This patch moves the tpm_tis_reenable_interrupts function out of the
CONFIG_PNP-surrounded #define block. This solves a compilation error in
case CONFIG_PNP is not defined.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Morris <jmorris@namei.org>
The is_itpm() function is only accessed from a block surrounded by
#ifdef CONFIG_PNP. Therefore, also surround it with #ifdef CONFIG_PNP
and remove the #else branch causing the warning.
http://lxr.linux.no/#linux+v2.6.39/drivers/char/tpm/tpm_tis.c#L622
v2:
- fixes a previous typo
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Morris <jmorris@namei.org>
This patch introduces a function for automatic probing for the Intel iTPM
STS_DATA_EXPECT flaw.
The patch splits the current tpm_tis_send function into 2 parts where the 1st
part is now called tpm_tis_send_data() and merely sends the data to the TPM.
This function is then used for probing. The new tpm_tis_send function now
first calls tpm_tis_send_data and if that succeeds has the TPM process the
command and waits until the response is there.
The probing for the Intel iTPM is only invoked if the user has not passed
itpm=1 as parameter for the module *or* if such a TPM was detected via ACPI.
Previously it was necessary to pass itpm=1 when also passing force=1 to the
module when doing a 'modprobe'. This function is more general than the ACPI
test function and the function relying on ACPI could probably be removed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes several aspects of the probing for interrupts.
This patch reads the TPM's timeouts before probing for the interrupts. The
tpm_get_timeouts() function is invoked in polling mode and gets the proper
timeouts from the TPM so that we don't need to fall back to 2 minutes timeouts
for short duration commands while the interrupt probing is happening.
This patch introduces a variable probed_irq into the vendor structure that gets
the irq number if an interrupt is received while the the tpm_gen_interrupt()
function is run in polling mode during interrupt probing. Previously some
parts of tpm_gen_interrupt() were run in polling mode, then the irq variable
was set in the interrupt handler when an interrupt was received and execution
of tpm_gen_interrupt() ended up switching over to interrupt mode.
tpm_gen_interrupt() execution ended up on an event queue where it eventually
timed out since the probing handler doesn't wake any queues.
Before calling into free_irq() clear all interrupt flags that may have
been set by the TPM. The reason is that free_irq() will call into the probing
interrupt handler and may otherwise fool us into thinking that a real interrupt
happened (because we see the flags as being set) while the TPM's interrupt line
is not even connected to anything on the motherboard. This solves a problem
on one machine I did testing on (Thinkpad T60).
If a TPM claims to use a specifc interrupt, the probing is done as well
to verify that the interrupt is actually working. If a TPM indicates
that it does not use a specific interrupt (returns '0'), probe all interrupts
from 3 to 15.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch delays the (ACPI S3) suspend while the TPM is busy processing a
command and the TPM TIS driver is run in interrupt mode. This is the same
behavior as we already have it for the TPM TIS driver in polling mode.
Reasoning: Some of the TPM's commands advance the internal state of the TPM.
An example would be the extending of one of its PCR registers. Upper layers,
such as IMA or TSS (TrouSerS), would certainly want to be sure that the
command succeeded rather than getting an error code (-62 = -ETIME) that may
not give a conclusive answer as for what reason the command failed. Reissuing
such a command would put the TPM into the wrong state, so waiting for it to
finish is really the only option.
The downside is that some commands (key creation) can take a long time and
actually prevent the machine from entering S3 at all before the 20 second
timeout of the power management subsystem arrives.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch makes sure that if the TPM TIS interface is run in interrupt mode
(rather than polling mode) that all interrupts are enabled in the TPM's
interrupt enable register after a resume from ACPI S3 suspend. The registers
may either have been cleared by the TPM loosing its state during device sleep
or by the BIOS leaving the TPM in polling mode (after sending a command to
the TPM for starting it up again)
You may want to check if your TPM runs with interrupts by doing
cat /proc/interrupts | grep -i tpm
and see whether there is an entry or otherwise for it to use interrupts:
modprobe tpm_tis interrupts=1 [add 'itpm=1' for Intel TPM ]
v2:
- the patch was adapted to work with the pnp and platform driver
implementations in tpm_tis.c
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes the TPM's pubek sysfs entry that is accessible as long
as the TPM doesn't have an owner. It was necessary to shift the access to the
data by -10 -- the first byte immediately follows the 10 byte header. The
line
data = tpm_cmd.params.readpubek_out_buffer;
sets it at the offset '10' in the packet, so we can read the data array
starting at offset '0'.
Before:
Algorithm: 00 0C 00 00
Encscheme: 08 00
Sigscheme: 00 00
Parameters: 00 00 00 00 01 00 AC E2 5E 3C A0 78
Modulus length: -563306801
Modulus:
28 21 08 0F 82 CD F2 B1 E7 49 F7 74 70 BE 59 8C
43 78 B1 24 EA 52 E2 FE 52 5C 3A 12 3B DC 61 71
[...]
After:
Algorithm: 00 00 00 01
Encscheme: 00 03
Sigscheme: 00 01
Parameters: 00 00 08 00 00 00 00 02 00 00 00 00
Modulus length: 256
Modulus:
AC E2 5E 3C A0 78 DE 6C 9E CF 28 21 08 0F 82 CD
F2 B1 E7 49 F7 74 70 BE 59 8C 43 78 B1 24 EA 52
[...]
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's interface timeouts in a 'timeouts' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Adjust the interface timeouts if they are found to be too small, i.e., if
they are returned in milliseconds rather than microseconds as we heared
from Infineon that some (old) Infineon TPMs do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
The TPM driver currently discards the interface timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 4 interface timeout indicators of type u32.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's command timeouts in a 'durations' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Adjust the durations if they are found to be too small, i.e., if they are
returned in milliseconds rather than microseconds as some Infineon TPMs are
reported to do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
The TPM driver currently discards the durations values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
v4:
- sysfs entry 'durations' is now a patch of its own
- the work-around for TPMs reporting durations in milliseconds is now in a
patch of its own
v3:
- sysfs entry now called 'durations' to resemble TPM-speak (previously
was called 'timeouts')
v2:
- adjusting all timeouts for TPM devices reporting timeouts in msec rather
than usec
- also displaying in sysfs whether the timeouts are 'original' or 'adjusted'
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
When interrupts are delayed due to interrupt masking or due to other
interrupts being serviced the HPET periodic-emuation would fail. This
happened because given an interval t and a time for the current interrupt
m we would compute the next time as t + m. This works until we are
delayed for > t, in which case we would be writing a new value which is in
fact in the past.
This can be solved by computing the next time instead as (k * t) + m where
k is large enough to be in the future. The exact computation of k is
described in a comment to the code.
More detail:
Assuming an interval of 5 between each expected interrupt we have a normal
case of
t0: interrupt, read t0 from comparator, set next interrupt t0 + 5
t5: interrupt, read t5 from comparator, set next interrupt t5 + 5
t10: interrupt, read t10 from comparator, set next interrupt t10 + 5
...
So, what happens when the interrupt is serviced too late?
t0: interrupt, read t0 from comparator, set next interrupt t0 + 5
t11: delayed interrupt serviced, read t5 from comparator, set next
interrupt t5 + 5, which is in the past!
... counter loops ...
t10: Much much later, get the next interrupt.
This can happen either because we have interrupts masked for too long
(some stupid driver goes on a printk rampage) or just because we are
pushing the limits of the interval (too small a period), or both most
probably.
My solution is to read the main counter as well and set the next interrupt
to occur at the right interval, for example:
t0: interrupt, read t0 from comparator, set next interrupt t0 + 5
t11: delayed interrupt serviced, read t5 from comparator, set next
interrupt t15 as t10 has been missed.
t15: back on track.
Signed-off-by: Nils Carlson <nils.carlson@ericsson.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That's already been done by the virtio infrastructure before the probe
function is called.
Reported-by: alexey.kardashevskiy@au1.ibm.com
Acked-by: Amit Shah <amit.shah@redhat.com>
Tested-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
parport_find_number() calls parport_get_port() on its result, so there
should be a corresponding call to parport_put_port() before dropping the
reference. Similar code is found in the function register_device() in the
same file.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression struct parport * x;
expression ra,rr;
statement S1,S2;
@@
x = parport_find_number(...)
... when != x = rr
when any
when != parport_put_port(x,...)
when != if (...) { ... parport_put_port(x,...) ...}
(
if(<+...x...+>) S1 else S2
|
if(...) { ... when != x = ra
when forall
when != parport_put_port(x,...)
*return...;
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let memory allocator initialize the allocated memory as null, thus remove
the use of memset.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let i8k create an hwmon class device so that libsensors will expose
the CPU temperature and fan speeds to monitoring applications.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Massimo Dal Zotto <dz@debian.org>
i8k uses lahf to read the flag register in 64-bit code; early x86-64
CPUs, however, lack this instruction and we get an invalid opcode
exception at runtime.
Use pushf to load the flag register into the stack instead.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Reported-by: Jeff Rickman <jrickman@myamigos.us>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Cc: stable@kernel.org
Cc: Massimo Dal Zotto <dz@debian.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
apm_mutex is locked by a process (e.g. apm -s) at the start of apm_ioctl() and
remains locked while pm_suspend() is called. Any subsequent process trying to
ACK the suspend (e.g. apmd) is then blocked at the start of apm_ioctl(),
causing the suspend to be delayed for 5 seconds in apm_suspend_notifier()
while the ACK times out. In short, ACKs don't work.
The driver's data structures are sufficiently protected by assorted locks. And
pm_suspend() has its own mutex to prevent reentrancy. Consequently there is no
obvious requirement for apm_mutex, which evolved from earlier BKL calls. So
let's remove it.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This was based on a description by Ben Herrenschmidt:
> I've removed that SBA reset from the normal TLB invalidation path and
> left it only once after turning AGP on.
About six months ago, he said:
> I did it a bit differently, but yeah, you get the idea. I'm doing a
> patch series so don't bother pushing things too hard yet.
But I haven't seen anything from him about this since then, and people are
regularly hitting these lockups, so here we are...
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (45 commits)
crypto: caam - add support for sha512 variants of existing AEAD algorithms
crypto: caam - remove unused authkeylen from caam_ctx
crypto: caam - fix decryption shared vs. non-shared key setting
crypto: caam - platform_bus_type migration
crypto: aesni-intel - fix aesni build on i386
crypto: aesni-intel - Merge with fpu.ko
crypto: mv_cesa - make count_sgs() null-pointer proof
crypto: mv_cesa - copy remaining bytes to SRAM only when needed
crypto: mv_cesa - move digest state initialisation to a better place
crypto: mv_cesa - fill inner/outer IV fields only in HMAC case
crypto: mv_cesa - refactor copy_src_to_buf()
crypto: mv_cesa - no need to save digest state after the last chunk
crypto: mv_cesa - print a warning when registration of AES algos fail
crypto: mv_cesa - drop this call to mv_hash_final from mv_hash_finup
crypto: mv_cesa - the descriptor pointer register needs to be set just once
crypto: mv_cesa - use ablkcipher_request_cast instead of the manual container_of
crypto: caam - fix printk recursion for long error texts
crypto: caam - remove unused keylen from session context
hwrng: amd - enable AMD hw rnd driver for Maple PPC boards
hwrng: amd - manage resource allocation
...
Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (44 commits)
debugfs: Silence DEBUG_STRICT_USER_COPY_CHECKS=y warning
sysfs: remove "last sysfs file:" line from the oops messages
drivers/base/memory.c: fix warning due to "memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION"
memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION
SYSFS: Fix erroneous comments for sysfs_update_group().
driver core: remove the driver-model structures from the documentation
driver core: Add the device driver-model structures to kerneldoc
Translated Documentation/email-clients.txt
RAW driver: Remove call to kobject_put().
reboot: disable usermodehelper to prevent fs access
efivars: prevent oops on unload when efi is not enabled
Allow setting of number of raw devices as a module parameter
Introduce CONFIG_GOOGLE_FIRMWARE
driver: Google Memory Console
driver: Google EFI SMI
x86: Better comments for get_bios_ebda()
x86: get_bios_ebda_length()
misc: fix ti-st build issues
params.c: Use new strtobool function to process boolean inputs
debugfs: move to new strtobool
...
Fix up trivial conflicts in fs/debugfs/file.c due to the same patch
being applied twice, and an unrelated cleanup nearby.
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Just use the Sandy Bridge routines.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
If cdev_add() fails, there is no justification for subsequently
calling kobject_put().
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow setting of maximal number of raw devices as a module parameter. This
requires changing of static array into a vmalloced one (the array is going to
be too large for kmalloc).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the unnecessary initialization of "dev_t bsr_dev" since it's
subsequently used in an "alloc_chrdev_region()" call which uses that
variable in an output-only fashion.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PPC 970FX Evaluation kit (Maple) boards bear AMD8111 southbridge.
Allow this driver to be compiled in if PPC_MAPLE is selected.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As amd driver doesn't bind to PCI device, we'd better manage reource
allocation on our own to disallow (possible) conflicts.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: console: Enable call to hvc_remove() on console port remove
virtio_pci: Prevent double-free of pci regions after device hot-unplug
virtio: Decrement avail idx on buffer detach
This call was disabled as hot-unplugging one virtconsole port led to
another virtconsole port freezing.
Upon testing it again, this now works, so enable it.
In addition, a bug was found in qemu wherein removing a port of one type
caused the guest output from another port to stop working. I doubt it
was just this bug that caused it (since disabling the hvc_remove() call
did allow other ports to continue working), but since it's all solved
now, we're fine with hot-unplugging of virtconsole ports.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
pg_start is copied from userspace on AGPIOC_BIND and AGPIOC_UNBIND ioctl
cmds of agp_ioctl() and passed to agpioc_bind_wrap(). As said in the
comment, (pg_start + mem->page_count) may wrap in case of AGPIOC_BIND,
and it is not checked at all in case of AGPIOC_UNBIND. As a result, user
with sufficient privileges (usually "video" group) may generate either
local DoS or privilege escalation.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
page_count is copied from userspace. agp_allocate_memory() tries to
check whether this number is too big, but doesn't take into account the
wrap case. Also agp_create_user_memory() doesn't check whether
alloc_size is calculated from num_agp_pages variable without overflow.
This may lead to allocation of too small buffer with following buffer
overflow.
Another problem in agp code is not addressed in the patch - kernel memory
exhaustion (AGPIOC_RESERVE and AGPIOC_ALLOCATE ioctls). It is not checked
whether requested pid is a pid of the caller (no check in agpioc_reserve_wrap()).
Each allocation is limited to 16KB, though, there is no per-process limit.
This might lead to OOM situation, which is not even solved in case of the
caller death by OOM killer - the memory is allocated for another (faked) process.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
printk: /dev/kmsg - properly support writev() to avoid interleaved printk lines
We should avoid calling printk() in a loop, when we pass a single
string to /dev/kmsg with writev().
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce the lines of code and simplify the logic.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
