* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32: (40 commits)
unicore32: rewrite arch-specific tlb.h to use asm-generic version
unicore32: modify io_p2v and io_v2p macros, and adjust PKUNITY_mmio_BASEs
unicore32: replace unicore32-specific iomap functions with generic lib implementation
unicore32 machine related: add frame buffer driver for pkunity-v3 soc
unicore32 machine related files: add i2c bus drivers for pkunity-v3 soc
unicore32 io: redefine __REG(x) and re-use readl/writel funcs
unicore32 i8042 upgrade and bugfix: adjust resource request region type
unicore32 upgrade to v2.6.38-rc5: add one more paramter for pte_alloc_map call
unicore32 i8042: adjust io funcs of i8042-unicore32io.h
unicore32: rename PKUNITY_IOSPACE_BASE to PKUNITY_MMIO_BASE
unicore32: modify function names and parameters for irq_chips
unicore32: remove unused lines in arch/unicore32/include/asm/irq.h
unicore32 time.c: change calculate method for clock_event_device
unicore32: ADD MAINTAINER for unicore32 architecture
unicore32 machine related files: ps2 driver
unicore32 machine related files: pci bus handling
unicore32 machine related files: hardware registers
unicore32 machine related files: core files
unicore32 additional architecture files: boot process
unicore32 additional architecture files: low-level lib: misc
...
Acked-by: Arnd Bergmann <arnd@arndb.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fbdev: sh_mobile_lcdc: Add YUV framebuffer support
viafb: split pll configs up
viafb: remove duplicated clock storage
viafb: always return the best possible clock
viafb: remove duplicated clock information
fbdev: sh_mobile_lcdcfb: add backlight support
viafb: factor lcd scaling parameters out
viafb: strip some structures
viafb: remove unused data_mode and device_type
viafb: kill lcd_panel_id
video via: make local variables static
video via: fix iomem access
video/via: drop deprecated (and unused) i2c_adapter.id
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
change from original version -- by advice of Paul Mundt
1. remove videomemorysize definitions
2. remove unifb_enable and unifb_setup
3. use dev_warn instead of printk in fb driver
4. remove judgement for FB_ACCEL_PUV3_UNIGFX
5. adjust clk_get and clk_set_rate calls
6. add resources definitions
7. remove unifb_option
8. adjust register for platform_device
9. adjust unifb_ops position and unifb_regs assignment position
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Supports YCbCr420sp, YCbCr422sp, and YCbCr44sp, formats
(bpp = 12, 16, and 24) respectively.
When double-buffering both Y planes appear before the C planes (Y-Y-C-C),
as opposed to Y-C-Y-C.
Set .nonstd in struct sh_mobile_lcdc_chan_cfg to enable YUV mode, and use
.bpp to distiguish between the 3 modes.
The value of .nonstd is copied to bits 16-31 of LDDFR in the LCDC and
should be set accordingly.
.nonstd must be set to 0 for RGB mode.
Due to the encoding of YUV data, the framebuffer will clear to green
instead of black.
In YUV 420 mode, panning is only possible in 2 line increments.
Additionally in YUV 420 mode the vertical resolution of the framebuffer
must be an even number.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch splits the pll configs up on pll versions. This allows
easy adding of other known good pll values. Additionally it made it
possible to remove invalid configurations resulting in better
behaviour for such cases. The resulting clocks are no longer stored
resulting in some computing overhead on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The clocks can be easily recalculated by the timing and refresh value.
This brings us one step closer to removing VIAs modetable and use
generic ones and being easier extensible.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Before this patch only clocks that perfectly match were used and if
none existed this was not handled properly. This patch changes this
to always use the closest clock supported. This should behave like
before for clocks that have a perfect match but be much saner for
clocks which are slightly off.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the direct lookup table for resolution+refresh and
pixclock by calculating this information from the mode table. Removes a
lot of dupllication and error potential by just doing a little more
calculations on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Support for backlight devices controlled through board-specific
routines. Backlights can be defined per-channel and follow fbdev
directives to switch off as the LCD blanks or is turned on/off.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These parameters are the same for all currently known VIA IGPs so it
does not make any sense to store them with IGP specific data. This
saves a few bytes and helps a bit in dicovering the real differences.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes some write-only variables from the device management
structures. Just a small cleanup.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes all internal uses of another mostly artificial
value. It does duplicate the information of the maximum resolution and
it is not flexible as only a few resolutions exist. Hence it is better
to remove it and clean the mess up.
No runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Many local variables should be declared static.
Found by sparse, compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This driver is not respecting the iomem memory space restrictions
and does direct access. This works on x86 but is non-portable and
should not be done. Converted memcpy() of 2 to readw.
Last post increment of romptr was unnecessary since pointer never
used after that.
Found by sparse, compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Don't allow non panning updates to bypass the wait for the panel to turn on.
Signed-off-by: Carl Vanderlip <carlv@codeaurora.org>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
changes since v2:
- use v3 and v4 for specifying the ip version instead of i.MX23/28.
This is a better namespace when future versions are added.
- rename mach/fb.h to mach/mxsfb.h
changes since v1:
- Add a LCDC_ prefix to the register names.
- use set/clear registers where appropriate
- protect call to mxsfb_disable_controller() in mxsfb_remove()
with a (host->enabled) as suggested by Lothar Wassmann
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Netlink message processing in the kernel is synchronous these days,
capabilities can be checked directly in security_netlink_recv() from
the current process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Reviewed-by: James Morris <jmorris@namei.org>
[chrisw: update to include pohmelfs and uvesafb]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can then be tested by userspace to see if the capability is supported.
Userspace cannot rely on that value being left in var_screen, since userspace
itself can change it.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Carl Vanderlip <carlv@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This patch removes an assignment to the deprecated i2c_adapter.id
field. Since the field isn't used anywhere else in the driver it is
save to remove it.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Get rid of users of of_platform_driver in drivers/video. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide the framebuffer device with its correct parent (the PCI
device for PCI connected cards.) Also, use this struct device to
pass to sub-drivers rather than the pci_dev structure, which is
really what they want. Also propagate the assigned IRQ, which
they were getting direct from the PCI device structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than conditionally compiling out reg_b0_lock, always keep it
available, and always take it when changing the PLL rates.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add I2C support for the DDC bus to cyber2000fb driver. This is only bus
support, driver does not use EDID. Tested on two different CyberPro 2000
cards with i2cdetect and decode-edid.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
[removed i2c-id.h include - rmk]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The lowest closest multiplier/divisor combination should be used for
the PLL, not the largest. Reverse the search order.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With cmwq, there's no reason to use separate workqueues. Drop
msmfb_info->resume_workqueue and use system_wq instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: linux-usb@vger.kernel.org
Signed-off-by: David Brown <davidb@codeaurora.org>
Now vgacon_scrollback_startup() uses slab, not bootmem,
the comment above it is obsolete, so does __init_refok.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
lcd_device_register may return ERR_PTR, so a check is added for this value
before the dereference. All of the other changes reorganize the error
handling code in this function to avoid duplicating all of it in the added
case.
In the original code, in one case, the global variable fb_buffer was set to
NULL in error code that appears after this variable is initialized. This
is done now in all error handling code that has this property.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... return ERR_PTR(...); }
@@
identifier r.f, fld;
expression x;
statement S1,S2;
@@
x = f(...)
... when != IS_ERR(x)
(
if (IS_ERR(x) ||...) S1 else S2
|
*x->fld
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
