On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.
With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With RC6 enabled, BYT has an HW issue in determining the right
Gfx busyness.
WA for Turbo + RC6: Use SW based Gfx busy-ness detection to decide
on increasing/decreasing the freq. This logic will monitor C0
counters of render/media power-wells over EI period and takes
necessary action based on these values
v2: Refactor duplicate code. (Ville)
v3: Reformat the comments. (Ville)
v4: Enable required counters and remove unwanted code (Ville)
v5: Added frequency change acceleration support and remove kernel-doc
style comments. (Ville)
v6: Updated comment section and Fix w/a comment. (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore waits use a new instruction, MI_SEMAPHORE_WAIT. The seqno to
wait on is all well defined by the table in the previous patch. There is
nothing else different from previous GEN's semaphore synchronization
code.
v2: Update macros to not require the other ring's ring->id (Chris)
v3: Add missing VCS2 gen8_ring_wait init besides
s/ring_buffer/engine_cs (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore signalling works similarly to previous GENs with the exception
that the per ring mailboxes no longer exist. Instead you must define
your own space, somewhere in the GTT.
The comments in the code define the layout I've opted for, which should
be fairly future proof. Ie. I tried to define offsets in abstract terms
(NUM_RINGS, seqno size, etc).
NOTE: If one wanted to move this to the HWSP they could. I've decided
one 4k object would be easier to deal with, and provide potential wins
with cache locality, but that's all speculative.
v2: Update the macro to not need the other ring's ring->id (Chris)
Update the comment to use the correct formula (Chris)
v3: Move the macros the ringbuffer.h to prevent churn in next patch
(Ville)
v4: Fixed compilation rebase conflict
commit 1ec9e26dda
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Feb 14 14:01:11 2014 +0100
drm/i915: Consolidate binding parameters into flags
v5: VCS2 rebase
Replace hweight_long with hweight32
v6 (Rodrigo): * Add missed VC2 gen8 ring signal init
* fixing conflicst on rebase
* minor fixes on address table
* remove WARN_ON
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid using magic values for CCK frequency bits. Also the mask we were
using for the requested frequency was one bit too short. Fix it up.
Note: This also fixes the #define for a mask (spotted by Jesse in his
review).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add note about mask change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Beignet needs these in order to program the L3 cache config for
OpenCL workloads, particularly when using SLM.
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two BSpec updates changed the recommended values for BDW eDP and DP
DDI buffer translations. Now the signal levels also match the HSW signal
levels, which simplify things a little bit.
It seems some DP sinks don't work properly without voltage level 0 and
pre-emphasis level 3, so this patch may fix some bugs on
panels/monitors that happen on BDW but not on HSW.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When link is in stand by and PSR exit is triggered by a primary or sprite
plane flip this mode allows only one single updated frame to be send to
display than get back to PSR immediately.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For no reason at all the public docs lack them, and Dave needs them
for his hpd interrupt rework.
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conceptually, the MIPI registers are addressed by the MIPI transcoder
index, not the pipe. It doesn't matter right now, because there's a
1:1 relationship between pipes and MIPI transcoders, but that change
allows us to break that link in the future
V1: Created new patch to address Damien's review comment.
Replacing _PIPE calls to _TRANSCODER calls
V2: Re-basing on patch 2
V3: Re-basing on patch 2
V4: Re-basing on patch 2
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Re-define MIPI register definitions in such a way that most of
the existing DSI code can be re-used for future platforms. Register
definitions are re-written using MMIO offset variable, so that without
changing the existing sequence, same code can be generically applied.
V4: Addressing review comments by Damien and Ville, splitting into two patches
This patch removes all the un-necessary formatting changes from previous patch.
V5: Removed 80 char limit formatting for existing MIPI regs
V6: Removed extra space, change one definition
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DIP registers are a mess on VLV and CHV. The register block on pipe
A is different than the register block on pipes B and C. In order to
handle that using the pipe offsets, we'd need a new pipe offset per
register, which seems wasteful. So instead just use the _PIPE3() macro
to handle these registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are just single registers so wasting space for the pipe offsets
seems a bit pointless. So just use the _PIPE3() macro instead.
Also rewrite the _PIPE3() macro to be more obvious, and protect the
arguments properly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to force the PHY clock buffer enables to make the clock routing
work.
v2: Fix the pipe B case to actually enable CH0 clock buffers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These should make it possible to feed port C from pipe A or port B from
pipe B. Didn't quite seem to work though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Disable media turbo and Add DOWN_IDLE_AVG support (Ville)
v3: Mass rename of the dev_priv->rps variables in upstream.
v4: Rebase against latest code. (Deepak)
v5: Rebase against latest nightly code. (Deepak)
v6: Rename the variables to match the spec (Mika)
v7: change min/max freq variable naming to match spec (Mika)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Configure PCBR if BIOS fails allocate pcbr (deepak)
v3: Fix PCBR condition check during CHV RC6 Enable flag set
v4: Fixup PCBR comment msg. (Chris)
Rebase against latest code (Deak)
Fixup Spurious hunk (Ben)
v5: Fix PCBR and commentis msg (mika)
v6: Rebase patch on latest nightly (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
85x also has a similar AGPBUSY# bit as gen3. Enable it to make
sure vblank interrupts don't get dealyed during C3 state.
There's also another bit which controls whether AGPBUSY# is asserted
based on pending cacheable cycles and interrupts, or just based on
pending commands in the ring and interrupts. Select the cacheable
cycles mode since that seems to be the new way of doing things in
85x, and it does give slightly better C3 residency numbers with
glxgears running.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My Gen3 Bspec lists the AGPBUSY# bit in INSTPM as an enable bit rather
than a disable bit. Our code has the opposite idea. Make the code match
the spec.
Might fix some gen3 C3 related interrupt delivery problems. Untested
due to lack of hardware.
v2: call it AGPBUSY_INT_EN to make it clearer it has to do with interrupts
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we need to disable VCP unit clock gating around media reset
on g4x.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Document the internal structure of the VLV display PHY a bit to help
people understand how the different register blocks relate to each
other.
v2: Add a bit more text
Make it a DOC: comment, but leave the ascii art out since
it would get mangled
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comments in i915_reg.h aren't proper kernel-doc comments, so replace
the magic /** with just /*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following workarounds should be needed for pre-production hardware
only:
* WaDisablePwrmtrEvent:chv
* WaSetMaskForGfxBusyness:chv
* WaDisableGunitClockGating:chv
* WaDisableFfDopClockGating:chv
* WaDisableDopClockGating:chv
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're using the reset domains bits for g4x on ilk. But on ilk those bits
actually shifted by one bit. Fix it up so that we use the correct bits.
We were actually always writing 0x2 to the reset domain bits, which
is a reserved value. In practice it looks like the hardware ignores that
value since nothing happens if I write that value when there's a 3D
workload running. Writing the _correct_ render domain value actually
makes the GPU stop.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.
v2: Add (1<<31) mask (Ville)
v3: Add Gen check for the mask (ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2ed
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill in the sprite bits for DDL1/DDL2 registers, and add DDL3.
Still need to write the code to use these...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed by the VLV S0ix context save/restore helpers.
v2:
- unchanged
v3:
- use proper GEN register prefixes (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to Pipe C DPINVGTT has more bits on CHV.
v2: Fix comment to say VLV/CHV (Rafael)
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase on top of Ben's GT interrupt shuffling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has pipe C and PSR which cause changes to DPFLIPSTAT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: We probably want to sprinkle _CHV suffixes over these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
