To enable gro_flush_timeout, a driver has to use napi_complete_done()
instead of napi_complete().
Tested:
Ran 200 netperf TCP_STREAM from A to B (10Gbe mlx4 link, 8 RX queues)
Without this feature, we send back about 305,000 ACK per second.
GRO aggregation ratio is low (811/305 = 2.65 segments per GRO packet)
Setting a timer of 2000 nsec is enough to increase GRO packet sizes
and reduce number of ACK packets. (811/19.2 = 42)
Receiver performs less calls to upper stacks, less wakes up.
This also reduces cpu usage on the sender, as it receives less ACK
packets.
Note that reducing number of wakes up increases cpu efficiency, but can
decrease QPS, as applications wont have the chance to warmup cpu caches
doing a partial read of RPC requests/answers if they fit in one skb.
B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average: eth0 811269.80 305732.30 1199462.57 19705.72 0.00
0.00 0.50
B:~# echo 2000 >/sys/class/net/eth0/gro_flush_timeout
B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average: eth0 811577.30 19230.80 1199916.51 1239.80 0.00
0.00 0.50
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 3cc81d85ee ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olivier having laid the groundwork this patch transmits the
multicast flag to the device to save some bus traffic.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings. One is fixed by casting return
value to a return type of the function. The others by creating a specific
stmmac_platform.h which provides the bits related to the platform driver.
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: warning: incorrect type in return expression (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: expected void *
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: got void [noderef] <asn:2>*reg
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:64:29: warning: symbol 'meson6_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:354:29: warning: symbol 'stih4xx_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:361:29: warning: symbol 'stid127_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c:133:29: warning: symbol 'sun7i_gmac_data' was not declared. Should it be static?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a kernel helper to dump buffers in a hexdecimal format. This patch
substitutes the open coded function by calling that helper.
The output is slightly changed:
- no lead space
- ASCII part will be printed along with the dump
- offset is longer than 3 characters (now 8)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of skb_copy_datagram_const_iovec in
favour of the iovec iterator-based skb_copy_datagram_iter.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of skb_copy_datagram_const_iovec in
favour of the iovec iterator-based skb_copy_datagram_iter.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-06
Please pull this batch of fixes intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
For the iwlwifi bits, Emmanuel says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition to vxlan nla_policy for UDP checksum. This is necessary
to enable UDP checksums on VXLAN.
In some instances, enabling UDP checksums can improve performance on
receive for devices that return legacy checksum-unnecessary for UDP/IP.
Also, UDP checksum provides some protection against VNI corruption.
Testing:
Ran 200 instances of TCP_STREAM and TCP_RR on bnx2x.
TCP_STREAM
IPv4, without UDP checksums
14.41% TX CPU utilization
25.71% RX CPU utilization
9083.4 Mbps
IPv4, with UDP checksums
13.99% TX CPU utilization
13.40% RX CPU utilization
9095.65 Mbps
TCP_RR
IPv4, without UDP checksums
94.08% TX CPU utilization
156/248/462 90/95/99% latencies
1.12743e+06 tps
IPv4, with UDP checksums
94.43% TX CPU utilization
158/250/462 90/95/99% latencies
1.13345e+06 tps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb allocation fails during receive processing, the driver would
continue reading descriptors without first determining if there were
any more descriptors for the current packet. Update the code to check
whether more descriptors are associated with the current packet or
whether to move on to the next descriptor as a new packet.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channel structure is freed before freeing the per channel
interrupts resulting in a kernel oops. Move the call to free
the channel structure to after the freeing of the per channel
interrupts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vnet_event_napi() may be called as part of the NAPI ->poll,
to resume reading descriptor rings. When no data is available,
descriptor ring state (e.g., rcv_nxt) needs to be reset
carefully to stay in lock-step with ldc_read(). In the interest
of simplicity, the best way to do this is to return from
vnet_event_napi() when there are no more packets to read.
The next trip through ldc_rx will correctly set up the dring state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: David Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant tab.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PIDs are only used in the id table, so the definitions are
unnacessary. Remove them wouldn't have confusion.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace using VID/PID with using tp->version to initialize the ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move r8152b_get_version() to the location before rtl_ops_init().
Then, the rtl_ops_init() could use tp->version.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 is very similar to the mv88e6171. So extend the
mv88e6171 driver to support it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b9 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also add dummy functions where required to avoid NULL pointer dereference.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch in preparation for the upcoming EF10 sriov support.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series provides a base and cleanup for the
upcoming EF10 SRIOV support.
This patch moves the VF state into siena_nic_data as a basis to
save the VF state based on nic type.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditionally pulling 128 bytes into the linear area is not required
for:
- security: Every protocol demux starts with pskb_may_pull() to pull
frag data into the linear area, if necessary, before looking at
headers.
- performance: Netback has already grant copied up-to 128 bytes from
the first slot of a packet into the linear area. The first slot
normally contain all the IPv4/IPv6 and TCP/UDP headers.
The unconditional pull would often copy frag data unnecessarily. This
is a performance problem when running on a version of Xen where grant
unmap avoids TLB flushes for pages which are not accessed. TLB
flushes can now be avoided for > 99% of unmaps (it was 0% before).
Grant unmap TLB flush avoidance will be available in a future version
of Xen (probably 4.6).
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pr_* macros let's use dev_* macros which provide device name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate pci driver to managed resources to reduce boilerplate error handling
code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert system PM callbacks to use dev_pm_ops. In addition remove the PCI calls
related to a power state since the bus code cares about this already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last standard PCI resource is defined as PCI_STD_RESOURCE_END. Thus, we
could use it instead of plain integer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings.
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:381:30: warning: symbol 'enh_desc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:253:30: warning: symbol 'ndesc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:141:33: warning: symbol 'stmmac_ptp' was not declared. Should it be static?
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ieee802154/at86rf230.c:1365:1-3: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe-phy driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to sync the states of the PCS and the PHY
after a reset is performed. If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the spelling of the word "descriptor" in a couple
of locations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool receive side scaling (RSS) commands.
Support is added to get/set the RSS hash key and the RSS lookup table.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for receive side scaling (RSS). RSS allows
for spreading incoming network packets across the Rx queues. When used
in conjunction with the per DMA channel interrupt support, this allows
the receive processing to be spread across multiple processors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for interrupts that are generated by the
Tx/Rx DMA channel pairs of the device. This allows for Tx and Rx
processing to run across multiple processsors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide support for splitting IP packets so that the header and
payload can be sent to different DMA addresses. This will allow
the IP header to be put into the linear part of the skb while the
payload can be added as frags.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use page allocations for Rx buffers instead of pre-allocating skbs
of a set size.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx and Rx descriptors are unsigned 32 bit values. Use the u32
type, rather than unsigned int, to map these descriptors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pre_xmit function name implies that it performs operations prior
to transmitting the packet when in fact it is responsible for setting
up the descriptors and initiating the transmit. Rename this to
function from pre_xmit to dev_xmit, which is consistent with the name
used during receive processing - dev_read.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the channel and ring tracking structures allocation to device
open. This will allow for future support to vary the number of Tx/Rx
queues without unloading the module.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.
Prior this patch, the stmmac_eee_init could be called in several places
as shown below:
stmmac_open stmmac_resume PHY Layer
| | |
stmmac_hw_setup stmmac_adjust_link
| | stmmac ethtool
|__________________________|______________|
|
stmmac_eee_init
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing spin_unlock when tx frames gets dropped.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.
This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a very old and often unused option to configure
a bit in a register inside the DMA. This support should
not stay under Koption and should be extended for new chips too.
This will be do later maybe via device-tree parameters.
Also no performance impact when remove this setting on STi platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the STMMAC_DEBUG_FS Koption is now removed from the
driver configuration and this support will be built
by default when DEBUG_FS is present. This can also be
useful on building driver verification.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all the Koptions added to build the glue-logic files
for all different architectures: DWMAC_MESON, DWMAC_SUNXI, DWMAC_STI ...
Nowadays the stmmac needs to be compiled on several platforms; in some
case it very convenient to guarantee that its build is always completed
with success on all the branches where the driver is present.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microblaze is a fpga soft core, it can be customized easily, which may
cause many various hardware version strings.
So the original fix patch based on hard-coded compatible version strings
is not a good idea (although it is correct for current issue). For it,
there will be a new solving way soon (which based on the device tree).
The original issue is related with qemu, so can only change the hardware
version string in qemu for it, then keep the original driver no touch (
qemu is for virtualization which has much easier life than real world).
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a force setting of slotted operation bit. The atben
chips sometimes set these bit. The reason is unknown. Nevertheless we
don't support slotted operation so we set this bit now force while
probing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for a random generated perm extended address for
the at86rf230 driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an ieee802154_vif similar like the ieee80211_vif which
holds the interface type and maybe further more attributes like the
ieee80211_vif structure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a sysfs binary file is asked to be removed, it is found by
attribute name, so strictly speaking this change is not a fix, but
just in case when attribute name is changed in the driver or sysfs
internals are changed, it might be better to remove the previously
created file using right the same binary attribute.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following kernel crash during SGMII based 1GbE probe.
BUG: Bad page state in process swapper/0 pfn:40fe6ad
page:ffffffbee37a75d8 count:-1 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: nonzero _count
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0+ #7
Call trace:
[<ffffffc000087fa0>] dump_backtrace+0x0/0x12c
[<ffffffc0000880dc>] show_stack+0x10/0x1c
[<ffffffc0004d981c>] dump_stack+0x74/0xc4
[<ffffffc00012fe70>] bad_page+0xd8/0x128
[<ffffffc000133000>] get_page_from_freelist+0x4b8/0x640
[<ffffffc000133260>] __alloc_pages_nodemask+0xd8/0x834
[<ffffffc0004194f8>] __netdev_alloc_frag+0x124/0x1b8
[<ffffffc00041bfdc>] __netdev_alloc_skb+0x90/0x10c
[<ffffffc00039ff30>] xgene_enet_refill_bufpool+0x11c/0x280
[<ffffffc0003a11a4>] xgene_enet_process_ring+0x168/0x340
[<ffffffc0003a1498>] xgene_enet_napi+0x1c/0x50
[<ffffffc00042b454>] net_rx_action+0xc8/0x18c
[<ffffffc0000b0880>] __do_softirq+0x114/0x24c
[<ffffffc0000b0c34>] irq_exit+0x94/0xc8
[<ffffffc0000e68a0>] __handle_domain_irq+0x8c/0xf4
[<ffffffc000081288>] gic_handle_irq+0x30/0x7c
This was due to hardware resource sharing conflict with the firmware. This
patch fixes this crash by using resources (descriptor ring, prefetch buffer)
that are not shared.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support when used with older firmware (<= 1.13.28).
- Added xgene_ring_mgr_init() to check whether ring manager is initialized
- Calling xgene_ring_mgr_init() from xgene_port_ops.reset()
- To handle errors, changed the return type of xgene_port_ops.reset()
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel.
-----BEGIN PGP SIGNATURE-----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=8uwd
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3v6b
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware was crashing when we were trying to warm reset it
after suspend. This was due to the fact that target registeres
can be accessed only if the hardware is awaken.
This patch makes sure to awake the device also on the hif up,
not only in case of probe call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing implementation of reset_resume handler just calls
ath6kl_usb_remove() that deallocates all resources.
It can lead to double free, etc. on disconnect.
The patch removes reset_resume handler,
so usb core could conservatively reset the driver.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-11-03
This series contains updates to i40e and i40evf.
Akeem adds a check for i40e so that flow director flush and reinit are
not done when flow director is not enabled.
Mitch fixes the i40evf driver to properly handle multiple admin queue
messages, by reinit the msg_size field each time we go through the loop.
Without this, we may receive truncated messages due to the firmware
thinking we have insufficient buffer size. Also fixes the link checking
logic to only check the carrier state if the interface is actually
open, which allows link changes to be reported correctly without spamming
the VFs. Updates i40e to inset the VSI ID in the QTX_CTL register
when configuring queues for VMDq VSIs.
Paul adds support for 10G-base-T in i40evf.
Jesse fixes i40e where the call to irq_dynamic_disable() was turning off
the interrupt completely when trying to set ITR to 0 (for lowest
moderation).
Shannon removes debugfs dump stats function, since it was not being
kept up-to-date and was redundant with the ethtool output. Also, scales
back the LAN MSIx usage to force queue/vector sharing and leave some
vectors for Flow Director, VMDq, etc. when there are more cores than
vectors available to the PF. Cleans up the error reporting for
get_lump() resource tracking errors. Also adds a check for the
debug module parameter earlier to be able to catch the early configuration
phase admin queue messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is check for dev is unnecessary, as we are already checking dev
after allocating it via alloc_netdev, and jumping to label: out
if it is NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4 ("macvtap: restore vlan header on user read")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data. However, this
has been broken ever since we added GSO meta-data. VLAN acceleration
also has the same problem.
This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.
The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN acceleration is in use on the xmit path, we end up
setting csum_start to the wrong place. The result is that the
whoever ends up doing the checksum setting will corrupt the packet
instead of writing the checksum to the expected location, usually
this means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN acceleration
is detected.
Fixes: 6680ec68ef ("tuntap: hardware vlan tx support")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to issue CONFIG_DEV "get" firmware command.
This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.
The GET operation is allowed for VFs too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed in order to get cache cold pages (L3 flushed) for HW scatter.
Otherwise memory may flush those entries when the packet comes from
PCI, causing back pressure resulting in BW decrease.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP_ALIGN has a non zero value, hardware will write to a non aligned
address. The only reader from this address is when copying the header
from the first frag into the linear buffer (further access to the IP
address will be from the linear buffer, in which the headers are
aligned). Since the penalty of non align access by the hardware is
greater than the software memcpy, changing the frag_align to always be 0.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect set_port_type() for concurrency, as the sysfs code could
call it from mutliple contexts in parallel.
The port_mutex is not enough because we need to protect from concurrent
modification of 'info' and stopping of the port sensing work.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added wrapper to the ACCESS_REG command for handling guest HW
registers access, preventing write operations, but do allow reads.
This will prevent SRIOV guests to change port PTYS configuration,
such as speed/advertised link modes.
Fixes: adbc7ac5c1 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a few problems with our parsing of the MDET registers:
* Queue IDs are longer than 8 bits
* Queue IDs are absolute for the device and the base queue must be
subtracted out.
* VF IDs are longer than 8 bits
* Use the MASK define to mask the event value, instead of the SHIFT
define.
Change-ID: I3dc7237f480c02e1192a2a8ea782f8a02ab2a8b7
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We must insert the VSI ID in the QTX_CTL register when
configuring queues for VMDQ VSIs.
Change-ID: Iedfe36bd42ca0adc90a7cc2b7cf04795a98f4761
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check the debug module parameter earlier to be able to catch the early
configuration phase adminq messages.
Change-ID: Ic84fabd72393489bbf96042de770790a80fd8468
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tweak and homogenize the error reporting for get_lump() resource
tracking errors.
Change-ID: I11330161cc6ad8d04371c499c63071c816171c3b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are more cores than vectors available to the PF, scale back
the LAN msix usage to force queue/vector sharing and leave some vectors
for Flow Director, VMDq, etc.
Change-ID: Ie0317732eb85ad8d851d7da7d9af86b1bf8c21ad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugfs dump stats wasn't being kept up-to-date, was redundant with
the ethtool output, and didn't offer any useful additional info. Rather
than continue trying to keep them aligned, just remove the debugfs command.
Change-ID: Id130ed9aef01c6369ab662c7b4c5ec5b1dbc5b40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <Jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to irq_dynamic_disable was turning off the interrupt completely
when trying to set ITR to 0 (for lowest moderation). Just remove the
call as setting the values to 0 later in this function will suffice.
Change-ID: I47caf1ecbe65653cf63ec833db93094cd83fd84d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add 10G-Base-T support in i40evf.
Change-ID: I98a1c3138d7d6572fe7903a7c1c4692cae3260d5
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.
Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.
Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.
Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When FD_SB/ATR are not enabled, do not allow flow director flush
and reinit.
Change-ID: Iafe261c1862992981615815551abd1ed9fada0a8
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the reset state channels accoridng at86rf2xx datasheets.
We don't need to set the default page here which is zero on all chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit e37d2ec82a ("mac802154: ops:
declare channel and page as u8") the page parameter can't be below zero.
This patch fix a kbuild test robot warning. Furthermore this check
should be removed and handled by netlink 802.15.4 interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:
yum install libvirt
yum install tunctl
tunctl -b
ip link set tap0 up
brctl addif virbr0 tap0
./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
-kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
-no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
-net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
-net tap,vlan=0,ifname=tap0,script=no,downscript=no
in microblaze qemu bash (guest machine):
ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
ifconfig eth0 up
After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-10-31
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_print_status() to report a change in the PHY status.
The current message is not verbose enough, so this commit improves
it by using the generic status message.
After this change, the kernel reports PHY status down and up events as:
mvneta f1070000.ethernet eth0: Link is Down
mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Because bonding stats are usually sum of slave stats, it was
not easy to account for tx drops at bonding layer.
We can use dev->tx_dropped for this, as this counter is later
added to the device stats (in dev_get_stats())
This extends the idea we had in commit ee63771474 ("bonding: Simplify
the xmit function for modes that use xmit_hash") for bond_3ad_xor_xmit()
to other bonding modes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add cfg80211 dump_survey handler for mwifiex.
This handler will be called to report channel statistics
to cfg80211.
This in turn adds ACS support for mwifiex AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to record channel statistics during
scan. With extended scan, scan results are returned as events from
FW while channel statistics are part of scan command response.
We store these channel statistics in adapter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting old radio via HWSIM_CMD_DEL_RADIO then listeners on the
multicast group "config" are informed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding new radio via HWSIM_CMD_NEW_RADIO then listeners on the
multicast group "config" are informed.
While at it, refactor the configuration parameters to be able to
pass them directly and have fewer function arguments.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few recent additions to the netlink attributes neglected
to add policy entries, fix that now.
Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee07e ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44c5 ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.
Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.
Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now it was possible to simulate soft and
hard fw crashes but it wasn't possible to trigger
an immediately hw restart itself (without the fw
crash).
This can be useful when stress testing hw
restarting stability, e.g. during heavy tx/rx
traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While testing other things I've found that CE
items aren't cleared properly. This could lead to
null dereferences in BMI.
To prevent that make sure CE revoking clears the
nbytes value (which is used as a buffer completion
indication) and memset the entire CE ring data
shared between host and target when
(re)initializing.
Also make sure to check BMI xfer pointer and print
a splat instead of crashing the kernel.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently hif_power_up performs effectively a
reset and hif_stop resets the chip as well so
there's no point in resetting here.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power up procedure was overly complex due to
warm/cold reset workarounds and issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the problems with warm reset I've found is
that it must be guaranteed that copy engine
registers are not being accessed while being
reset. Otherwise in worst case scenario the host
may lock up.
Instead of using sleeps and hoping the device is
operational in some arbitrary timeframes use
firmware indication register.
As a side effect this makes driver
boot/stop/recovery faster.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make ath10k_pci_init_pipes() effectively only
alter shared target-host data.
The per_transfer_context is a host-only thing.
It is necessary to preserve it's contents for a
more robust ring cleanup.
This is required for future warm reset fixes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does not allow fragmentation by routers, so there is no
fragmentation ID in the fixed header. UFO for IPv6 requires the ID to
be passed separately, but there is no provision for this in the virtio
net protocol.
Until recently our software implementation of UFO/IPv6 generated a new
ID, but this was a bug. Now we will use ID=0 for any UFO/IPv6 packet
passed through a tap, which is even worse.
Unfortunately there is no distinction between UFO/IPv4 and v6
features, so disable UFO on taps and virtio_net completely until we
have a proper solution.
We cannot depend on VM managers respecting the tap feature flags, so
keep accepting UFO packets but log a warning the first time we do
this.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
Use multple Tx netdev queues for sunvnet by supporting a one-to-one
mapping between vnet_port and Tx queue. Provide a ndo_select_queue
indirection (vnet_select_queue()) which selects the queue based
on the peer that would be selected in vnet_start_xmit()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vnet_event_napi re-enables interrupts, it should
reset LDC_EVENT_DATA_READY as an optimization.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a906 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-30
This series contains updates to e1000, igb and ixgbe.
Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.
Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.
Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.
Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RTL8152_UNPLUG when finding -ENODEV. This could accelerate
unloading the driver when the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
win0_lock was being used un-initialized, resulting in warning traces
being seen when lock debugging is enabled (and just wrong)
Fixes : fc5ab02096 ('cxgb4: Replaced the backdoor mechanism to access the HW
memory with PCIe Window method')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_msix_fp_int() and bnx2x_interrupt() run from hard interrupt
context.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_rx_irq() and mlx4_en_tx_irq() run from hard interrupt context.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the workload spreading via vRSS for IPv6.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.
Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild test robot reports that there are extra semicolons in this
driver. All of them are caused by using "};" rather than "}" at the
end of a switch statement. This patch does not change any functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 statistics obtained from the device can be retrieved
dumping the 'macstat' file in debugfs folder.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 core statistics are retrieved from the core registers
but not stored. So the debug code was never triggered to give a
warning message on tx underruns or rx overflows. This patch fixes
this and assures the statistics are stored in the snapshot.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the inline function instead of directly indexing the array.
This allows some architectures with hardware instructions
for bit reversals to eliminate the array.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible to configure driver using mtu_max module parameter
by setting it to value in range of 68..7920 inclusive.
This is sub-optimal performance-wise in case packet is larger than 1 page.
mtu_max default value is 2228.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of FW error, make it clear (in dmesg) what branch is taken
in the error recovery code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnect flow may be invoked either from upper layer request,
or from event reported by the firmware.
In case of firmware event, driver need to release resources for the station but
not send another disconnect WMI command.
In case of upper layer request, WMI_DISCONNECT_STA_CMDID command need to
be issued for the firmware to perform disconnect on the MAC layer. Eventually,
event is expected to confirm MAC disconnect, but it is better to not wait for
firmware event and release station resources immediately. FW may fail to
report disconnect for various reasons, so one could not rely on event always reported.
Introduce parameter to distinguish 2 cases above to prevent double WMI command
issuing.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As communicated with the firmware & hardware teams
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When interface is down, recovery flow should not be attempted.
Next ndo_open() will trigger target reset, that is FW recovery.
Doing recovery while interface is down cause internal "up", leaving
internal driver state in conflict with network stack. Then, when network
stack will call ndo_open(), kernel oops will be triggered.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
prec_enq is a sdio specific function. Move it to sdio.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename sdio_host.h to sdio.h and dhd_sdio.c to sdio.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename sdio_host.h to sdio.h and dhd_sdio.c to sdio.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__brcmf_err is a tracepoint specific function. Move it to
tracepoint.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packet filters got configured but never used.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing the firmware error codes up the driver may be mapped to
linux error numbers which may impact proper fault analysis. So
better pass up a generic failure code, ie. -EBADE and only show
firmware error code in FIL debug message.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The define EBRCMF_UNSUPPORTED is not used in the source file so this
patch removes it.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Showing the firmware error allows to quickly give a clue what
went wrong and directly look in the firmware code that gave us
back the error.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds wowl support for SDIO bus devices. This feature
requires FW which has support for wowl built in.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds wowl support for USB bus devices. This feature
requires FW which has support for wowl built in.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce pulse_rssi threshold to 15 in order to improve radar pattern detection
probability on ext channel
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
firmware to wake up the platform when a specific network
is detected. Along with that I have fixes for d3 operation.
The usual amount of rate scaling stuff - we now support STBC.
The other commit that stands out is Johannes's work on
devcoredump. He basically starts to use the standard
infrastructure he built.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GpBe
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-john-2014-10-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Emmanuel Grumbach <egrumbach@gmail.com> says:
"The big new thing here is netdetect which allows the
firmware to wake up the platform when a specific network
is detected. Along with that I have fixes for d3 operation.
The usual amount of rate scaling stuff - we now support STBC.
The other commit that stands out is Johannes's work on
devcoredump. He basically starts to use the standard
infrastructure he built."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error in the code makes the allocated space for firmware to be too
small.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new version of rtlwifi needs code in rtl92ce_get_desc() that returns
the buffer address for read operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new version of rtlwifi needs code in rtl92se_get_desc() that returns
the buffer address for read operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtlwifi has been modified to call ieee80211_register_hw()
from the probe routine; however, the existing call in the callback
routine for deferred firmware loading was not removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes in checking for Bluetooth status added some callbacks to code
in rtlwifi. To make certain that all callbacks are defined, a dummy routine has been
added to rtlwifi, and the drivers that need to use it are modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During 11n RX reordering, if there is a hole in RX table,
driver will not send packets to kernel until the rxreorder
timer expires or the table is full.
However, currently driver always restarts rxreorder timer when
receiving a packet, which causes the timer hardly to expire.
So while connected with to 11n AP in a busy environment,
ping packets may get blocked for about 30 seconds.
This patch fixes this timer restarting by ensuring rxreorder timer
would only be restarted either timer is not set or start_win
has changed.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Plus Chen <pchen@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The right shift operation has higher precedence than the mask so we
left shift by "(i * 3)" and then immediately right shift by "(i * 3)"
then we mask. It should be left shift, mask, and then right shift.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Display sw_in_discards, sw_in_filtered, and sw_out_filtered for chips
supported by mv88e6123_61_65 and mv88e6352 drivers.
The variables are provided in port registers, not the normal status registers.
Mark by adding 0x100 to the register offset and add special handling code
to mv88e6xxx_get_ethtool_stats.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6123_61_65 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6352 supports read and write access to its configuration eeprom.
There is no means to detect if an EEPROM is connected to the switch.
Also, the switch supports EEPROMs with different sizes, but can not detect
or report the type or size of connected EEPROMs. Therefore, do not implement
the get_eeprom_len callback but depend on platform or devicetree data to
provide information about EEPROM presence and size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6123 and compatible chips support reading the chip temperature
from PHY register 6:26.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6352 supports reading the chip temperature from two PHY registers,
6:26 and 6:27. Report it using the more accurate register 6:27.
Also report temperature limit and alarm.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6176 is mostly compatible to MV88E6352 and is documented
in the same functional specification. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report known silicon revisions when probing Marvell 88E6131 switches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report known silicon revisions when probing Marvell 88E6060 switches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commands:
modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020
can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.
This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Incoming packet is dropped silently by sk_filter(), if the skb was
allocated from pfmemalloc reserves and the corresponding socket is
not marked with the SOCK_MEMALLOC flag.
Igb driver allocates pages for DMA with __skb_alloc_page(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, igb can get pages with pfmemalloc flag set.
If an incoming packet hits the pfmemalloc page and is large enough
(small packets are copying into the memory, allocated with
netdev_alloc_skb_ip_align(), so they are not affected), it will be
dropped.
This behavior is ok under high memory pressure, but the problem is
that the igb driver reuses these mapped pages. So, packets are still
dropping even if all memory issues are gone and there is a plenty
of free memory.
In my case, some TCP sessions hang on a small percentage (< 0.1%)
of machines days after OOMs.
Fix this by avoiding reuse of such pages.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Tested-by: Aaron Brown "aaron.f.brown@intel.com"
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VMWare's e1000 implementation does not seem to support unicast filtering.
This can be observed by configuring a macvlan interface on eth0 in a VM in
VMWare Fusion 5.0.5, and trying to use that interface instead of eth0.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch indicates that the at86rf230 driver deliver with checksum
instead drop the crc before delivering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for promiscuous mode setting for the at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Overdue introduction for address filtering hardware flag. Furthermore we
will check and set address filtering on interface up. This patch
prepares that we can check if an transceiver supports address filtering
option. Currently all mainline driver supports hardware address filtering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new IEEE802154_HW_ARET hardware flag for indicating
that the transceiver supports ARET handling. Also remove the
IEEE802154_HW_FRAME_RETRIES from IEEE802154_HW_CSMA flag. Frame retries
handling is part of ARET.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag is unnecessary, it came from some old code.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the interrupt handler still calls napi_complete. Although it
won't schedule NAPI again as either NAPI_STATE_DISABLE or
NAPI_STATE_SCHED is set, it is just unnecessary, and it makes more
sense to do this way.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tx_underun with tx_underrun for checkpatch.pl.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several warnings and errors of coding style rules corrected.
Compile tested.
Signed-off-by: Roberto Medina <robertoxmed@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced repetive Device ID's which got added in commit b961f9a488
("cxgb4vf: Remove superfluous "idx" parameter of CH_DEVICE() macro")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can automatically generate pause frames when the number
of free buffers drops under a certain threshold, but in order to do this,
the address of the last free buffer needs to be written to a specific
register for each RX queue.
This has to be done in 'gfar_clean_rx_ring' which is called for each
RX queue. In order not to impact performance, by adding a register write
for each incoming packet, this operation is done only when the PAUSE frame
transmission is enabled.
Whenever the link is readjusted, this capability is turned on or off.
Signed-off-by: Matei Pavaluca <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local flow control options needed in order to resolve the negotiation
are incorrectly calculated.
Previously 'mii_advertise_flowctrl' was called to determine the local advertising
options, but these were determined based on FLOW_CTRL_RX/TX flags which are
never set through ethtool.
The patch simply translates from ethtool flow options to mii flow options.
Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy device supports 802.3x flow control, but the specific flags are not set
in the phy initialisation code. Flow control flags need to be added to the
supported capabilities of the phydev by the driver.
This is needed in order for ethtool to work ('ethtool -A' code checks for these
flags)
Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lets hostapd start if you have SGI-20 configured
as one of your HT capabilities.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add frequency attribute when sending to user-space over
netlink socket. The frequency is currently ignored when
receiving from user-space.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the name HWSIM_CMD_NEW_RADIO and HWSIM_CMD_DEL_RADIO is more
fitting on how other pieces of the wireless system work.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scan reference wasn't released in case of offloaded scan,
causing the refcount to go wrong and prevent the device
from going into d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
STBC is enabled on HT/VHT SISO rates in case we don't care
about power consumption and it won't hurt BT.
This is done only in case the peer and our chip support STBC
of course.
While at it fixed a bug which was causing bw and ldpc
flags to be set incorrectly in the rate scale table in case
we are switching to a legacy Tx column. This had no real impact.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan condition iterator assumes that an interface is associated if
phy_ctxt is assigned, but this isn't the sutuation in P2P device.
OTOH P2P device is never associated so we can simply ignore it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi features a debug mechanism that allows to dump
binary data which is helpful to debug the firmware.
Until now, this data was made available for the userspace
through debugfs. For this exact purpose, devcoredump was
created. Move to the new infrastructure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These chips support STBC in both Tx and Rx.
Given that we've added STBC Tx support enable it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mvm->cur_ucode wasn't set before we actually load the
firmware. This caused issues when we boot in RFKILL since
we get an RFKILL interrupt upon boot even before we load
any firmware.
This leads to issues since iwl_mvm_set_hw_rfkill_state
(the RFKILL interrupts handler in mvm) relies on this
variable.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We used to need to include some headers in order to read the registers
and do all the calculations by ourselves, but this is not done anymore
(i.e. we let the firmware do this for us), so we don't need to include
those headers anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For WMM-AC we may have to be changing QoS parameters while the
queues are being flushed. This is not relevant in the "drop"
case, but matters when we wait for the device to finish the
transmissions.
To allow this, do the actual waiting without holding the mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The warning gives no information about the frame, and presents
the flags so that one might think they're the frame. Clarify
and add more information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is unused and won't be available in some future invocations of the
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The MVM_FW_BCAST_FILTER_PASS_ALL option defined in iwl-dbg-cfg.ini
configuration file allows to enable/disable FW broadcast filtering.
If MVM_FW_BCAST_FILTER_PASS_ALL is not defined in iwl-dbg-cfg.ini or
its value is 0, the mvm broadcast filtering is enabled.
Setting MVM_FW_BCAST_FILTER_PASS_ALL=1 in iwl-dbg-cfg.ini blocks sending
of BCAST_FILTER_CMD to FW.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the new format the "CSS section" has the same TLV type
as the "mem section". So we need to run the secured flow
for all the 8000 products.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the ARC is reset when we exit from Sx in case we had
WoWLAN running, we can't access the prph before we reset
the NIC.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few slave bus devices show better performance when we
reduce the size of the Tx A-MPDU.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Getting the BSS station vif is something that may be needed by other
parts of the code. So, instead of having an iterator specifically for
d3, change it into a generic one in utils.c. Additionally, add a
iwl_mvm_get_bss_vif() function to make it easier to retrieving it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Before we get all the chain (ie. mac80211, cfg80211, nl80211 and
userspace) changed to support net-detect, we can use this debugfs
entry for easy testing and as a proof of concept.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan. Spin a new function
off of the sched_scan_start op code for reuse. Additionally,
restructure the function a bit for more readability.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking if we are associated when suspending with wowlan
enabled in the interface iterator, allow it to return an unassociated
vif and move the check to the main suspend function. This will be
needed by netdetect, since it should also work when we are not
associated but the vif is active.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take the WoWLAN handling code out of the main suspend function,
dividing it into three parts: get_config (which is used before the
firmware is switched), switch_to_d3 (which handles the rebooting of
the hardware with the D3 firmware) and config (which configures the D3
firmware for WoWLAN operation). This is necessary to prepare for the
net-detect implementation, which will use only the switch_to_d3 part
of this flow.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mac80211 will never call rate_control_tx_status with a NULL
pointer for sta. Remove the superfluous check. This check
misled smatch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current TLC isn't optimized for low latency and some devices
have issues with MIMO. This kind of combo creates latency issues.
Allow to temporarily disable MIMO for tests in order to solve
the latency issues without the added complexity of MIMO.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch removes all might_sleep calls from driver layer. This
handling is already done by mac802154 layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The range of channel and page fits into an unsigned byte range. This
patch changes the set_channel parameter definitions for channel and
page to u8.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ieee802154_ops structure should be never changed during runtime.
This patch declare this structure as const to avoid a runtime change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Promiscuous mode was not supported anymore with my Lenovo adapters
(RTL8153) since commit c472ab68ad
(cdc-ether: clean packet filter upon probe).
It was not possible to use them in a bridge anymore.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the set_rx_mode callback.
Also move a comment about multicast filtering in this new function.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To delegate promiscuous mode and multicast filtering to the subdriver.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware requires the number of rings in indirection table to be a power
of 2. When setting number of channels to a non power of 2 number,
indirection table is using only the closest power of 2 rings.
Report this number in 'ethtool -x' and not the total number of rx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon failures, destroy_netdev is called, and spinlocks/works must be
initialized before calling it. Otherwise kernel panic may occur.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is instead of calling the actual implementation of
napi_synchronize, for better encapsulation.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang flagged the following. All are actually cosmetic cleanups, not really bugs:
drivers/net/ethernet/mellanox/mlx4/en_main.c:233:3: warning: Value stored to 'err' is never read
err = -ENOMEM;
^ ~~~~~~~
drivers/net/ethernet/mellanox/mlx4/en_main.c:293:3: warning: Value stored to 'err' is never read
err = -ENOMEM;
drivers/net/ethernet/mellanox/mlx4/en_netdev.c:648:16: warning: Assigned value is garbage or undefined
entry->reg_id = reg_id;
^ ~~~~~~
drivers/net/ethernet/mellanox/mlx4/en_netdev.c:659:2: warning: Function call argument is an uninitialized value
mlx4_en_uc_steer_release(priv, priv->dev->dev_addr, *qpn, reg_id);
(NOTE: reg_id is only used in the device-managed flow steering path, in which is it always initialized.
This is not a bug. Cleanup here is therefore cosmetic only).
drivers/net/ethernet/mellanox/mlx4/en_rx.c:122:3: warning: Value stored to 'frag_info' is never read
frag_info = &priv->frag_info[i];
^ ~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mlx4_en_reset_config to en_netdev.c as it now serves more general purpose.
Add support for turning OFF/ON the rx/tx vlan offlad.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mlx4_en_timestamp_config to mlx4_en_reset_config and extend it to support
choosing RX vlan offload configuration.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Support to set speed or advertised link modes via ethtool:
ethtool -s <ifname> [speed <speed>] [advertise <link modes>]
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- If dev cap MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL is ON, query PTYS register to fill ethtool settings.
else use default values.
- Use autoneg port cap and dev backplane autoneg cap to reprort autoneg interface capbilities.
- Fix typo in mlx4_en_port_state struct field (transciver to transceiver).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added 100M, 20G and 56G ethtool speed reporting support.
Update mlx4_en_test_speed self test with the new speeds.
Defined new link speeds in include/uapi/linux/ethtool.h:
+#define SPEED_20000 20000
+#define SPEED_40000 40000
+#define SPEED_56000 56000
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for get_module_info/get_module_eeprom ethtool support for cable info reading.
Added new cable types enum in include/uapi/linux/ethtool.h for ethtool use.
+#define ETH_MODULE_SFF_8636 0x3
+#define ETH_MODULE_SFF_8636_LEN 256
+#define ETH_MODULE_SFF_8436 0x4
+#define ETH_MODULE_SFF_8436_LEN 256
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new MAD_IFC command to read cable module info with attribute id (0xFF60).
Update include/linux/mlx4/device.h with function declaration (mlx4_get_module_info)
and the needed defines/enums for future use.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sysport_resume() was missing an UniMAC reset which can lead to
various receive FIFO corruptions coming out of a suspend cycle. If the
RX FIFO is stuck, it will deliver corrupted/duplicate packets towards
the host CPU interface.
This could be reproduced on crowded network and when Wake-on-LAN is
enabled for this particular interface because the switch still forwards
packets towards the host CPU interface (SYSTEMPORT), and we had to leave
the UniMAC RX enable bit on to allow matching MagicPackets.
Once we re-enter the resume function, there is a small window during
which the UniMAC receive is still enabled, and we start queueing
packets, but the RDMA and RBUF engines are not ready, which leads to
having packets stuck in the UniMAC RX FIFO, ultimately delivered towards
the host CPU as corrupted.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.
A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.
Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().
Fixes: b02e6d9ba7 ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell phy 88E1145 configuration & initialization was missing a case
for initializing SGMII mode. This patch adds that case.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-10-28
Please pull this batch of fixes intended for the 3.18 stream!
For the mac80211 bits, Johannes says:
"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
For the iwlwifi bits, Emmanuel says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
In addition...
Felix Fietkau adds a couple of ath code fixes related to regulatory
rule enforcement.
Hauke Mehrtens fixes a build break with bcma when CONFIG_OF_ADDRESS
is not set.
Karsten Wiese provides a trio of minor fixes for rtl8192cu.
Kees Cook prevents a potential information leak in rtlwifi.
Larry Finger also brings a trio of minor fixes for rtlwifi.
Rafał Miłecki adds a device ID to the bcma bus driver.
Rickard Strandqvist offers some strn* -> strl* changes in brcmfmac
to eliminate non-terminated string issues.
Sujith Manoharan avoids some ath9k stalls by enabling HW queue control
only for MCC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6171 can support two different tagging protocols, DSA and
EDSA. The switch driver structure only allows one protocol to be
enumerated, and DSA was chosen. However the Kconfig entry ensures the
EDSA tagging code is built. With a minimal configuration, we then end
up with a mismatch. The probe is successful, EDSA tagging is used, but
the switch is configured for DSA, resulting in mangled packets.
Change the switch driver structure to enumerate EDSA, fixing the
mismatch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 42f2725394 ("net: DSA: Marvell mv88e6171 switch driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional code to m88e1145_config_init function to allow the driver to
support SGMII mode.
Signed-off-by: Viet Nga Dao <vndao@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling DCBx in firmware automatically enables DCBx for control via host
lldp agents. Wait for an explicit setstate call from an lldp agents to enable
DCBx instead.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out any DCB apps we might have added to kernel table when we lose DCB
sync (or IEEE equivalent event). These were previously left behind and not
cleaned up correctly. IEEE allows individual components to work independently,
so improve check for IEEE completion by specifying individual components.
Fixes: 10b0046685 ("cxgb4: IEEE fixes for DCBx state machine")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices have multiple bands enables in the EEPROM data, even though
they are only calibrated for one. Allow platform data to disable
unsupported bands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some devices (especially little-endian ones), the flash EEPROM data
has a different endian, which needs to be detected.
Add a flag to the platform data to allow overriding that behavior
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the initial NF calibration less likely to fail.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can cause inconsistent calibration results or in some cases turn the
radio deaf.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When NF calibration fails, the radio often becomes deaf. The usual
hardware hang checks do not detect this, so it's better to issue a reset
when that happens.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "goto chip_reset" is a bit misleading, because it does not actually
issue a chip reset. Instead it is bypassing processing of other
interrupts and assumes that the tasklet will issue a chip reset.
In the case of RXORN this does not happen, so bypassing processing of
other interrupts will simply allow them to fire again. Even if RXORN
was triggering a reset, it is not critical enough to need the bypass
here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
UB124 is a USB based reference design not supported by ath9k or
ath9k_htc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals use up quite a bit of space, and PC-OEM support is
typically not needed on embedded systems
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix a 11b/EVM issue by adjusting
FIR filter coefficients.
* Fix a problem with receiving probe request
frames sent at 11b rate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes RX sensitivity issues with AR9580.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently has a race which can be hit
with this sequence:
* Start a scan operation.
* TX BA is initiated by ieee80211_start_tx_ba_session().
* Driver sets up internal state and calls
ieee80211_start_tx_ba_cb_irqsafe().
* mac80211 adds a packet to sdata->skb_queue with
type IEEE80211_SDATA_QUEUE_AGG_START.
* ieee80211_iface_work() doesn't process the
packet because scan is in progress.
* ADDBA response timer expires and the sta/tid is
torn down.
* Driver receives BA stop notification and calls
ieee80211_stop_tx_ba_cb_irqsafe().
* This is also added to the queue by mac80211.
* Now, scan finishes.
At this point, the queued up packets might be processed
if some other operation schedules the sdata work. Since
the tids have been cleaned up already, warnings are hit.
If this doesn't happen, the packets are left in the queue
until the interface is torn down.
Since initiating a BA session when scan is in progress
leads to flaky connections, especially in MCC mode, we
can drop the TX BA request. This improves connectivity
with legacy clients in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flush timeout in MCC mode is very small, since
we are constrained by the time slice for each
channel context, but since only the HW queues are
flushed when switching contexts, it is acceptable.
Since the SW queues are also emptied in the mac80211 flush()
callback, a larger duration is needed. Add an override
argument to __ath9k_flush() and set it when flush()
is called in MCC mode. This allows the driver to
drain both the SW and HW queues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using ATH_CHANCTX_EVENT_ASSIGN to abort
a HW scan when a new interface becomes active, use the
mgd_prepare_tx() callback. This allows us to make
sure that the GO's channel becomes operational by
using flush_work().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that a GO interface
sends out a new NoA schedule with 200ms duration
when mgd_prepare_tx() is called.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has to be notified when a RoC period
expires in the driver. In MCC mode, since the
offchannel/RoC timer is set with the requested
duration, ieee80211_remain_on_channel_expired() needs
to be called when the timer expires.
But, currently it is done after we move back to
the operating channel. This is incorrect - fix this
by calling ieee80211_remain_on_channel_expired() when
the RoC timer expires and in ath_roc_complete() when
the RoC request is aborted.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a GO interface is active when we receive a
mgd_prepare_tx() call, then we need to send
out a new NoA before switching to a new context.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since both the arguments need to satisfy
the alignment requirements of ether_addr_copy(),
use memcpy() in cases where there will be no
big performance benefit and make sure that
ether_addr_copy() calls use properly aligned
arguments.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ATH_CHANCTX_EVENT_AUTHORIZED is required to trigger
the MCC scheduler when a station interface becomes
authorized. But, since the driver gets station state
notifications when the current operating mode is AP
too, make sure that we send ATH_CHANCTX_EVENT_AUTHORIZED
only when the interface is in station mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pending frames in the driver can be present
either in the HW queues or SW. ath9k_has_pending_frames()
currently checks for the HW queues first and then
checks if any ACs are queued in the driver.
In MCC mode, we need to check the HW queues alone, since
the SW queues are just marked as 'stopped' - they will
be processed in the next context switch. But since we
don't differentiate this now, mention whether we want
to check if there are frames in the SW queues.
* The flush() callback checks both HW and SW queues.
* The tx_frames_pending() callback does the same.
* The call to __ath9k_flush() in MCC mode checks HW queues alone.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An offchannel operation also needs to have
a flush timeout that doesn't exceed the NoA
absence duration of a GO context, so use
channel_switch_time. The first offchannel
operation is set a flush timeout of 10ms since
channel_switch_time will be zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, the duration for a channel context
is half the beacon interval and having a large
flush timeout will adversely affect GO operation,
since the default value of 200ms will overshoot
the advertised NoA absence duration.
The scheduler initiates a channel context switch
only when the slot duration for the current
context expires, so there is no possibility of
having a fixed timeout for flush.
Since the channel_switch_time is added to the
absence duration when the GO sets up the NoA
attribute, this is the maximum time that we
have to flush the TX queues. The duration is very
small, but we don't have a choice in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timeout value for flushing the TX queues
is hardcoded at 200ms right now. Use a channel
context-specific value instead to allow adjustments
to the timeout in case MCC is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an active context transitions to inactive
state, the NoA schedule needs to be removed
for the context that has beaconing enabled.
Not doing this will affect p2p clients.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a chip reset is done, all running timers,
tasklets etc. are stopped but the beacon tasklet
is left running. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a HW reset is done, the interrupt tasklet is
disabled before ISRs are disabled in the HW. This
allows a small window where the HW can still generate
interrupts. Since the tasklet is disabled and not killed,
it is not scheduled but deferred for execution at a later
time.
This happens because ATH_OP_HW_RESET is not set when ath_reset()
is called. When the hw_reset_work workqueue is used, this
problem doesn't arise because ATH_OP_HW_RESET is set
and the ISR bails out.
Set ATH_OP_HW_RESET properly in ath_reset() to avoid
this race - all the ath_reset_internal() callers have
been converted to use ath_reset() in the previous patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having ath_reset_internal() and ath_reset()
as two separate calls to perform a HW reset, have
one function. This makes sure that the behavior will
be the same at all callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the current operating channel context has
been marked as ATH_CHANCTX_STATE_FORCE_ACTIVE,
do not process beacons that might be received,
since we have to wait for the station to become
authorized.
Also, since the cached TSF value will be zero
initially do not rearm the timer in this
case when a beacon is received, since it results
in spurious values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, currently the decision to enable
the multi-channel state machine is done
based on the association status if one of
the interfaces assigned to a context is in
station mode.
This allows the driver to switch to the other
context before the current station is able to
complete the 4-way handshake in case it is
required and this causes problems.
Instead, enable multi-channel mode when the
station moves to the authorized state. This
disallows an early switch to the other channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the sta_add()/sta_remove() callbacks,
use the sta_state() callback since this gives
more fine-grained control.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not overwrite AR_PHY_RADAR_1 most significant byte default value
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original condition was "(PAGE_SIZE - len)" when "(len < PAGE_SIZE)"
is intended.
This condition is not really sufficient, but also not really needed...
If "len > PAGE_SIZE" then it we will print a warning message in dmesg
but there are no other effects. Maybe we should just remove the
condition?
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ->ibss_dfs pointer is always allocated with a user controlled
length. This caused a static checker warning because what if the length
was zero? In that case, any dereference of ->ibss_dfs would lead to an
Oops.
It turns out that this isn't a problem because the ->ibss_dfs pointer is
never used. This patch deletes it along with all the related code. In
particular the entire libipw_network_reset() function can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We provide timeout value to rt2x00usb_vendor_request_buff() based on
number of registers to process. That value is passed down to
rt2x00usb_vendor_req_buff_lock() and ends in usb_control_msg(). But we
do not read/write all registers in rt2x00usb_vendor_req_buff_lock() at
once. We read/write them in chunks of 64 bytes in the loop, hence passed
timeout value to low level is too big.
Patch removes timeout argument from rt2x00usb_vendor_request_buff() and
use short REGISTER_TIMEOUT in rt2x00usb_vendor_req_buff_lock(). That
timeout value should be fine for 64 bytes and smaller requests. For
EEPROM read we introduced new timeout value equal to 2 seconds.
Patch fixes process uninterruptible sleep stalls for long period, when
USB bus has problem to satisfy a request and we wait very long time on
usb_start_wait_urb().
Reported-and-tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iZLf
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current behaviour it to copy the frame inclusive CRC into a skb, then
remove the CRC from the skb. This patch optimizes this by not copying
the CRC at the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the ieee802154_is_valid_psdu_len function to validate
the psdu length. If the psdu length is invalid we use the maximum
payload to receive also corrupted frames in monitor mode.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the allocation of skb inside the ieee802154 driver
layer to dev_alloc_skb. This changes also the gfp mask to GFP_ATOMIC
which is needed for upcomming change that the receiving is done by a
tasklet and not a workqueue anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Good for automated testing, where user can create wlan
interfaces with specified names.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, it can be very difficult to know which is which
if you are trying to do detailed testing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After moving the EQ ownership to software effectively destroying it, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying the EQ, the object responsible for generating interrupts, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer. This patch solves a very
rare case when we get panic on driver unload.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A full Rx ring only requires 1 MiB of memory. This is not enough
memory that it is useful to dynamically scale the number of Rx
requests in the ring based on traffic rates, because:
a) Even the full 1 MiB is a tiny fraction of a typically modern Linux
VM (for example, the AWS micro instance still has 1 GiB of memory).
b) Netfront would have used up to 1 MiB already even with moderate
data rates (there was no adjustment of target based on memory
pressure).
c) Small VMs are going to typically have one VCPU and hence only one
queue.
Keeping the ring full of Rx requests handles bursty traffic better
than trying to converge on an optimal number of requests to keep
filled.
On a 4 core host, an iperf -P 64 -t 60 run from dom0 to a 4 VCPU guest
improved from 5.1 Gbit/s to 5.6 Gbit/s. Gains with more bursty
traffic are expected to be higher.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the sync xmit handling into an async xmit handling. The
driver was already prepared for this step, all other drivers need more
work to implement a xmit_async function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the existsing xmit callback to xmit_sync and
introduces an asynchronous xmit_async function. If ieee802154_ops
doesn't provide the xmit_async callback, then we have a fallback to
the xmit_sync callback.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c: In function ‘xgene_enet_ecc_init’:
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:126: warning: ‘data’ may be used uninitialized in this function
Depending on the arbitrary value on the stack, the loop may terminate
too early, and cause a bogus -ENODEV failure.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally mask by the _SHIFT variable. It means that "event" is
always zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to cancel the work queue after rcu grace period,
otherwise it can be rescheduled by incoming packets.
We need to purge queue if some skbs are still in it.
We can use __skb_queue_head_init() variant in
macvlan_process_broadcast()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 412ca1550c ("macvlan: Move broadcasts into a work queue")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the NAPIfication of sunvnet, we no longer need to
synchronize by doing irqsave/restore on vio.lock in the
I/O fastpath.
NAPI ->poll() is non-reentrant, so all RX processing occurs
strictly in a serialized environment. TX reclaim is done in NAPI
context, so the netif_tx_lock can be used to serialize
critical sections between Tx and Rx paths.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A vnet_port_remove could be triggered as a result of an ldm-unbind
operation by the peer, module unload, or other changes to the
inter-vnet-link configuration. When this is concurrent with
vnet_start_xmit(), there are several race sequences possible,
such as
thread 1 thread 2
vnet_start_xmit
-> tx_port_find
spin_lock_irqsave(&vp->lock..)
ret = __tx_port_find(..)
spin_lock_irqrestore(&vp->lock..)
vio_remove -> ..
->vnet_port_remove
spin_lock_irqsave(&vp->lock..)
cleanup
spin_lock_irqrestore(&vp->lock..)
kfree(port)
/* attempt to use ret will bomb */
This patch adds RCU locking for port access so that vnet_port_remove
will correctly clean up port-related state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dwight Engen <dwight.engen@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move Rx packet procssing to the NAPI poll callback.
Disable VIO interrupt and unconditioanlly go into NAPI
context from vnet_event.
Note that we want to minimize the number of LDC
STOP/START messages sent. Specifically, do not send a STOP
message if vnet_walk_rx does not read all the available descriptors
because of the NAPI budget limitation. Instead, note the end index
as part of port state, and resume from this index when the
next poll callback is triggered.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Acked-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The identical struct of the wireless stack implementation is named
ieee80211_hw. This is useful to name the variable hw instead of get
confusing with netdev dev variable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the not functional fakehard driver. We don't support
HardMAC 802.15.4 drivers right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the ieee802154 header into include/linux instead
include/net. Similar like wireless which have the ieee80211 header
inside of include/linux.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wpan-phy header contains the wpan_phy struct information. Later this
header will be have similar function like cfg80211 header. The cfg80211
header contains the wiphy struct which is identically the wpan_phy
struct inside 802.15.4 subsystem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a frontend not receiving packets it is useful to detect this and
turn off the carrier so packets are dropped early instead of being
queued and drained when they expire.
A to-guest queue is stalled if it doesn't have enough free slots for a
an extended period of time (default 60 s).
If at least one queue is stalled, the carrier is turned off (in the
expectation that the other queues will soon stall as well). The
carrier is only turned on once all queues are ready.
When the frontend connects, all the queues start in the stalled state
and only become ready once the frontend queues enough Rx requests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netback needs to discard old to-guest skb's (guest Rx queue drain) and
it needs detect guest Rx stalls (to disable the carrier so packets are
discarded earlier), but the current implementation is very broken.
1. The check in hard_start_xmit of the slot availability did not
consider the number of packets that were already in the guest Rx
queue. This could allow the queue to grow without bound.
The guest stops consuming packets and the ring was allowed to fill
leaving S slot free. Netback queues a packet requiring more than S
slots (ensuring that the ring stays with S slots free). Netback
queue indefinately packets provided that then require S or fewer
slots.
2. The Rx stall detection is not triggered in this case since the
(host) Tx queue is not stopped.
3. If the Tx queue is stopped and a guest Rx interrupt occurs, netback
will consider this an Rx purge event which may result in it taking
the carrier down unnecessarily. It also considers a queue with
only 1 slot free as unstalled (even though the next packet might
not fit in this).
The internal guest Rx queue is limited by a byte length (to 512 Kib,
enough for half the ring). The (host) Tx queue is stopped and started
based on this limit. This sets an upper bound on the amount of memory
used by packets on the internal queue.
This allows the estimatation of the number of slots for an skb to be
removed (it wasn't a very good estimate anyway). Instead, the guest
Rx thread just waits for enough free slots for a maximum sized packet.
skbs queued on the internal queue have an 'expires' time (set to the
current time plus the drain timeout). The guest Rx thread will detect
when the skb at the head of the queue has expired and discard expired
skbs. This sets a clear upper bound on the length of time an skb can
be queued for. For a guest being destroyed the maximum time needed to
wait for all the packets it sent to be dropped is still the drain
timeout (10 s) since it will not be sending new packets.
Rx stall detection is reintroduced in a later commit.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frontends that do not provide feature-rx-notify may stall because
netback depends on the notification from frontend to wake the guest Rx
thread (even if can_queue is false).
This could be fixed but feature-rx-notify was introduced in 2006 and I
am not aware of any frontends that do not implement this.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixs a typo in address filter defines from IEEE802515 to
IEEE802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the FSF address in files which belongs to ieee802154
and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The async error function will already printout the errno over dev_err.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sometimes the async state function is call in an context where the spi
irq is diabled. This patch fix the handling to enable the irq when
spi_async failed in the async state change calling chain. We do this by
a context parameter irq_enable and evaluate this parameter when
spi_async failed instead of returning spi_async errno.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the driver waits for a tx completion currently the driver direct
enables the irq. When we switching to RX_AACK_ON some steps afterwards
the driver could receive a new frame and request resources which are
already in use, for example irq state change resource.
To be sure there are no new interrupts when we switching to RX_AACK_ON,
we enable the irq when state change to RX_AACK_ON was completed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a missing enable_irq when spi_async in isr failed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes dereferencing irq number over spi struct. Instead we
doing it directly over isr paramater.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds lifs/sifs handling only if max_frame_retries is above
zero. The at86rf2xx datasheets says nothing about phy lifs/sifs
handling. I asked the atmel support and they said lifs/sifs is done
by phy when max_frame_retries is above zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an async error handling function if sync state change
runs into a timeout. The async error handling function tries to recover
the phy state machine into a valid state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The rc variable is zero if we get a timeout. Instead of pass the rc
variable to the async error handling function which try to recover the
phy, we use a static -ETIMEDOUT errno.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MRF24J40MC module has an external amplifier which should be
enabled. The TX power has to be lowered to meet FCC regs.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-23
This series contains updates to i40e and i40evf.
Jesse modifies the i40e driver to only notify the firmware on link up/down
and qualified module events. Also simplified the job of managing link
state by using the admin queue receive event for link events as a signal
to tell the driver to update link state.
Jeff (me) cleans up the inconsistent use of tabs for indentation in the admin
queue command header file.
Neerav converts the use of udelay() to usleep_range().
Anjali fixes a bug where receive would stop after some stress by adding
a sleep and restart as well as moving the setting of flow control because
it should be done at a PF level and not a VSI level.
Mitch adds code to handle link events when updating the PF switch, which
allows link information to be properly provided to VFS in all cases.
Catherine adds driver support for 10GBaseT and bumps driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With properly using libphy PHYs now, remove the in-driver PHY
mangling.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell Ethernet IP supports PHY negotiation driven by HW. This
fundamentally clashes with libphy (software) driven negotiation and
also cannot cope with quirky PHYs. Therefore, always disable any HW
negotiation features and properly use libphy's phy_device.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current libphy handling in pxa168_eth lacks proper phy_connect. Prepare
to fix this by first moving phy properties from platform_data to private
driver data.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E3016 is a FastEthernet PHY that also can be found in Marvell
Berlin SoCs as integrated PHY.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rts threshold was being configured instead of
fragmentation threshold.
Keep in mind available firmware binaries don't
seem to support fragmentation anyway so this
doesn't fix fragmentation threshold per se.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user space requests survey info, it is useful to know which of the survey
data refers to the channel that is currently actively being used. One of the
use cases is getting the current channel noise for status output. Without this
flag you would have to look up the channel separately and then compare it
against the frequency in the survey output in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of defining a completely new tracepoint
use an existing tracepoint class.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fundamentally this was wrong. Tsf is only valid
in last MPDU of a PPDU. This means tsf value was
wrong most of the time during heavy traffic.
Also I don't see much point in exposing a
redundant (and broken) tsf value. Userspace can
already read it from the dumped rx descriptor
buffer.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once driver entered the rx_confused state it would
refuse to rx even after firmware is restarted.
Make sure to clear it so that rx works after, e.g.
hw restart or after all interfaces are stopped.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In theory it was possible to drain entire HTT Rx
ring via fragmented Rx leading to Rx lockup.
In practice non-data traffic would always trigger
replenishment via the regular Rx handler.
For correctness sake make sure to replenish the
ring on fragmented Rx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The netbuf pop can return NULL. Make sure to check
for that. It shouldn't happen but better safe than
sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's little point in dropping, e.g. frames with
FCS error early in ath10k.
This simplifies amsdu_allowed() and gets rid of
htt_rx_mpdu_status usage finally.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Treat non-chained and chained popping the same
way. Also this makes netbuf pop fully symmetrical
to (re)filling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tracing function was called before buffers were
unmapped from DMA.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the globally defined ieee80211 values instead
of re-defining them in the driver again.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx descriptor variable was no longer used in
the rx handler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT_RX_IND_MPDU_STATUS_MGMT_CTRL was pretty greedy
and because of that ath10k ended up dropping
Control Frames as well as Null Func frames.
Reported-by: Okhwan Lee <ohlee@mwnl.snu.ac.kr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not always convenient to have to know the device-id,
so allow deleting by name as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[use wiphy_name() instead of dev_name()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This gives a view into packet activity at the virtual radio
level.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As of commit e4dc601bf9 ("m68k: Disable/restore interrupts in
hwreg_present()/hwreg_write()"), this is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit e4dc601bf9 ("m68k: Disable/restore interrupts in
hwreg_present()/hwreg_write()"), this is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both image_data and typhoon_fw->data are const u8*, so the cast to u8*
is unnecessary and confusing.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e version to 1.0.21.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the three variables out of the loop, so it only declares once.
Change-ID: I436913777c7da3c16dc0031b59e3ffa61de74718
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add driver support for 10GBaseT device.
Change-ID: I4be6ed847ac0bddd220b9878a95c523b32038174
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to handle link events when updating the PF switch. This
allows link information to be properly provided to VFs in all cases.
Change-ID: If314c95f3d39259ef4c40a4a3b823381e28fb24f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the setting of flow control because this should be done at a pf level not
a vsi level. Also add a sleep and restart an to fix a bug where Rx would stop
after some stress.
Change-ID: I9a93d8c2ff27c39339eb00bc4ec1225e43900be0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the Documentation/timers/timers-howto.txt it is preferred to use
usleep_range() instead of udelay() if the delay value is > 10us in
non-atomic contexts.
So, replacing all the instances of udelay() with 10 or greater than 10
micro seconds delay in the driver and using usleep_range() instead.
Change-ID: Iaa2ab499a4c26f6005e5d86cc421407ef9de16c7
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is one small step in making the indentation more consistent. If
we truly want to align values, then use tabs rather than spaces.
Change-ID: I12368bc77a52f296d1843fdcb67201a7d7cd4749
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
The driver can do a simpler job of managing link state by simply
using the admin queue receive event for link events as a doorbell
that tells the driver to update link state.
Additionally, add a workaround will help make sure the link state in the
hardware is consistent with the link state the driver is reporting
by refreshing the link state every service task interval.
Change-ID: Ib95b5b7b8cc016e97d8009f6363c9f9eed301444
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tell the firmware what kind of link related events the driver is
interested in. In this case, just link up/down and qualified module
events are the ones the driver really cares about.
Change-ID: If132c812c340c8e1927c2caf6d55185296b66201
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.
Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:
iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]
Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.
This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581
But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:
https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809
Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54c5 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.
Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.
We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Drivers that do not use the get_btc_status() callback may not define a
dummy routine. The caller needs to check before making the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Thadeu Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a previous patch the call to ieee80211_register_hw was moved from the
load firmware callback to the rtl_pci_probe only.
rt8192cu also uses this callback. Currently it doesnt create a wlan%d device.
Fill in the call to ieee80211_register_hw in rtl_usb_probe.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize function pointer with a function indicating bt coexist is not there.
Prevents Ooops.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reported a possible array overrun. The affected code
checks for overruns, but fails to take the steps necessary to fix them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.
Bug: https://dev.openwrt.org/ticket/18164
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name
can never accidentally leak information via a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And changed from using strncat to strlcat to simplify code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver logs a message when the default branch of switch statements are
taken. Such information is useful when debugging, but these log items should
not be seen for standard usage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling init to reinit ce pipe state would also
re-set all static structure links and setting
(which don't change over driver lifecycle).
Make it so alloc links structures and initializes
static data and init part to setup state
variables and clear stuff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was the final missing bit to making sure the
device doesn't assert interrupts to host.
This should fix possible race when target crashes
during driver teardown.
This also removes an early warm reset workaround
during pci probing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If MSI isn't configured device ROM program expects
legacy interrupts to be enabled before it can
fully boot. Don't forget to disable legacy
interrupts after that.
While at it re-use the legacy irq enabling helper
instead of calling ath10k_pci_write32().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
total_data_buflen is used by netvsc_send() to decide if a packet can be put
into send buffer. It should also include the size of RNDIS message before the
Ethernet frame. Otherwise, a messge with total size bigger than send_section_size
may be copied into the send buffer, and cause data corruption.
[Request to include this patch to the Stable branches]
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the amd-xgbe driver increments the packets processed counter
each time a descriptor is processed. Since a packet can be represented
by more than one descriptor incrementing the counter in this way is not
appropriate. Also, since multiple descriptors cause the budget check
to be short circuited, sometimes the returned value from the poll
function would be larger than the budget value resulting in a WARN_ONCE
being triggered.
Update the polling logic to properly account for the number of packets
processed and exit when the budget value is reached.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support. Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 278d240478 (net: fec: ptp: Enable PPS output based on ptp clock)
fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls
into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to
dereference the NULL pointer.
Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called,
and fep->ptp_clock is NULL, which reliably causes a kernel panic.
This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After interface restart (eg: after link disconnection/reconnection), the bridge
function doesn't work anymore. This is due to the promiscuous mode being cleared
by the restart.
The mac-fcc already includes code to set the promiscuous mode back during the restart.
This patch adds the same handling to mac-fec and mac-scc.
Tested with bridge function on MPC885 with FEC.
Reported-by: Germain Montoies <germain.montoies@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_count and insert_count can wrap around, making > check invalid.
Fixes: 70b33fb0dd ("sfc: add support for
skb->xmit_more").
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is shown when spinlock debug is enabled.
This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.
Fix this by using spink_lock_bh().
=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b8 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
[<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
[<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
[<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
[<ffffffff810bcd07>] call_timer_fn+0x77/0x100
[<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
[<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
[<ffffffff8105fdae>] irq_exit+0x8e/0xb0
[<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
[<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
[<ffffffff81018143>] default_idle+0x13/0x20
[<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
[<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
[<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&enic->rfs_h.lock)->rlock);
<Interrupt>
lock(&(&enic->rfs_h.lock)->rlock);
*** DEADLOCK ***
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply changes the source for txpower setup.
It does not make ath10k use different txpower
values for different vifs.
This will make it easier to implement chanctx in
ath10k in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using global channel won't work with chanctx. Try
to determine the channel from the information
provided in the wmi event itself alone. This
should be sufficient.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code can be symmetrical so make it so. This
makes it easier to understand and work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reconfigure peer
completely upon reassociation. This will make it
easier to have a more uniform association code
across different modes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to pass bss_conf explicitly as it
is accessible via vif pointer. This requires
slight changes in function prototypes. While at it
clean up listen interval workaround/command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A frequent request have been to be able to provide calibration data from a
file as some of the AP devices store the calibration data on an MTD partition.
This patchset adds support for that and also makes it easier to add Device Tree
support later on.
The calibration data is found by using the id string provided by dev_name()
using this format:
cal-<bus>-<id>.bin
With PCI the id string contains bus, slot and func values. For example for a
PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from
a file:
/lib/firmware/ath10k/cal-pci-0000:02:00.0.bin
The calibration data sequence is:
1. Check with request_firmware() if there's a calibration file
("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If
not, goto 2
2. Check if otp.bin is able to successfully load the calibration data
from OTP. If yes, use that. If not, goto 3.
4. Print an error message that no calibration data found and stop driver
initialization for this device.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3a0861fffd ("ath10k: remove ath10k_bus") removed enum ath10k_bus
because it was not used for anything at the time. But now it's needed for for
retrieving the right calibration data file so add it back. Only new addition is
ath10k_bus_str().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
drivers/net/usb/ax88179_178a.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
been sitting in MST's tree during my vacation. I changed a function name
and made one trivial change, then they spent two days in linux-next.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JK6x
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.
skb->truesize can be very different from skb->len, that has
a very specific safety purpose.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0
Fixes: b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't ring the doorbell, and don't do PIO. This will also prevent
TX Push, because there will be more than one buffer waiting when
the doorbell is rung.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that the IP header has optional field at the end, this patch will
get the port numbers after that field, and compute the hash. The general
parser skb_flow_dissect() is used here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull maybe change skb->data and make eth pointer oboslete,
so eth needs to reload
Fixes: 91269e390d ("vxlan: using pskb_may_pull as early as possible")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().
The following patch is all we need to protect against this panic:
ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiling with CONFIG_FM10K=y and VXLAN=m resulting in linking error:
drivers/built-in.o: In function `fm10k_open':
(.text+0x1f9d7a): undefined reference to `vxlan_get_rx_port'
make: *** [vmlinux] Error 1
The fix follows the same strategy as I40E.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After grabbing the mailbox lock and detecting an error, the lock must be
released before the error code can be returned.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the flag to fetch the host state before kicking off the service task
that reads the host state when bringing the interface back up.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
pskb_may_pull should be used to check if skb->data has enough space,
skb->len can not ensure that.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when netif_rx() is done, the netif_rx handled skb maybe be freed,
and should not be used.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each Rx frame the eTSEC writes its FCS (Frame Check Sequence)
to the Rx buffer.
The eTSEC h/w manual states in the "Receive Buffer Descriptor Field
Descriptions" table:
"Data length is the number of octets written by the eTSEC into this BD's
data buffer if L is cleared (the value is equal to MRBLR), or, if L is
set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00),
preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and
any padding (RCTRL[PAL])."
Though the FCS bytes are removed by the driver before passing the skb
to the net stack, the Rx buffer size computation does not currently
take into account the FCS bytes (4 bytes).
Because the Rx buffer size is multiple of 512 bytes, leaving out the
FCS is not a problem for the default MTU of 1500, as the Rx buffer size
is 1536 in this case. However, for custom MTUs, where the difference
between the MTU size and the Rx buffer size is less, this can be a
problem as the computed Rx buffer size won't be enough to accomodate
the FCS for a received frame that is big enough (close to MTU size).
In such case the received frame is considered to be incomplete (L flag
not set in the RxBD status) and silently dropped.
Note that the driver does not currently support S/G on Rx, so it has to
compute its Rx buffer size based on the MTU of the device.
Reported-by: Kristian Otnes <kotnes@cisco.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0b725a2ca6
net: Remove ndo_xmit_flush netdev operation, use signalling instead.
added code that looks at skb->xmit_more after the skb has
been put in TX VQ. Since some paths process the ring and free the skb
immediately, this can cause use after free.
Fix by storing xmit_more in a local variable.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.
ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;
For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.
Changes V2:
Modify the commit/comments log to describe the issue clearly.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch is to fix the stmmac data compatibilities for
all the SoCs inside the platform file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
cxgb4 ipv6 does not guard against ipv6 being disabled, or the standard
ipv6 module vs inbuilt tri-state issue. This was fixed for cxgb4i & iw_cxgb4
but missed for cxgb4.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4 already handles CLIP updates from a previous changeset for iw_cxgb4,
there is no need to have this functionality in cxgb4i. Remove duplicated code
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after restore returns, virtio net violated this
rule by using receive VQs within restore.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In the extremely unlikely event that driver initialization fails after
RX buffers are added, virtio net frees RX buffers while VQs are
still active, potentially causing device to use a freed buffer.
To fix, reset device first - same as we do on device removal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, virtio net violated this
rule by using receive VQs within probe.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
goto done;
done:
return;
is ugly, it was put there to make diff review easier.
replace by open-coded return.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
config_mutex served two purposes: prevent multiple concurrent config
change handlers, and synchronize access to config_enable flag.
Since commit dbf2576e37
workqueue: make all workqueues non-reentrant
all workqueues are non-reentrant, and config_enable
is now gone.
Get rid of the unnecessary lock.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>