On DA830/OMAP-L137 and DA850/OMAP-L138 SoCs, the McASP peripheral
has FIFO support. This FIFO provides additional data buffering. It
also provides tolerance to variation in host/DMA controller response
times. More details of the FIFO operation can be found at
http://focus.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=sprufm1&fileType=pdf
Existing sequence of steps for audio playback/capture are:
a. DMA configuration
b. McASP configuration (configures and enables FIFO)
c. Start DMA
d. Start McASP (enables FIFO)
During McASP configuration, while FIFO was being configured, FIFO
was being enabled in davinci_hw_common_param() function of
sound/soc/davinci/davinci-mcasp.c file. This generated a transmit
DMA event, which gets serviced when DMA is started.
https://patchwork.kernel.org/patch/84611/ patch clears the DMA
events before starting DMA, which is the right thing to do. But
this resulted in a state where DMA was waiting for an event from
McASP (after step c above), but the event which was already there,
has got cleared (because of step b above).
The fix is not to enable the FIFO during McASP configuration as
FIFO was being enabled as part of McASP start.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The line-in input is 0x7 not 0x2 for MacBook (Pro) 5,1 / 5,2 models
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For RANGE requests, we should only query as much bytes as we're in fact
interested in.
For CUR requests, we shouldn't confuse the firmware with an overlong
request but just ask for 2 bytes.
This might need fixing in the future as it's not entirely clear when to
dispatch 1-byte, 2-byte and 4-byte request blocks. For now, we assume
everything is coded in 16bit - this works for all firmware
implementations I've seen.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A device may report its supported sample rates in ranges rather than in
discrete triplets. The code used to only parse the MIN field instead of
properly paying attention to the MAX and RES values.
Also, handle RES values of 1 correctly and announce a continous sample
rate range in this case.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Control messages directed to an interface must have the interface number
set in the lower 8 bits of wIndex. This wasn't done correctly for some
clock and mixer messages.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With multiple codec configurations, some codec might have no ADC, thus
it keeps spec->adc_nids = NULL. This causes an Oops in alc_build_controls().
Reference: kernel bug #16156https://bugzilla.kernel.org/show_bug.cgi?id=16156
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The '*bitclk' of structure 'snd_at73c213' seems no use,
so I make a patch to remove the unnecessary variable.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add's the iMac7,1 SSID entry to
patch_realtek.c which adds sound support.
bug entry:
https://bugs.launchpad.net/mactel-support/+bug/360866
Note:I do not have this machine on hand only
codec#0 file for the machine so please
test if you have the appropriate equipment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add's the MacBookAir1,1 SSID entry to
patch_realtek.c which adds sound support.
bug entry:
https://bugs.launchpad.net/mactel-support/+bug/268301
Note:I do not have this machine on hand only
codec#0 file for the machine so please
test if you have the appropriate equipment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds the SSID number to snd_pci_quirk for the
MacBookAir2,1 taken from codec#0 at:
http://launchpadlibrarian.net/49455483/Card0.Codecs.codec.0.txt
keep in mind I do not have one of these machines on hand
so please if you do have this machine please test for me..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda-intel - fix wallclk variable update and condition
ALSA: asihpi - Fix uninitialized variable
ALSA: hda: Use LPIB for ASUS M2V
usb/gadget: Replace the old USB audio FU definitions in f_audio.c
ASoC: MX31ads sound support should depend on MACH_MX31ADS_WM1133_EV1
ASoC: Add missing Kconfig entry for Phytec boards
ALSA: usb-audio: export UAC2 clock selectors as mixer controls
ALSA: usb-audio: clean up find_audio_control_unit()
ALSA: usb-audio: add UAC2 sepecific Feature Unit controls
ALSA: usb-audio: unify constants from specification
ALSA: usb-audio: parse clock topology of UAC2 devices
ALSA: usb-audio: fix selector unit string index accessor
include/linux/usb/audio-v2.h: add more UAC2 details
ALSA: usb-audio: support partially write-protected UAC2 controls
ALSA: usb-audio: UAC2: clean up parsing of bmaControls
ALSA: hda: Use LPIB for another mainboard
ALSA: hda: Use mb31 quirk for an iMac model
ALSA: hda: Use LPIB for an ASUS device
This patch fixes thinko introduced in "last minutes" before commiting
of the last wallclk patch.
It also fixes the condition checking if the first period after last
wallclk update is processed. There is a little rounding error in
period_wallclk.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Initialize prev_ctl properly before reference:
sound/pci/asihpi/asihpi.c: In function ‘snd_card_asihpi_mixer_new’:
sound/pci/asihpi/asihpi.c:2568:30: warning: ‘prev_ctl.dst_node_index’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BugLink: https://launchpad.net/bugs/587546
Symptom: On the reporter's ASUS M2V, using PulseAudio in Ubuntu 10.04 LTS
results in the PA daemon crashing shortly after attempting playback of an
audio file.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, attempt playback of an audio file while PulseAudio is
active.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: D Tangman
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC2 clock selectors are fortunately compatible with UAC1 audio
selector units, so we can simply reuse the same approach to get all the
linked units.
Requests to this control need a different CS value though.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a struct to parse the audio units, and return usable descriptors
for all types. There's no need to limit the result set, except for some
kind of sanity check.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bits to enable them are always 0 for UAC1 devices, so no additional
checks are required.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move more definitions from private enums to appropriate header files.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio devices which comply to the UAC2 standard can export complex clock
topologies in its descriptors and set up links between them.
The entities that are defined are
- clock sources, which define the end-leafs.
- clock selectors, which act as switch to select one out of many
possible clocks sources.
- clock multipliers, which have an input clock source, and act as clock
source again. They can be used to derive one clock from another.
All sample rate changes, clock validity queries and the like must go to
clock source elements, while clock selectors and multipliers can be used
as terminal clock source.
The following patch adds a parser for these elements and functions to
iterate over the tree and find the leaf nodes (clock sources).
The samplerate set functions were moved to the new clock.c file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, UAC2 controls are marked read-only if any of the channels are
marked read-only in the descriptors. Change this behaviour and
- mark them writeable unless all channels are read-only
- store the read-only mask in usb_mixer_elem_info and
- check the mask again in set_cur_mix_value(), and bail out for
write-protected channels.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce two new static inline functions for a more readable parsing
of UAC2 bmaControls.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/580749
Symptom: on the original reporter's VIA VT1708-based board, the
PulseAudio daemon dies shortly after the user attempts to play an audio
file.
Test case: boot from Ubuntu 10.04 LTS live cd; attempt to play an audio
file.
Resolution: add SSID for the original reporter's hardware to the
position_fix quirk table, explicitly specifying the LPIB method.
Reported-and-Tested-By: Harald
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/542550
Symptom: On the reporter's iMac, in Ubuntu 10.04 LTS neither playback
nor capture appear audible out-of-the-box.
Test case: Boot from an Ubuntu 10.04 LTS live cd or from an installed
configuration and attempt to play or capture audio.
Resolution: Specify the mb31 quirk for this machine in the codec SSID
table.
Reported-and-Tested-By: f3a97
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/465942
Symptom: On the reporter's ASUS device, using PulseAudio in Ubuntu 10.04
LTS results in the PA daemon crashing shortly after attempting to select
capture or to configure the audio hardware profile.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's capture volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Irihapeti
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
ALSA: snd-usb-caiaq: Bump version number to 1.3.21
ALSA: Revert "ALSA: snd-usb-caiaq: Set default input mode of A4DJ"
ALSA: snd-usb-caiaq: Simplify single case to an 'if'
ALSA: snd-usb-caiaq: Restore 'Control vinyl' input mode on A4DJ
ALSA: hda: Use LPIB for a Shuttle device
ALSA: hda: Add support for another Lenovo ThinkPad Edge in conexant codec
ALSA: hda: Use LPIB for Sony VPCS11V9E
ALSA: usb-audio: fix feature unit parser for UAC2
ALSA: asihpi - Minor code cleanup
ALSA: asihpi - Add support for new ASI8800 family
ALSA: asihpi - Fix bug preventing outstream_write preload from happening
ALSA: asihpi - Fix imbalanced lock path in hw_message
ALSA: asihpi - Remove support for old ASI8800 family
ALSA: asihpi - Add hd radio blend functions
ALSA: asihpi - Remove unused io map functions
ALSA: usb-audio: add support for UAC2 pitch control
ALSA: usb-audio: parse UAC2 endpoint descriptors correctly
ALSA: usb-audio: fix return values
ALSA: usb-audio: parse more format descriptors with structs
sound: Add missing spin_unlock
...
Do not explicity set the default input mode. Use the hardware default
of mode 0 ('Control vinyl'), which is now available.
This reverts commit e3ca4c9.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After removing code, only one case remains. So use an 'if' instead.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This feature was undocumented on early A4DJ units. It is indicated
by lighting both the 'line' and 'phono' lamps at the same time.
Newer units document this and the newer Windows drivers enable this
for all units, so restore the functionality.
This patch simplifies the code and changes the mode mapping to match
the A8DJ, favouring simpler code and consistency over keeping the
existing mapping.
Both 'Control vinyl' and 'Phono' input modes enable the hardware
preamp. The difference is the input impedance.
This reverts commit 9a9527e.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/551949
Symptom: On the reporter's Shuttle device, using PulseAudio in Ubuntu
10.04 LTS results in "popping clicking" audio with the PA crashing
shortly thereafter.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Christian Mehlis <mehlis@inf.fu-berlin.de>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a Thinkpad Edge 13 "01972NG" I had the problem that speakers played
sound although headphones were plugged in. Using model=ideapad with
latest alsa-git kernel fixed this. So adding this quirk to use ideapad
for another Thinkpad Edge variant seems sensible.
Cc: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/586347
Symptom: On the Sony VPCS11V9E, using GStreamer-based applications with
PulseAudio in Ubuntu 10.04 LTS results in stuttering audio. It appears
to worsen with increased I/O.
Test case: use Rhythmbox under increased I/O pressure. This symptom is
reproducible in the current daily stable alsa-driver snapshots (at least
up until 21 May 2010; later snapshots fail to build from source due to
missing preprocessor directives when compiled against 2.6.32).
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Lauri Kainulainen <lauri@sokkelo.net>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a small off-by-one bug which causes the feature unit to announce a
wrong number of channels. This leads to illegal requests sent to the
firmware eventually.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
