IQD devices offer limited support for bulking: all frames in a TX buffer
need to have the same target. qeth_iqd_may_bulk() implements this
constraint, and allows us to defer the TX doorbell until
(a) the buffer is full (since each buffer needs its own doorbell), or
(b) the entire TX queue is full, or
(b) we reached the BQL limit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each TX buffer may contain multiple skbs. So just accumulate the sent
byte count in the buffer struct, and later use the same count when
completing the buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the stack to bulk-free our TX-completed skbs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to their large MTU and potentially low utilization of TX buffers,
IQD devices in particular require fast TX recycling. This makes them
a prime candidate for a TX NAPI path in qeth.
qeth_tx_poll() uses the recently introduced qdio_inspect_queue() helper
to poll the TX queue for completed buffers. To avoid hogging the CPU for
too long, we yield to the stack after completing an entire queue's worth
of buffers.
While IQD is expected to transfer its buffers synchronously (and thus
doesn't support TX interrupts), a timer covers for the odd case where a
TX buffer doesn't complete synchronously. Currently this timer should
only ever fire for
(1) the mcast queue,
(2) the occasional race, where the NAPI poll code observes an update to
queue->used_buffers while the TX doorbell hasn't been issued yet.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This consolidates the SW statistics code, and improves it to
(1) account for the header overhead of each segment on a TSO skb,
(2) count dangling packets as in-error (during eg. shutdown), and
(3) only count offloads when the skb was successfully transmitted.
We also count each segment of an TSO skb as one packet - except for
tx_dropped, to be consistent with dev->tx_dropped.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a driver wants to use the new Output Queue poll code, then the qdio
layer must disable its internal Queue scanning. Let the driver select
this mode by passing a special scan_threshold of 0.
As the scan_threshold is the same for all Output Queues, also move it
into the main qdio_irq struct. This allows for fast opt-out checking, a
driver is expected to operate either _all_ or none of its Output Queues
in polling mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit d36deae750 ("qdio: extend API to allow polling") enhanced
the qdio layer so that drivers can poll their Input Queues, we don't
have the corresponding infrastructure for Output Queues yet.
Factor out a helper that scans a single QDIO Queue, so that qeth can
implement TX NAPI on top of it.
While doing so, remove the duplicated tracking of the next-to-scan index
(q->first_to_check vs q->first_to_kick) in this code path.
qdio_handle_aobs() needs to move slightly upwards in the code hierarchy,
so that it's still called from the polling path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit added logic to determine the appropriate statistics block
size to allocate and the size is stored in bp->hw_ring_stats_size. But
if the firmware spec is older than 1.6.0, it is 0 and not initialized.
This causes the allocation to fail with size 0 and bnxt_open() to
abort. Fix it by always initializing bp->hw_ring_stats_size to the
legacy default size value.
Fixes: 4e74850663 ("bnxt_en: Allocate the larger per-ring statistics block for 57500 chips.")
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The consume_skb() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
warning: tuple_key_info defined but not used [-Wunused-const-variable=]
The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an unlikely case, use unlikely() on it seems logical.
Signed-off-by: xiaolinkui <xiaolinkui@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Aaro this patch causes network problems on
MIPS Loongson platform. Therefore revert it.
Fixes: f072218cca ("r8169: remove not needed call to dma_sync_single_for_device")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timestamps are currently communicated to user space as 'struct
timespec', which is not considered y2038 safe since it uses a 32-bit
signed value for seconds.
Fix this while the API is still not part of any official kernel release
by using 64-bit nanoseconds timestamps instead.
Fixes: ca30707dee ("drop_monitor: Add packet alert mode")
Fixes: 5e58109b1e ("drop_monitor: Add support for packet alert mode for hardware drops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RDMA cookie and RX timestamp to the usercopy whitelist.
After the introduction of hardened usercopy whitelisting
(https://lwn.net/Articles/727322/), a warning is displayed when the
RDMA cookie or RX timestamp is copied to userspace:
kernel: WARNING: CPU: 3 PID: 5750 at
mm/usercopy.c:81 usercopy_warn+0x8e/0xa6
[...]
kernel: Call Trace:
kernel: __check_heap_object+0xb8/0x11b
kernel: __check_object_size+0xe3/0x1bc
kernel: put_cmsg+0x95/0x115
kernel: rds_recvmsg+0x43d/0x620 [rds]
kernel: sock_recvmsg+0x43/0x4a
kernel: ___sys_recvmsg+0xda/0x1e6
kernel: ? __handle_mm_fault+0xcae/0xf79
kernel: __sys_recvmsg+0x51/0x8a
kernel: SyS_recvmsg+0x12/0x1c
kernel: do_syscall_64+0x79/0x1ae
When the whitelisting feature was introduced, the memory for the RDMA
cookie and RX timestamp in RDS was not added to the whitelist, causing
the warning above.
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Tested-by: Jenny <jenny.x.xu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return code value could be non deterministic in case of wrong size read.
With this patch, if such error occurs, set rc to be -EIO.
In addition, mlx5_hv_config_common() supports reading of
HV_CONFIG_BLOCK_SIZE_MAX bytes only, fix to early return error with
bad input.
Fixes: 913d14e866 ("net/mlx5: Add wrappers for HyperV PCIe operations")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: save EEE
v4:
For patch #2, remove redundant calling of "ocp_reg_write(tp, OCP_EEE_ADV, 0)".
v3:
For patch #2, fix the mistake caused by copying and pasting.
v2:
Adjust patch #1. The EEE has been disabled in the beginning of
r8153_hw_phy_cfg() and r8153b_hw_phy_cfg(), so only check if
it is necessary to enable EEE.
Add the patch #2 for the helper function.
v1:
Saving the settings of EEE to avoid they become the default settings
after reset_resume().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function "rtl_eee_enable" for setting EEE. Besides, I
move r8153_eee_en() and r8153b_eee_en(). And, I remove r8152b_enable_eee(),
r8153_set_eee(), and r8153b_set_eee().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saving the settings of EEE to avoid they become the default settings
after reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update response packet length for the following commands per NC-SI spec
- Get Controller Packet Statistics
- Get NC-SI Statistics
- Get NC-SI Pass-through Statistics command
Signed-off-by: Ben Wei <benwei@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong says:
====================
dt-bindings: net: meson-dwmac: convert to yaml
This patchsets converts the Amlogic Meson DWMAC glue bindings over to
YAML schemas using the already converted dwmac bindings.
The first patch is needed because the Amlogic glue needs a supplementary
reg cell to access the DWMAC glue registers.
Changes since v3:
- Specified net-next target tree
Changes since v2:
- Added review tags
- Updated allwinner,sun7i-a20-gmac.yaml reg maxItems
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the DT validation in place, let's convert the device tree
bindings for the Synopsys DWMAC Glue for Amlogic SoCs over to a YAML schemas.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Amlogic Meson DWMAC glue bindings needs a second reg cells for the
glue registers, thus update the reg minItems/maxItems to allow more
than a single reg cell.
Also update the allwinner,sun7i-a20-gmac.yaml derivative schema to specify
maxItems to 1.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-08-22
This series contains updates to i40e driver only.
Arnd Bergmann reduces the stack usage which was causing warnings on
32-bit architectures due to large structure sizes for 2 functions
getting inlined, so use noinline_for_stack to prevent the compilers from
combining the 2 functions.
Mauro S. M. Rodrigues fixes an issue when reading an EEPROM from SFP
modules that comply with SFF-8472 but do not implement the Digital
Diagnostic Monitoring (DDM) interface for i40e.
Huhai found we were not checking the return value for configuring the
transmit ring and continuing with XDP configuration of the transmit
ring.
Beilei fixes an issue of shifting signed 32-bit integers.
Sylwia adds support for "packet drop mode" to the MAC configuration for
admin queue command. This bit controls the behavior when a no-drop
packet is blocking a TC queue. Adds support for persistent LLDP by
checking the LLDP flag and reading the LLDP from the NVM when enabled.
Adrian fixes the "recovery mode" check to take into account which device
we are on, since x710 devices have 4 register values to check for status
and x722 devices only have 2 register values to check.
Piotr Azarewicz bumps the supported firmware API version to 1.9 which
extends the PHY access admin queue command support.
Jake makes sure the traffic class stats for a VEB are reset when the VEB
stats are reset.
Slawomir fixes a NULL pointer dereference where the VSI pointer was not
updated before passing it to the i40e_set_vf_mac() when the VF is in a
reset state, so wait for the reset to complete.
Grzegorz removes the i40e_update_dcb_config() which was not using the
correct NVM reads, so call i40e_init_dcb() in its place to correctly
update the DCB configuration.
Piotr Kwapulinski expands the scope of i40e_set_mac_type() since this is
needed during probe to determine if we are in recovery mode. Fixed the
driver reset path when in recovery mode.
Marcin fixed an issue where we were breaking out of a loop too early
when trying to get the PHY capabilities.
v2: Combined patch 7 & 9 in the original series, since both patches
bumped firmware API version. Also combined patches 12 & 13 in the
original series, since one increased the scope of checking for MAC
and the follow-on patch made use of function within the new scope.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug where driver was breaking out of the loop and
reporting an error without retrying first.
Signed-off-by: Marcin Formela <marcin.formela@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver waits after issuing a reset. When a reset takes too long a driver
gives up. Implemented by invoking PF reset in a loop. After defined
number of unsuccessful PF reset trials it returns error.
Without this patch PF reset fails when NIC is in recovery mode.
So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type()
to be public. It is required for recovery mode handling. Without this patch
recovery mode could not be detected in i40e_probe().
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes function i40e_update_dcb_config(). Instead of
i40e_update_dcb_config() we use i40e_init_dcb(), which implements the
correct NVM read.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add update to the VSI pointer passed to the i40e_set_vf_mac function.
If VF is in reset state the driver waits in i40e_set_vf_mac function
for the reset to be complete, yet after reset the vsi pointer
that was passed into this function is no longer valid.
The patch updates local VSI pointer directly from pf->vsi array,
by using the id stored in VF pointer (lan_vsi_idx).
Without this commit the driver might occasionally invoke general
protection fault in kernel and disable the OS entirely.
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: Adrian Podlawski <adrian.podlawski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should
exit from i40e_vsi_configure_tx and return the error, instead of continuing
to check whether xdp is enable, and configure the xdp transmit ring.
Signed-off-by: huhai <huhai@kylinos.cn>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to the ixgbe issue fixed in:
655c914145 ("ixgbe: Check DDM existence in transceiver before access)
i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.
Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.
As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:
drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]
When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.
The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.
Fixes: 0a862b43ac ("i40e/i40evf: Add module_types and update_link_info")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused Value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang says:
====================
Add software backchannel and mlx5e HV VHCA stats
This patch set adds paravirtual backchannel in software in pci_hyperv,
which is required by the mlx5e driver HV VHCA stats agent.
The stats agent is responsible on running a periodic rx/tx packets/bytes
stats update.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HV VHCA stats agent is responsible on running a preiodic rx/tx
packets/bytes stats update. Currently the supported format is version
MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data
transfer from the VF to the PF.
The reporter fetch the statistics data from all opened channels, fill it
in a buffer and send it to mlx5_hv_vhca_write_agent.
As the stats layer should include some metadata per block (sequence and
offset), the HV VHCA layer shall modify the buffer before actually send it
over block 1.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control agent is responsible over of the control block (ID 0). It should
update the PF via this block about every capability change. In addition,
upon block 0 invalidate, it should activate all other supported agents
with data requests from the PF.
Upon agent create/destroy, the invalidate callback of the control agent
is being called in order to update the PF driver about this change.
The control agent is an integral part of HV VHCA and will be created
and destroy as part of the HV VHCA init/cleanup flow.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HV VHCA is a layer which provides PF to VF communication channel based on
HyperV PCI config channel. It implements Mellanox's Inter VHCA control
communication protocol. The protocol contains control block in order to
pass messages between the PF and VF drivers, and data blocks in order to
pass actual data.
The infrastructure is agent based. Each agent will be responsible of
contiguous buffer blocks in the VHCA config space. This infrastructure will
bind agents to their blocks, and those agents can only access read/write
the buffer blocks assigned to them. Each agent will provide three
callbacks (control, invalidate, cleanup). Control will be invoked when
block-0 is invalidated with a command that concerns this agent. Invalidate
callback will be invoked if one of the blocks assigned to this agent was
invalidated. Cleanup will be invoked before the agent is being freed in
order to clean all of its open resources or deferred works.
Block-0 serves as the control block. All execution commands from the PF
will be written by the PF over this block. VF will ack on those by
writing on block-0 as well. Its format is described by struct
mlx5_hv_vhca_control_block layout.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrapper functions for HyperV PCIe read / write /
block_invalidate_register operations. This will be used as an
infrastructure in the downstream patch for software communication.
This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface driver is a helper driver allows other drivers to
have a common interface with the Hyper-V PCI frontend driver.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
