The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds auto TDLS support to mwifiex.
Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.
So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.
Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.
Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.
To record tx ieee80211 headers
trace-cmd record -e ath10k_tx_hdr
To record complete packets
trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fix an copy&paste issue in the comment of setting symbol
duration. These comments are more correct according the at86rf212 datasheet
now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Also provide ethtool -x support to fetch RSS key
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Rename rss_hkey local variable to rss_key to have consistent name among
drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lendacky, Thomas <Thomas.Lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6171 driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip also has a temperature sensor which can be read using the
common code. In order to use it, add the needed mutex protection for
accessing registers via the shared code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of any failure ieee802154fake_probe() just calls unregister_netdev().
But it does not look safe to unregister netdevice before it was registered.
The patch implements straightforward resource deallocation in case of
failure in ieee802154fake_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Sathya Perla <sperla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not
other UDP-based encapsulation protocols where the format and size of the
header differs. This patch implements a generic ndo_gso_check() for
VXLAN which will only advertise GSO support when the skb looks like it
contains VXLAN (or no UDP tunnelling at all).
Implementation shamelessly stolen from Tom Herbert:
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-13
Please pull this set of a few more wireless fixes intended for the
3.18 stream...
For the mac80211 bits, Johannes says:
"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
For the iwlwifi bits, Emmanuel says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
On top of that...
Arend van Spriel corrects a channel width conversion that caused a
WARNING in brcmfmac.
Hauke Mehrtens avoids a NULL pointer dereference in b43.
Larry Finger hits a trio of rtlwifi bugs left over from recent
backporting from the Realtek vendor driver.
Miaoqing Pan fixes a clocking problem in ath9k that could affect
packet timestamps and such.
Stanislaw Gruszka addresses an payload alignment issue that has been
plaguing rt2x00.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only match against local port number in order to reuse
socket. But if this new vxlan wants an IPv6 socket and a IPv4 one bound
to that port, vxlan will reuse an IPv4 socket as IPv6 and a panic will
follow. The following steps reproduce it:
# ip link add vxlan6 type vxlan id 42 group 229.10.10.10 \
srcport 5000 6000 dev eth0
# ip link add vxlan7 type vxlan id 43 group ff0e::110 \
srcport 5000 6000 dev eth0
# ip link set vxlan6 up
# ip link set vxlan7 up
<panic>
[ 4.187481] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
...
[ 4.188076] Call Trace:
[ 4.188085] [<ffffffff81667c4a>] ? ipv6_sock_mc_join+0x3a/0x630
[ 4.188098] [<ffffffffa05a6ad6>] vxlan_igmp_join+0x66/0xd0 [vxlan]
[ 4.188113] [<ffffffff810a3430>] process_one_work+0x220/0x710
[ 4.188125] [<ffffffff810a33c4>] ? process_one_work+0x1b4/0x710
[ 4.188138] [<ffffffff810a3a3b>] worker_thread+0x11b/0x3a0
[ 4.188149] [<ffffffff810a3920>] ? process_one_work+0x710/0x710
So address family must also match in order to reuse a socket.
Reported-by: Jean-Tsung Hsiao <jhsiao@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now allow up to 126 VFs. Note though that certain firmware
versions only allow up to 80 VFs. Moreover, old HCAs only support 64 VFs.
In these cases, we limit the maximum number of VFs to 64.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.
Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.
Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QUERY_FUNC firmware command could be used in order to query the
number of EQs, reserved EQs, etc for a specific function.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mlx4_load_one, as a preparation step for a new and
more complicated load function. The goal is to support both
newer firmware that required init_hca to be done before
enable_sriov and legacy firmwares that requires things to
be done the other way around.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactoring mlx4_cmd_init and mlx4_cmd_cleanup such that partial init
and cleanup are possible. After this refactoring, calling mlx4_cmd_init
several times is safe.
This is necessary in the VF init flow when mlx4_init_hca returns -EACCESS,
we need to issue cleanup and re-attempt to call it with the slave flag.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've used an incorrect type for the loop counter and the
mlx4_QUERY_FUNC_CAP function. The current input modifier
is either a port or a boolean.
Since the number of ports is always a positive value < 255,
we should use u8 instead of an integer with casting.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We mistakenly read the reserved_eqs field as a standard
numeric value rather than a log2 value.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree probing for R-Car M2N (r8a7793) is added.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RMMI mode, it is necessary to change in probe.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large receive offloading is known to cause problems if received packets
are passed to other host. Therefore the kernel disables it by calling
dev_disable_lro() whenever a network device is enslaved in a bridge or
forwarding is enabled for it (or globally). For virtual devices we need
to disable LRO on the underlying physical device (which is actually
receiving the packets).
Current dev_disable_lro() code handles this propagation for a vlan
(including 802.1ad nested vlan), macvlan or a vlan on top of a macvlan.
It doesn't handle other stacked devices and their combinations, in
particular propagation from a bond to its slaves which often causes
problems in virtualization setups.
As we now have generic data structures describing the upper-lower device
relationship, dev_disable_lro() can be generalized to disable LRO also
for all lower devices (if any) once it is disabled for the device
itself.
For bonding and teaming devices, it is necessary to disable LRO not only
on current slaves at the moment when dev_disable_lro() is called but
also on any slave (port) added later.
v2: use lower device links for all devices (including vlan and macvlan)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a missing break statement so we set everything to
PKT_HASH_TYPE_L3 even when we intended to use PKT_HASH_TYPE_L4.
Fixes: 5b9dfe299e ('amd-xgbe: Provide support for receive side scaling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.
Initially found by code review, confirmed later using test case.
This is low probability issue, and in order to reproduce it you have to
run the script:
while true; do
ifconfig eth0 down
ifconfig eth0 up || break
done
While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:
[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactored all macros used in cxgb4i as part of previously started cxgb4 macro
names cleanup. Makes them more uniform and avoids namespace collision.
Minor changes in other drivers where required as some of these macros are used
by multiple drivers, affected drivers are iw_cxgb4, cxgb4(vf) & csiostor
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two issues after using iovec iterators:
- vlan_offset should be initialized to zero, otherwise unexpected offset
will be used in skb_copy_datagram_iter()
- advance iovec iterator when vnet_hdr_sz is greater than sizeof(gso), this
is the case when mergeable rx buffer were enabled for a virt guest.
Fixes e0b46d0ee9 ("tun: Use iovec iterators")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the interframe spacing time workaround from at86rf230
driver and use the mac802154 one. The interframe spacing time differs at
at86rf212 and channel setting. This patch fix this handling which is also
a new workaround and should be moved into mac802154 while channel
setting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new interframe spacing time handling into mac802154
layer. Interframe spacing time is a time period between each transmit.
This patch adds a high resolution timer into mac802154 and starts on
xmit complete with corresponding interframe spacing expire time if
ifs_handling is true. We make it variable because it depends if
interframe spacing time is handled by transceiver or mac802154. At the
timer complete function we wake the netdev queue again. This avoids
new frame transmit in range of interframe spacing time.
For synced driver we add no handling of interframe spacing time. This
is currently a lack of support in all synced xmit drivers. I suppose
it's working because the latency of workqueue which is needed to call
spi_sync.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. bcm_sysport_tx_poll()
always returns 0 whether or not we completed the poll quantum.
Fix this by returning either 0 when we did complete the TX ring reclaim,
or budget to trigger a repoll.
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. In tx napi poll we always return 0.
So tx napi is not called again and we do not clean up the tx ring.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the host uses packet encapsulation feature, the MTU may be reduced by the
host due to headroom reservation for encapsulation. This patch handles this
new MTU value.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the types of the descriptor entries in the xgbe_ring_desc struct
from u32 to __le32 to fix endian warnings issued by sparse.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to ensure the net_device's dev.parent is set before we used it
in dma_zalloc_coherent() from init_hash_table().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.
However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.
This patch should also be applied to v3.17.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warning that got introduced in commit e2ac962895
("cxgb4: Cleanup macros so they follow the same style and look consistent, part
2") due to accidental checkin of bogus line.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* In LLD_MANAGED mode, traffic classes were being returned in reverse order to
lldp agent.
* Priotype of strict is no longer the default returned.
* Change behaviour of getdcbx() based on discussions on lldp-devel
These were missed as there was no working fetch interface for open-lldp when
running in LLD_MANAGED mode till now.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is unplugged or !netif_running(), the workqueue
doesn't need to wake the device, and could return directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid
re-schedule the tasklet again by workqueue.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_LIST_HEAD(&tp->rx_done) would be done in rtl_start_rx(),
so remove the unnecessary one in alloc_all_mem().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY revisions E0 and F0 share the same shorter workaround initialization
sequence. Dedicate a special function for these two PHY revisions to
perform the needed workaround sequence.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY revision D0 requires a specific workaround sequence which needs to
be applied to get the HW to behave properly in all corner cases
conditions. Do this based on the revision we just read out of the HW
using a specific function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function performs a R/RC calibration reset and will start being
used by more than one function in the next patches, create a helper
function to factor code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm7445_config_init() was working around non-production version of the
PHY HW block, so just remove it entirely.
bcm7xxx_28nm_afe_config_init() was running for all PHY revisions greater
than B0, but this workaround sequence is really specific to the B0 PHY
revision, so rename the function accordingly and update the GPHY macro
to use the generic config_init callback.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm7xxx_28nm_config_init() can be called as frequently as needed by the
PHY library upon suspend/resume cycles and interface bring up/down, just
print the PHY revision once and for all in order not to spam kernel
logs.
Fixes: d8ebfed3f1 ("net: phy: bcm7xxx: utilize PHY revision in config_init")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal kernel debugging mechanism which also
enables dynamic_debug at the same time.
Other miscellanea:
o Remove sysctl for irda_debug
o Remove function tracing like uses (use ftrace instead)
o Coalesce formats
o Realign arguments
o Remove unnecessary OOM messages
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable led-mode configuration for KSZ8081 and KSZ8091.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up led-mode setup by introducing proper defines for PHY Control
registers 1 and 2 and only passing the register to the setup function.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure never to update more than two bits when setting the led mode,
something which could for example change the reference-clock setting.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable PHY address 0 as the broadcast address, so that it can be used
as a unique (non-broadcast) address on a shared bus.
Note that this can also be configured using the B-CAST_OFF pin on
KSZ9091, but that KSZ8081 lacks this pin and is also limited to
addresses 0 and 3.
Specifically, this allows for dual KSZ8081 setups.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and clean up broadcast disable.
Some Micrel PHYs have a broadcast-off bit in the Operation Mode Strap
Override register which can be used to disable PHY address 0 as the
broadcast address, so that it can be used as a unique (non-broadcast)
address on a shared bus.
Note that the KSZPHY_OMSO_RMII_OVERRIDE bit is set by default on
KSZ8021/8031.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure never to update the control register with random data (an
error code) by checking the return value after reading it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_driver_register with
module_phy_driver macro.
Compile tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a NULL pointer dereference when __tx_port_find() doesn't
find a matching port.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel drivers were pretty much just using the plain vanilla GFP flags
in their calls to __skb_alloc_page so this change makes it so that they use
dev_alloc_page which just uses GFP_ATOMIC for the gfp_flags value.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the calls to __skb_alloc_page that are passed NULL with calls to
__dev_alloc_page.
In addition remove __GFP_COLD flag from allocations as we only want it for
the Rx buffer which is taken care of by __dev_alloc_skb, not for any
secondary allocations such as the queue element transmit descriptors.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the bloated use of __skb_alloc_page and replace it with
__dev_alloc_page. In addition update the one other spot that is
allocating a page so that it allocates with the correct flags.
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the invalid max frame retries check from driver
layer. This is already handled by nl802154 framework. Also the IEEE
802.15.4 standard doesn't allow a frame retries setting above 7. This
seems to be valid for the at86rf230 transceiver but the chip running out
of spec then. We only allow settings according 802.15.4 right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid check on max csma backoffs in driver
layer. This is already handled by nl802154 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid backoff exponent check from driver layer.
This is already handled by nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes validation of page and channel while setting from
driver layer. This is already handled by nl802154 and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And use the more common mechanisms directly.
Other miscellanea:
o Coalesce formats
o Add missing newlines
o Realign arguments
o Remove unnecessary OOM message logging as
there's a generic stack dump already on OOM.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Status variable is never initialized, can carry an arbitrary value
on the stack and thus may let the function fail.
Fixes: e90dd26456 ("ixgbe: Make return values more direct")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While preparing an ad-hoc start command, the capability info bitmap is
needlessly set from the command, and then the ESS bit cleared.
Change to set the bitmap directly without reference to the command.
Signed-off-by: James Cameron <quozl@laptop.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wlcore_cmd_send_failsafe() function is only called in the cmd.c
file, where it is definde. Make it static.
Additionally, move the EXPORT_SYMBOL macro for wl1271_cmd_send() to
the right place.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for the minimum required buffer length in wlcore_cmd_send() and
wlcore_cmd_configure_failsafe. This ensures that we will never try to
use a buffer that is smaller than the required header.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's been observed that wrong firmware version (ex. 66.14.96.p9
instead of 14.66.9.p96) is displayed on big endian platforms.
The problem is fixed here.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use code provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use values provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason it didn't coused obvious problems.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
not sure why.
Initially provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename exports from ath9k_spectral_* to ath9k_cmn_spectral_*
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we should be ready to make this code common.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
last preparation before moving ath9k_spectral_scan_ to spectral.c
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we don't have here any ieee80211_hw dependencies any way.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spectral code mostly depends on ath_hw, not on ath_softc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this will alow us to make ath_softc independent code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and move rfs_chan_spec_scan to this struct. We will need it
for common spectral scan code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We see this warning while starting mwifiex AP:
Unsupported RX-STBC, default to 2x2
This was happening because of wrong offset while copying HT
capabilities from BSS configuration of start_ap handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is observed that device sometimes sends BA setup requests for
broadcast mac address.
This patch adds a check to avoid checking availability of
AMPDU/AMSDU streams for broadcast mac address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some platforms, system goes out of memory during heavy
Rx traffic with our USB chipsets.
In case of SDIO/PCIe, after receiving 50 packets in Rx queue
we stop processing interrupts till packets pending fall below
low threshold i.e 20. We don't have similar logic for USB,
so if host platform is slow, we would hit a case where firmware
keeps on pushing packets at high speed than driver/kernel can
process.
We will stop submitting URBs for Rx data when pending packet
count reaches high threshold and restart them when enough
packets are consumed to solve the problem.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=85071
Reported-by: Marek Belisko <marek.belisko@gmail.com>
Tested-by: Marek Belisko <marek.belisko@gmail.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes redundant data complete handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds RX workqueue support for USB interfaces.
Currently rx_pending is applicable for cmd/events and Rx
data in USB interface. Let's use it only for Rx data.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track it per channel context instead of in the softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-11-11
This series contains updates to i40e, i40evf and ixgbe.
Kamil updated the i40e and i40evf driver to poll the firmware slower
since we were polling faster than the firmware could respond.
Shannon updates i40e to add a check to keep the service_task from
running the periodic tasks more than once per second, while still
allowing quick action to service the events.
Jesse cleans up the throttle rate code by fixing the minimum interrupt
throttle rate and removing some unused defines.
Mitch makes the early init admin queue message receive code more robust
by handling messages in a loop and ignoring those that we are not
interested in. This also gets rid of some scary log messages that
really do not indicate a problem.
Don provides several ixgbe patches, first fixes an issue with x540
completion timeout where on topologies including few levels of PCIe
switching for x540 can run into an unexpected completion error. Cleans
up the functionality in ixgbe_ndo_set_vf_vlan() in preparation for
future work. Adds support for x550 MAC's to the driver.
v2:
- Remove code comment in patch 01 of the series, based on feedback from
David Liaght
- Updated the "goto" to "break" statements in patch 06 of the series,
based on feedback from Sergei Shtylyov
- Initialized the variable err due to the possibility of use before
being assigned a value in patch 07 of the series
- Added patch "ixgbe: add helper function for setting RSS key in
preparation of X550" since it is needed for the addition of X550 MAC
support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we were dereferencing dev to initialize pdata. but just after that we
have a BUG_ON(!dev). so we were basically dereferencing the pointer
first and then tesing it for NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When advertised capabilities are changed with mii-tool, such as:
mii-tool -A 10baseT
the existing handler has two errors.
- An actual PHY register value is provided by mii-tool, and this
must be mapped to internal state with mii_adv_to_ethtool_adv_t().
- The PHY state machine needs to be told that autonegotiation has
again been performed. If not, the MAC will not be notified of
the new link speed and duplex, resulting in a possible config
mismatch.
Signed-off-by: Brian Hill <Brian@houston-radar.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
chandef_to_chanspec.isra.11+0x158/0x184()
Modules linked in:
CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f #8
[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---
Cc: stable@vger.kernel.org # v3.17
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911https://bugzilla.kernel.org/show_bug.cgi?id=72471http://marc.info/?l=linux-wireless&m=139108549530402&w=2https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lnlA
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ppp_ioctl(), bpf_prog_create() is called inside ppp_lock, which
eventually calls vmalloc() and hits BUG_ON() in vmalloc.c. This patch
works around the problem by moving the allocation outside the lock.
The bug was revealed by the recent change in net/core/filter.c, as it
allocates via vmalloc() instead of kmalloc() now.
Reported-and-tested-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of registering the platform and PCI drivers in one module let's move
necessary bits to where it belongs. During this procedure we convert the module
registration part to use module_*_driver() macros which makes code simplier.
>From now on the driver consists three parts: core library, PCI, and platform
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currenly we only support Large-Send and TX checksum offloads for
encapsulated traffic of type VXLAN. We must make sure to advertize
these offloads up to the stack only when VXLAN tunnel is set.
Failing to do so, would mislead the the networking stack to assume
that the driver can offload the internal TX checksum for GRE packets
and other buggy schemes.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing received traffic, pass CHECKSUM_COMPLETE status to the
stack, with calculated checksum for non TCP/UDP packets (such
as GRE or ICMP).
Although the stack expects checksum which doesn't include the pseudo
header, the HW adds it. To address that, we are subtracting the pseudo
header checksum from the checksum value provided by the HW.
In the IPv6 case, we also compute/add the IP header checksum which
is not added by the HW for such packets.
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can call napi_gro_frags for all the received traffic regardless
of the checksum status. Specifically, received packets whose status
is CHECKSUM_NONE (and soon to be added CHECKSUM_COMPLETE)
are eligible for napi_gro_frags as well.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split off the setting of the RSS key into its own function. This
will help when we add support for X550 which can have different
RSS keys per pool.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will add in the new MAC defines and fit it into the switch
cases throughout the driver. New functionality and enablement support will
be added in following patches.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move setting of drop enable to support function. This not only makes the
code more readable but is also prep for following patches that add
additional MAC support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up functionality in ixgbe_ndo_set_vf_vlan that will simplify later
patches.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On topologies including few levels of PCIe switching X540 can run into an
unexpected completion error. We get around this by waiting after enabling
loopback a sufficient amount of time until Tx Data Fetch is sent. We then
poll the pending transaction bit to ensure we received the completion. Only
then do we go on to clear the buffers.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's kind of silly to configure and attempt to use a bunch of queue
pairs when you're running on a single (virtual) CPU. Instead of
unconditionally configuring all of the queues that the PF gives us,
clamp the number of queue pairs to the number of CPUs.
Change-ID: I321714c9e15072ee76de8f95ab9a81f86ed347d1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In early init, if we get an unexpected message from the PF (such as link
status), we just kick an error back to the init task, causing it to
restart its state machine and delaying initialization.
Make the early init AQ message receive code more robust by handling
messages in a loop, and ignoring those that we aren't interested in.
This also gets rid of some scary log messages that really didn't
indicate a problem.
Change-ID: I620e8c72e49c49c665ef33eeab2425dd10e721cf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt throttle rate minimum is actually 2us, so
fix that define and while we are there, remove some unused defines.
Change some strings in the function to be a bit less wrappy, and
express the correct limits.
Change-ID: I96829bbc77935e0b57c6f0fc1439fb4152b2960a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ARQ events cause a service_task execution, and we do a link_status
check and full stats gathering for each service_task. However, when
there are a lot of ARQ events, such as when doing an NVM update, we end up
doing 10's if not 100's of these per second, thereby heavily abusing the
PCI bus and especially the Firmware. This patch adds a check to keep the
service_task from running these periodic tasks more than once per second,
while still allowing quick action to service the events.
Change-ID: Iec7670c37bfae9791c43fec26df48aea7f70b33e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was polling the firmware tail register for completion every
10 microseconds, which is way faster than the firmware can respond.
This changes the poll interval to 1ms, which reduces polling CPU
utilization, and the number of times we loop.
The maximum delay is still 100ms.
Change-ID: I4bbfa6b66d802890baf8b4154061e55942b90958
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.
Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2cf7 ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After commit 1a28817282 ("mlx4: use napi_complete_done()") we ended up
calling napi_complete_done() in the case NAPI poll consumed all its
budget.
This added extra interrupt pressure, this patch restores proper
behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1a28817282 ("mlx4: use napi_complete_done()")
Signed-off-by: David S. Miller <davem@davemloft.net>
The out_dropped label will only do rcu_read_unlock for non-null port.
So add the missing rcu_read_unlock() when bailing due to non-null port.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per comments in vnet_start_xmit, for the edge case
when outgoing vnet_start_xmit() data and an incoming STOPPED
ACK cross each other in flight, we may need to send the missed
START trigger from maybe_tx_wakeup() after checking for a
false value of start_cons
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vnet_start_xmit() is concurrent with vnet_ack(), we may
have a race that looks like:
thread 1 thread 2
vnet_start_xmit vnet_event_napi -> vnet_rx
__vnet_tx_trigger for some desc X
at this point dr->prod == X
peer sends back a stopped ack for X
we process X, but X == dr->prod
so we bail out in vnet_ack with
!idx_is_pending
update dr->prod
As a result of the fact that we never processed the stopped ack for X,
the Tx path is led to incorrectly believe that the peer is still
"started" and reading, but the peer has stopped reading, which will
ultimately end in flow-control assertions.
The fix is to synchronize the above 2 paths on the netif_tx_lock.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver allows MTU up to 1518 bytes which is not enought to run
batman-adv. Simply raise the maximum packet size up to the maximum
allowed by the transmit descriptor, 1792 bytes, giving a maximum MTU
of 1774 bytes.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the default ndo_change_mtu callback with one that allow
setting MTU that the driver can handle.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike CEE, IEEE has a bespoke app delete call and does not rely on priority
for app deletion
Fixes : 2376c879b8 ('cxgb4 : Improve handling of DCB negotiation or loss
thereof')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing GRO processing for UDP tunnels, we never add
SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol
is added (such as SKB_GSO_TCPV4). The result is that if the packet is
later resegmented we will do GSO but not treat it as a tunnel. This
results in UDP fragmentation of the outer header instead of (i.e.) TCP
segmentation of the inner header as was originally on the wire.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-11-07
Please pull this batch of updates intended for the 3.19 stream!
For the mac80211 bits, Johannes says:
"This relatively large batch of changes is comprised of the following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
For the Bluetooth bits, Johan says:
"Here's the first bluetooth-next pull request for 3.19. The vast majority
of patches are for ieee802154 from Alexander Aring with various fixes
and cleanups. There are also several LE/SMP fixes as well as improved
support for handling LE devices that have lost their pairing information
(the patches from Alfonso). Jukka provides a couple of stability fixes
for 6lowpan and Szymon conformance fixes for RFCOMM. For the HCI drivers
we have one new USB ID for an Acer controller as well as a reset
handling fix for H5."
For the Atheros bits, Kalle says:
"Major changes are:
o ethtool support (Ben)
o print dev string prefix with debug hex buffers dump (Michal)
o debugfs file to read calibration data from the firmware verification
purposes (me)
o fix fw_stats debugfs file, now results are more reliable (Michal)
o firmware crash counters via debugfs (Ben&me)
o various tracing points to debug firmware (Rajkumar)
o make it possible to provide firmware calibration data via a file (me)
And we have quite a lot of smaller fixes and clean up."
For the iwlwifi bits, Emmanuel says:
"The big new thing here is netdetect which allows the
firmware to wake up the platform when a specific network
is detected. Along with that I have fixes for d3 operation.
The usual amount of rate scaling stuff - we now support STBC.
The other commit that stands out is Johannes's work on
devcoredump. He basically starts to use the standard
infrastructure he built."
Along with that are the usual sort of updates and such for ath9k,
brcmfmac, wil6210, and a handful of other bits here and there...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Free List Starvation Threshold needs to be larger than the SGE's Egress
Congestion Threshold or we'll end up in a mutual stall where the driver waits
for Ingress Packets to drive replacing Free List Pointers and the SGE waits for
Free List Pointers before pushing Ingress Packets to the host.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T5 introduces the ability to have separate Packing and Padding Boundaries
for SGE DMA transfers from the chip to Host Memory. This change set takes
advantage of that to set up a smaller Padding Boundary to conserve PCI Link
and Memory Bandwidth with T5.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move fl_starv_thres into adapter->sge data structure since it
_could_ be different from adapter to adapter. Also move other per-adapter
SGE values which had been treated as driver globals into adapter->sge.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ways drivers like cxgb4 don't need to do ugly relative includes.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_read and phy_write are not set for every phy any more sine this:
commit d342b95dd7
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Thu Jul 31 21:59:43 2014 +0200
b43: don't duplicate common PHY read/write ops
b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.
This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731
Reported-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various patches have ended up changing the style of the symbolic macros/register
defines to different style.
As a result, the current kernel.org files are a mix of different macro styles.
Since this macro/register defines is used by different drivers a
few patch series have ended up adding duplicate macro/register define entries
with different styles. This makes these register define/macro files a complete
mess and we want to make them clean and consistent. This patch cleans up a part
of it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various patches have ended up changing the style of the symbolic macros/register
to different style.
As a result, the current kernel.org files are a mix of different macro styles.
Since this macro/register defines is used by different drivers a
few patch series have ended up adding duplicate macro/register define entries
with different styles. This makes these register define/macro files a complete
mess and we want to make them clean and consistent. This patch cleans up a part
of it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable gro_flush_timeout, a driver has to use napi_complete_done()
instead of napi_complete().
Tested:
Ran 200 netperf TCP_STREAM from A to B (10Gbe mlx4 link, 8 RX queues)
Without this feature, we send back about 305,000 ACK per second.
GRO aggregation ratio is low (811/305 = 2.65 segments per GRO packet)
Setting a timer of 2000 nsec is enough to increase GRO packet sizes
and reduce number of ACK packets. (811/19.2 = 42)
Receiver performs less calls to upper stacks, less wakes up.
This also reduces cpu usage on the sender, as it receives less ACK
packets.
Note that reducing number of wakes up increases cpu efficiency, but can
decrease QPS, as applications wont have the chance to warmup cpu caches
doing a partial read of RPC requests/answers if they fit in one skb.
B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average: eth0 811269.80 305732.30 1199462.57 19705.72 0.00
0.00 0.50
B:~# echo 2000 >/sys/class/net/eth0/gro_flush_timeout
B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average: eth0 811577.30 19230.80 1199916.51 1239.80 0.00
0.00 0.50
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 3cc81d85ee ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olivier having laid the groundwork this patch transmits the
multicast flag to the device to save some bus traffic.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings. One is fixed by casting return
value to a return type of the function. The others by creating a specific
stmmac_platform.h which provides the bits related to the platform driver.
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: warning: incorrect type in return expression (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: expected void *
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: got void [noderef] <asn:2>*reg
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:64:29: warning: symbol 'meson6_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:354:29: warning: symbol 'stih4xx_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:361:29: warning: symbol 'stid127_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c:133:29: warning: symbol 'sun7i_gmac_data' was not declared. Should it be static?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a kernel helper to dump buffers in a hexdecimal format. This patch
substitutes the open coded function by calling that helper.
The output is slightly changed:
- no lead space
- ASCII part will be printed along with the dump
- offset is longer than 3 characters (now 8)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of skb_copy_datagram_const_iovec in
favour of the iovec iterator-based skb_copy_datagram_iter.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of skb_copy_datagram_const_iovec in
favour of the iovec iterator-based skb_copy_datagram_iter.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-06
Please pull this batch of fixes intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
For the iwlwifi bits, Emmanuel says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition to vxlan nla_policy for UDP checksum. This is necessary
to enable UDP checksums on VXLAN.
In some instances, enabling UDP checksums can improve performance on
receive for devices that return legacy checksum-unnecessary for UDP/IP.
Also, UDP checksum provides some protection against VNI corruption.
Testing:
Ran 200 instances of TCP_STREAM and TCP_RR on bnx2x.
TCP_STREAM
IPv4, without UDP checksums
14.41% TX CPU utilization
25.71% RX CPU utilization
9083.4 Mbps
IPv4, with UDP checksums
13.99% TX CPU utilization
13.40% RX CPU utilization
9095.65 Mbps
TCP_RR
IPv4, without UDP checksums
94.08% TX CPU utilization
156/248/462 90/95/99% latencies
1.12743e+06 tps
IPv4, with UDP checksums
94.43% TX CPU utilization
158/250/462 90/95/99% latencies
1.13345e+06 tps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb allocation fails during receive processing, the driver would
continue reading descriptors without first determining if there were
any more descriptors for the current packet. Update the code to check
whether more descriptors are associated with the current packet or
whether to move on to the next descriptor as a new packet.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channel structure is freed before freeing the per channel
interrupts resulting in a kernel oops. Move the call to free
the channel structure to after the freeing of the per channel
interrupts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vnet_event_napi() may be called as part of the NAPI ->poll,
to resume reading descriptor rings. When no data is available,
descriptor ring state (e.g., rcv_nxt) needs to be reset
carefully to stay in lock-step with ldc_read(). In the interest
of simplicity, the best way to do this is to return from
vnet_event_napi() when there are no more packets to read.
The next trip through ldc_rx will correctly set up the dring state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: David Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant tab.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PIDs are only used in the id table, so the definitions are
unnacessary. Remove them wouldn't have confusion.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace using VID/PID with using tp->version to initialize the ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move r8152b_get_version() to the location before rtl_ops_init().
Then, the rtl_ops_init() could use tp->version.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 is very similar to the mv88e6171. So extend the
mv88e6171 driver to support it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b9 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also add dummy functions where required to avoid NULL pointer dereference.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch in preparation for the upcoming EF10 sriov support.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series provides a base and cleanup for the
upcoming EF10 SRIOV support.
This patch moves the VF state into siena_nic_data as a basis to
save the VF state based on nic type.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditionally pulling 128 bytes into the linear area is not required
for:
- security: Every protocol demux starts with pskb_may_pull() to pull
frag data into the linear area, if necessary, before looking at
headers.
- performance: Netback has already grant copied up-to 128 bytes from
the first slot of a packet into the linear area. The first slot
normally contain all the IPv4/IPv6 and TCP/UDP headers.
The unconditional pull would often copy frag data unnecessarily. This
is a performance problem when running on a version of Xen where grant
unmap avoids TLB flushes for pages which are not accessed. TLB
flushes can now be avoided for > 99% of unmaps (it was 0% before).
Grant unmap TLB flush avoidance will be available in a future version
of Xen (probably 4.6).
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pr_* macros let's use dev_* macros which provide device name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate pci driver to managed resources to reduce boilerplate error handling
code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert system PM callbacks to use dev_pm_ops. In addition remove the PCI calls
related to a power state since the bus code cares about this already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last standard PCI resource is defined as PCI_STD_RESOURCE_END. Thus, we
could use it instead of plain integer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings.
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:381:30: warning: symbol 'enh_desc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:253:30: warning: symbol 'ndesc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:141:33: warning: symbol 'stmmac_ptp' was not declared. Should it be static?
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ieee802154/at86rf230.c:1365:1-3: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe-phy driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to sync the states of the PCS and the PHY
after a reset is performed. If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the spelling of the word "descriptor" in a couple
of locations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool receive side scaling (RSS) commands.
Support is added to get/set the RSS hash key and the RSS lookup table.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for receive side scaling (RSS). RSS allows
for spreading incoming network packets across the Rx queues. When used
in conjunction with the per DMA channel interrupt support, this allows
the receive processing to be spread across multiple processors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for interrupts that are generated by the
Tx/Rx DMA channel pairs of the device. This allows for Tx and Rx
processing to run across multiple processsors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide support for splitting IP packets so that the header and
payload can be sent to different DMA addresses. This will allow
the IP header to be put into the linear part of the skb while the
payload can be added as frags.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use page allocations for Rx buffers instead of pre-allocating skbs
of a set size.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx and Rx descriptors are unsigned 32 bit values. Use the u32
type, rather than unsigned int, to map these descriptors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pre_xmit function name implies that it performs operations prior
to transmitting the packet when in fact it is responsible for setting
up the descriptors and initiating the transmit. Rename this to
function from pre_xmit to dev_xmit, which is consistent with the name
used during receive processing - dev_read.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the channel and ring tracking structures allocation to device
open. This will allow for future support to vary the number of Tx/Rx
queues without unloading the module.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
