Support for m88rs2000 chip used in lmedm04 driver.
Note there are still lock problems.
Slow channel change due to the large block of registers sent in set_frontend.
Version 2 differences.
Front end is completely shut down when in sleep mode. This allow user to regain
control of device.
Kaffeine scan problem solved by removing register calls from get_frontend.
Kaffeine seems to call get_frontend when updating signal data. This can happen
in the middle of a tune stalling the driver.
Change calculations to those in the DS3000 driver.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These were in the original lme2510 device driver.
Removing them significantly speeds up the driver.
All tuners tested.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In CDRXD(), Negative number is assigned to unsigned variable
'state->noise_cal.tdCal2.
Members of 'SNoiseCal' should be 'signed short'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DibAcquireLock() is implemented as mutex_lock_interruptible()
but the driver does not handle unsuccessful locking.
As a result it may lead to unlock of an unheld mutex.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several error paths, where &state->platform.risc.mem_mbx_lock
is not unlocked. The patch fixes it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add CI support to az6007 driver.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current delay of 30uS is too short to recover any carrier.
In the lmedm04 driver delays were added to overcome carrier lock
problems. The typical delay was 30mS (2 x 15ms register write
0x2c and read 0x24).
Other drivers that use STV0288 don't appear to have any delay are
likely to have also suffered this problem.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
When reading IF_AGC_GAIN register a wrong value for the base address
register was used (STB0899_DEMOD instead of STB0899_S2DEMOD). That
lead to a wrong signal strength value on DVB-S2 transponders.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_read_status the FE_HAS_SIGNAL flag was not set in case of a
successful carrier lock. This change fixes that.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b2a29b578d sets accidentally
supported delivery systems as DVB-T/T2 whilst it should be
DVB-S/S2. Due to that frontend cannot be used at all.
Reported-by: Jiří Zelenka <klacek@bubakov.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
"For 4 fixes for 3.3 (all trivial):
- uvc video driver: fixes a division by zero;
- davinci: add module.h to fix compilation;
- smsusb: fix the delivery system setting;
- smsdvb: the get_frontend implementation there is broken.
The smsdvb patch has 127 lines, but it is trivial: instead of
returning a cache of the set_frontend (with is wrong, as it doesn't
have the updated values for the data, and the implementation there is
buggy), it copies the information of the detected DVB parameters from
the smsdvb private structures into the corresponding DVBv5 struct
fields."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] smsdvb: fix get_frontend
[media] smsusb: fix the default delivery system setting
[media] media: davinci: added module.h to resolve unresolved macros
[media] [FOR,v3.3] uvcvideo: Avoid division by 0 in timestamp calculation
Besides sticks with the usb id 14AA:0160, there exists also some
with 14AA:0161 - this is the output in /var/log/messages:
usb 1-1: new high-speed USB device number 2 using ehci_hcd
usb 1-1: New USB device found, idVendor=14aa, idProduct=0161
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: Freecom DVB-T
usb 1-1: Manufacturer: Freecom DVB-T
usb 1-1: SerialNumber: 00000000000036742
The patch is based on the code at
http://git.linuxtv.org/anttip/media_tree.git/shortlog/refs/heads/realtek
Signed-off-by: Paolo Pantò <munix9@googlemail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the get_frontend function, an internal copy of the dtv_frontend_properties
struct (which is never initialized) is copied over the frontend property cache
data structure, resetting everything to 0.
In particular, the delivery system is reset to 0 (which is an invalid value)
so the driver stops working as soon as a DVBv3 application calls the
get_frontend function, giving this error:
dvb_frontend_ioctl_legacy: doesn't know how to handle a DVBv3 call to delivery
system 0
This patch eliminates the unused internal copy of the dtv_frontend_properties
struct, and gives a proper implementation of the get_frontend function.
The original author of the patch is Panagiotis Malakoudis, who also tested
this new version on Ubuntu 11.10 with the latest media_build tree installed.
The original patch has been used on MIPS set-top-boxes for over one year,
but it was never posted on the linux-media list.
I ported the code to the current media_build tree (converting it to use the
dtv_frontend_properties struct) and added basic support for ISDB-T (untested).
Signed-off-by: Panagiotis Malakoudis <malakudi@gmail.com>
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error handling in lgdt3303_read_status() and lgdt330x_read_ucblocks()
doesn't work, because i2c_read_demod_bytes() returns a u8 and (err < 0)
is always false.
err = i2c_read_demod_bytes(state, 0x58, buf, 1);
if (err < 0)
return err;
Change the return type of i2c_read_demod_bytes() to int. Also change
the return value on error to -EIO to make (err < 0) work.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The signal strength value returned is not quite correct, it decreases
when I increase the gain of my antenna, and vice versa. It also
doesn't span over the whole 0x0000-0xffff range. Compute a value which
at least increases when signal strength increases, and spans the whole
allowed range.
In practice I get 67% with my antenna fully amplified and 51% with
no amplification. This is close enough to what I get on my other
DVB-T adapter with the same antenna.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read signal strength using VAR_P_INBAND and apply FEC preferred values.
Note this does not work on IT9137 devices even with dvb-usb-it9135-01.fw
firmware.
Config read_sl allows switch between read signal strength and signal
level.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow PID 8192 to turn PID filter off in USB high speed.
The PID number is still written to the PID index and will only
turn on again if that index is set to 0.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some virtual I2C commands are missed along some PID filtering
commands resulting complete stall of driver.
Since dvb-usb cannot handle the -EAGAIN error and commands
generally should not be missed mutex_lock is used instead.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the drivers in drivers/media/* to use the
module_i2_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Heungjun Kim <riverful.kim@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Johannes Obermaier <johannes.obermaier@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Il 29/02/2012 22:30, Geert Uytterhoeven ha scritto:
> http://kisskb.ellerman.id.au/kisskb/buildresult/5759200/ ERROR:
> "__udivdi3" [drivers/media/dvb/frontends/rtl2830.ko] undefined!
>
The following patch fixed the warning on my 32 bit system.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two issues on the default delivery system setting for smsusb:
1) instead of filling the delivery system for the per-client
frontend.ops, it were changing the global structure;
2) The client->frontend.ops copy were keeping the previous value
of the template. So, the first time the device was inserted,
it was using the wrong value.
Reported-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is not accessible when device is sleeping.
Preventing such IOCTLs when sleep should be job of DVB CORE...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* some style issues
* remove rtl2832u device IDs
* move USB IDs to correct place
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement I2C functionality according to real RTL2830 demod.
Do not send register page in first byte of each I2C write, instead
use logic to set page using own write when needed. Page register is
physical register 0 as generally used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not return error for demod attach in case of mxl5005s tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For now it supports only Realtek RTL2831U chip.
RTL2831U is integrated DVB USB interface and DVB-T demod.
DVB-T demod integrated to RTL2831U is Realtek RTL2830.
Supported tuners are QT1010, MT2060 and MXL5005S.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[mchehab@redhat.com: fix a small typo]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Problems with the PID setting stalling demux on applications like VDR and MythTV.
The PID filter is now defaulted to OFF.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 7e07222 breaks DVBFE_ALGO_HW tuning after a retune is requested,
which causes bad tuning on my TBS 6920.
[ 0.769091] pci 0000:06:00.0: [14f1:8852] type 0 class 0x000400
[ 19.733530] CORE cx23885[0]: subsystem: 6920:8888, board: TurboSight TBS 6920 [card=14,autodetected]
[ 762.824912] cx24116_load_firmware: FW version 1.23.86.1
7e0722215a [media] dvb-core: Don't pass DVBv3 parameters on tune() fops
Although re_tune is set to true when FESTATE_RETUNE occurs, it is never
set back to false which the old code used to do when !FESTATE_RETUNE.
This patch sets re_tune to false if !(state & FESTATE_RETUNE).
$ szap-s2 -a 2 "Channel 5"
reading channels from file '/home/simon/.szap/channels.conf'
zapping to 247 'Channel 5':
delivery DVB-S, modulation QPSK
sat 0, frequency 10964 MHz H, symbolrate 22000000, coderate 5/6, rolloff 0.35
vpid 0x092a, apid 0x092b, sid 0x092d
using '/dev/dvb/adapter2/frontend0' and '/dev/dvb/adapter2/demux0'
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eb33 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for different types of remote.
ITE remotes share common device IDs with differently assigned keys.
Two versions of remote maps have been created there are likely to be more.
v1 for all other IDs
v2 for USB_PID_ITETECH_IT9135_9005.
This patch also separates the configuration parts from it913x_identify_state function.
TODO
remotes for HID interfaces.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx18 and ddbridge drivers include linux/dvb/audio.h and video.h
without using them.
Remove those includes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some version 2 devices have different tuner IDs. ID 0x38
appears to have weak signal strength.
Apply default 0x60 to unknown IDs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control message load increased heavily after CI/CAM support due
to dvb_ca_en50221. It looks like CI/CAM drops to non-working
state easily after error is returned to its callbacks. Due to
that, add some logic to avoid errors repeating failed messages.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced by multi-frontend to single-frontend change.
It is safer to put DVB-T parts sleeping when auto-switching to DVB-T2
and vice versa. That was original behaviour.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
