Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has separate filter masks for compressed/uncompressed
BlockAcks and BlockAckRequests. Add them.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c"
changed the behavior of INI overriding which is needed only
for PCI cards. Revert to the original check.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.
Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rx and tx dumps go through the tracing infrastructure,
we no longer need to keep these routines around.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a few tracepoints to ath5k driver transmit and
receive callbacks in order to record packet traffic.
We record the entire packet in the trace buffer so that
the data can be extracted with trace-cmd and external
plugins.
Compared to the previous debugging calls, this approach
removes an out-of-line function call from the tx and rx
paths in the compiled-in-but-disabled case, while
improving the ability to process the logged data.
A new option, CONFIG_ATH5K_TRACER, is added so that one
may disable the tracepoints completely.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_WEP_NKID is not used in ath9k any more since the key handling code
has been moved to ath/.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables 4.9GHz frequencies in ath5k if they are allowed as indicated by
the regulatory domain code. Currently this is MKK9_MKKC (0xfe).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a helper function to ath/regd.c which can be asked if 4.9GHz channels
are allowed for a given regulatory domain code. This keeps the knowledge of
regdomains and defines like MKK9_MKKC in one place. I'm passing the regdomain
code instead of the ath_regulatory structure because this needs to be called
quite early in the driver inititalization where ath_regulatory is not available
yet in ath5k.
I'm using MKK9_MKKC only because this is the regdomain in the 802.11j enabled
sample cards we got from our vendor. I found some hints in HAL code that this
is used by Atheros to indicate 4.9GHz channels support and that there might be
other domain codes as well, but as I don't have any documentation I'm just
putting in what I need right now. It can be extended later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shorten some lines and make code more readable.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.
ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.
One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.
Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.
By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.
Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211 will properly assign sequence numbers to QoS-data
frames but cannot do so correctly for non-QoS-data and
management frames because beacons need them from that counter
as well and mac80211 cannot guarantee proper sequencing."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch syncs up the header files with
the project's main firmware carl9170fw.git.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused macros and cleanup buffer_type enumeration
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove useless test_bit - it's not going to happen because of the way this
function is called only when that bit is set.
And fix some whitespace.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to read and backup AR_WA register value permanently and reading
this after the chip is awakened results in this register being zeroed out.
This seems to fix the ASPM with L1 enabled issue that we have observed.
The laptop becomes very slow and hangs mostly with ASPM L1 enabled without
this fix.
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks
Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.
fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The auto-arp feature sometimes has unexpected side effects (e.g. firmware
crashes, no ARP replies, etc.)
disable it until it will be solved.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The passive scan channel dwell time currently used is 30-60TU. A typical
beacon interval for AP's is 100TU. This leads to a ~30% worst-case probability
of finding an AP via passive scanning.
For 5GHz bands for DFS frequencies passive scanning is the only scanning
option. Hence for these, the probability of finding an AP is very low.
To fix this, increase the passive channel scan dwell times (also the early
leave value, as 5GHz channels are still typically very silent.) Use a value
of 100TU, because that covers most typical AP configurations.
Based on testing the probability of finding an AP (100TU beacon interval) on
a single scan round are as follows (based on 100 iterations):
dwell min/max (TU) | probability
---------------------+------------
30/60 | 35%
60/60 | 56%
80/80 | 77%
100/100 | 100%
Total scan times now and after the change:
Region | Before (s) | After (s)
-------+------------+----------
00 | 0.77 | 1.48
FI | 0.95 | 2.01
US | 0.91 | 1.76
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Return values were assigned to incorrect var / weren't assigned.
fix it, and defer mutex_lock after the sanity checks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add new ampdu_action ops to support receiver BA.
The BA initiator session management in FW independently.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add 80211n BA initiator session support wl1271 driver.
Include BA supported FW version auto detection mechanism.
BA initiator session management included in FW independently.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Channel 14 is only supported in Japan (JP country code in regdb). The
FW limits tranmissions to CCK only on this channel.
Tested in both STA and AP modes to work correctly.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In wl12xx cards AP-mode requires a separate FW file. Add this file to
the module info.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
PLT mode start/stop is controlled from userspace. When removing module, the
PLT mode state is however not checked, and not cleared. There is the possibility
of some unwanted state to left linger and there is even the possiblity of a
kernel crash if for instance IRQ work is running when the module is removed.
Fix this by stopping PLT mode on module removal, if still running.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx chips do the AMDPU aggregation work in the firmware, but it
supports a maximum of 8 frames per block. Configure the mac80211 hw
structure accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
changed the visibility of the debug_level module parameter
in the filesystem to be readable and writable to the root user.
It is now accessible under /sys/module/wl12xx/parameters
removed the debug_level debugfs file that was created under
/sys/kernel/debug/...
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were calling ieee80211_find_sta() and the sta returned by it
without locking the RCU, which is required by mac80211.
Fix this and reorganize slightly the area of the code where the sta is
used.
Reported-by: Jonathan DE CESCO <jonathanc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When 11a is not supported, we were modifying the global structure that
contains the bands supported by the driver. This causes problems when
having more one wl12xx device in the same system because they all use
the same global. This also causes problems when the wl12xx_sdio
module is removed and the wl12xx module remains.
Fix this problem by copying the band structure into the wl12xx
instance.
Reported-by: Arik Nemtsov <arik@wizery.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx "rejoins" upon every BSS_CHANGED_BSSID notification.
However, there is no need to rejoin after disassociation, so just
filter out the case when the new bssid is 00:00:00:00:00:00.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Indicate support for the NL80211_IFTYPE_AP interface mode to enable AP
mode operation.
Disable 11a when operating in AP-mode (unsupported for now).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Try to read the MAC address from the on-disk NVS file.
A non-zero MAC address is required to add an AP interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
AP and STA modes use different firmwares.
Differentiate the firmware files by name and fetch the appropriate one
when add_interface is called by mac80211. The STA firmware is chosen for
PLT mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Encryption key configuration is different for AP/STA modes.
AP encryption keys are recorded when the BSS is not started. On BSS
start they are propagated to the AP (in wl1271_ap_init_hwenc).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Record TX configuration settings in the "conf" member of our global
structure (struct wl1271) if conf_tx is called when the firmware is
not loaded.
Later on when the firmware is loaded, we apply the tx conf as part of
the init sequence.
Important for AP mode since conf_tx is called before add_interface
(where the firmware is initialized).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When in AP mode set appropriate HLID and rate policy for each skb.
Respond to supported-rates related changes in op_tx only when acting
as STA.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allocate and free host link IDs (HLIDs) for each link. A per-STA
data structure keeps the HLID of each STA.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Do not configure a group address table in AP mode
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate configuration according to mode. AP has different rate
set configuration and no handling of idle-state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
