioread32(magic) to reads the magic in RC's share memory, it
will cause kernel panic on ARM64 platform due to the cross-byte io read.
Here read magic in user space use le32toh(vr0->info->magic) will meet
the same issue.
So add round_up(x,4) for vring_size, then the struct _mic_vring_info
will store in this way:
0x90002400: 00000000 00000000 00000039 C0FFEE01
Which will avoid kernel panic when read magic in struct _mic_vring_info.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929091106.24624-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set VIRTIO_F_ACCESS_PLATFORM feature for vop driver, as the DMA mapping
details shouldn't decide on the virtio implementation, but the host PCIe
implementation.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929084944.24146-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When OCXL is enabled and HOTPLUG_PCI is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for HOTPLUG_PCI_POWERNV
Depends on [n]: PCI [=y] && HOTPLUG_PCI [=n] && PPC_POWERNV [=y] && EEH [=y]
Selected by [y]:
- OCXL [=y] && PPC_POWERNV [=y] && PCI [=y] && EEH [=y]
The reason is that OCXL selects HOTPLUG_PCI_POWERNV without depending on
or selecting HOTPLUG_PCI while HOTPLUG_PCI_POWERNV is subordinate to
HOTPLUG_PCI.
HOTPLUG_PCI_POWERNV is a visible symbol with a set of dependencies.
Selecting it will lead to overlooking its other dependencies as well.
Let OCXL depend on HOTPLUG_PCI_POWERNV instead to avoid Kbuild issues.
Fixes: 49ce94b867 ("ocxl: Add PCI hotplug dependency to Kconfig")
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20200918094148.20525-1-fazilyildiran@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-14-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates dma_buf_vmap() and dma-buf's vmap callback to use
struct dma_buf_map.
The interfaces used to return a buffer address. This address now gets
stored in an instance of the structure that is given as an additional
argument. The functions return an errno code on errors.
Users of the functions are updated accordingly. This is only an interface
change. It is currently expected that dma-buf memory can be accessed with
system memory load/store operations.
v3:
* update fastrpc driver (kernel test robot)
v2:
* always clear map parameter in dma_buf_vmap() (Daniel)
* include dma-buf-heaps and i915 selftests (kernel test robot)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925115601.23955-3-tzimmermann@suse.de
- add support for masking sensitive data in VAIO EEPROMs
- set the nvmem TYPE to NVMEM_TYPE_EEPROM
- add support for the new 'label' property
- set the nvmem ID to NVMEM_DEVID_AUTO by default (for backward
compatibility) or to NVMEM_DEVID_NONE if label is defined
-----BEGIN PGP SIGNATURE-----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=KexW
-----END PGP SIGNATURE-----
Merge tag 'at24-updates-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.10
at24 updates for v5.10
- add support for masking sensitive data in VAIO EEPROMs
- set the nvmem TYPE to NVMEM_TYPE_EEPROM
- add support for the new 'label' property
- set the nvmem ID to NVMEM_DEVID_AUTO by default (for backward
compatibility) or to NVMEM_DEVID_NONE if label is defined
By using the label property, a more descriptive name can be populated
for AT24 EEPROMs NVMEM device. Update the AT24 driver to check to see
if the label property is present and if so, use this as the name for
NVMEM device. Please note that when the 'label' property is present for
the AT24 EEPROM, we do not want the NVMEM driver to append the 'devid'
to the name and so the nvmem_config.id is initialised to
NVMEM_DEVID_NONE.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
LDMA registers are configured with a fixed value.
We add new define set which gives the configuration
a proper meaning.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The device should be idle after a context is closed. If not, print a
notice.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
During debugging of error we sometimes need to know whether the error
happened when a user context was open. Add debug prints when opening and
closing user contexts.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Some engines use resources that belong to the kernel context (e.g. MMU
mappings). In case the halt-engines doesn't work properly due to H/W
restriction, we need to make sure the kernel context lives on until after
the hw_fini. The hw_fini resets the ASIC after that no engine is alive and
we can safely close the kernel context.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
We don't try to allocate huge pages here so remove the huge word.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The AT24 EEPROM driver does not initialise the 'id' field of the
nvmem_config structure and because the entire structure is not
initialised, it ends up with a random value. This causes the NVMEM
driver to append the device 'devid' value to name of the NVMEM
device. Ideally for I2C devices such as the AT24 that already have a
unique name, we would not bother to append the 'devid'. However, given
that this has always been done for AT24 devices, we cannot remove the
'devid' as this will change the name of the userspace sysfs node for
the NVMEM device. Nonetheless we should ensure that the 'id' field of
the nvmem_config structure is initialised so that there is no chance of
a random value causes problems in the future. Therefore, set the NVMEM
config.id to NVMEM_DEVID_AUTO for AT24 EEPROMs so that the 'devid' is
always appended.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The commit 0a121f9bc3 ("misc: pci_endpoint_test: Use streaming DMA
APIs for buffer allocation") changed to use streaming DMA APIs, however,
dma_map_single() might not return a 4KB aligned address, so add the
default_data as driver data for Layerscape PCIe controllers to make it
4KB aligned.
Link: https://lore.kernel.org/r/20200918080024.13639-13-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Add LS1088a in pci_device_id table so that pci-epf-test can be used
for testing PCIe EP in LS1088a.
Link: https://lore.kernel.org/r/20200918080024.13639-12-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
This return statement is indented one tab too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200918143405.GF909725@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inside __scif_pin_pages(), when map_flags != SCIF_MAP_KERNEL it
will call pin_user_pages_fast() to map nr_pages. However,
pin_user_pages_fast() might fail with a return value -ERRNO.
The return value is stored in pinned_pages->nr_pages. which in
turn is passed to unpin_user_pages(), which expects
pinned_pages->nr_pages >=0, else disaster.
Fix this by assigning pinned_pages->nr_pages to 0 if
pin_user_pages_fast() returns -ERRNO.
Fixes: ba612aa8b4 ("misc: mic: SCIF memory registration and unregistration")
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Link: https://lore.kernel.org/r/1600570295-29546-1-git-send-email-jrdr.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of devm_platform_ioremap_resource() provided by driver
core platform instead of duplicated analogue.
Acked-by: Arnd Bergmann <arn@arndb.de>
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20200918083634.33124-1-bobo.shaobowang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our firmware use some scratchpad registers in the device for different
roles. Update the file to the latest version of the firmware code.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Future F/W versions will have enhanced security measures and the driver
won't be able to do certain configurations that it always did and those
configurations will be done by the firmware.
We use the firmware's preboot version to determine whether security
measures are enabled or not. Because we need this very early in our code,
the read of the preboot version is moved to the earliest possible place,
right after the device's PCI initialization.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This is a workaround for H/W bug H3-2116, where if there are more than 16
outstanding completions in the DMA transpose engine, there can be a
deadlock in the engine.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add new packet to fetch PLL information from firmware. This will be needed
in the future when the driver won't be able to access the PLL registers
directly
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There are cases in which the device should access the host memory of a
CB through the device MMU, and thus this memory should be mapped.
The patch adds a flag to the CB IOCTL, in which a user can ask the
driver to perform the mapping when creating a CB.
The mapping is allowed only if a dedicated VA range was allocated for
the specific ASIC.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Future changes require using a context while handling a command buffer,
and thus need to save the context in the command buffer object.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Now that the driver no longer uses dma_buf, we can remove the select of
DMA_SHARED_BUFFER from kconfig.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The user sometimes wants to check if a CS has completed to clean resources.
In that case, the user doesn't want to sleep but just to check if the CS
has finished and continue with his code.
Add a new definition to the API of the wait on CS. The new definition says
that if the timeout is 0, the driver won't sleep at all but return
immediately after checking if the CS has finished.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The firmware running in the boot stage takes more time to execute due to
increased security mechanisms. Therefore, we need to increase the timeout
we wait for the boot fit to finish loading.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This commit modify the existing debugfs code to support future devices that
have a 6 HOPs MMU implementation instead of 5 HOPs implementation.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This commit adds the number of HOPs supported by the device to the
device MMU properties.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
As preparation to MMU v2, rework MMU to be device oriented
instantiated according to the device in hand.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
In the future we will have MMU v2 code, so we need to prepare the
driver for it. The first step is to rename the current MMU file to
mmu_v1.c.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Change the acquiring of a device virtual address for mapping by using the
smallest possible alignment, rather than the biggest, depending on the
page size used by the user for allocating the memory. This will lower the
virtual space memory consumption.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
For consistency with GAUDI code, add check of the relevant flag in the
device structure before resetting the GOYA device in case of firmware
event.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
For future ASICs, we increase this field by one nibble. This field was not
used by the current ASICs so this change doesn't break anything.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Because the device CPU compiler aligns structures to 8 bytes,
struct cpucp_info has an alignment issue as some parts
in the structure are not aligned to 8 bytes.
It is preferred that we explicitly insert placeholders inside
the structure to avoid confusion
in order to validate this scenario, we printed both pointers:
__u8 cpucp_version[VERSION_MAX_LEN]; (0xffff899c67ed4cbc)
__le64 dram_size; (0xffff899c67ed4d40)
we see difference of 132 bytes although the first array
is only 128 bytes long, Meaning compiler added a 4 byte padding.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There were a couple of comments where the name ArmCP was still used. Rename
it to CPU-CP.
In addition, rename ArmCP or ARM in log messages to "device CPU".
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There is a case where the user reaches the maximum number of CS in-flight.
In that case, the driver rejects the new CS of the user with EAGAIN. Count
that event so the user can query the driver later to see if it happened.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add dma_mmap_coherent() for goya and gaudi to match their use of
dma_alloc_coherent(), see the Link tag for why.
Link: https://lore.kernel.org/lkml/20200609091727.GA23814@lst.de/
Cc: Christoph Hellwig <hch@lst.de>
Cc: Zhang Li <li.zhang@bitmain.com>
Cc: Ding Z Nan <oshack@hotmail.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The driver use vm_pgoff to hold the CB idr handle. Before we actually call
the mapping function, we need to clear the handle so there won't be any
garbage left in vm_pgoff.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Arrange the hl_mmap code to be more structured and expandable for the
future. Add better defines that describe our usage of the vm_pgoff.
Note that I shamelessly took the code and defines from the amdkfd driver
(my previous driver).
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
When shifting a boolean variable by more than 31 bits and putting the
result into a u64 variable, we need to cast the boolean into unsigned 64
bits to prevent possible overflow.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
ArmCP mandates that the device CPU is always an ARM processor, which might
be wrong in the future.
Most of this change is an internal renaming of variables, functions and
defines but there are two entries in sysfs which have armcp in their
names. Add identical cpucp entries but don't remove yet the armcp entries.
Those will be deprecated next year. Add the documentation about it in sysfs
documentation.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add driver implementation for reading the total energy consumption
from the device ARM FW.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Include linux/bitfield.h only in habanalabs.h, instead of in each and
every file that needs it, as habanalabs.h is already included by all.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
change busy engines bitmask to 64 bits in order to represent
more engines, needed for future ASIC support.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Eliminate following warning:
warning: Shifting signed 32-bit value by 31 bits is undefined behavior
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The driver waits for the TPC vector pipe to be empty before checking if the
TPC kernel has finished executing, but the code doesn't validate that the
pipe was indeed empty, it just wait for it without checking the return
value.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
new_dma_pkt->ctl is assigned a value and then is reassigned a new value
without the first value ever being used.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use the standard FIELD_PREP() macro instead of << operator to perform
bitmask operations. This ensures type check safety and eliminate compiler
warnings.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use the standard macros to define bitmasks.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
If both parts of if-else are goto statements, we can remove the else and
put the else goto statement after the if statement.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
%u is used for unsigned so we need to cast the int variable to u32 to avoid
compiler warning.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Although the possible values for CB's ID are only 32 bits, there are a few
places in the code where this field is shifted and passed into a function
which expects 64 bits.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
If there is a failure during the testing of a queue,
to ease up debugging - print the queue id.
Signed-off-by: Dotan Barak <dbarak@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Allow user application to write to this register in order
to be able to configure the quiet period of the QMAN between grants.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
driver will now get notified upon any PCI error occurred and
will respond according to the severity of the error.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Although the driver defines the first user-available sync manager object
and monitor in habanalabs.h, we would like to also expose this information
via the INFO IOCTL so the runtime can get this information dynamically.
This is because in future ASICs we won't need to define it statically.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Update firmware header with new API for getting pcie info
such as tx/rx throughput and replay counter.
These counters are needed by customers for monitor and maintenance
of multiple devices.
Add new opcodes to the INFO ioctl to retrieve these counters.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
habanalabs driver uses dma-fence mechanism for synchronization.
dma-fence mechanism was designed solely for GPUs, hence we purpose
a simpler mechanism based on completions to replace current
dma-fence objects.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Future ASIC names are longer than 15 chars so increase the variable length
to 32 chars.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Slightly easier to read.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
PASID is defined as a few different types in iommu including "int",
"u32", and "unsigned int". To be consistent and to match with uapi
definitions, define PASID and its variations (e.g. max PASID) as "u32".
"u32" is also shorter and a little more explicit than "unsigned int".
No PASID type change in uapi although it defines PASID as __u64 in
some places.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/1600187413-163670-2-git-send-email-fenghua.yu@intel.com
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20200916170933.20302-4-vadym.kochan@plvision.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20200916170933.20302-3-vadym.kochan@plvision.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set type as NVMEM_TYPE_EEPROM to expose this info via
sysfs:
$ cat /sys/bus/nvmem/devices/{DEVICE}/type
EEPROM
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
v4:
split power down flow and power saving function to two patch
v5:
fix up modified change under the --- line
Add rts522a L1 sub-state support
Save more power on rts5227 rts5249 rts525a rts5260
Fix rts5260 driving parameter
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20200907100731.7722-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initializing sensors requires attaching to pd 2. Add an ioctl for that.
This corresponds to FASTRPC_INIT_ATTACH_SENSORS in the downstream driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200908131013.19630-4-jonathan@marek.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
