I often use "ethtool -i" command to check what driver controls the
ehternet device. But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:
# ethtool -i eth3
Cannot get driver information: Operation not supported
This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.
# ethtool -i eth3
driver: virtio_net
version: N/A
firmware-version: N/A
bus-info: virtio0
Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RxRPC can potentially deadlock as rxrpc_resend_time_expired() wants to get
call->state_lock so that it can alter the state of an RxRPC call. However, its
caller (call_timer_fn()) has an apparent lock on the timer struct.
The problem is that rxrpc_resend_time_expired() isn't permitted to lock
call->state_lock as this could cause a deadlock against rxrpc_send_abort() as
that takes state_lock and then attempts to delete the resend timer by calling
del_timer_sync().
The deadlock can occur because del_timer_sync() will sit there forever waiting
for rxrpc_resend_time_expired() to return, but the latter may then wait for
call->state_lock, which rxrpc_send_abort() holds around del_timer_sync()...
This leads to a warning appearing in the kernel log that looks something like
the attached.
It should be sufficient to simply dispense with the locks. It doesn't matter
if we set the resend timer expired event bit and queue the event processor
whilst we're changing state to one where the resend timer is irrelevant as the
event can just be ignored by the processor thereafter.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35-rc3-cachefs+ #115
-------------------------------------------------------
swapper/0 is trying to acquire lock:
(&call->state_lock){++--..}, at: [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
but task is already holding lock:
(&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&call->resend_timer){+.-...}:
[<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<ffffffff81056184>] lock_acquire+0x57/0x6d
[<ffffffff8103bb9c>] del_timer_sync+0x3c/0x86
[<ffffffffa002bb7a>] rxrpc_send_abort+0x50/0x97 [af_rxrpc]
[<ffffffffa002bdd9>] rxrpc_kernel_abort_call+0xa1/0xdd [af_rxrpc]
[<ffffffffa0061588>] afs_deliver_to_call+0x129/0x368 [kafs]
[<ffffffffa006181b>] afs_process_async_call+0x54/0xff [kafs]
[<ffffffff8104261d>] worker_thread+0x1ef/0x2e2
[<ffffffff81045f47>] kthread+0x7a/0x82
[<ffffffff81002cd4>] kernel_thread_helper+0x4/0x10
-> #0 (&call->state_lock){++--..}:
[<ffffffff81055237>] validate_chain+0x727/0xd23
[<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<ffffffff81056184>] lock_acquire+0x57/0x6d
[<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
[<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
[<ffffffff81036828>] __do_softirq+0xa2/0x13e
[<ffffffff81002dcc>] call_softirq+0x1c/0x28
[<ffffffff810049f0>] do_softirq+0x38/0x80
[<ffffffff810361a2>] irq_exit+0x45/0x47
[<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
[<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
[<ffffffff810011ac>] cpu_idle+0x4d/0x83
[<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1
other info that might help us debug this:
1 lock held by swapper/0:
#0: (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5
stack backtrace:
Pid: 0, comm: swapper Not tainted 2.6.35-rc3-cachefs+ #115
Call Trace:
<IRQ> [<ffffffff81054414>] print_circular_bug+0xae/0xbd
[<ffffffff81055237>] validate_chain+0x727/0xd23
[<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<ffffffff810539a7>] ? mark_lock+0x42f/0x51f
[<ffffffff81056184>] lock_acquire+0x57/0x6d
[<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
[<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
[<ffffffff8103b675>] ? run_timer_softirq+0x182/0x2a5
[<ffffffffa002007e>] ? rxrpc_resend_time_expired+0x0/0x96 [af_rxrpc]
[<ffffffff810367ef>] ? __do_softirq+0x69/0x13e
[<ffffffff81036828>] __do_softirq+0xa2/0x13e
[<ffffffff81002dcc>] call_softirq+0x1c/0x28
[<ffffffff810049f0>] do_softirq+0x38/0x80
[<ffffffff810361a2>] irq_exit+0x45/0x47
[<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
[<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
<EOI> [<ffffffff81049de1>] ? __atomic_notifier_call_chain+0x0/0x86
[<ffffffff8100955b>] ? mwait_idle+0x6e/0x78
[<ffffffff81009552>] ? mwait_idle+0x65/0x78
[<ffffffff810011ac>] cpu_idle+0x4d/0x83
[<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the TX path, skb->data points to the ethernet header, not the network
header. So when validating the packet length for accessing we should
take the ethernet header into account.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_netdev finally calls kfree which makes the contents
of ndev and priv (private data contained in ndev) invalid.
So iounmap should be called before free_netdev.
Cc: David S. Miller <davem@davemloft.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sriramakrishnan <srk@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
Revert "HID: add support for the Wacom Intuos 4 wireless"
HID: fix up Kconfig entry for ACRUX driver
HID: add ACRUX game controller force feedback support
HID: Force input registration for "VEC footpedal"
HID: add HID_QUIRK_HIDINPUT_FORCE
HID: hid-input.c: indentation fixes
HID: hiddev: use usb_find_interface, get rid of BKL
HID: ignore digitizer usage Undefined (0x00)
HID: Add support for Conceptronic CLLRCMCE
HID: hid-ids.h: Whitespace fixup, align using TABs
HID: picolcd: implement refcounting of framebuffer
HID: picolcd: do not reallocate memory on depth change
HID: picolcd: Add minimal palette required by fbcon on 8bpp
HID: magicmouse: Correct parsing of large X and Y motions.
HID: magicmouse: report last touch up
HID: picolcd: fix deferred_io init/cleanup to fb ordering
HID: hid-ids.h: keep vendor ids in alphabetical order
HID: add proper support for Elecom BM084 bluetooth mouse
HID: magicmouse: enable horizontal scrolling
HID: magicmouse: add param for scroll speed
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits)
random: Reorder struct entropy_store to remove padding on 64bits
padata: update API documentation
padata: Remove padata_get_cpumask
crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier
crypto: pcrypt - Rename pcrypt_instance
padata: Pass the padata cpumasks to the cpumask_change_notifier chain
padata: Rearrange set_cpumask functions
padata: Rename padata_alloc functions
crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask
padata: Check for valid cpumasks
padata: Allocate cpumask dependend recources in any case
padata: Fix cpu index counting
crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
pcrypt: Added sysfs interface to pcrypt
padata: Added sysfs primitives to padata subsystem
padata: Make two separate cpumasks
padata: update documentation
padata: simplify serialization mechanism
padata: make padata_do_parallel to return zero on success
padata: Handle empty padata cpumasks
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: allow limited allocation before slab is online
percpu: make @dyn_size always mean min dyn_size in first chunk init functions
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits)
[SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions
[SCSI] zfcp: Introduce experimental support for DIF/DIX
[SCSI] zfcp: Enable data division support for FCP devices
[SCSI] zfcp: Prevent access on uninitialized memory.
[SCSI] zfcp: Post events through FC transport class
[SCSI] zfcp: Cleanup QDIO attachment and improve processing.
[SCSI] zfcp: Cleanup function parameters for sbal value.
[SCSI] zfcp: Use correct width for timer_interval field
[SCSI] zfcp: Remove SCSI device when removing unit
[SCSI] zfcp: Use memdup_user and kstrdup
[SCSI] zfcp: Fix retry after failed "open port" erp action
[SCSI] zfcp: Fail erp after timeout
[SCSI] zfcp: Use forced_reopen in terminate_rport_io callback
[SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add
[SCSI] zfcp: Do not try "forced close" when port is already closed
[SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED
[SCSI] sd: add support for runtime PM
[SCSI] implement runtime Power Management
[SCSI] convert to the new PM framework
[SCSI] Unify SAM_ and SAM_STAT_ macros
...
82ca934176 added scary looking
but harmless error messages. Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The warning is:
net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.
CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02 and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SMC2802W appears to work with p54pci.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).
Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.
This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.
The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after
wl1271_dump().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
small typo fix in ucode_bt_stats_read debugfs file
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.
Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi is compiled w/o debug, we get
this warning:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type
iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’
because the const qualifier is missing in the
inline stub. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.
This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Releasing the scan mutex while starting scans
can lead to unexpected things happening, so
we shouldn't do that. Fix that and hold the
mutex across the scan triggering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit f84b29ec0a
Author: Johannes Berg <johannes.berg@intel.com>
Date: Tue May 18 02:29:13 2010 -0700
iwlwifi: queue user-initiated scan when doing internal scan
introduced a potential deadlock because it calls
ieee80211_scan_completed() with the priv->mutex
held, but mac80211 may call back into iwlwifi
which would lead to recursive locking. Move this
out from under the mutex.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6:
ibft: Use IBFT_SIGN instead of open-coding the search string.
ibft: convert iscsi_ibft module to iscsi boot lib
ibft: separate ibft parsing from sysfs interface
ibft: For UEFI machines actually do scan ACPI for iBFT.
ibft: Update iBFT handling for v1.03 of the spec.
Commit 8f92054e7c ("CRED: Fix __task_cred()'s lockdep check and banner
comment") fixed the lockdep checks on __task_cred(). This has shown up
a place in the signalling code where a lock should be held - namely that
check_kill_permission() requires its callers to hold the RCU lock.
Fix group_send_sig_info() to get the RCU read lock around its call to
check_kill_permission().
Without this patch, the following warning can occur:
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
kernel/signal.c:660 invoked rcu_dereference_check() without protection!
...
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bd_prepare_to_claim() incorrectly allowed multiple attempts for
exclusive open to progress in parallel if the attempting holders are
identical. This triggered BUG_ON() as reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=16393
__bd_abort_claiming() is used to finish claiming blocks and doesn't
work if multiple openers are inside a claiming block. Allowing
multiple parallel open attempts to continue doesn't gain anything as
those are serialized down in the call chain anyway. Fix it by always
allowing only single open attempt in a claiming block.
This problem can easily be reproduced by adding a delay after
bd_prepare_to_claim() and attempting to mount two partitions of a
disk.
stable: only applicable to v2.6.35
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The firmware handles '\t' internally, so stop trying to emulate it
(which, incidentally, had a bug in it.)
Fixes a really weird hang at bootup in rcu_bootup_announce, which,
as far as I can tell, is the first printk in the core kernel to use
a tab as the first character.
Cc: stable@kernel.org
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Add runtime PM statistics (v3)
PM / Runtime: Make runtime_status attribute not debug-only (v. 2)
PM: Do not use dynamically allocated objects in pm_wakeup_event()
PM / Suspend: Fix ordering of calls in suspend error paths
PM / Hibernate: Fix snapshot error code path
PM / Hibernate: Fix hibernation_platform_enter()
pm_qos: Get rid of the allocation in pm_qos_add_request()
pm_qos: Reimplement using plists
plist: Add plist_last
PM: Make it possible to avoid races between wakeup and system sleep
PNPACPI: Add support for remote wakeup
PM: describe kernel policy regarding wakeup defaults (v. 2)
PM / Hibernate: Fix typos in comments in kernel/power/swap.c
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (88 commits)
ips driver: make it less chatty
intel_scu_ipc: fix size field for intel_scu_ipc_command
intel_scu_ipc: return -EIO for error condition in busy_loop
intel_scu_ipc: fix data packing of PMIC command on Moorestown
Clean up command packing on MRST.
zero the stack buffer before giving random garbage to the SCU
Fix stack buffer size for IPC writev messages
intel_scu_ipc: Use the new cpu identification function
intel_scu_ipc: tidy up unused bits
Remove indirect read write api support.
intel_scu_ipc: Support Medfield processors
intel_scu_ipc: detect CPU type automatically
x86 plat: limit x86 platform driver menu to X86
acpi ec_sys: Be more cautious about ec write access
acpi ec: Fix possible double io port registration
hp-wmi: acpi_drivers.h is already included through acpi.h two lines below
hp-wmi: Fix mixing up of and/or directive
dell-laptop: make dell_laptop_i8042_filter() static
asus-laptop: fix asus_input_init error path
msi-wmi: make needlessly global symbols static
...
