HCI_CONN_FLAG_REMOTE_WAKEUP can only be set if device can be programmed
in the allowlist which in case of device using RPA requires LL Privacy
support to be enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215768
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending WMT command during the reset in progress is invalid and would get
no response from firmware until the reset is complete, so we ignore the WMT
command here to resolve the issue which causes the whole reset process
taking too long.
Fixes: 8fafe70225 ("Bluetooth: mt7921s: support bluetooth reset mechanism")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to FW advised sequence, mt7921s need to re-acquire privilege
immediately after the firmware download is complete before normal running.
Otherwise, it is still possible the bus may be stuck in an abnormal status
that causes FW initialization failure in the current driver.
Fixes: 752aea5848 ("Bluetooth: mt7921s: fix bus hang with wrong privilege")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the device ID for the BCM4373A0 module, found e.g. in
the Infineon (Cypress) CYW4373E chip. The required firmware file is
named 'BCM4373A0.hcd'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move power_on work cancel to hci_dev_close_sync to ensure that power_on
work is canceled after HCI interface down, power off, rfkill, etc.
For example, if
hciconfig hci0 down
is done early enough during boot, it may run before power_on work.
Then, power_on work will actually bring up interface despite above
hciconfig command.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Concurrent operations from events on le_{accept,resolv}_list are
currently unprotected by hdev->lock.
Most existing code do already protect the lists with that lock.
This can be observed in hci_debugfs and hci_sync.
Add the protection for these events too.
Fixes: b950aa8863 ("Bluetooth: Add definitions and track LE resolve list modification")
Fixes: 0f36b589e4 ("Bluetooth: Track LE white list modification via HCI commands")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All accesses (both reads and modifications) to
hdev->{accept,reject}_list are protected by hdev lock,
except the ones in hci_conn_request_evt. This can cause a race
condition in the form of a list corruption.
The solution is to protect these lists in hci_conn_request_evt as well.
I was unable to find the exact commit that introduced the issue for the
reject list, I was only able to find it for the accept list.
Fixes: a55bd29d52 ("Bluetooth: Add white list lookup for incoming connection requests")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_is_adv_monitoring's function documentation states that it must be
called under the hdev lock. Paths that leads to an unlocked call are:
discov_update => start_discovery => interleaved_discov => active_scan
and: discov_update => start_discovery => active_scan
The solution is to take the lock in active_scan during the duration of
the call to hci_is_adv_monitoring.
Fixes: c32d624640 ("Bluetooth: disable filter dup when scan for adv monitor")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the support for RTL8852C BT controller on USB interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCA controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This prints warnings for controllers setting broken quirks to increase
their visibility and warn about broken controllers firmware that
probably needs updates to behave properly.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While looking at a crash report on a timer list being corrupted, which
usually happens when a timer is freed while still active. This is
commonly triggered by code calling del_timer() instead of
del_timer_sync() just before freeing.
One possible culprit is the hci_qca driver, which does exactly that.
Eric mentioned that wake_retrans_timer could be rearmed via the work
queue, so also move the destruction of the work queue before
del_timer_sync().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The only usage of regmap_ibt is to (after the regmap_init() macro is
expanded), pass its address to __regmap_init(), which takes a pointer to
const struct regmap_bus as input. Make it const to allow the compiler to
put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Small change to add new commands to tail of the list, and find/remove them
from the head of the list.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Connecting the same socket twice consecutively in sco_sock_connect()
could lead to a race condition where two sco_conn objects are created
but only one is associated with the socket. If the socket is closed
before the SCO connection is established, the timer associated with the
dangling sco_conn object won't be canceled. As the sock object is being
freed, the use-after-free problem happens when the timer callback
function sco_sock_timeout() accesses the socket. Here's the call trace:
dump_stack+0x107/0x163
? refcount_inc+0x1c/
print_address_description.constprop.0+0x1c/0x47e
? refcount_inc+0x1c/0x7b
kasan_report+0x13a/0x173
? refcount_inc+0x1c/0x7b
check_memory_region+0x132/0x139
refcount_inc+0x1c/0x7b
sco_sock_timeout+0xb2/0x1ba
process_one_work+0x739/0xbd1
? cancel_delayed_work+0x13f/0x13f
? __raw_spin_lock_init+0xf0/0xf0
? to_kthread+0x59/0x85
worker_thread+0x593/0x70e
kthread+0x346/0x35a
? drain_workqueue+0x31a/0x31a
? kthread_bind+0x4b/0x4b
ret_from_fork+0x1f/0x30
Link: https://syzkaller.appspot.com/bug?extid=2bef95d3ab4daa10155b
Reported-by: syzbot+2bef95d3ab4daa10155b@syzkaller.appspotmail.com
Fixes: e1dee2c1de ("Bluetooth: fix repeated calls to sco_sock_kill")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the incorrect pointer check on ven_data.
Fixes: f41b91fa17 ("Bluetooth: mt7921s: Add .btmtk_get_codec_config_data")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are provedly different firmware variants for the different
phones using some of these chips. These were extracted from a few
Samsung phones:
37446 BCM4334B0.samsung,codina-tmo.hcd
37366 BCM4334B0.samsung,golden.hcd
37403 BCM4334B0.samsung,kyle.hcd
37366 BCM4334B0.samsung,skomer.hcd
This patch supports the above naming schedule with inserting
[.board_name] between the firmware name and ".hcd". This scheme
is the same as used by the companion BRCM wireless chips
as can be seen in
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
or just by looking at the firmwares in linux-firmware/brcm.
Currently we only support board variants using the device
tree compatible string as board type, but other schemes are
possible.
This makes it possible to successfully load a few unique
firmware variants for some Samsung phones.
Cc: phone-devel@vger.kernel.org
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rarely some of the test cases fail. Make the test more robust by increasing
the timeout of ping commands to 5 seconds.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Wunner says:
====================
Polling be gone on LAN95xx
Do away with link status polling on LAN95xx USB Ethernet
and rely on interrupts instead, thereby reducing bus traffic,
CPU overhead and improving interface bringup latency.
Link to v2:
https://lore.kernel.org/netdev/cover.1651574194.git.lukas@wunner.de/
Only change since v2:
* Patch [5/7]:
* Drop call to __irq_enter_raw() which worked around a warning in
generic_handle_domain_irq(). That warning is gone since
792ea6a074 (queued on tip.git/irq/urgent).
(Marc Zyngier, Thomas Gleixner)
====================
If reading the Interrupt Source Flag register fails with -ENODEV, then
the PHY has been hot-removed and the correct response is to bail out
instead of throwing a WARN splat and attempting to suspend the PHY.
The PHY should be stopped in due course anyway as the kernel
asynchronously tears down the device.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache the interrupt mask to avoid re-reading it from the PHY upon every
interrupt.
This will simplify a subsequent commit which detects hot-removal in the
interrupt handler and bails out.
Analyzing and debugging PHY transactions also becomes simpler if such
redundant reads are avoided.
Last not least, interrupt overhead and latency is slightly improved.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link status of SMSC LAN95xx chips is polled once per second, even though
they're capable of signaling PHY interrupts through the MAC layer.
Forward those interrupts to the PHY driver to avoid polling. Benefits
are reduced bus traffic, reduced CPU overhead and quicker interface
bringup.
Polling was introduced in 2016 by commit d69d169493 ("usbnet:
smsc95xx: fix link detection for disabled autonegotiation").
Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt,
hence couldn't detect link-up events when auto-negotiation was disabled.
The proper solution would have been to enable the ENERGYON interrupt
instead of polling.
Since then, PHY handling was moved from the LAN95xx driver to the SMSC
PHY driver with commit 05b35e7eb9 ("smsc95xx: add phylib support").
That PHY driver is capable of link detection with auto-negotiation
disabled because it enables the ENERGYON interrupt.
Note that signaling interrupts through the MAC layer not only works with
the integrated PHY, but also with an external PHY, provided its
interrupt pin is attached to LAN95xx's nPHY_INT pin.
In the unlikely event that the interrupt pin of an external PHY is
attached to a GPIO of the SoC (or not connected at all), the driver can
be amended to retrieve the irq from the PHY's of_node.
To forward PHY interrupts to phylib, it is not sufficient to call
phy_mac_interrupt(). Instead, the PHY's interrupt handler needs to run
so that PHY interrupts are cleared. That's because according to page
119 of the LAN950x datasheet, "The source of this interrupt is a level.
The interrupt persists until it is cleared in the PHY."
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Therefore, create an IRQ domain with a single IRQ for the PHY. In the
future, the IRQ domain may be extended to support the 11 GPIOs on the
LAN95xx.
Normally the PHY interrupt should be masked until the PHY driver has
cleared it. However masking requires a (sleeping) USB transaction and
interrupts are received in (non-sleepable) softirq context. I decided
not to mask the interrupt at all (by using the dummy_irq_chip's noop
->irq_mask() callback): The USB interrupt endpoint is polled in 1 msec
intervals and normally that's sufficient to wake the PHY driver's IRQ
thread and have it clear the interrupt. If it does take longer, worst
thing that can happen is the IRQ thread is woken again. No big deal.
Because PHY interrupts are now perpetually enabled, there's no need to
selectively enable them on suspend. So remove all invocations of
smsc95xx_enable_phy_wakeup_interrupts().
In smsc95xx_resume(), move the call of phy_init_hw() before
usbnet_resume() (which restarts the status URB) to ensure that the PHY
is fully initialized when an interrupt is handled.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch> # from a PHY perspective
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the
MAC full duplex mode and PHY flow control registers based on cached data
in struct phy_device:
smsc95xx_status() # raises EVENT_LINK_RESET
usbnet_deferred_kevent()
smsc95xx_link_reset() # uses cached data in phydev
Simultaneously, phylib polls link status once per second and updates
that cached data:
phy_state_machine()
phy_check_link_status()
phy_read_status()
lan87xx_read_status()
genphy_read_status() # updates cached data in phydev
If smsc95xx_link_reset() wins the race against genphy_read_status(),
the registers may be updated based on stale data.
E.g. if the link was previously down, phydev->duplex is set to
DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even
though genphy_read_status() may update it to DUPLEX_FULL afterwards.
PHY interrupts are currently only enabled on suspend to trigger wakeup,
so the impact of the race is limited, but we're about to enable them
perpetually.
Avoid the race by delaying execution of smsc95xx_link_reset() until
phy_state_machine() has done its job and calls back via
smsc95xx_handle_link_change().
Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib
picks up link status changes through polling. So drop the declaration
of a ->link_reset() callback.
Note that the semicolon on a line by itself added in smsc95xx_status()
is a placeholder for a function call which will be added in a subsequent
commit. That function call will actually handle the INT_ENP_PHY_INT_
interrupt.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc95xx_reset() resets the PHY behind the PHY driver's back, which
seems like a bad idea generally. Remove that portion of the function.
We're about to use PHY interrupts instead of polling to detect link
changes on SMSC LAN95xx chips. Because smsc95xx_reset() is called from
usbnet_open(), PHY interrupt settings are lost whenever the net_device
is brought up.
There are two other callers of smsc95xx_reset(), namely smsc95xx_bind()
and smsc95xx_reset_resume(), and both may indeed benefit from a PHY
reset. However they already perform one through their calls to
phy_connect_direct() and phy_init_hw().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Gabriel Hojda <ghojda@yo2urs.ro>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver
attempts to clear the signaled interrupts by writing "all ones" to the
Interrupt Status Register.
However the driver only ever enables a single type of interrupt, namely
the PHY Interrupt. And according to page 119 of the LAN950x datasheet,
its bit in the Interrupt Status Register is read-only. There's no other
way to clear it than in a separate PHY register:
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Consequently, writing "all ones" to the Interrupt Status Register is
pointless and can be dropped.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c9d6c2b87 ("usbnet: run unbind() before unregister_netdev()")
sought to fix a use-after-free on disconnect of USB Ethernet adapters.
It turns out that a different fix is necessary to address the issue:
https://lore.kernel.org/netdev/18b3541e5372bc9b9fc733d422f4e698c089077c.1650177997.git.lukas@wunner.de/
So the commit was not necessary.
The commit made binding and unbinding of USB Ethernet asymmetrical:
Before, usbnet_probe() first invoked the ->bind() callback and then
register_netdev(). usbnet_disconnect() mirrored that by first invoking
unregister_netdev() and then ->unbind().
Since the commit, the order in usbnet_disconnect() is reversed and no
longer mirrors usbnet_probe().
One consequence is that a PHY disconnected (and stopped) in ->unbind()
is afterwards stopped once more by unregister_netdev() as it closes the
netdev before unregistering. That necessitates a contortion in ->stop()
because the PHY may only be stopped if it hasn't already been
disconnected.
Reverting the commit allows making the call to phy_stop() unconditional
in ->stop().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically.
./drivers/net/ethernet/sunplus/spl2sw_driver.c:569:3-8: No need to set
.owner here. The core will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently If use page pool allocation stats to analysis a RX performance
degradation problem. These stats only count for pages allocate from
page_pool_alloc_pages. But nic drivers such as hns3 use
page_pool_dev_alloc_frag to allocate pages, so page stats in this API
should also be counted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the following coccicheck warning:
./drivers/net/ethernet/sunplus/spl2sw_driver.c:217:27-28: WARNING
opportunity for swap().
./drivers/net/ethernet/sunplus/spl2sw_driver.c:222:27-28: WARNING
opportunity for swap().
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau says:
====================
net: inet: Retire port only listening_hash
This series is to retire the port only listening_hash.
The listen sk is currently stored in two hash tables,
listening_hash (hashed by port) and lhash2 (hashed by port and address).
After commit 0ee58dad5b ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f643 ("net: tcp: prefer listeners bound to an address"),
the TCP-SYN lookup fast path does not use listening_hash.
The commit 05c0b35709 ("tcp: seq_file: Replace listening_hash with lhash2")
also moved the seq_file (/proc/net/tcp) iteration usage from
listening_hash to lhash2.
There are still a few listening_hash usages left.
One of them is inet_reuseport_add_sock() which uses the listening_hash
to search a listen sk during the listen() system call. This turns
out to be very slow on use cases that listen on many different
VIPs at a popular port (e.g. 443). [ On top of the slowness in
adding to the tail in the IPv6 case ]. A latter patch has a
selftest to demonstrate this case.
This series takes this chance to move all remaining listening_hash
usages to lhash2 and then retire listening_hash.
====================
Link: https://lore.kernel.org/r/20220512000546.188616-1-kafai@fb.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a test that has 300 VIPs listening on port 443.
Each VIP:443 will have 80 listening socks by using SO_REUSEPORT.
Thus, it will have 24000 listening socks.
Before removing the port only listening_hash, all socks will be in the
same port 443 bucket and inet_reuseport_add_sock() spends much time to
walk through the bucket. After removing the port only listening_hash
and move all usage to the port+addr lhash2, each bucket in the
ideal case has 80 sk which is much smaller than before.
Here is the test result from a qemu:
Before: listen 24000 socks took 210.210485362 (~210s)
After: listen 24000 socks took 0.207173 (~210ms)
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The listen sk is currently stored in two hash tables,
listening_hash (hashed by port) and lhash2 (hashed by port and address).
After commit 0ee58dad5b ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f643 ("net: tcp: prefer listeners bound to an address"),
the TCP-SYN lookup fast path does not use listening_hash.
The commit 05c0b35709 ("tcp: seq_file: Replace listening_hash with lhash2")
also moved the seq_file (/proc/net/tcp) iteration usage from
listening_hash to lhash2.
There are still a few listening_hash usages left.
One of them is inet_reuseport_add_sock() which uses the listening_hash
to search a listen sk during the listen() system call. This turns
out to be very slow on use cases that listen on many different
VIPs at a popular port (e.g. 443). [ On top of the slowness in
adding to the tail in the IPv6 case ]. The latter patch has a
selftest to demonstrate this case.
This patch takes this chance to move all remaining listening_hash
usages to lhash2 and then retire listening_hash.
Since most changes need to be done together, it is hard to cut
the listening_hash to lhash2 switch into small patches. The
changes in this patch is highlighted here for the review
purpose.
1. Because of the listening_hash removal, lhash2 can use the
sk->sk_nulls_node instead of the icsk->icsk_listen_portaddr_node.
This will also keep the sk_unhashed() check to work as is
after stop adding sk to listening_hash.
The union is removed from inet_listen_hashbucket because
only nulls_head is needed.
2. icsk->icsk_listen_portaddr_node and its helpers are removed.
3. The current lhash2 users needs to iterate with sk_nulls_node
instead of icsk_listen_portaddr_node.
One case is in the inet[6]_lhash2_lookup().
Another case is the seq_file iterator in tcp_ipv4.c.
One thing to note is sk_nulls_next() is needed
because the old inet_lhash2_for_each_icsk_continue()
does a "next" first before iterating.
4. Move the remaining listening_hash usage to lhash2
inet_reuseport_add_sock() which this series is
trying to improve.
inet_diag.c and mptcp_diag.c are the final two
remaining use cases and is moved to lhash2 now also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch folds lhash2 related functions into __inet_hash and
inet_unhash. This will make the removal of the listening_hash
in a latter patch easier to review.
First, this patch folds inet_hash2 into __inet_hash.
For unhash, the current call sequence is like
inet_unhash() => __inet_unhash() => inet_unhash2().
The specific testing cases in __inet_unhash() are mostly related
to TCP_LISTEN sk and its caller inet_unhash() already has
the TCP_LISTEN test, so this patch folds both __inet_unhash() and
inet_unhash2() into inet_unhash().
Note that all listening_hash users also have lhash2 initialized,
so the !h->lhash2 check is no longer needed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0ee58dad5b ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f643 ("net: tcp: prefer listeners bound to an address"),
the count is no longer used. This patch removes it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin Habets says:
====================
Make sfc-siena.ko specific to Siena
This series is a follow-up to the one titled "Move Siena into
a separate subdirectory".
It enhances the new sfc-siena.ko module to differentiate it from sfc.ko.
Patches
Patches 1-5 create separate Kconfig options for Siena, and adjusts the
various names used for work items and directories.
Patch 6 reinstates SRIOV functionality in sfc-siena.ko.
Testing
Various build tests were done such as allyesconfig, W=1 and sparse.
The new sfc-siena.ko and sfc.ko modules were tested on a machine with NICs
for both modules in them.
Inserting the updated sfc.ko and the new sfc-siena.ko modules at the same
time works, and no work items and directories exist with the same name.
====================
Link: https://lore.kernel.org/r/165228589518.696.7119477411428288875.stgit@palantir17.mph.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
They were removed in the first series since they were not used for EF10.
Put that code back for Siena, with the prototypes in siena_sriov.h
since that file is a more applicable place for it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change the clock name and work queue names to differentiate them from
the names used in sfc.ko.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a Siena Kconfig option and use it in stead of the sfc one.
Rename the internal variable for the 'mcdi_logging_default' module
parameter to avoid a naming conflict with the one in sfc.ko.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a Siena Kconfig option and use it in stead of the sfc one.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a Siena Kconfig option and use it in stead of the sfc one.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a Siena Kconfig option and use it in stead of the sfc one.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Restructure struct ocelot_port
This patch set represents preparation for further work. It adds an
"index" field to struct ocelot_port, and populates it from the Felix DSA
driver and Ocelot switchdev driver.
The users of struct ocelot_port :: index are the same users as those of
struct ocelot_port_private :: chip_port.
====================
Link: https://lore.kernel.org/r/20220511100637.568950-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
