The FM10000 host interface can only support up to 184 bytes when
performing tunnel offloads. Because of this, a check was added to
prevent the driver from attempting to feed a header to the hardware too
big for it to parse. Make this check a little more robust by calculating
the inner L4 header length based on whether it is TCP or UDP.
Cc: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Fixes for sh_eth #4 v2
I'm continuing review and testing of Ethernet support on the R-Car H2
chip, with help from a colleague. This series fixes a few more issues.
These are not tested on any of the other supported chips.
v2: Add note that the revert is not a pure revert.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd9af07c34.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a translation problem in of_get_named_gpiod_flags()
- Fix a long standing container_of() mistake in the TPS65912
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5nhV
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes:
- Fix a translation problem in of_get_named_gpiod_flags()
- Fix a long standing container_of() mistake in the TPS65912 driver"
* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65912: fix wrong container_of arguments
gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- Several fixes in tmon tool.
- Fixes in intel int340x for _ART and _TRT tables.
- Add id for Avoton SoC into powerclamp driver.
- Fixes in RCAR thermal driver to remove race conditions and fix fail
path
- Fixes in TI thermal driver: removal of unnecessary code and build
fix if !CONFIG_PM_SLEEP
- Cleanups in exynos thermal driver
- Add stubs for include/linux/thermal.h. Now drivers using thermal
calls but that also work without CONFIG_THERMAL will be able to
compile for systems that don't care about thermal.
Note: I am sending this pull on Rui's behalf while he fixes issues in
his Linux box"
* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: int340x_thermal: Ignore missing _ART, _TRT tables
thermal/intel_powerclamp: add id for Avoton SoC
tools/thermal: tmon: silence 'set but not used' warnings
tools/thermal: tmon: use pkg-config to determine library dependencies
tools/thermal: tmon: support cross-compiling
tools/thermal: tmon: add .gitignore
tools/thermal: tmon: fixup tui windowing calculations
tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
tools/thermal: tmon: add min/max macros
tools/thermal: tmon: add --target-temp parameter
thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
thermal: rcar: Make error and remove paths symmetrical with init
thermal: rcar: Fix race condition between init and interrupt
thermal: Introduce dummy functions when thermal is not defined
ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
- fix a read-balance problem that was reported 2 years ago, but
that I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CaGN
-----END PGP SIGNATURE-----
Merge tag 'md/4.0-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three md fixes:
- fix a read-balance problem that was reported 2 years ago, but that
I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible"
* tag 'md/4.0-fixes' of git://neil.brown.name/md:
md: mark some attributes as pre-alloc
raid5: check faulty flag for array status during recovery.
md/raid1: fix read balance when a drive is write-mostly.
This is just a single patch to fix the KSTK_EIP() and KSTK_ESP() macros
for metag which have always been erronously returning the PC and stack
pointer of the task's kernel context rather than from its user context
saved at entry from userland into the kernel, which affects the contents
of /proc/<pid>/maps and /proc/<pid>/stat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1+sf
-----END PGP SIGNATURE-----
Merge tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fix from James Hogan:
"This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
macros for metag which have always been erronously returning the PC
and stack pointer of the task's kernel context rather than from its
user context saved at entry from userland into the kernel, which
affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"
* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix KSTK_EIP() and KSTK_ESP() macros
Eric W. Biederman says:
====================
Neighbour table and ax25 cleanups
While looking at the neighbour table to what it would take to allow
using next hops in a different address family than the current packets
I found a partial resolution for my issues and I stumbled upon some
work that makes the neighbour table code easier to understand and
maintain.
Long ago in a much younger kernel ax25 found a hack to use
dev_rebuild_header to transmit it's packets instead of going through
what today is ndo_start_xmit.
When the neighbour table was rewritten into it's current form the ax25
code was such a challenge that arp_broken_ops appeard in arp.c and
neigh_compat_output appeared in neighbour.c to keep the ax25 hack alive.
With a little bit of work I was able to remove some of the hack that
is the ax25 transmit path for ip packets and to isolate what remains
into a slightly more readable piece of code in ax25_ip.c. Removing the
need for the generic code to worry about ax25 special cases.
After cleaning up the old ax25 hacks I also performed a little bit of
work on neigh_resolve_output to remove the need for a dst entry and to
ensure cached headers get a deterministic protocol value in their cached
header. This guarantees that a cached header will not be different
depending on which protocol of packet is transmitted, and it allows
packets to be transmitted that don't have a dst entry. There remains
a small amount of code that takes advantage of when packets have a dst
entry but that is something different.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a dst helps a little bit for teql but is fundamentally
unnecessary and there are code paths where a dst is not available that
it would be nice to use the neighbour cache.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add protocol to neigh_tbl so that dst->ops->protocol is not needed
- Acquire the device from neigh->dev
This results in a neigh_hh_init that will cache the samve values
regardless of the packets flowing through it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no more callers so kill this function.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have ax25_neigh_output perform ordinary arp resolution before calling
ax25_neigh_xmit.
Call dev_hard_header in ax25_neigh_output with a destination address so
it will not fail, and the destination mac address will not need to be
set in ax25_neigh_xmit.
Remove arp_find from ax25_neigh_xmit (the ordinary arp resolution added
to ax25_neigh_output removes the need for calling arp_find).
Document how close ax25_neigh_output is to neigh_resolve_output.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rename ax25_rebuild_header to ax25_neigh_xmit and call it from
ax25_neigh_output directly. The rename is to make it clear
that this is not a rebuild_header operation.
- Remove ax25_rebuild_header from ax25_header_ops.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller is now is ax25_neigh_construct so move
neigh_compat_output into ax25_ip.c make it static and rename it
ax25_neigh_output.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The special case has been pushed out into ax25_neigh_construct so there
is no need to keep this code in arp.c
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AX25 already has it's own private arp cache operations to isolate
it's abuse of dev_rebuild_header to transmit packets. Add a function
ax25_neigh_construct that will allow all of the ax25 devices to
force using these operations, so that the generic arp code does
not need to.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user is in ax25_ip.c so stop exporting these functions.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two sets of header operations are functionally identical remove
the duplicate definition.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two sets of header operations are functionally identical remove the
duplicate definition.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patterned after the similar code in net/rom this turns out
to be a trivial obviously correct transmformation.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not setting the destination address is a bug that I suspect causes no
problems today, as only the arp code seems to call dev_hard_header and
the description I have of rose is that it is expected to be used with a
static neigbour table.
I have derived the offset and the length of the rose destination address
from rose_rebuild_header where arp_find calls neigh_ha_snapshot to set
the destination address.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely (impossible?) event that we attempt to transmit
an ax25 packet over a non-ax25 device free the skb so we don't
leak it.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Mellanox driver fixes
Two small fixes, please apply to net.
Both patches should go to 3.19.y too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d67 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masami noted that it would be better to hide the remaining CONFIG_BPF_SYSCALL-only
function declarations within the BPF header ifdef, w/o else path dummy alternatives
since these functions are not supposed to have a user outside of CONFIG_BPF_SYSCALL.
Suggested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reference: http://article.gmane.org/gmane.linux.kernel.api/8658
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A small batch with accumulated updates in nf-next, mostly IPVS updates,
they are:
1) Add 64-bits stats counters to IPVS, from Julian Anastasov.
2) Move NETFILTER_XT_MATCH_ADDRTYPE out of NETFILTER_ADVANCED as docker
seem to require this, from Anton Blanchard.
3) Use boolean instead of numeric value in set_match_v*(), from
coccinelle via Fengguang Wu.
4) Allows rescheduling of new connections in IPVS when port reuse is
detected, from Marcelo Ricardo Leitner.
5) Add missing bits to support arptables extensions from nft_compat,
from Arturo Borrero.
Patrick is preparing a large batch to enhance the set infrastructure,
named expressions among other things, that should follow up soon after
this batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both sk_attach_filter() and sk_attach_bpf() are setting up sk_filter,
charging skmem and attaching it to the socket after we got the eBPF
prog up and ready. Lets refactor that into a common helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue says:
====================
net: Remove iocb argument from sendmsg and recvmsg
Currently there is only one user - TIPC whose sendmsg() instances
using iocb argument. Meanwhile, there is no user using iocb argument
in its recvmsg() instance. Therefore, if we eliminate the werid usage
of iobc argument from TIPC, the iocb argument can be removed from
all sendmsg() and recvmsg() instances of the whole networking stack.
Reference:
https://patchwork.ozlabs.org/patch/433960/
Changes:
v2:
* Fix compile errors of DCCP module pointed by David
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the iocb argument is used to idenfiy whether or not socket
lock is hold before tipc_sendmsg()/tipc_send_stream() is called. But
this usage prevents iocb argument from being dropped through sendmsg()
at socket common layer. Therefore, in the commit we introduce two new
functions called __tipc_sendmsg() and __tipc_send_stream(). When they
are invoked, it assumes that their callers have taken socket lock,
thereby avoiding the weird usage of iocb argument.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to arptables extensions from nft_compat.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eyal Birger says:
====================
net: move skb->dropcount to skb->cb[]
Commit 977750076d ("af_packet: add interframe drop cmsg (v6)")
unionized skb->mark and skb->dropcount in order to allow recording
of the socket drop count while maintaining struct sk_buff size.
skb->dropcount was introduced since there was no available room
in skb->cb[] in packet sockets. However, its introduction led to
the inability to export skb->mark to userspace.
It was considered to alias skb->priority instead of skb->mark.
However, that would lead to the inabilty to export skb->priority
to userspace if desired. Such change may also lead to hard-to-find
issues as skb->priority is assumed to be alias free, and, as noted
by Shmulik Ladkani, is not 'naturally orthogonal' with other skb
fields.
This patch series follows the suggestions made by Eric Dumazet moving
the dropcount metric to skb->cb[], eliminating this problem
at the expense of 4 bytes less in skb->cb[] for protocol families
using it.
The patch series include compactization of bluetooth and packet
use of skb->cb[] as well as the infrastructure for placing dropcount
in skb->cb[].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 977750076d ("af_packet: add interframe drop cmsg (v6)")
unionized skb->mark and skb->dropcount in order to allow recording
of the socket drop count while maintaining struct sk_buff size.
skb->dropcount was introduced since there was no available room
in skb->cb[] in packet sockets. However, its introduction led to
the inability to export skb->mark, or any other aliased field to
userspace if so desired.
Moving the dropcount metric to skb->cb[] eliminates this problem
at the expense of 4 bytes less in skb->cb[] for protocol families
using it.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[], use
a common function in order to set dropcount in struct sk_buff.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[] use a common
macro in protocol families using skb->cb[] for ancillary data to
validate available room in skb->cb[].
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[], 4 bytes
of additional room are needed in skb->cb[] in packet sockets.
Store the skb original length in the first two fields of sockaddr_ll
(sll_family and sll_protocol) as they can be derived from the skb when
needed.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b885787ea ("net: Generalize socket rx gap / receive queue overflow cmsg")
allowed receiving packet dropcount information as a socket level option.
RXRPC sockets recvmsg function was changed to support this by calling
sock_recv_ts_and_drops() instead of sock_recv_timestamp().
However, protocol families wishing to receive dropcount should call
sock_queue_rcv_skb() or set the dropcount specifically (as done
in packet_rcv()). This was not done for rxrpc and thus this feature
never worked on these sockets.
Formalizing this by not calling sock_recv_ts_and_drops() in rxrpc as
part of an effort to move skb->dropcount into skb->cb[]
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert boolean fields incoming and req_start to bit fields and move
force_active in order save space in bt_skb_cb in an effort to use
a portion of skb->cb[] for storing skb->dropcount.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hci_req_ctrl is never used outside of struct bt_skb_cb;
Inlining it frees 8 bytes on a 64 bit system in skb->cb[] allowing
the addition of more ancillary data.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PADT frame is received, the socket may not be in a good state to
close down the PPP interface. The current implementation handles this by
simply blocking all further PPP traffic, and hoping that the lack of traffic
will trigger the user to investigate.
Use schedule_work to get to a process context from which we clear down the
PPP interface, in a fashion analogous to hangup on a TTY-based PPP
interface. This causes pppd to disconnect immediately, and allows tools to
take immediate corrective action.
Note that pppd's rp_pppoe.so plugin has code in it to disable the session
when it disconnects; however, as a consequence of this patch, the session is
already disabled before rp_pppoe.so is asked to disable the session. The
result is a harmless error message:
Failed to disconnect PPPoE socket: 114 Operation already in progress
This message is safe to ignore, as long as the error is 114 Operation
already in progress; in that specific case, it means that the PPPoE session
has already been disabled before pppd tried to disable it.
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag
stripping when the card cannot disable it. The driver should remove
NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed
for the ethtool.
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add *_SIZE macros for the bits ENDIA_DESC and
ENDIA_PKT
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program management descriptor's access mode according to the
dynamically detected CPU endianness.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
