Some supported devices support burst read function. This provides a method
for reading a batch of data (status, temperature, gyroscopes,
accelerometers, time stamp/data counter, and CRC code), which does not
require a stall time between each 16-bit segment and only requires one
command on the DIN line to initiate. Devices supporting this mode
are:
* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210422103735.136367-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No point in calling pm_runtime_put_noidle() that isn't balancing a get.
Note no actual impact because the runtime pm core protects against
a negative reference counter.
For the pm_runtime_resume_and_get() main interest is in clearing
out this old pattern to avoid it getting coppied into new submissions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210509113354.660190-10-jic23@kernel.org
Fix wrongly stated 13 Hz ODR for accelerometers, the correct ODR is 12.5 Hz
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can utilize separate drivers for accelerometer and magnetometer,
so here is the glue driver to enable LSM9DS0 IMU support.
The idea was suggested by Crestez Dan Leonard in [1]. The proposed change
was sent as RFC due to race condition concerns, which are indeed possible.
In order to amend the initial change, I went further by providing a specific
multi-instantiate probe driver that reuses existing accelerometer and
magnetometer.
[1]: https://lore.kernel.org/patchwork/patch/670353/
Suggested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: mr.lahorde@laposte.net
Cc: Matija Podravec <matija_podravec@fastmail.fm>
Cc: Sergey Borishchenko <borischenko.sergey@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210414195454.84183-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Continuing from Alexandru Ardelean's introduction of the split between
driver modifiable fields and those that should only be set by the core.
This could have been done in two steps to make the actual move after
introducing iio_device_id() but there seemed limited point to that
given how mechanical the majority of the patch is.
Includes fixup from Alex for missing mxs-lradc-adc conversion.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426174911.397061-2-jic23@kernel.org
With commit 3ba10e37371d ("iio: adis: add burst_max_speed_hz variable"), we
just need to define 'burst_max_speed_hz' and the adis core will take
care of setting up the spi transfers for burst mode. Hence, we fix
a potential race with the spi core where we could be left witn an
invalid 'max_speed_hz'.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Fixes: 5eda3550a3 ("staging:iio:adis16400: Preallocate transfer message")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-7-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With commit 3ba10e37371d ("iio: adis: add burst_max_speed_hz variable"), we
just need to define 'burst_max_speed_hz' and the adis core will take
care of setting up the spi transfers for burst mode. Hence, we fix
a potential race with the spi core where we could be left with an
invalid 'max_speed_hz'.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Fixes: fff7352bf7 ("iio: imu: Add support for adis16475")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-6-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Typically, in burst mode, the device cannot operate at it's full spi
speed. Hence, the spi transfers for burst mode have to take this into
account. With this change we avoid a potential race with the spi core as
drivers were 'hacking' the device 'max_speed_hz' directly in the
trigger handler.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There's no point in pushing data to IIO buffers in case 'spi_sync()'
fails.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-4-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It makes more sense to update the device page as soon as we we
successfully changed it. Moreover, a follow up patch will handle
'spi_sync' error path which would leave 'current_page' in a inconsistent
state.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210427085454.30616-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On an IRQ handler we should not return normal error codes as 'irqreturn_t'
is expected.
This is done by jumping to the 'check_burst32' label where we return
'IRQ_HANDLED'. Note that it is fine to do the burst32 check in this
error path. If we have proper settings to apply burst32, we might just
do the setup now so that the next sample already uses it.
Fixes: fff7352bf7 ("iio: imu: Add support for adis16475")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On the trigger handler, we might need to change the device page. Hence,
we should check the return value from 'spi_write()' and act accordingly.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210422101911.135630-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On an IRQ handler we should not return normal error codes as 'irqreturn_t'
is expected.
Not necessary to apply to stable as the original check cannot fail and
as such the bug cannot actually occur.
Fixes: 5eda3550a3 ("staging:iio:adis16400: Preallocate transfer message")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210422101911.135630-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On an IRQ handler we should not return normal error codes as 'irqreturn_t'
is expected.
Not necessarily stable material as the old check cannot fail, so it's a bug
we can not hit.
Fixes: ccd2b52f4a ("staging:iio: Add common ADIS library")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210422101911.135630-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When setting the gyro or accelerometer scale the inv_mpu6050 driver ignores
the integer part of the value. As a result e.g. all of 0.13309, 1.13309,
12345.13309, ... are accepted as a valid gyro scale and 0.13309 is the
scale that gets set in all those cases.
Make sure to check that the integer part of the scale value is 0 and reject
it otherwise.
Fixes: 09a642b785 ("Invensense MPU6050 Device Driver.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210405114441.24167-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a bit involved as the adis library code already has some
sanity checking of the flags of the requested irq that we need
to ensure is happy to pass through the IRQF_NO_AUTOEN flag untouched.
Using this flag avoids us autoenabling the irq in the adis16460 and
adis16475 drivers which cover parts that don't have any means of
masking the interrupt on the device end.
Note, compile tested only!
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-7-jic23@kernel.org
The inv_mpu6050 driver requires an interrupt for buffered capture. But non
buffered reading for measurements works just fine without an interrupt
connected.
Make the interrupt optional to support this case.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210325131046.13383-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The inv_mpu6050 driver manually assigns the indio_dev->modes property. But
this is not necessary since it will be setup in iio_trigger_buffer_setup().
Remove the manual assignment.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210325131046.13383-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It may happen that the MPU6050 is the only hardware
trigger available on your system such as this:
> lsiio
Device 003: hscdtd008a
Device 001: mpu6050
Device 002: gp2ap002
Device 000: ab8500-gpadc
Trigger 000: mpu6050-dev1
And when you want to use it to read periodically from
your magnetometer like this:
> iio_generic_buffer -a -c 100 -n hscdtd008a -t mpu6050-dev1
Then the following happens:
[ 209.951334] Internal error: Oops: 5 [#1] SMP ARM
(...)
[ 209.981969] Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support)
[ 209.988925] PC is at inv_scan_query_mpu6050+0x8/0xb8
[ 209.993914] LR is at inv_mpu6050_set_enable+0x40/0x194
This is because since we are not using any channels from the
same device, the indio_dev->active_scan_mask is NULL.
Just checking for that and bailing out is however not enough:
we have to enable some kind of FIFO for the readout to work.
So enable the temperature as a dummy FIFO and all works
fine.
Not suitable for backporting to stable. It is an odd corner case
and does not represent a regression.
Fixes: 09a642b785 ("Invensense MPU6050 Device Driver.")
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210322132408.1003443-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
-----BEGIN PGP SIGNATURE-----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=jeRJ
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of IIO/counter device support, features and cleanup in the 5.13 cycle
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
* tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (119 commits)
iio: acpi_als: Add trigger support
iio: acpi_als: Add local variable dev in probe
iio: acpi_als: Add timestamp channel
iio: adc: ad7292: Modify the bool initialization assignment
iio: cros: unify hw fifo attributes without API changes
iio: kfifo: add devm_iio_triggered_buffer_setup_ext variant
iio: event_monitor: Enable events before monitoring
dt-bindings: iio: adc: Add compatible for Mediatek MT8195
iio:magnetometer: Add Support for ST IIS2MDC
dt-bindings: iio: st,st-sensors add IIS2MDC.
staging: iio: ad9832: kernel-doc fixes
iio:dac:max517.c: Use devm_iio_device_register()
iio:cros_ec_sensors: Fix a wrong function name in kernel doc.
iio: buffer: kfifo_buf: kernel-doc, typo in function name.
iio: accel: sca3000: kernel-doc fixes. Missing - and wrong function names.
iio: adc: adi-axi-adc: Drop false marking for kernel-doc
iio: adc: cpcap-adc: kernel-doc fix - that should be _ in structure name
iio: dac: ad5504: fix wrong part number in kernel-doc structure name.
iio: dac: ad5770r: kernel-doc fix case of letter R wrong in structure name
iio: adc: ti-adc084s021: kernel-doc fixes, missing function names
...
iio_trigger_set_drvdata() sets the trigger device parent to first
argument of viio_trigger_alloc(), no need to do it again in the driver
code.
Remove adis_trigger_setup() to match other drivers where setting the
trigger is usually done in the probe() routine.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-4-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use cocci semantic patch:
@@
expression trigger, P;
@@
trigger = devm_iio_trigger_alloc(P, ...);
...
- trigger->dev.parent = P;
To remove trigger->dev.parent, since it is set by default.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-3-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
adi,ad7949
* Fix a wrong bitmask that could lead to an undefined bit being included.
adi,adi-axi-adc
* Add missing Kconfig dependencies
adi,adis16400
* Wrong error code handling in adis16400 that could lead to failed probe.
hid-sensor-humidity, temperature
* Fix alignment and space for timestamp channel.
hid-sensor-prox
* Fix an issue with handling of exponent on the channel scaling.
invensense,mpu3050
* Fix a hole in error handling.
qcom,spi-vadc
* Correct scaling
st,ab8500-adc
* Fix wrong scaling (by factor of 1000)
st,stm32-adc
* Add missing HAS_IOMEM dependency
st,stm32-timer-cnt
* Report count when running off internal clock
* Fix issue with not checking ceiling before trying to write to hardware
* Ensure driver doesn't have stashed state which doesn't match hardware by
rereading from hardware in a slow path.
-----BEGIN PGP SIGNATURE-----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=L5Yl
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.12a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO and counter fixes for the 5.12 cycle
adi,ad7949
* Fix a wrong bitmask that could lead to an undefined bit being included.
adi,adi-axi-adc
* Add missing Kconfig dependencies
adi,adis16400
* Wrong error code handling in adis16400 that could lead to failed probe.
hid-sensor-humidity, temperature
* Fix alignment and space for timestamp channel.
hid-sensor-prox
* Fix an issue with handling of exponent on the channel scaling.
invensense,mpu3050
* Fix a hole in error handling.
qcom,spi-vadc
* Correct scaling
st,ab8500-adc
* Fix wrong scaling (by factor of 1000)
st,stm32-adc
* Add missing HAS_IOMEM dependency
st,stm32-timer-cnt
* Report count when running off internal clock
* Fix issue with not checking ceiling before trying to write to hardware
* Ensure driver doesn't have stashed state which doesn't match hardware by
rereading from hardware in a slow path.
* tag 'iio-fixes-for-5.12a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
iio: hid-sensor-temperature: Fix issues of timestamp channel
iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
counter: stm32-timer-cnt: fix ceiling write max value
counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
iio: adc: ab8500-gpadc: Fix off by 10 to 3
iio:adc:stm32-adc: Add HAS_IOMEM dependency
iio: adis16400: Fix an error code in adis16400_initial_setup()
iio: adc: adi-axi-adc: add proper Kconfig dependencies
iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
iio: hid-sensor-prox: Fix scale not correct issue
iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel
Add some helpers to lock and unlock the device. As this is such a simple
change, we update all the users that were using the lock already in this
patch.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210218114039.216091-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With this patch, we don't force users to define the IMU scaled internal
sampling rate once in the devicetree. Now it's dynamically calculated
at runtime depending on the desired output rate given by users.
Calculating the sync_scale dynamically gives us better chances of
achieving a perfect/integer value for DEC_RATE (thus giving more
flexibility). The math is:
1. lcm of the input clock and the desired output rate.
2. get the highest multiple of the previous result lower than the adis
max rate.
3. The last result becomes the IMU sample rate. Use that to calculate
SYNC_SCALE and DEC_RATE (to get the user output rate).
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210218114039.216091-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When using PPS mode, the input clock needs to be scaled so that we have
an IMU sample rate between (optimally) 4000 and 4250. After this, we can
use the decimation filter to lower the sampling rate in order to get what
the user wants. Optimally, the user sample rate is a multiple of both the
IMU sample rate and the input clock. Hence, calculating the sync_scale
dynamically gives us better chances of achieving a perfect/integer value
for DEC_RATE. The math here is:
1. lcm of the input clock and the desired output rate.
2. get the highest multiple of the previous result lower than the adis
max rate.
3. The last result becomes the IMU sample rate. Use that to calculate
SYNC_SCALE and DEC_RATE (to get the user output rate).
Fixes: 326e235755 ("iio: imu: adis16480: Add support for external clock")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210218114039.216091-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All drivers that already call devm_iio_kfifo_allocate() &
iio_device_attach_buffer() are simple to convert to
iio_device_attach_kfifo_buffer() in a single go.
This change does that; the unwind order is preserved.
What is important, is that the devm_iio_kfifo_buffer_setup() be called
after the indio_dev->modes is assigned, to make sure that
INDIO_BUFFER_SOFTWARE flag is set and not overridden by the assignment to
indio_dev->modes.
Also, the INDIO_BUFFER_SOFTWARE has been removed from the assignments of
'indio_dev->modes' because it is set by devm_iio_kfifo_buffer_setup().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>x
Link: https://lore.kernel.org/r/20210215104043.91251-4-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is to silence a new Smatch warning:
drivers/iio/imu/adis16400.c:492 adis16400_initial_setup()
warn: sscanf doesn't return error codes
If the condition "if (st->variant->flags & ADIS16400_HAS_SLOW_MODE) {"
is false then we return 1 instead of returning 0 and probe will fail.
Fixes: 72a868b38b ("iio: imu: check sscanf return value")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YCwgFb3JVG6qrlQ+@mwanda
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MPU-6880 seems to be very similar to MPU-6500 and it works
fine with some minor additions for the mpu6050 driver.
Add the necessary defines for it and make it use the same registers
as MPU-6500 but with a FIFO size of 4096.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20201202104656.5119-2-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If we are using edge IRQs, new samples can arrive while processing
current interrupt since there are no hw guarantees the irq line
stays "low" long enough to properly detect the new interrupt.
In this case the new sample will be missed.
Polling FIFO status register in st_lsm6dsx_handler_thread routine
allow us to read new samples even if the interrupt arrives while
processing previous data and the timeslot where the line is "low"
is too short to be properly detected.
Fixes: 89ca88a7cd ("iio: imu: st_lsm6dsx: support active-low interrupts")
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/5e93cda7dc1e665f5685c53ad8e9ea71dbae782d.1605378871.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable array in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver, depending on which channels are enabled, the timestamp
can be in a number of locations. Hence we cannot use a structure
to specify the data layout without it being misleading.
Fixes: 77c4ad2d6a ("iio: imu: Add initial support for Bosch BMI160")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-6-jic23@kernel.org
The comment implies this device has 3 sensor types, but it only
has an accelerometer and a gyroscope (both 3D). As such the
buffer does not need to be as long as stated.
Note I've separated this from the following patch which fixes
the alignment for passing to iio_push_to_buffers_with_timestamp()
as they are different issues even if they affect the same line
of code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-5-jic23@kernel.org
As we no longer support a try again if we cannot reenable the trigger
rename the function to reflect this. Also we don't do anything with
the value returned so stop it returning anything. For the few drivers
that didn't already print an error message in this patch, add such
a print.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Christian Oder <me@myself5.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Nishant Malpani <nish.malpani25@gmail.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Link: https://lore.kernel.org/r/20200920132548.196452-3-jic23@kernel.org
Usual mixed bag of new drivers / device support + cleanups etc with the
addition of a fairly big set of yaml conversions.
Txt to yaml format conversions.
In some cases dropped separate binding and moved to trivial devices (drop).
Listed by manufacturer
- dht11 temperature(drop)
- adi,ad2s90 adi,ad5272 adi,ad5592r adi,ad5758 adi,ad5933 adi,ad7303
adi,adis16480 adi,adf4350
- ams,as3935
- asahi-kasei,ak8974
- atmel,sama5d2-adc
- avago,apds9300 avago,apds9960
- bosch,bma180 bosch,bmc150_magn bosch,bme680 bosch,bmg180
- brcm,iproc-static-adc
- capella,cm36651
- domintech,dmard06(drop)
- fsl,mag3110 fsl,mma8452 fsl,vf610-dac
- hoperf,hp03
- honeywell,hmc5843
- kionix,kxcjk1013
- maxim,ds1803(drop) maxim,ds4424 maxim,max30100 maxim,max30102
maxim,max31856 maxim,max31855k maxim,max44009
maxim,max5481 maxim,max5821
- meas,htu21(drop) meas,ms5367(drop) meas,ms5611 meas,tsys01(drop)
- mediatek,mt2701-auxadc
- melexis,mlx90614 melexis,mlx90632
- memsic,mmc35240(drop)
- microchip,mcp41010 microchip,mcp4131 microchip,mcp4725
- murata,zap2326
- nxp,fxas21002c nxp,lpc1850-dac
- pni,rm3100
- qcom,pm8018-adc qcom,spmi-iadc
- renesas,isl29501 renesas,rcar-gyroadc
- samsung,sensorhub-rinato
- sensiron,sgp30
- sentech,sx9500
- sharp,gp2ap020a00f
- st,hts221 st,lsm6dsx st,st-sensors(many!) st,uvis25 st,vcl53l0x st,vl6180
- ti,adc084s021 ti,ads124s08
ti,dac5571 ti,dac7311 ti,dac7512 ti,dac7612
ti,hdc1000(drop) ti,palmas-gpadc ti,opt3001 ti,tmp07
- upisemi,us51882
- vishay,vcnl4035
- x-powers,axp209
New device support
* adi,ad5685
- Add support for AD5338R dual output 10-bit DAC
- Add DT-binding doc.
* mediatek,mt6360
- New driver for this SoC ADC with bindings and using new channel label
support in the IIO core.
* st,lsm6dsx
- Add support for LSM6DST
Core:
* Add "label" to device channels, provided via a new core callback. Including
DT docs for when that is the source, and ABI docs.
* Add devm_iio_triggered_buffer_setup_ext to take extra attributes.
* dmaengine, unwrap use of iio_buffer_set_attrs()
* Drop iio_buffer_set_attrs()
* Centralize ioctl call handling. Later fix to ensure -EINVAL returned if
no handler has run.
* Fix an issue with IIO_VAL_FRACTIONAL and negative values - doesn't affect
any known existing drivers, but will impact a future one.
* kernel-doc fix in trigger.h
* file-ops ordering cleanup
Features
* semtech,sx9310
- Add control of hardware gain, proximity thresholds, hysteresis and
debounce.
- Increase what information on hardware configuration can be provided
via DT.
Cleanup and minor features
* adi,ad5685
- Add of_match_table
* adi,ad7292
- Drop pointless spi_set_drvdata() call
* adi,ad7298
- Drop platform data and tidy up external reference config.
* adi,ad7303
- Drop platform data handling as unused.
* adi,ad7768
- Add new label attribute for channels provided from dt.
* adi,ad7887
- devm_ usage in probe simplifying remove and error handling.
* adi,adis16201
- Drop pointless spi_set_drvdata() call
* adi,adis16209
- Drop pointless spi_set_drvdata() call
* adi,adis16240
- White space fixup
* adi,adxl372
- use new devm_iio_triggered-buffer_setup_ext()
* amlogic,meson-saradc
- Drop pointless semicolon.
* amstaos,tsl2563
- Put back i2c_device_id table as needed for greybus probing.
* atmel,at91_adc
- Use of_device_get_match_data() instead of open coding it.
- Constify some driver data
- Add KCONFIG dep on CONFIG_OF and drop of_match_ptr()
- Drop platform data as mostly dead code.
- Tidy up reference voltage logic
* atmel-sama5d2
- Drop a pointless semicolon
- Merge buffer and trigger init into a separate function
- Use new devm_iio_triggered_buff_setup_ext()
* avago,apds9960
- Drop a pointless semicolon
* bosch,bmc150
- Drop a pointless semicolon
- Use new iio_triggered_buffer_setup_ext()
* bosch,bmp280
- Drop a pointless semicolon
* fsl,mma8452
- Constification
* (google),cros_ec
- Use new devm_iio_triggered_buffer_setup_ext()
* hid-sensors
- Use new iio_triggered_buffer_setup_ext()
* ingenic,adc
- Drop a pointless semicolon
* invensense,icm426xx
- Fix MAINTAINERS entry missing :
* mediatek,mt6577_audxac
- Add binding doc for mt8516 compatible with mt8173
* motorola,cpcap-adc
- Fix an implicit fallthrough marking that clang needs to avoid warning.
* samsung,exynos-adc
- Stop relying on users counter form input device in ISR.
* st,lsm6dsx
- add vdd and vddio regulator control (including binding update)
* st,stm32-adc
- Tidy up code for dma transfers.
- Adapt clock duty cycle for proper functioning. Note no known problems
with existing boards.
* st,vl53l0x-i2c
- Put back i2c_device_id table as needed for greybus probing.
* vishay,vcnl4035
- Put back i2c_device_id table as needed for greybus probing.
-----BEGIN PGP SIGNATURE-----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=kkcj
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.11a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.11 cycle
Usual mixed bag of new drivers / device support + cleanups etc with the
addition of a fairly big set of yaml conversions.
Txt to yaml format conversions.
In some cases dropped separate binding and moved to trivial devices (drop).
Listed by manufacturer
- dht11 temperature(drop)
- adi,ad2s90 adi,ad5272 adi,ad5592r adi,ad5758 adi,ad5933 adi,ad7303
adi,adis16480 adi,adf4350
- ams,as3935
- asahi-kasei,ak8974
- atmel,sama5d2-adc
- avago,apds9300 avago,apds9960
- bosch,bma180 bosch,bmc150_magn bosch,bme680 bosch,bmg180
- brcm,iproc-static-adc
- capella,cm36651
- domintech,dmard06(drop)
- fsl,mag3110 fsl,mma8452 fsl,vf610-dac
- hoperf,hp03
- honeywell,hmc5843
- kionix,kxcjk1013
- maxim,ds1803(drop) maxim,ds4424 maxim,max30100 maxim,max30102
maxim,max31856 maxim,max31855k maxim,max44009
maxim,max5481 maxim,max5821
- meas,htu21(drop) meas,ms5367(drop) meas,ms5611 meas,tsys01(drop)
- mediatek,mt2701-auxadc
- melexis,mlx90614 melexis,mlx90632
- memsic,mmc35240(drop)
- microchip,mcp41010 microchip,mcp4131 microchip,mcp4725
- murata,zap2326
- nxp,fxas21002c nxp,lpc1850-dac
- pni,rm3100
- qcom,pm8018-adc qcom,spmi-iadc
- renesas,isl29501 renesas,rcar-gyroadc
- samsung,sensorhub-rinato
- sensiron,sgp30
- sentech,sx9500
- sharp,gp2ap020a00f
- st,hts221 st,lsm6dsx st,st-sensors(many!) st,uvis25 st,vcl53l0x st,vl6180
- ti,adc084s021 ti,ads124s08
ti,dac5571 ti,dac7311 ti,dac7512 ti,dac7612
ti,hdc1000(drop) ti,palmas-gpadc ti,opt3001 ti,tmp07
- upisemi,us51882
- vishay,vcnl4035
- x-powers,axp209
New device support
* adi,ad5685
- Add support for AD5338R dual output 10-bit DAC
- Add DT-binding doc.
* mediatek,mt6360
- New driver for this SoC ADC with bindings and using new channel label
support in the IIO core.
* st,lsm6dsx
- Add support for LSM6DST
Core:
* Add "label" to device channels, provided via a new core callback. Including
DT docs for when that is the source, and ABI docs.
* Add devm_iio_triggered_buffer_setup_ext to take extra attributes.
* dmaengine, unwrap use of iio_buffer_set_attrs()
* Drop iio_buffer_set_attrs()
* Centralize ioctl call handling. Later fix to ensure -EINVAL returned if
no handler has run.
* Fix an issue with IIO_VAL_FRACTIONAL and negative values - doesn't affect
any known existing drivers, but will impact a future one.
* kernel-doc fix in trigger.h
* file-ops ordering cleanup
Features
* semtech,sx9310
- Add control of hardware gain, proximity thresholds, hysteresis and
debounce.
- Increase what information on hardware configuration can be provided
via DT.
Cleanup and minor features
* adi,ad5685
- Add of_match_table
* adi,ad7292
- Drop pointless spi_set_drvdata() call
* adi,ad7298
- Drop platform data and tidy up external reference config.
* adi,ad7303
- Drop platform data handling as unused.
* adi,ad7768
- Add new label attribute for channels provided from dt.
* adi,ad7887
- devm_ usage in probe simplifying remove and error handling.
* adi,adis16201
- Drop pointless spi_set_drvdata() call
* adi,adis16209
- Drop pointless spi_set_drvdata() call
* adi,adis16240
- White space fixup
* adi,adxl372
- use new devm_iio_triggered-buffer_setup_ext()
* amlogic,meson-saradc
- Drop pointless semicolon.
* amstaos,tsl2563
- Put back i2c_device_id table as needed for greybus probing.
* atmel,at91_adc
- Use of_device_get_match_data() instead of open coding it.
- Constify some driver data
- Add KCONFIG dep on CONFIG_OF and drop of_match_ptr()
- Drop platform data as mostly dead code.
- Tidy up reference voltage logic
* atmel-sama5d2
- Drop a pointless semicolon
- Merge buffer and trigger init into a separate function
- Use new devm_iio_triggered_buff_setup_ext()
* avago,apds9960
- Drop a pointless semicolon
* bosch,bmc150
- Drop a pointless semicolon
- Use new iio_triggered_buffer_setup_ext()
* bosch,bmp280
- Drop a pointless semicolon
* fsl,mma8452
- Constification
* (google),cros_ec
- Use new devm_iio_triggered_buffer_setup_ext()
* hid-sensors
- Use new iio_triggered_buffer_setup_ext()
* ingenic,adc
- Drop a pointless semicolon
* invensense,icm426xx
- Fix MAINTAINERS entry missing :
* mediatek,mt6577_audxac
- Add binding doc for mt8516 compatible with mt8173
* motorola,cpcap-adc
- Fix an implicit fallthrough marking that clang needs to avoid warning.
* samsung,exynos-adc
- Stop relying on users counter form input device in ISR.
* st,lsm6dsx
- add vdd and vddio regulator control (including binding update)
* st,stm32-adc
- Tidy up code for dma transfers.
- Adapt clock duty cycle for proper functioning. Note no known problems
with existing boards.
* st,vl53l0x-i2c
- Put back i2c_device_id table as needed for greybus probing.
* vishay,vcnl4035
- Put back i2c_device_id table as needed for greybus probing.
* tag 'iio-for-5.11a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (126 commits)
dt-bindings:iio:adc:x-powers,axp209-adc: txt to yaml conversion
dt-bindings:iio:adc:renesas,rcar-gyroadc: txt to yaml conversion.
dt-bindings:iio:adc:atmel,sama5d2-adc: txt to yaml conversion
dt-bindings:iio:magnetometer:pni,rm3100: txt to yaml conversion.
dt-bindings:iio:magnetometer:honeywell,hmc5843: txt to yaml format conversion
dt-bindings:iio:magnetometer:bosch,bmc150_magn: txt to yaml conversion.
dt-bindings:iio:magnetometer:asahi-kasei,ak8974: txt to yaml format conversion
dt-bindings:iio:magnetometer:fsl,mag3110: txt to yaml conversion
dt-bindings:iio:light:st,vl6180: txt to yaml format conversion.
dt-bindings:iio:light:vishay,vcnl4035: txt to yaml conversion
dt-bindings:iio:light:st,uvis25: txt to yaml conversion for this UV sensor
dt-bindings:iio:light:upisemi,us51882: txt to yaml conversion.
dt-bindings:iio:light:ti,opt3001: txt to yaml conversion
dt-bindings:iio:light:maxim,max44009: txt to yaml conversion.
dt-bindings:iio:light:sharp,gp2ap020a00f: txt to yaml conversion.
dt-bindings:iio:light:capella,cm36651: txt to yaml conversion.
dt-bindings:iio:light:avago,apds9960: txt to yaml conversion
dt-bindings:iio:light:avago,apds9300: txt to yaml conversion.
dt-bindings:iio:imu:st,lsm6dsx: txt to yaml conversion
dt-bindings:iio:imu:adi,adis16480: txt to yaml conversion
...
Set 10ms as minimum i2c slave configuration timeout since st_lsm6dsx
relies on accel ODR for i2c master clock and at high sample rates
(e.g. 833Hz or 416Hz) the slave sensor occasionally may need more cycles
than i2c master timeout (2s/833Hz + 1 ~ 3ms) to apply the configuration
resulting in an uncomplete slave configuration and a constant reading
from the i2c slave connected to st_lsm6dsx i2c master.
Fixes: 8f9a5249e3 ("iio: imu: st_lsm6dsx: enable 833Hz sample frequency for tagged sensors")
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/a69c8236bf16a1569966815ed71710af2722ed7d.1604247274.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A break is not needed if it is preceded by a return
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20201019172824.32166-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a couple of changes that apply to large sets of drivers, so
I have grouped those to keep this short.
There are a few late breaking fixes in here that can wait for the
merge window.
dt yaml conversions
-------------------
* adi,ad7768-1
* adi,ad7949
* aspeed,ast2400
* cosmic,10001-adc
* dlg,da9150-gpadc
* fsl,imx25-gcq
* fsl,imx7d-adc
* fsl,vf610
* holt,hi8435
* marvell,berlin2-adc
* motorola,cpcap-adc
* nuvoton,nau7802
* nuvoton,npcm750-adc
* nxp,lpc1850-adc
* nxp,lpc3220
* sprd,sc2720-adc
* st,stmpe-adc
* ti,adc12138
* ti,ads1015
* ti,ads7950
* ti,twl4030-madc
Features
--------
* adxrs290
- Add triggered buffer support and expose data ready signal as a possible
trigger. Includes updating bindings.
- Add debugfs hooks for register access.
* mlx90632
- Add a clear user interface to override the measured ambient temperature.
* vl53l0x
- Add IRQ support including dt bindings.
Cleanups and minor fixes
------------------------
(groups)
Replace mlock with local lock:
* adf4350
* exynos-adc
* fls-imx25-gcq
* stm32-dac
devm use to simplify probe error handling and remove functions.
* adis16201
* adis16203
* adis16209
* adis16240
* adis16136
* adis16260
* adis16400
* adis16460
* adis16480
* adis library - drop unused adis_setup_buffer_and_trigger()
of_match_ptr removal and incorrect ACPI binding removal
of_match_ptr() rarely makes sense in an IIO driver as space saving
is trivial and it breaks ACPI PRP0001 based instantiation.
Mostly this series is about removing examples that get copied into new
drivers.
* ad2s1200
* ad5272
* ad5446
* ad5592r
* ad5593r
* ad5703
* ak8974
* ak8975
* ams-iaq-core
* as3935
* atlas-sensor
* ds1803
* hdc100x
* htu21
* icp10100
* lmp91000
* pulsedlight
* max30102
* max5432
* max5481
* mcp4018
* mcp4131
* mcp4531
* mcp4725
* ms5611
* ms5637
* si7020
* sgp30
* ti-dac082s085
* ti-dac5571
* tmp007
* tsys01
* vz89x
* zpa2326
kernel-doc fixes
* iio-core
* ad7303
* ad7947
* adis16080
* adis16400
* iio_dummy_evgen
* sgp30
Fixes for buffer alignment when passed to iio_push_to_buffers_with_timestamp()
This is a long running effort. There are a few more drivers to come.
* inv_mpu6050
* itg3200
* si1145
* st_lsm6dsx
* ti-adc0832
* ti-adc12138
(not driver focused)
* MAINTAINERS
- Consolidate Analog Device IIO entries whilst removing Beniamin Bia.
- Remove Hartmut Knaack as a listed IIO maintainer as he hasn't been
active for a long time and people are getting intermitted bounces.
* Add __printf() markings to a few functions that were missing them.
* drop some rotted documentation from staging.
* rework buffer sysfs file creation (precursor to multiple buffer support)
(individual drivers)
* ad5592r
- Fix use of true for IIO_SHARED_BY_TYPE
- Tidy up locking and indentation.
* ad9467
- Improve error message on chip-id missmatch.
- Use more appropriate error value if chip-id not recognised.
* adis-library
- Simplify burst mode handling.
* adxrs290
- Make sure to switch device to standby mode during remove.
* as73211
- Increase measurement timeout as seems some devices are slower.
* bma180
- Fix use of true fo IIO_SHARED_BY_TYPE
* exynos_adc
- Update binding to require second interrut with touch screen.
- Update binding to not require syscon on S5Pv210
* hmc5843
- Fix use of true for IIO_SHARED_BY_TYPE
* inv_mpu6050
- Use regmap_noinc_read() for fifo reading.
* palmas_gpadc
- Use module_platform_driver() to remove boilerplate.
* meson-saradc
- style consistency fixes
* rockchip_saradc
- Allow compile testing with !ARM.
* st_lsm6dsx
- Changing scaling factor to use IIO_VAL_INT_PLUS_NANO to improve precision.
- Fix an issue with unchecked return value.
* stm32-adc
- Fix a missing return introduced in dev_err_probe() patch earlier in
cycle.
* sx9310
- Prefer async mode for probe as paticularly slow startup.
* vcnl4000
- Add missing interrupt property to dt binding.
-----BEGIN PGP SIGNATURE-----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=yrII
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.10b-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of features and cleanups for IIO in 5.10
We have a couple of changes that apply to large sets of drivers, so
I have grouped those to keep this short.
There are a few late breaking fixes in here that can wait for the
merge window.
dt yaml conversions
-------------------
* adi,ad7768-1
* adi,ad7949
* aspeed,ast2400
* cosmic,10001-adc
* dlg,da9150-gpadc
* fsl,imx25-gcq
* fsl,imx7d-adc
* fsl,vf610
* holt,hi8435
* marvell,berlin2-adc
* motorola,cpcap-adc
* nuvoton,nau7802
* nuvoton,npcm750-adc
* nxp,lpc1850-adc
* nxp,lpc3220
* sprd,sc2720-adc
* st,stmpe-adc
* ti,adc12138
* ti,ads1015
* ti,ads7950
* ti,twl4030-madc
Features
--------
* adxrs290
- Add triggered buffer support and expose data ready signal as a possible
trigger. Includes updating bindings.
- Add debugfs hooks for register access.
* mlx90632
- Add a clear user interface to override the measured ambient temperature.
* vl53l0x
- Add IRQ support including dt bindings.
Cleanups and minor fixes
------------------------
(groups)
Replace mlock with local lock:
* adf4350
* exynos-adc
* fls-imx25-gcq
* stm32-dac
devm use to simplify probe error handling and remove functions.
* adis16201
* adis16203
* adis16209
* adis16240
* adis16136
* adis16260
* adis16400
* adis16460
* adis16480
* adis library - drop unused adis_setup_buffer_and_trigger()
of_match_ptr removal and incorrect ACPI binding removal
of_match_ptr() rarely makes sense in an IIO driver as space saving
is trivial and it breaks ACPI PRP0001 based instantiation.
Mostly this series is about removing examples that get copied into new
drivers.
* ad2s1200
* ad5272
* ad5446
* ad5592r
* ad5593r
* ad5703
* ak8974
* ak8975
* ams-iaq-core
* as3935
* atlas-sensor
* ds1803
* hdc100x
* htu21
* icp10100
* lmp91000
* pulsedlight
* max30102
* max5432
* max5481
* mcp4018
* mcp4131
* mcp4531
* mcp4725
* ms5611
* ms5637
* si7020
* sgp30
* ti-dac082s085
* ti-dac5571
* tmp007
* tsys01
* vz89x
* zpa2326
kernel-doc fixes
* iio-core
* ad7303
* ad7947
* adis16080
* adis16400
* iio_dummy_evgen
* sgp30
Fixes for buffer alignment when passed to iio_push_to_buffers_with_timestamp()
This is a long running effort. There are a few more drivers to come.
* inv_mpu6050
* itg3200
* si1145
* st_lsm6dsx
* ti-adc0832
* ti-adc12138
(not driver focused)
* MAINTAINERS
- Consolidate Analog Device IIO entries whilst removing Beniamin Bia.
- Remove Hartmut Knaack as a listed IIO maintainer as he hasn't been
active for a long time and people are getting intermitted bounces.
* Add __printf() markings to a few functions that were missing them.
* drop some rotted documentation from staging.
* rework buffer sysfs file creation (precursor to multiple buffer support)
(individual drivers)
* ad5592r
- Fix use of true for IIO_SHARED_BY_TYPE
- Tidy up locking and indentation.
* ad9467
- Improve error message on chip-id missmatch.
- Use more appropriate error value if chip-id not recognised.
* adis-library
- Simplify burst mode handling.
* adxrs290
- Make sure to switch device to standby mode during remove.
* as73211
- Increase measurement timeout as seems some devices are slower.
* bma180
- Fix use of true fo IIO_SHARED_BY_TYPE
* exynos_adc
- Update binding to require second interrut with touch screen.
- Update binding to not require syscon on S5Pv210
* hmc5843
- Fix use of true for IIO_SHARED_BY_TYPE
* inv_mpu6050
- Use regmap_noinc_read() for fifo reading.
* palmas_gpadc
- Use module_platform_driver() to remove boilerplate.
* meson-saradc
- style consistency fixes
* rockchip_saradc
- Allow compile testing with !ARM.
* st_lsm6dsx
- Changing scaling factor to use IIO_VAL_INT_PLUS_NANO to improve precision.
- Fix an issue with unchecked return value.
* stm32-adc
- Fix a missing return introduced in dev_err_probe() patch earlier in
cycle.
* sx9310
- Prefer async mode for probe as paticularly slow startup.
* vcnl4000
- Add missing interrupt property to dt binding.
* tag 'iio-for-5.10b-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (126 commits)
dt-bindings: iio: vishay,vcnl4000: add interrupts property
iio:imu:inv_mpu6050: Use regmap_noinc_read for fifo reads.
iio:imu:inv_mpu6050 Fix dma and ts alignment and data leak issues.
iio:adc:ti-adc12138 Fix alignment issue with timestamp
iio:adc:ti-adc0832 Fix alignment issue with timestamp
iio:imu:st_lsm6dsx Fix alignment and data leak issues
iio:light:si1145: Fix timestamp alignment and prevent data leak.
iio:gyro:itg3200: Fix timestamp alignment and prevent data leak.
iio:imu:st_lsm6dsx: check st_lsm6dsx_shub_read_output return
iio: adc: exynos_adc: Replace indio_dev->mlock with own device lock
dt-bindings:iio:adc:holt,hi8435 yaml conversion
dt-bindings:iio:adc:adi,ad7768-1 yaml conversion
dt-bindings:iio:adc:adi,ad7949 yaml conversion
dt-bindings:iio:adc:dlg,da9150-gpadc yaml conversion
dt-bindings:iio:adc:motorola,cpcap-adc yaml conversion
dt-bindings:iio:adc:nxp,lpc3220-adc yaml conversion
dt-bindings:iio:adc:nxp,lpc1850-adc yaml conversion
dt-bindings:iio:adc:fsl,imx25-gcq yaml conversion
dt-bindings:iio:adc:fsl,imx7d-adc yaml conversion
dt-bindings:iio:adc:ti,ads1015 yaml conversion
...
We should not be assuming that we are reading a sequence of
registers as here we are doing a read of a lot of data from
a single register address.
Not marked for stable as by coincidence it being wrong doesn't
make any difference.
Suggested-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20200722155103.979802-19-jic23@kernel.org
This case is a bit different to the rest of the series. The driver
was doing a regmap_bulk_read into a buffer that wasn't dma safe
as it was on the stack with no guarantee of it being in a cacheline
on it's own. Fixing that also dealt with the data leak and
alignment issues that Lars-Peter pointed out.
Also removed some unaligned handling as we are now aligned.
Fixes tag is for the dma safe buffer issue. Potentially we would
need to backport timestamp alignment futher but that is a totally
different patch.
Fixes: fd64df16f4 ("iio: imu: inv_mpu6050: Add SPI support for MPU6000")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200722155103.979802-18-jic23@kernel.org
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to an array of suitable structures in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart from
previous readings.
For the tagged path the data is aligned by using __aligned(8) for
the buffer on the stack.
There has been a lot of churn in this driver, so likely backports
may be needed for stable.
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200722155103.979802-17-jic23@kernel.org
Potential error return is not checked. This can lead to use
of undefined data.
Detected by clang static analysis.
st_lsm6dsx_shub.c:540:8: warning: Assigned value is garbage or undefined
*val = (s16)le16_to_cpu(*((__le16 *)data));
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Tom Rix <trix@redhat.com
Cc: <Stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200809175551.6794-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Scaling factor values for Acc lead to an unacceptable rounding of the
full scale (FS) calculated by some SensorHAL on Android devices. For examples
setting FS to 4g the in_accel_x_scale, in_accel_y_scale and in_accel_z_scale
are 0.001196 on 6 decimal digits and the FS is
0.001196 × ((2^15) − 1) ~= 39.1893 m/s^2.
Android CTS R10 SensorParameterRangeTest test expects a value greater than
39.20 m/s^2 so this test fails (ACCELEROMETER_MAX_RANGE = 4 * 9.80).
Using 9 decimal digits the new scale factor is 0.001196411 and the FS now
is 0.001196411 × ((2^15)−1) ~= 39.2028 m/s^2.
This patch extends to IIO_VAL_INT_PLUS_NANO type the scaling factor to all
IMU devices where SensorParameterRangeTest CTS test fails.
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/1600361236-2285-1-git-send-email-martepisa@gmail.com
Burst mode variables are now part of the `adis_data` struct. The driver
also has now to explicitly define the length of the burst buffer.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20200917155223.218500-4-nuno.sa@analog.com
Burst mode variables are now part of the `adis_data` struct. The driver
also has now to explicitly define the length of the burst buffer.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20200917155223.218500-3-nuno.sa@analog.com
