One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for reading and reporting the 10G link status on the
88e6390 in addition to the 1000BASE-X/2500BASE-X/SGMII status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private MV88E6390_PCS_CONTROL_1 definitions in serdes.h reflects
the IEEE 802.3 standard PCS control register 1 definitions, only
offset by 0x1000 in the PHYXS register space. Rather than inventing
our own, use those that already exist, and name the register
MV88E6390_10G_CTRL1.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d1cbfd771c ("ptp_clock: Allow for it to be optional") changed
all PTP-capable Ethernet drivers from `select PTP_1588_CLOCK` to `imply
PTP_1588_CLOCK`, "in order to break the hard dependency between the PTP
clock subsystem and ethernet drivers capable of being clock providers."
As a result it is possible to build PTP-capable Ethernet drivers without
the PTP subsystem by deselecting PTP_1588_CLOCK. Drivers are required to
handle the missing dependency gracefully.
Some PTP-capable Ethernet drivers (e.g., TI_CPSW) factor their PTP code
out into separate drivers (e.g., TI_CPTS_MOD). The above commit also
changed these PTP-specific drivers to `imply PTP_1588_CLOCK`, making it
possible to build them without the PTP subsystem. But as Grygorii
Strashko noted in [1]:
On Wed, Apr 22, 2020 at 02:16:11PM +0300, Grygorii Strashko wrote:
> Another question is that CPTS completely nonfunctional in this case and
> it was never expected that somebody will even try to use/run such
> configuration (except for random build purposes).
In my view, enabling a PTP-specific driver without the PTP subsystem is
a configuration error made possible by the above commit. Kconfig should
not allow users to create a configuration with missing dependencies that
results in "completely nonfunctional" drivers.
I audited all network drivers that call ptp_clock_register() but merely
`imply PTP_1588_CLOCK` and found five PTP-specific drivers that are
likely nonfunctional without PTP_1588_CLOCK:
NET_DSA_MV88E6XXX_PTP
NET_DSA_SJA1105_PTP
MACB_USE_HWSTAMP
CAVIUM_PTP
TI_CPTS_MOD
Note how these symbols all reference PTP or timestamping in their name;
this is a clue that they depend on PTP_1588_CLOCK.
Change them from `imply PTP_1588_CLOCK` [2] to `depends on PTP_1588_CLOCK`.
I'm not using `select PTP_1588_CLOCK` here because PTP_1588_CLOCK has
its own dependencies, which `select` would not transitively apply.
Additionally, remove the `select NET_PTP_CLASSIFY` from CPTS_TI_MOD;
PTP_1588_CLOCK already selects that.
[1]: https://lore.kernel.org/lkml/c04458ed-29ee-1797-3a11-7f3f560553e6@ti.com/
[2]: NET_DSA_SJA1105_PTP had never declared any type of dependency on
PTP_1588_CLOCK (`imply` or otherwise); adding a `depends on PTP_1588_CLOCK`
here seems appropriate.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d1cbfd771c ("ptp_clock: Allow for it to be optional")
Signed-off-by: Clay McClure <clay@daemons.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These struct members named 'phylink_validate' was assigned twice:
static const struct mv88e6xxx_ops mv88e6190_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6190x_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390x_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6191_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6290_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
Remove all the first one and leave the second one which are been used in
fact. Be aware that for 'mv88e6190x_ops' the assignment functions is
different while the others are all the same. This fixes the following
coccicheck warning:
drivers/net/dsa/mv88e6xxx/chip.c:3911:48-49: phylink_validate: first
occurrence line 3965, second occurrence line 3967
drivers/net/dsa/mv88e6xxx/chip.c:3970:49-50: phylink_validate: first
occurrence line 4024, second occurrence line 4026
drivers/net/dsa/mv88e6xxx/chip.c:4029:48-49: phylink_validate: first
occurrence line 4082, second occurrence line 4085
drivers/net/dsa/mv88e6xxx/chip.c:4184:48-49: phylink_validate: first
occurrence line 4238, second occurrence line 4242
Fixes: 4262c38dc4 ("net: dsa: mv88e6xxx: Add SERDES stats counters to all 6390 family members")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.
Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.
Fixes: 30c4a5b0aa ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the status of the PHY_DETECT bit to determine whether we need to
force the MAC settings in mac_link_up() and mac_link_down().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_link_state method is only used by mv88e6xxx_port_setup_mac(),
which is now only called during port setup, rather than also being
called via phylink's mac_config method.
Remove this now unnecessary optimisation, which allows us to remove the
port_link_state methods as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the speed independently of duplex makes little sense; the two
parameters result from negotiation or fixed setup, and may have inter-
dependencies. Moreover, they are always controlled via the same
register - having them split means we have to read-modify-write this
register twice.
Combine the two operations into a single port_set_speed_duplex()
operation. Not only is this more efficient, it reduces the size of the
code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_mac_change() is supposed to be called with a 'false' argument
if the link has gone down since it was last reported up; this is to
ensure that link events along with renegotiation events are always
correctly reported to userspace.
Read the BMSR once when we have an interrupt, and report the link
latched status to phylink via phylink_mac_change(). phylink will deal
automatically with re-reading the link state once it has processed the
link-down event.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which
handle the PCS layer of such links.
- Implement phylink PCS link state reading, so that we can provide
ethtool with the linkmodes and link speed in the expected manner.
Note: this will only be called for in-band negotiation, which is
only supported by the serdes interfaces.
- Implement phylink PCS configuration, so that the in-band AN and
advertisement can be configured.
- Implement phylink PCS negotiation restart, so that the in-band AN
can be restarted.
- Implement phylink PCS link up, so that when operating out-of-band,
the Serdes can be configured for the appropriate fixed speed mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only configure the interface settings in mac_config(), leaving the
speed and duplex settings to mac_link_up to deal with.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SGMII/1000base-X serdes register set is a clause 22 register set
offset at 0x2000 in the PHYXS device. Rather than inventing our own
defintions, use those that already exist, and name the register
MV88E6390_SGMII_BMCR. Also remove the unused MV88E6390_SGMII_STATUS
definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7df ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the switch is not hardware reset on a warm boot, interrupts can be
left enabled, and possibly pending. This will cause us to enter an
infinite loop trying to service an interrupt we are unable to handle,
thereby preventing the kernel from booting.
Ensure that the global 2 interrupt sources are disabled before we claim
the parent interrupt.
Observed on the ZII development revision B and C platforms with
reworked serdes support, and using reboot -f to reboot the platform.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing ~ to the usage of the mask.
Reported-by: Kevin Benson <Kevin.Benson@zii.aero>
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 5c74c54ce6 ("net: dsa: mv88e6xxx: Split monitor port configuration")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the resolved link configuration to set the MAC configuration when
mac_link_up() for non-internal-PHY ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting VLANs on DSA switches, the VLAN is added to both the port
concerned as well as the CPU port by dsa_slave_vlan_add(), as well as
any DSA ports. If multiple ports are configured with the same VLAN ID,
this triggers a warning on the CPU and DSA ports.
Avoid this warning for CPU and DSA ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has upto 8 sets of PCS registers, depending on how ports
9 and 10 are configured. The can be spread over 8 ports. If a port has
a PCS register set, return it along with the port registers. The
register space is sparse, so hard code a list of registers which will
be returned. It can later be extended, if needed, by append to the end
of the list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352 has one PCS which can be used for 1000BaseX or
SGMII. Add the registers to the dump for the port which the PCS is
associated to.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool provides a generic mechanism for a driver to return the
registers of an ethernet device. DSA uses this to give the port
registers associated with an interfaces. Extend this to allow PCS
registers to also be returned, if the port has a PCS associated to it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.
Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 3095383a8a ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique interrupt name for the VTU and ATU,
based on the device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique g2 interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique watchdog interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:
95: 3 mv88e6xxx-g2 9 Edge mv88e6xxx-0.2:00-serdes-9
96: 0 mv88e6xxx-g2 10 Edge mv88e6xxx-0.2:00-serdes-10
The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a6 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet checker is enabled in the serdes, then Rx counter registers
start working, and no side effects have been detected.
This patch enables packet checker automatically when powering serdes on,
and exposes Rx counter registers via ethtool statistics interface.
Code partially basded by older attempt by Andrew Lunn.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mv88e6xxx PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
For the record, the semantics of this driver are:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp rising edge
Cc: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a stray semicolon in an if statement that will cause a dev_err
message to be printed unconditionally. Fix this by removing the stray
semicolon.
Addresses-Coverity: ("Stay semicolon")
Fixes: f0942e00a1 ("net: dsa: mv88e6xxx: Add support for port mirroring")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.
It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.
Fixes: c5f299d592 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
