fou does not really support IPv6 encapsulation. After an UDP socket is
created in fou_create, the encap_rcv callback is set either to fou_udp_recv
or to gue_udp_recv. Both of those unconditionally assume that the received
packet has an IPv4 header and access the data at network_header as it was an
IPv4 header. This leads to IPv6 flow label being interpreted as IP packet
length, etc.
Disallow fou tunnel to be configured as IPv6 until real IPv6 support is
added to fou.
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints developing VRF driver.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree.
In sum, patches to address fallout from the previous round plus updates from
the IPVS folks via Simon Horman, they are:
1) Add a new scheduler to IPVS: The weighted overflow scheduling algorithm
directs network connections to the server with the highest weight that is
currently available and overflows to the next when active connections exceed
the node's weight. From Raducu Deaconu.
2) Fix locking ordering in IPVS, always take rtnl_lock in first place. Patch
from Julian Anastasov.
3) Allow to indicate the MTU to the IPVS in-kernel state sync daemon. From
Julian Anastasov.
4) Enhance multicast configuration for the IPVS state sync daemon. Also from
Julian.
5) Resolve sparse warnings in the nf_dup modules.
6) Fix a linking problem when CONFIG_NF_DUP_IPV6 is not set.
7) Add ICMP codes 5 and 6 to IPv6 REJECT target, they are more informative
subsets of code 1. From Andreas Herz.
8) Revert the jumpstack size calculation from mark_source_chains due to chain
depth miscalculations, from Florian Westphal.
9) Calm down more sparse warning around the Netfilter tree, again from Florian
Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_metrics and inetpeer both have functions to compare inetpeer
addresses. Consolidate into 1 version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inetpeer set,get helpers in tcp_metrics rather than peeking into
the inetpeer_addr struct.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactors a common line into helper function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting. Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.
Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose. However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.
Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so. In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:
2) Packets with a destination IP (DIP) address in the 224.0.0.X
range which are not IGMP must be forwarded on all ports.
IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
echo 1 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 98d1bd802c.
mark_source_chains will not re-visit chains, so
*filter
:INPUT ACCEPT [365:25776]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [217:45832]
:t1 - [0:0]
:t2 - [0:0]
:t3 - [0:0]
:t4 - [0:0]
-A t1 -i lo -j t2
-A t2 -i lo -j t3
-A t3 -i lo -j t4
# -A INPUT -j t4
# -A INPUT -j t3
# -A INPUT -j t2
-A INPUT -j t1
COMMIT
Will compute a chain depth of 2 if the comments are removed.
Revert back to counting the number of chains for the time being.
Reported-by: Cong Wang <cwang@twopensource.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP pacing was added back in linux-3.12, we chose
to apply a fixed ratio of 200 % against current rate,
to allow probing for optimal throughput even during
slow start phase, where cwnd can be doubled every other gRTT.
At Google, we found it was better applying a different ratio
while in Congestion Avoidance phase.
This ratio was set to 120 %.
We've used the normal tcp_in_slow_start() helper for a while,
then tuned the condition to select the conservative ratio
as soon as cwnd >= ssthresh/2 :
- After cwnd reduction, it is safer to ramp up more slowly,
as we approach optimal cwnd.
- Initial ramp up (ssthresh == INFINITY) still allows doubling
cwnd every other RTT.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Directs route lookups to VRF table. Compiles out if NET_VRF is not
enabled. With this patch able to successfully bring up ipsec tunnels
in VRFs, even with duplicate network configuration.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slow start after idle might reduce cwnd, but we perform this
after first packet was cooked and sent.
With TSO/GSO, it means that we might send a full TSO packet
even if cwnd should have been reduced to IW10.
Moving the SSAI check in skb_entail() makes sense, because
we slightly reduce number of times this check is done,
especially for large send() and TCP Small queue callbacks from
softirq context.
As Neal pointed out, we also need to perform the check
if/when receive window opens.
Tested:
Following packetdrill test demonstrates the problem
// Test of slow start after idle
`sysctl -q net.ipv4.tcp_slow_start_after_idle=1`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 65535 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.100 < . 1:1(0) ack 1 win 511
+0 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_SOCKET, SO_SNDBUF, [200000], 4) = 0
+0 write(4, ..., 26000) = 26000
+0 > . 1:5001(5000) ack 1
+0 > . 5001:10001(5000) ack 1
+0 %{ assert tcpi_snd_cwnd == 10 }%
+.100 < . 1:1(0) ack 10001 win 511
+0 %{ assert tcpi_snd_cwnd == 20, tcpi_snd_cwnd }%
+0 > . 10001:20001(10000) ack 1
+0 > P. 20001:26001(6000) ack 1
+.100 < . 1:1(0) ack 26001 win 511
+0 %{ assert tcpi_snd_cwnd == 36, tcpi_snd_cwnd }%
+4 write(4, ..., 20000) = 20000
// If slow start after idle works properly, we should send 5 MSS here (cwnd/2)
+0 > . 26001:31001(5000) ack 1
+0 %{ assert tcpi_snd_cwnd == 10, tcpi_snd_cwnd }%
+0 > . 31001:36001(5000) ack 1
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cfg and family arguments to lwt build state functions. cfg is a void
pointer and will either be a pointer to a fib_config or fib6_config
structure. The family parameter indicates which one (either AF_INET
or AF_INET6).
LWT encpasulation implementation may use the fib configuration to build
the LWT state.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do WARN_ON_ONCE instead of WARN_ON in gue_gro_receive when the offload
callcaks are bad (either don't exist or gro_receive is not specified).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote checksum offload GRO did not consider the case that frag0
might be in use. This patch fixes that by accessing headers using the
skb_gro functions and not saving offsets relative to skb->head.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
This is second pull request includes the conflict resolution patch that
resulted from the updates that we got for the conntrack template through
kmalloc. No changes with regards to the previously sent 15 patches.
The following patchset contains Netfilter updates for your net-next tree, they
are:
1) Rework the existing nf_tables counter expression to make it per-cpu.
2) Prepare and factor out common packet duplication code from the TEE target so
it can be reused from the new dup expression.
3) Add the new dup expression for the nf_tables IPv4 and IPv6 families.
4) Convert the nf_tables limit expression to use a token-based approach with
64-bits precision.
5) Enhance the nf_tables limit expression to support limiting at packet byte.
This comes after several preparation patches.
6) Add a burst parameter to indicate the amount of packets or bytes that can
exceed the limiting.
7) Add netns support to nfacct, from Andreas Schultz.
8) Pass the nf_conn_zone structure instead of the zone ID in nf_tables to allow
accessing more zone specific information, from Daniel Borkmann.
9) Allow to define zone per-direction to support netns containers with
overlapping network addressing, also from Daniel.
10) Extend the CT target to allow setting the zone based on the skb->mark as a
way to support simple mappings from iptables, also from Daniel.
11) Make the nf_tables payload expression aware of the fact that VLAN offload
may have removed a vlan header, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow specification of per route IP tunnel instructions also for IPv6.
This complements commit 3093fbe7ff ("route: Per route IP tunnel metadata
via lightweight tunnel").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
CC: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the ipv4_tos and ipv4_ttl fields to just 'tos' and 'ttl', as they'll
be used with IPv6 tunnels, too.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IPv6 addresses as an union with IPv4 ones. When using IPv4, the
newly introduced padding after the IPv4 addresses needs to be zeroed out.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas reported breakage adding routes with local nexthops:
$ ip route show table main
...
172.28.0.0/24 dev vnf-xe1p0 proto kernel scope link src 172.28.0.16
$ ip route add 10.0.0.0/8 via 172.28.0.32 table 100 dev vnf-xe1p0
RTNETLINK answers: Resource temporarily unavailable
3bfd847203 changed the lookup to use the passed in table but for cases like
this the nexthop is in the local table rather than the passed in table.
Fixes: 3bfd847203 ("net: Use passed in table for nexthop lookups")
Reported-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib_encap_match() static as it isn't used outside the file.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, two routes going through the same tunnel interface are considered
the same even when they are routed to a different host after encapsulation.
This causes all routes added after the first one to have incorrect
encapsulation parameters.
This is nicely visible by doing:
# ip r a 192.168.1.2/32 dev vxlan0 tunnel dst 10.0.0.2
# ip r a 192.168.1.3/32 dev vxlan0 tunnel dst 10.0.0.3
# ip r
[...]
192.168.1.2/32 tunnel id 0 src 0.0.0.0 dst 10.0.0.2 [...]
192.168.1.3/32 tunnel id 0 src 0.0.0.0 dst 10.0.0.2 [...]
Implement the missing comparison function.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The built lwtunnel_state struct has to be freed after comparison.
Fixes: 571e722676 ("ipv4: support for fib route lwtunnel encap attributes")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_proto_csum_replace4,2,16 take a pseudohdr argument which indicates
the checksum field carries a pseudo header. This argument should be a
boolean instead of an int.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the capability to redirect dst input in the same way
that dst output is redirected by LWT.
Also, save the original dst.input and and dst.out when setting up
lwtunnel redirection. These can be called by the client as a pass-
through.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds the possibility of deriving the zone id from the skb->mark
field in a scalable manner. This allows for having only a single template
serving hundreds/thousands of different zones, for example, instead of the
need to have one match for each zone as an extra CT jump target.
Note that we'd need to have this information attached to the template as at
the time when we're trying to lookup a possible ct object, we already need
to know zone information for a possible match when going into
__nf_conntrack_find_get(). This work provides a minimal implementation for
a possible mapping.
In order to not add/expose an extra ct->status bit, the zone structure has
been extended to carry a flag for deriving the mark.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This work adds a direction parameter to netfilter zones, so identity
separation can be performed only in original/reply or both directions
(default). This basically opens up the possibility of doing NAT with
conflicting IP address/port tuples from multiple, isolated tenants
on a host (e.g. from a netns) without requiring each tenant to NAT
twice resp. to use its own dedicated IP address to SNAT to, meaning
overlapping tuples can be made unique with the zone identifier in
original direction, where the NAT engine will then allocate a unique
tuple in the commonly shared default zone for the reply direction.
In some restricted, local DNAT cases, also port redirection could be
used for making the reply traffic unique w/o requiring SNAT.
The consensus we've reached and discussed at NFWS and since the initial
implementation [1] was to directly integrate the direction meta data
into the existing zones infrastructure, as opposed to the ct->mark
approach we proposed initially.
As we pass the nf_conntrack_zone object directly around, we don't have
to touch all call-sites, but only those, that contain equality checks
of zones. Thus, based on the current direction (original or reply),
we either return the actual id, or the default NF_CT_DEFAULT_ZONE_ID.
CT expectations are direction-agnostic entities when expectations are
being compared among themselves, so we can only use the identifier
in this case.
Note that zone identifiers can not be included into the hash mix
anymore as they don't contain a "stable" value that would be equal
for both directions at all times, f.e. if only zone->id would
unconditionally be xor'ed into the table slot hash, then replies won't
find the corresponding conntracking entry anymore.
If no particular direction is specified when configuring zones, the
behaviour is exactly as we expect currently (both directions).
Support has been added for the CT netlink interface as well as the
x_tables raw CT target, which both already offer existing interfaces
to user space for the configuration of zones.
Below a minimal, simplified collision example (script in [2]) with
netperf sessions:
+--- tenant-1 ---+ mark := 1
| netperf |--+
+----------------+ | CT zone := mark [ORIGINAL]
[ip,sport] := X +--------------+ +--- gateway ---+
| mark routing |--| SNAT |-- ... +
+--------------+ +---------------+ |
+--- tenant-2 ---+ | ~~~|~~~
| netperf |--+ +-----------+ |
+----------------+ mark := 2 | netserver |------ ... +
[ip,sport] := X +-----------+
[ip,port] := Y
On the gateway netns, example:
iptables -t raw -A PREROUTING -j CT --zone mark --zone-dir ORIGINAL
iptables -t nat -A POSTROUTING -o <dev> -j SNAT --to-source <ip> --random-fully
iptables -t mangle -A PREROUTING -m conntrack --ctdir ORIGINAL -j CONNMARK --save-mark
iptables -t mangle -A POSTROUTING -m conntrack --ctdir REPLY -j CONNMARK --restore-mark
conntrack dump from gateway netns:
netperf -H 10.1.1.2 -t TCP_STREAM -l60 -p12865,5555 from each tenant netns
tcp 6 431995 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=5555 dport=12865 zone-orig=1
src=10.1.1.2 dst=10.1.1.1 sport=12865 dport=1024
[ASSURED] mark=1 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 431994 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=5555 dport=12865 zone-orig=2
src=10.1.1.2 dst=10.1.1.1 sport=12865 dport=5555
[ASSURED] mark=2 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 299 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=39438 dport=33768 zone-orig=1
src=10.1.1.2 dst=10.1.1.1 sport=33768 dport=39438
[ASSURED] mark=1 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 300 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=32889 dport=40206 zone-orig=2
src=10.1.1.2 dst=10.1.1.1 sport=40206 dport=32889
[ASSURED] mark=2 secctx=system_u:object_r:unlabeled_t:s0 use=2
Taking this further, test script in [2] creates 200 tenants and runs
original-tuple colliding netperf sessions each. A conntrack -L dump in
the gateway netns also confirms 200 overlapping entries, all in ESTABLISHED
state as expected.
I also did run various other tests with some permutations of the script,
to mention some: SNAT in random/random-fully/persistent mode, no zones (no
overlaps), static zones (original, reply, both directions), etc.
[1] http://thread.gmane.org/gmane.comp.security.firewalls.netfilter.devel/57412/
[2] https://paste.fedoraproject.org/242835/65657871/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Table lookup compiles out when VRF is not enabled.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have IFLA_IPTUN_ netlink attributes. The IP_TUN_ attributes look
very similar, yet they serve very different purpose. This is confusing for
anyone trying to implement a user space tool supporting lwt.
As the IP_TUN_ attributes are used only for the lightweight tunnels, prefix
them with LWTUNNEL_IP_ instead to make their purpose clear. Also, it's more
logical to have them in lwtunnel.h together with the encap enum.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-08-17
1) Fix IPv6 ECN decapsulation for IPsec interfamily tunnels.
From Thomas Egerer.
2) Use kmemdup instead of duplicating it in xfrm_dump_sa().
From Andrzej Hajda.
3) Pass oif to the xfrm lookups so that it gets set on the flow
and the resolver routines can match based on oif.
From David Ahern.
4) Add documentation for the new xfrm garbage collector threshold.
From Alexander Duyck.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8133534c76 ("net: limit tcp/udp rmem/wmem to
SOCK_{RCV,SND}BUF_MIN") modified four sysctls to enforce that the values
written to them are not less than SOCK_MIN_{RCV,SND}BUF.
That change causes 4096 to no longer be accepted as a valid value for
'min' in tcp_wmem and udp_wmem_min. 4096 has been the default for both
of those sysctls for a long time, and unfortunately seems to be an
extremely popular setting. This change breaks a large number of sysctl
configurations at Facebook.
That commit referred to b1cb59cf2e ("net: sysctl_net_core: check
SNDBUF and RCVBUF for min length"), which choose to use the SOCK_MIN
constants as the lower limits to avoid nasty bugs. But AFAICS, a limit
of SOCK_MIN_SNDBUF isn't necessary to do that: the BUG_ON cited in the
commit message seems to have happened because unix_stream_sendmsg()
expects a minimum of a full page (ie SK_MEM_QUANTUM) and the math broke,
not because it had less than SOCK_MIN_SNDBUF allocated.
This particular issue doesn't seem to affect TCP however: using a
setting of "1 1 1" for tcp_{r,w}mem works, although it's obviously
suboptimal. SK_MEM_QUANTUM would be a nice minimum, but it's 64K on
some archs, so there would still be breakage.
Since a value of one doesn't seem to cause any problems, we can drop the
minimum 8133534c added to fix this.
This reverts commit 8133534c76.
Fixes: 8133534c76 ("net: limit tcp/udp rmem/wmem to SOCK_MIN...")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sorin Dumitru <sorin@returnze.ro>
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_lookup() forces FIB_LOOKUP_NOREF flag, while fib_table_lookup()
does not.
This patch solves the typical message at reboot time or device
dismantle :
unregister_netdevice: waiting for eth0 to become free. Usage count = 4
Fixes: 3bfd847203 ("net: Use passed in table for nexthop lookups")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing del_timer() with del_timer_sync(), I introduced
a deadlock condition :
reqsk_queue_unlink() is called from inet_csk_reqsk_queue_drop()
inet_csk_reqsk_queue_drop() can be called from many contexts,
one being the timer handler itself (reqsk_timer_handler()).
In this case, del_timer_sync() loops forever.
Simple fix is to test if timer is pending.
Fixes: 2235f2ac75 ("inet: fix races with reqsk timers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmentation cache uses information from the IP header to reassemble
packets. That information can be duplicated across VRFs -- same source
and destination addresses, protocol and id. Handle fragmentation with
VRFs by adding the VRF device index to entries in the cache and the
lookup arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If output device is not specified use VRF device if input device is
enslaved. This is needed to ensure tcp acks and resets go out VRF device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user passes in a table for new routes use that table for nexthop
lookups. Specifically, this solves the case where a connected route does
not exist in the main table, but only another table and then a subsequent
route is added with a next hop using the connected route. ie.,
$ ip route ls
default via 10.0.2.2 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
169.254.0.0/16 dev eth0 scope link metric 1003
192.168.56.0/24 dev eth1 proto kernel scope link src 192.168.56.51
$ ip route ls table 10
1.1.1.0/24 dev eth2 scope link
Without this patch adding a nexthop route fails:
$ ip route add table 10 2.2.2.0/24 via 1.1.1.10
RTNETLINK answers: Network is unreachable
With this patch the route is added successfully.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device associated with a VRF is brought up or down routes
should be added to/removed from the table associated with the VRF.
fib_magic defaults to using the main or local tables. Have it use
the table with the device if there is one.
A part of this is directing prefsrc validations to the correct
table as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
inet_addr_type_dev_table keeps the same semantics as inet_addr_type but
if the passed in device is enslaved to a VRF then the table for that VRF
is used for the lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
