The pseries platform uses 32bit default DMA window (always 4K pages) and
optional 64bit DMA window available via DDW ("Dynamic DMA Windows"),
64K or 2M pages. For ages the default one was not removed and a huge
window was created in addition. Things changed with SRIOV-enabled
PowerVM which creates a default-and-bigger DMA window in 64bit space
(still using 4K pages) for IOV VFs so certain OSes do not need to use
the DDW API in order to utilize all available TCE budget.
Linux on the other hand removes the default window and creates a bigger
one (with more TCEs or/and a bigger page size - 64K/2M) in a bid to map
the entire RAM, and if the new window size is smaller than that - it
still uses this new bigger window. The result is that the default window
is removed but the "ibm,dma-window" property is not.
When kdump is invoked, the existing code tries reusing the existing 64bit
DMA window which location and parameters are stored in the device tree but
this fails as the new property does not make it to the kdump device tree
blob. So the code falls back to the default window which does not exist
anymore although the device tree says that it does. The result of that
is that PCI devices become unusable and cannot be used for kdumping.
This preserves the DMA64 and DIRECT64 properties in the device tree blob
for the crash kernel. Since the crash kernel setup is done after device
drivers are loaded and probed, the proper DMA config is stored at least
for boot time devices.
Because DDW window is optional and the code configures the default window
first, the existing code creates an IOMMU table descriptor for
the non-existing default DMA window. It is harmless for kdump as it does
not touch the actual window (only reads what is mapped and marks those IO
pages as used) but it is bad for kexec which clears it thinking it is
a smaller default window rather than a bigger DDW window.
This removes the "ibm,dma-window" property from the device tree after
a bigger window is created and the crash kernel setup picks it up.
Fixes: 381ceda88c ("powerpc/pseries/iommu: Make use of DDW for indirect mapping")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220629060614.1680476-1-aik@ozlabs.ru
During kdump, two set of NMI IPIs are sent to secondary CPUs, if
'crash_kexec_post_notifiers' option is set. The first set of NMI IPIs
to stop the CPUs and the other set to collect register data. Instead,
capture register data for secondary CPUs while stopping them itself.
Also, fallback to smp_send_stop() in case the function gets called
without kdump configured.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220630064942.192283-1-hbathini@linux.ibm.com
With GCC 12, corenet64_smp_defconfig leads to the following build errors:
CC arch/powerpc/kernel/irq.o
{standard input}: Assembler messages:
{standard input}:3616: Error: unrecognized opcode: `wrteei'
{standard input}:5689: Error: unrecognized opcode: `wrteei'
CC arch/powerpc/kernel/pmc.o
{standard input}: Assembler messages:
{standard input}:42: Error: unrecognized opcode: `mfpmr'
{standard input}:53: Error: unrecognized opcode: `mtpmr'
CC arch/powerpc/kernel/io.o
{standard input}: Assembler messages:
{standard input}:376: Error: unrecognized opcode: `mbar'
...
CC arch/powerpc/mm/nohash/book3e_hugetlbpage.o
{standard input}: Assembler messages:
{standard input}:291: Error: unrecognized opcode: `tlbsx'
{standard input}:482: Error: unrecognized opcode: `tlbwe'
{standard input}:608: Error: unrecognized opcode: `lbarx'
{standard input}:608: Error: unrecognized opcode: `stbcx.'
-mpcu=powerpc64 cannot be used anymore for book3e, it must be a booke CPU.
But then we get:
CC arch/powerpc/lib/xor_vmx.o
cc1: error: AltiVec not supported in this target
Altivec is not supported with -mcpu=e5500 so don't allow selection
of altivec when e5500 is selected.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/77255a5a957967723b84d0356d9e5fb21569f4e8.1657549153.git.christophe.leroy@csgroup.eu
Since commit 4bf4f42a2f ("powerpc/kbuild: Set default generic
machine type for 32-bit compile"), when building a 32 bits kernel
with a bi-arch version of GCC, or when building a book3s/32 kernel,
the option -mcpu=powerpc is passed to GCC at all time, relying on it
being eventually overriden by a subsequent -mcpu=xxxx.
But when building the same kernel with a 32 bits only version of GCC,
that is not done, relying on gcc being built with the expected default
CPU.
This logic has two problems. First, it is a bit fragile to rely on
whether the GCC version is bi-arch or not, because today we can have
bi-arch versions of GCC configured with a 32 bits default. Second,
there are some versions of GCC which don't support -mcpu=powerpc,
for instance for e500 SPE-only versions.
So, stop relying on this approximative logic and allow the user to
decide whether he/she wants to use the toolchain's default CPU or if
he/she wants to set one, and allow only possible CPUs based on the
selected target.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d4df724691351531bf46d685d654689e5dfa0d74.1657549153.git.christophe.leroy@csgroup.eu
Commit 0e00a8c9fd ("powerpc: Allow CPU selection also on PPC32")
enlarged the CPU selection logic to PPC32 by removing depend to
PPC64, and failed to restrict that depend to E5500_CPU and E6500_CPU.
Fortunately that got unnoticed because -mcpu=8540 will override the
-mcpu=e500mc64 or -mpcu=e6500 as they are ealier, but that's
fragile and may no be right in the future.
Add back the depend PPC64 on E5500_CPU and E6500_CPU.
Fixes: 0e00a8c9fd ("powerpc: Allow CPU selection also on PPC32")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/8abab4888da69ff78b73a56f64d9678a7bf684e9.1657549153.git.christophe.leroy@csgroup.eu
Currently the perf CPU backend drivers detect what CPU they're on using
cur_cpu_spec->oprofile_cpu_type.
Although that works, it's a bit crufty to be using oprofile related fields,
especially seeing as oprofile is more or less unused these days.
It also means perf is reliant on the fragile logic in setup_cpu_spec()
which detects when we're using a logical PVR and copies back the PMU
related fields from the raw CPU entry. So lets check the PVR directly.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[chleroy: Added power10 and fixed checkpatch issues]
Reviewed-and-tested-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-and-tested-By: Kajol Jain <kjain@linux.ibm.com> [For 24x7 side changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20c0ee7f99dbf0dbf8658df6b39f84753e6db1ef.1657204631.git.christophe.leroy@csgroup.eu
Since commit 4291d085b0 ("powerpc/32s: Make pte_update() non
atomic on 603 core"), pte_update() has been using
mmu_has_feature(MMU_FTR_HPTE_TABLE) to avoid a useless atomic
operation on 603 cores.
When kasan_early_init() sets up the early zero shadow, it uses
__set_pte_at(). On book3s/32, __set_pte_at() calls pte_update()
when CONFIG_SMP is selected in order to ensure the preservation of
_PAGE_HASHPTE in case of concurrent update of the PTE. But that's
too early for mmu_has_feature(), so when
CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG is selected, mmu_has_feature()
calls printk(). That's too early to call printk() because KASAN
early zero shadow page is not set up yet. It leads to a deadlock.
However, when kasan_early_init() is called, there is only one CPU
running and no risk of concurrent PTE update. So __set_pte_at() can
be called with the 'percpu' flag. With that flag set, the PTE is
written directly instead of being written via pte_update().
Fixes: 4291d085b0 ("powerpc/32s: Make pte_update() non atomic on 603 core")
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2ee707512b8b212b079b877f4ceb525a1606a3fb.1656655567.git.christophe.leroy@csgroup.eu
Always set an IBAT covering up to _einittext during init because when
CONFIG_MODULES is not selected there is no reason to have an exception
handler for kernel instruction TLB misses.
It implies DBAT and IBAT are now totaly independent, IBATs are set
by setibat() and DBAT by setbat().
This allows to revert commit 9bb162fa26 ("powerpc/603: Fix
boot failure with DEBUG_PAGEALLOC and KFENCE")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ce7f04a39593934d9b1ee68c69144ccd3d4da4a1.1655202804.git.christophe.leroy@csgroup.eu
mark_initmem_nx() calls either mmu_mark_initmem_nx() or
set_memory_attr() based on return from v_block_mapped()
of _sinittext.
But we can now handle text and data independently, so that
text may be mapped by block even when data is mapped by pages.
On the 8xx for instance, at startup 32Mbytes of memory are
pinned in TLB. So the pinned entries need to go away for sinittext.
In next patch a BAT will be set to also covers sinittext on book3s/32.
So it will also be needed to call mmu_mark_initmem_nx() even when
data above sinittext is not mapped with BATs.
As this is highly dependent on the platform, call mmu_mark_initmem_nx()
regardless of data block mapping. Then the platform will know what to
do.
Modify 8xx mmu_mark_initmem_nx() so that inittext mapping is modified
only when pagealloc debug and kfence are not active, otherwise inittext
is mapped with standard pages. And don't do anything on kernel text
which is already mapped with PAGE_KERNEL_TEXT.
Fixes: da1adea075 ("powerpc/8xx: Allow STRICT_KERNEL_RwX with pinned TLB")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/db3fc14f3bfa6215b0786ef58a6e2bc1e1f964d7.1655202804.git.christophe.leroy@csgroup.eu
cpu_to_node() is not yet available (setup_arch() is called before
setup_per_cpu_areas() by start_kernel()).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220711030653.150950-1-npiggin@gmail.com
Commit 6d8278c414 ("powerpc/64s/radix: do not flush TLB on spurious
fault") removed the TLB flush for spurious faults, except when a
coprocessor (nest MMU) maps the address space. This is not needed
because the NMMU workaround in the PTE permission upgrade paths
prevents PTEs existing with less restrictive access permissions than
their corresponding TLB entries have.
Remove it and replace with a comment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220525022358.780745-4-npiggin@gmail.com
The nest MMU in POWER9 does not re-fetch the PTE in response to
permission mismatch, contrary to the architecture[*] and unlike the core
MMU. This requires a TLB flush before upgrading permissions of valid
PTEs, for any address space with a coprocessor attached.
Per (non-public) Nest MMU Workbook, POWER10 nest MMU conforms to the
architecture in this regard, so skip the workaround.
[*] See: Power ISA Version 3.1B, 6.10.1.2 Modifying a Translation Table
Entry, Setting a Reference or Change Bit or Upgrading Access
Authority (PTE Subject to Atomic Hardware Updates):
"If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Reference or Change bit to
1 or to upgrade access authority, a simpler sequence suffices
because the translation hardware will refetch the PTE if an
access is attempted for which the only problems were reference
and/or change bits needing to be set or insufficient access
authority."
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220525022358.780745-3-npiggin@gmail.com
Per (non-public) Nest MMU Workbook, POWER10 and POWER9P NMMU does not
cache PTEs in PWC, so does not require PWC flush to invalidate these
translations.
Skip the workaround on POWER10 and later.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220525022358.780745-2-npiggin@gmail.com
Processors with coherent icache require the sequence sync ; icbi ; isync
to entire store->execute coherency. icbi (to any address) must be
executed to ensure isync flushes the pipeline. See "POWER9 Processor
User's Manual, 4.6.2.2 Instruction Cache Block Invalidate (icbi)" for
details.
__kernel_sync_dicache is missing icbi for the coherent icache path.
Add it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220520123649.258440-1-npiggin@gmail.com
By default on PPC32 PCI bus numbers are unique across all PCI domains.
So a system could have only 256 PCI buses independently of available PCI
domains.
This is due to filling DT property pci-OF-bus-map which does not support
a multi-domain setup.
On all powerpc platforms except chrp and powermac there is no DT
property pci-OF-bus-map anymore and therefore it is possible on
non-chrp/powermac platforms to avoid this limitation of maximum number
of 256 PCI buses in a system even on multi-domain setup.
But avoiding this limitation would mean that all PCI and PCIe devices
would be present on completely different BDF addresses as every PCI
domain starts numbering PCI bueses from zero (instead of the last bus
number of previous enumerated PCI domain). Such change could break
existing software which expects fixed PCI bus numbers.
So add a new config option CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT which
enables this change. By default it is disabled. It causes the initial
value of hose->first_busno to be zero.
Signed-off-by: Pali Rohár <pali@kernel.org>
[mpe: Minor change log wording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220706104308.5390-6-pali@kernel.org
Function pci_create_OF_bus_map() is used only in chrp code.
So hide it from all other platforms.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220706104308.5390-4-pali@kernel.org
Function pci_device_from_OF_node() is used only in powermac code. So
hide it from all other platforms.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220706104308.5390-2-pali@kernel.org
CPLD firmware can reset board by writing value 0x01 at CPLD memory offset
0x0d. Define syscon-reboot node for this reset support.
Fixes: 54c15ec3b7 ("powerpc: dts: Add DTS file for CZ.NIC Turris 1.x routers")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713134429.18748-1-pali@kernel.org
By default old pre-3.0 Freescale PCIe controllers reports invalid PCI Class
Code 0x0b20 for PCIe Root Port. It can be seen by lspci -b output on P2020
board which has this pre-3.0 controller:
$ lspci -bvnn
00:00.0 Power PC [0b20]: Freescale Semiconductor Inc P2020E [1957:0070] (rev 21)
!!! Invalid class 0b20 for header type 01
Capabilities: [4c] Express Root Port (Slot-), MSI 00
Fix this issue by programming correct PCI Class Code 0x0604 for PCIe Root
Port to the Freescale specific PCIe register 0x474.
With this change lspci -b output is:
$ lspci -bvnn
00:00.0 PCI bridge [0604]: Freescale Semiconductor Inc P2020E [1957:0070] (rev 21) (prog-if 00 [Normal decode])
Capabilities: [4c] Express Root Port (Slot-), MSI 00
Without any "Invalid class" error. So class code was properly reflected
into standard (read-only) PCI register 0x08.
Same fix is already implemented in U-Boot pcie_fsl.c driver in commit:
d18d06ac35
Fix activated by U-Boot stay active also after booting Linux kernel.
But boards which use older U-Boot version without that fix are affected and
still require this fix.
So implement this class code fix also in kernel fsl_pci.c driver.
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220706101043.4867-1-pali@kernel.org
The .incbin assembler directive is much faster than bin2c + $(CC).
Do similar refactoring as in commit 4c0f032d49 ("s390/purgatory:
Omit use of bin2c").
Please note the .quad directive matches to size_t in C (both 8 byte)
because the purgatory is compiled only for the 64-bit kernel.
(KEXEC_FILE depends on PPC64).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220725015619.618070-1-masahiroy@kernel.org
During an LPM, while the memory transfer is in progress on the arrival
side, some latencies are generated when accessing not yet transferred
pages on the arrival side. Thus, the NMI watchdog may be triggered too
frequently, which increases the risk to hit an NMI interrupt in a bad
place in the kernel, leading to a kernel panic.
Disabling the Hard Lockup Watchdog until the memory transfer could be a
too strong work around, some users would want this timeout to be
eventually triggered if the system is hanging even during an LPM.
Introduce a new sysctl variable nmi_watchdog_factor. It allows to apply
a factor to the NMI watchdog timeout during an LPM. Just before the CPUs
are stopped for the switchover sequence, the NMI watchdog timer is set
to watchdog_thresh + factor%
A value of 0 has no effect. The default value is 200, meaning that the
NMI watchdog is set to 30s during LPM (based on a 10s watchdog_thresh
value). Once the memory transfer is achieved, the factor is reset to 0.
Setting this value to a high number is like disabling the NMI watchdog
during an LPM.
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713154729.80789-5-ldufour@linux.ibm.com
Introduce a factor which would apply to the NMI watchdog timeout.
This factor is a percentage added to the watchdog_tresh value. The value is
set under the watchdog_mutex protection and lockup_detector_reconfigure()
is called to recompute wd_panic_timeout_tb.
Once the factor is set, it remains until it is set back to 0, which means
no impact.
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713154729.80789-4-ldufour@linux.ibm.com
In pseries_migration_partition(), loop until the memory transfer is
complete. This way the calling drmgr process will not exit earlier,
allowing callbacks to be run only once the migration is fully completed.
If reading the VASI state is done after the hypervisor has completed the
migration, the HCALL is returning H_PARAMETER. We can safely assume that
the memory transfer is achieved if this happens.
This will also allow to manage the NMI watchdog state in the next commits.
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713154729.80789-2-ldufour@linux.ibm.com
Since commit 87c78b612f ("powerpc: Fix all occurences of "the the"")
fixed "the the", there's now a steady stream of patches fixing other
duplicate words.
Just fix them all at once, to save the overhead of dealing with
individual patches for each case.
This leaves a few cases of "that that", which in some contexts is
correct.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220718095158.326606-1-mpe@ellerman.id.au
PAPR v2.12 defines a new hypercall, H_WATCHDOG. The hypercall permits
guest control of one or more virtual watchdog timers.
These timers do not conform to PowerPC device conventions. They are
not affixed to any extant bus, nor do they have full representation in
the device tree.
As a workaround we represent them as platform devices.
This patch registers a single platform device, "pseries-wdt", with the
platform bus if the FW_FEATURE_WATCHDOG flag is set.
A driver for this device, "pseries-wdt", will be introduced in a
subsequent patch.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713202335.1217647-4-cheloha@linux.ibm.com
PAPR v2.12 specifies a new optional function set, "hcall-watchdog",
for the /rtas/ibm,hypertas-functions property. The presence of this
function set indicates support for the H_WATCHDOG hypercall.
Check for this function set and, if present, set the new
FW_FEATURE_WATCHDOG flag.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713202335.1217647-3-cheloha@linux.ibm.com
PAPR v2.12 defines a new hypercall, H_WATCHDOG. The hypercall permits
guest control of one or more virtual watchdog timers.
Add the opcode for the H_WATCHDOG hypercall to hvcall.h. While here,
add a definition for H_NOOP, a possible return code for H_WATCHDOG.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713202335.1217647-2-cheloha@linux.ibm.com
With GCC 12 allmodconfig prom_init fails to build:
Error: External symbol 'memset' referenced from prom_init.c
make[2]: *** [arch/powerpc/kernel/Makefile:204: arch/powerpc/kernel/prom_init_check] Error 1
The allmodconfig build enables KASAN, so all calls to memset in
prom_init should be converted to __memset by the #ifdefs in
asm/string.h, because prom_init must use the non-KASAN instrumented
versions.
The build failure happens because there's a call to memset that hasn't
been caught by the pre-processor and converted to __memset. Typically
that's because it's a memset generated by the compiler itself, and that
is the case here.
With GCC 12, allmodconfig enables CONFIG_INIT_STACK_ALL_PATTERN, which
causes the compiler to emit memset calls to initialise on-stack
variables with a pattern.
Because prom_init is non-user-facing boot-time only code, as a
workaround just disable stack variable initialisation to unbreak the
build.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220718134418.354114-1-mpe@ellerman.id.au
Returning an error code (here -EBUSY) from a remove callback doesn't
prevent the driver from being unloaded. The only effect is that an error
message is emitted and the driver is removed anyhow.
So instead drop the remove function (which is equivalent to returning zero)
and set the suppress_bind_attrs property to make it impossible to unload
the driver via sysfs.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220612213400.159257-1-u.kleine-koenig@pengutronix.de
Add caps support under "/sys/bus/event_source/devices/<pmu>/"
for powerpc. This directory can be used to expose some of the
specific features that powerpc PMU supports to the user.
Example: pmu_name. The name of PMU registered will depend on
platform, say power9 or power10 or it could be Generic Compat
PMU.
Currently the only way to know which is the registered
PMU is from the dmesg logs. But clearing the dmesg will make it
difficult to know exact PMU backend used. And even extracting
from dmesg will be complicated, as we need to parse the dmesg
logs and add filters for pmu name. Whereas by exposing it via
caps will make it easy as we just need to directly read it from
the sysfs.
Add a caps directory to /sys/bus/event_source/devices/cpu/
for power8, power9, power10 and generic compat PMU in respective
PMU driver code. Update the pmu_name file under caps folder
in core-book3s using "attr_update".
The information exposed currently:
- pmu_name : Underlying PMU name from the driver
Example result with power9 pmu:
# ls /sys/bus/event_source/devices/cpu/caps
pmu_name
# cat /sys/bus/event_source/devices/cpu/caps/pmu_name
POWER9
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220520084630.15181-1-atrajeev@linux.vnet.ibm.com
When booting on a machine that uses the compat pmu driver we see this:
[ 0.071192] GENERIC_COMPAT performance monitor hardware support registered
Which is a bit shouty. Give it a nicer name.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220610044006.2095806-1-joel@jms.id.au
Merge our fixes branch. In particular this brings in commit
9864816180 ("powerpc/book3e: Fix PUD allocation size in
map_kernel_page()") which fixes a build failure in next, because commit
2db2008e63 ("powerpc/64e: Rewrite p4d_populate() as a static inline
function") depends on it.
The platform device for the rng must be created much later in boot.
Otherwise it tries to connect to a parent that doesn't yet exist,
resulting in this splat:
[ 0.000478] kobject: '(null)' ((____ptrval____)): is not initialized, yet kobject_get() is being called.
[ 0.002925] [c000000002a0fb30] [c00000000073b0bc] kobject_get+0x8c/0x100 (unreliable)
[ 0.003071] [c000000002a0fba0] [c00000000087e464] device_add+0xf4/0xb00
[ 0.003194] [c000000002a0fc80] [c000000000a7f6e4] of_device_add+0x64/0x80
[ 0.003321] [c000000002a0fcb0] [c000000000a800d0] of_platform_device_create_pdata+0xd0/0x1b0
[ 0.003476] [c000000002a0fd00] [c00000000201fa44] pnv_get_random_long_early+0x240/0x2e4
[ 0.003623] [c000000002a0fe20] [c000000002060c38] random_init+0xc0/0x214
This patch fixes the issue by doing the platform device creation inside
of machine_subsys_initcall.
Fixes: f3eac42665 ("powerpc/powernv: wire up rng during setup_arch")
Cc: stable@vger.kernel.org
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
[mpe: Change "of node" to "platform device" in change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220630121654.1939181-1-Jason@zx2c4.com
With commit ffa0b64e3b ("powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit")
the kernel now validate the addr against high_memory value. This results
in the below BUG_ON with dax pfns.
[ 635.798741][T26531] kernel BUG at mm/page_alloc.c:5521!
1:mon> e
cpu 0x1: Vector: 700 (Program Check) at [c000000007287630]
pc: c00000000055ed48: free_pages.part.0+0x48/0x110
lr: c00000000053ca70: tlb_finish_mmu+0x80/0xd0
sp: c0000000072878d0
msr: 800000000282b033
current = 0xc00000000afabe00
paca = 0xc00000037ffff300 irqmask: 0x03 irq_happened: 0x05
pid = 26531, comm = 50-landscape-sy
kernel BUG at :5521!
Linux version 5.19.0-rc3-14659-g4ec05be7c2e1 (kvaneesh@ltc-boston8) (gcc (Ubuntu 9.4.0-1ubuntu1~20.04.1) 9.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #625 SMP Thu Jun 23 00:35:43 CDT 2022
1:mon> t
[link register ] c00000000053ca70 tlb_finish_mmu+0x80/0xd0
[c0000000072878d0] c00000000053ca54 tlb_finish_mmu+0x64/0xd0 (unreliable)
[c000000007287900] c000000000539424 exit_mmap+0xe4/0x2a0
[c0000000072879e0] c00000000019fc1c mmput+0xcc/0x210
[c000000007287a20] c000000000629230 begin_new_exec+0x5e0/0xf40
[c000000007287ae0] c00000000070b3cc load_elf_binary+0x3ac/0x1e00
[c000000007287c10] c000000000627af0 bprm_execve+0x3b0/0xaf0
[c000000007287cd0] c000000000628414 do_execveat_common.isra.0+0x1e4/0x310
[c000000007287d80] c00000000062858c sys_execve+0x4c/0x60
[c000000007287db0] c00000000002c1b0 system_call_exception+0x160/0x2c0
[c000000007287e10] c00000000000c53c system_call_common+0xec/0x250
The fix is to make sure we update high_memory on memory hotplug.
This is similar to what x86 does in commit 3072e413e3 ("mm/memory_hotplug: introduce add_pages")
Fixes: ffa0b64e3b ("powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220629050925.31447-1-aneesh.kumar@linux.ibm.com
Trying to build a .c file that includes <linux/bpf_perf_event.h>:
$ cat test_bpf_headers.c
#include <linux/bpf_perf_event.h>
throws the below error:
/usr/include/linux/bpf_perf_event.h:14:28: error: field ‘regs’ has incomplete type
14 | bpf_user_pt_regs_t regs;
| ^~~~
This is because we typedef bpf_user_pt_regs_t to 'struct user_pt_regs'
in arch/powerpc/include/uaps/asm/bpf_perf_event.h, but 'struct
user_pt_regs' is not exposed to userspace.
Powerpc has both pt_regs and user_pt_regs structures. However, unlike
arm64 and s390, we expose user_pt_regs to userspace as just 'pt_regs'.
As such, we should typedef bpf_user_pt_regs_t to 'struct pt_regs' for
userspace.
Within the kernel though, we want to typedef bpf_user_pt_regs_t to
'struct user_pt_regs'.
Remove arch/powerpc/include/uapi/asm/bpf_perf_event.h so that the
uapi/asm-generic version of the header is exposed to userspace.
Introduce arch/powerpc/include/asm/bpf_perf_event.h so that we can
typedef bpf_user_pt_regs_t to 'struct user_pt_regs' for use within the
kernel.
Note that this was not showing up with the bpf selftest build since
tools/include/uapi/asm/bpf_perf_event.h didn't include the powerpc
variant.
Fixes: a6460b03f9 ("powerpc/bpf: Fix broken uapi for BPF_PROG_TYPE_PERF_EVENT")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Use typical naming for header include guard]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627191119.142867-1-naveen.n.rao@linux.vnet.ibm.com
The convention for indentation seems to be a single tab. Help text is
further indented by an additional two whitespaces. Fix the lines that
violate these rules.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220520115431.147593-1-juergh@canonical.com
