Currently, whenever an erratum workaround is enabled, it will be
applied whether or not the erratum is relevent for the CPU. This
patch changes this - we check the variant and revision fields in the
main ID register to determine which errata to apply.
We also avoid re-applying erratum 460075 if it has already been applied.
Applying this fix in non-secure mode results in the kernel failing to
boot (or even do anything.)
This fixes booting on some ARMv7 based platforms which otherwise
silently fail.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Starting with ARMv6, the CPUs support the BE-8 variant of big-endian
(byte-invariant). This patch adds the core support:
- setting of the BE-8 mode via the CPSR.E register for both kernel and
user threads
- big-endian page table walking
- REV used to rotate instructions read from memory during fault
processing as they are still little-endian format
- Kconfig and Makefile support for BE-8. The --be8 option must be passed
to the final linking stage to convert the instructions to
little-endian
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a comment to the proc-v7.S file for the setting of the
PRRR and NMRR registers. It also sets the PRRR[13:12] bits to 0
(corresponding to the reserved TEX[0]CB encoding 110) to be consistent
with the documentation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The SWP instruction has been deprecated starting with the ARMv6
architecture. On ARMv7 processors with the multiprocessor extensions
(like Cortex-A9), this instruction is disabled by default but it can be
enabled by setting bit 10 in the System Control register. Note that
setting this bit is safe even if the ARMv7 processor has the SWP
instruction enabled by default.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There are additional bits to set for the ARMv7 SMP extensions in the
TTBR registers. The IRGN bits order is counter-intuitive but it allows
software built for the ARMv7 base architecture to run on an
implementation with the MP extensions.
Signed-off-by: Tony Thompson <Anthony.Thompson@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARMv7 SMP hardware can handle the TLB maintenance operations
broadcasting in hardware so that the software can avoid the costly IPIs.
This patch adds the necessary checks (the MMFR3 CPUID register) to avoid
the broadcasting if already supported by the hardware.
(this patch is based on the work done by Tony Thompson @ ARM)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This is a RealView platform supporting core tiles with ARM11MPCore,
Cortex-A8 or Cortex-A9 (multicore) processors. It has support for MMC,
CompactFlash, PCI-E.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch provides a device drivers, which has a omap iommu, with
address mapping APIs between device virtual address(iommu), physical
address and MPU virtual address.
There are 4 possible patterns for iommu virtual address(iova/da) mapping.
|iova/ mapping iommu_ page
| da pa va (d)-(p)-(v) function type
---------------------------------------------------------------------------
1 | c c c 1 - 1 - 1 _kmap() / _kunmap() s
2 | c c,a c 1 - 1 - 1 _kmalloc()/ _kfree() s
3 | c d c 1 - n - 1 _vmap() / _vunmap() s
4 | c d,a c 1 - n - 1 _vmalloc()/ _vfree() n*
'iova': device iommu virtual address
'da': alias of 'iova'
'pa': physical address
'va': mpu virtual address
'c': contiguous memory area
'd': dicontiguous memory area
'a': anonymous memory allocation
'()': optional feature
'n': a normal page(4KB) size is used.
's': multiple iommu superpage(16MB, 1MB, 64KB, 4KB) size is used.
'*': not yet, but feasible.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
[ARM] 5489/1: ARM errata: Data written to the L2 cache can be overwritten with stale data
[ARM] 5490/1: ARM errata: Processor deadlock when a false hazard is created
[ARM] 5487/1: ARM errata: Stale prediction on replaced interworking branch
[ARM] 5488/1: ARM errata: Invalidation of the Instruction Cache operation can fail
davinci: DM644x: NAND: update partitioning
davinci: update DM644x support in preparation for more SoCs
davinci: DM644x: rename board file
davinci: update pin-multiplexing support
davinci: serial: generalize for more SoCs
davinci: DM355 IRQ Definitions
davinci: DM646x: add interrupt number and priorities
davinci: PSC: Clear bits in MDCTL reg before setting new bits
davinci: gpio bugfixes
davinci: add EDMA driver
davinci: timers: use clk_get_rate()
[ARM] pxa/littleton: add missing da9034 touchscreen support
[ARM] pxa/zylonite: configure GPIO18/19 correctly, used by 2 GPIO expanders
[ARM] pxa/zylonite: fix the issue of unused SDATA_IN_1 pin get AC97 not working
[ARM] pxa: make ads7846 on corgi and spitz to sync on HSYNC
[ARM] pxa: remove unused CPU_FREQ_PXA Kconfig symbol
...
This patch is a workaround for the 460075 Cortex-A8 (r2p0) erratum. It
configures the L2 cache auxiliary control register so that the Write
Allocate mode for the L2 cache is disabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a workaround for the 458693 Cortex-A8 (r2p0)
erratum. It sets the corresponding bits in the auxiliary control
register so that the PLD instruction becomes a NOP.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the workaround for the 430973 Cortex-A8 (r1p0..r1p2)
erratum. The BTAC/BTB is now flushed at every context switch.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements the recommended workaround for erratum 411920
(ARM1136, ARM1156, ARM1176).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This hooks the U300 support into Kbuild and makes a small hook
in mmu.c for supporting an odd memory alignment with shared memory
on these systems.
This is rebased to RMK:s GIT HEAD. This patch tries to add the
Kconfig option in alphabetic order by option text and the Makefile
entry after config symbol.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm is placing some code in the .text.init section, but it does not
reference that section in its linker scripts.
This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because of an ARM1136 erratum (326103), the current v6_early_abort
function needs to set the correct FSR[11] value which determines whether
the data abort was caused by a read or write. For legacy reasons (bit 10
not handled by software), bit 10 was also cleared masking out imprecise
aborts on ARMv6 CPUs. This patch removes the clearing of bit 10 of FSR.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I get random oopses on my Kirkwood board at startup when L2 cache is
enabled. FYI I'm using Marvell uboot version 3.4.16
Each boot produces the same oops, but anything that changes the kernel
size (even only changing initramfs) makes the oops different.
I noticed that nothing invalidates the L2 cache before enabling it,
doing so fixes my problem.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Compiling recent 2.6.29-rc kernels for ARM gives me the following warning:
arch/arm/mm/mmu.c: In function 'sanity_check_meminfo':
arch/arm/mm/mmu.c:697: warning: comparison between pointer and integer
This is because commit 3fd9825c42
"[ARM] 5402/1: fix a case of wrap-around in sanity_check_meminfo()"
in 2.6.29-rc5-git4 added a comparison of a pointer with PAGE_OFFSET,
which is an integer.
Fixed by casting PAGE_OFFSET to void *.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds support for Faraday FA526 core. This core is used at least by:
Cortina Systems Gemini and Centroid family
Cavium Networks ECONA family
Grain Media GM8120
Pixelplus ImageARM
Prolific PL-1029
Faraday IP evaluation boards
v2:
- move TLB_BTB to separate patch
- update copyrights
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
"""The Marvell® PXA168 processor is the first in a family of application
processors targeted at mass market opportunities in computing and consumer
devices. It balances high computing and multimedia performance with low
power consumption to support extended battery life, and includes a wealth
of integrated peripherals to reduce overall BOM cost .... """
See http://www.marvell.com/featured/pxa168.jsp for more information.
1. Marvell Mohawk core is a hybrid of xscale3 and its own ARM core,
there are many enhancements like instructions for flushing the
whole D-cache, and so on
2. Clock reuses Russell's common clkdev, and added the basic support
for UART1/2.
3. Devices are a bit different from the 'mach-pxa' way, the platform
devices are now dynamically allocated only when necessary (i.e.
when pxa_register_device() is called). Description for each device
are stored in an array of 'struct pxa_device_desc'. Now that:
a. this array of device description is marked with __initdata and
can be freed up system is fully up
b. which means board code has to add all needed devices early in
his initializing function
c. platform specific data can now be marked as __initdata since
they are allocated and copied by platform_device_add_data()
4. only the basic UART1/2/3 are added, more devices will come later.
Signed-off-by: Jason Chagas <chagas@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
VIPT aliasing caches have issues of their own which are not yet handled.
Usage of discard_old_kernel_data() in copypage-v6.c is not highmem ready,
kmap/fixmap stuff doesn't take account of cache colouring, etc.
If/when those issues are handled then this could be reverted.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
On xsc3, L2 cache ops are possible only on virtual addresses. The code
is rearranged so to have a linear progression requiring the least amount
of pte setups in the highmem case. To protect the virtual mapping so
created, interrupts must be disabled currently up to a page worth of
address range.
The interrupt disabling is done in a way to minimize the overhead within
the inner loop. The alternative would consist in separate code for
the highmem and non highmem compilation which is less preferable.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The choice is between looping over the physical range and performing
single cache line operations, or to map highmem pages somewhere, as
cache range ops are possible only on virtual addresses.
Because L2 range ops are much faster, we go with the later by factoring
the physical-to-virtual address conversion and use a fixmap entry for it
in the HIGHMEM case.
Possible future optimizations to avoid the pte setup cost:
- do the pte setup for highmem pages only
- determine a threshold for doing a line-by-line processing on physical
addresses when the range is small
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is a helper to be used by the DMA mapping API to handle cache
maintenance for memory identified by a page structure instead of a
virtual address. Those pages may or may not be highmem pages, and
when they're highmem pages, they may or may not be virtually mapped.
When they're not mapped then there is no L1 cache to worry about. But
even in that case the L2 cache must be processed since unmapped highmem
pages can still be L2 cached.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The kmap virtual area borrows a 2MB range at the top of the 16MB area
below PAGE_OFFSET currently reserved for kernel modules and/or the
XIP kernel. This 2MB corresponds to the range covered by 2 consecutive
second-level page tables, or a single pmd entry as seen by the Linux
page table abstraction. Because XIP kernels are unlikely to be seen
on systems needing highmem support, there shouldn't be any shortage of
VM space for modules (14 MB for modules is still way more than twice the
typical usage).
Because the virtual mapping of highmem pages can go away at any moment
after kunmap() is called on them, we need to bypass the delayed cache
flushing provided by flush_dcache_page() in that case.
The atomic kmap versions are based on fixmaps, and
__cpuc_flush_dcache_page() is used directly in that case.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is the minimum fixmap interface expected to be implemented by
architectures supporting highmem.
We have a second level page table already allocated and covering
0xfff00000-0xffffffff because the exception vector page is located
at 0xffff0000, and various cache tricks already use some entries above
0xffff0000. Therefore the PTEs covering 0xfff00000-0xfffeffff are free
to be used.
However the XScale cache flushing code already uses virtual addresses
between 0xfffe0000 and 0xfffeffff.
So this reserves the 0xfff00000-0xfffdffff range for fixmap stuff.
The Documentation/arm/memory.txt information is updated accordingly,
including the information about the actual top of DMA memory mapping
region which didn't match the code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The current use of these macros works well when the conversion is
entirely linear. In this case, we can be assured that the following
holds true:
__va(p + s) - s = __va(p)
However, this is not always the case, especially when there is a
non-linear conversion (eg, when there is a 3.5GB hole in memory.)
In this case, if 's' is the size of the region (eg, PAGE_SIZE) and
'p' is the final page, the above is most definitely not true.
So, we must ensure that __va() and __pa() are only used with valid
kernel direct mapped RAM addresses. This patch tweaks the code
to achieve this.
Tested-by: Charles Moschel <fred99@carolina.rr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150
On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a Non-cacheable Normal ARM executable memory type,
MT_MEMORY_NONCACHED.
On OMAP3, this is used for rapid dynamic voltage/frequency scaling in
the VDD2 voltage domain. OMAP3's SDRAM controller (SDRC) is in the
VDD2 voltage domain, and its clock frequency must change along with
voltage. The SDRC clock change code cannot run from SDRAM itself,
since SDRAM accesses are paused during the clock change. So the
current implementation of the DVFS code executes from OMAP on-chip
SRAM, aka "OCM RAM."
If the OCM RAM pages are marked as Cacheable, the ARM cache controller
will attempt to flush dirty cache lines to the SDRC, so it can fill
those lines with OCM RAM instruction code. The problem is that the
SDRC is paused during DVFS, and so any SDRAM access causes the ARM MPU
subsystem to hang.
TI's original solution to this problem was to mark the OCM RAM
sections as Strongly Ordered memory, thus preventing caching. This is
overkill: since the memory is marked as non-bufferable, OCM RAM writes
become needlessly slow. The idea of "Strongly Ordered SRAM" is also
conceptually disturbing. Previous LAKML list discussion is here:
http://www.spinics.net/lists/arm-kernel/msg54312.html
This memory type MT_MEMORY_NONCACHED is used for OCM RAM by a future
patch.
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack. If the store succeeeds this
corrupts r0 in pt_regs. Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the non highmem case, if two memory banks of 1GB each are provided,
the second bank would evade suppression since its virtual base would
be 0. Fix this by disallowing any memory bank which virtual base
address is found to be lower than PAGE_OFFSET.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When there are multiple L1-aliasing userland mappings of the same physical
page, we currently remap each of them uncached, to prevent VIVT cache
aliasing issues. (E.g. writes to one of the mappings not being immediately
visible via another mapping.) However, when we do this remapping, there
could still be stale data in the L2 cache, and an uncached mapping might
bypass L2 and go straight to RAM. This would cause reads from such
mappings to see old data (until the dirty L2 line is eventually evicted.)
This issue is solved by forcing a L2 cache flush whenever the shared page
is made L1 uncacheable.
Ideally, we would make L1 uncacheable and L2 cacheable as L2 is PIPT. But
Feroceon does not support that combination, and the TEX=5 C=0 B=0 encoding
for XSc3 doesn't appear to work in practice.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tomi Valkeinen reports:
Running with latest linux-omap kernel on OMAP3 SDP board, I have
problem with iounmap(). It looks like iounmap() does not properly
free large areas. Below is a test which fails for me in 6-7 loops.
for (i = 0; i < 200; ++i) {
vaddr = ioremap(paddr, size);
if (!vaddr) {
printk("couldn't ioremap\n");
break;
}
iounmap(vaddr);
}
The changes to vmalloc.c weren't reflected in the ARM ioremap
implementation. Turns out the fix is rather simple.
Tested-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tested-by: Matt Gerassimoff <mgeras@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this, the pxa2xx-flash driver cannot be used as a module.
Reported-by: Chris Lawrence <chrisdl@netspace.net.au>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename ARM's struct vm_region so that I can introduce my own global version
for NOMMU. It's feasible that the ARM version may wish to use my global one
instead.
The NOMMU vm_region struct defines areas of the physical memory map that are
under mmap. This may include chunks of RAM or regions of memory mapped
devices, such as flash. It is also used to retain copies of file content so
that shareable private memory mappings of files can be made. As such, it may
be compatible with what is described in the banner comment for ARM's vm_region
struct.
Signed-off-by: David Howells <dhowells@redhat.com>
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ARMv6 and later CPUs, it is possible for userspace processes to
get stuck on a misaligned load or store due to the "ignore fault"
setting; unlike previous CPUs, retrying the instruction without
the 'A' bit set does not always cause the load to succeed.
We have no real option but to default to fixing up alignment faults
on these CPUs, and having the CPU fix up those misaligned accesses
which it can.
Reported-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch adds the necessary definitions and Kconfig entries to enable
Cortex-A9 (ARMv7 SMP) tiles on the RealView/EB board.
Signed-off-by: Jon Callan <Jon.Callan@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Update to use the asm/sections.h header rather than declaring these
symbols ourselves. Change __data_start to _data to conform with the
naming found within asm/sections.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The restriction on !CONFIG_HIGHMEM is unneeded since page tables are
currently never allocated with highmem pages, and actually disable PTE
dump whenever highmem is configured. Let's have a dynamic test to better
describe the current limitation instead.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 8d5796d2ec allows for the vmalloc
area to be resized from the kernel cmdline. Make sure it cannot overlap
with RAM entirely.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make free_area() arguments pfn based, and return number of freed pages.
This will simplify highmem initialization later.
Also, codepages, datapages and initpages are actually codesize, datasize
and initsize.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Doing so will greatly simplify the bootmem initialization code as each
bank is therefore entirely lowmem or highmem with no crossing between
those zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently there are two instances of struct meminfo: one in
kernel/setup.c marked __initdata, and another in mm/init.c with
permanent storage. Let's keep only the later to directly populate
the permanent version from arm_add_memory().
Also move common validation tests between the MMU and non-MMU cases
into arm_add_memory() to remove some duplication. Protection against
overflowing the membank array is also moved in there in order to cover
the kernel cmdline parsing path as well.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In all cases the kaddr is assigned an input register even though it is
modified in the assembly code. Let's assign a new variable to the
modified value and mark those inline asm with volatile otherwise they
get optimized away because the output variable is otherwise not used.
Also fix a few conversion errors in copypage-feroceon.c and
copypage-v4mc.c.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For similar reasons as copy_user_page(), we want to avoid the
additional kmap_atomic if it's unnecessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We used to override the copy_user_page() function. However, this
is not only inefficient, it also causes additional complexity for
highmem support, since we convert from a struct page to a kernel
direct mapped address and back to a struct page again.
Moreover, with highmem support, we end up pointlessly setting up
kmap entries for pages which we're going to remap. So, push the
kmapping down into the copypage implementation files where it's
required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton, remove memzero() - it's not supported
on other architectures so use of it is a potential build breaking bug.
Since the compiler optimizes memset(x,0,n) to __memzero() perfectly
well, we don't miss out on the underlying benefits of memzero().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since WFI may cause the processor to enter a low-power mode, data may
still be in the write buffer. This patch adds a DSB (or DWB) to the
cpu_(v6|v7)_do_idle functions before the WFI.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mikael Pettersson reported:
The 2.6.28-rc kernels fail to detect PCI device 0000:00:01.0
(the first ethernet port) on my Thecus n2100 XScale box.
There is however still a strange "ghost" device that gets partially
detected in 2.6.28-rc2 vanilla.
The IOP321 manual says:
The user designates the memory region containing the OCCDR as
non-cacheable and non-bufferable from the IntelR XScaleTM core.
This guarantees that all load/stores to the OCCDR are only of
DWORD quantities.
Ensure that the OCCDR is so mapped.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Same fix as commit c7cf72dcad: when 'start' and 'end' are less than a
cacheline apart and 'start' is unaligned we are done after cleaning and
invalidating the first cacheline.
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of 73bdf0a60e, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the SMP/nAMP mode setting to __v7_setup and also sets
TTBR to shared page table walks if SMP is enabled. The PTWs are also
marked inner cacheable for both SMP and UP modes (setting this is fine
even if the CPU doesn't support the feature).
Signed-off-by: Jon Callan <Jon.Callan@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The flush_cache_all function on ARMv7 is implemented as a series of
cache operations by set/way. These are not guaranteed to be ordered with
previous memory accesses, requiring a DMB. This patch also adds barriers
for the TLB operations in compressed/head.S
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 40df2d1d "[ARM] Update Xscale and Xscale3 PTE mappings" was
fingered by git-bisect for a boot failure on iop13xx. The change made
L_PTE_MT_WRITETHROUGH mappings L2-uncacheable. Russell points out that
this mapping is used for the vector page. Given the regression, and the
fact this page is used often, restore the old behaviour.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A typo caused these values to be swapped leading to incorrect memory
type attributes.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MSM architecture covers a wider family of chips than just the MSM7X00A.
Move to a more generic name, in perparation for supporting the specific
SoC variants as sub-architectures (ARCH_MSM7X01A, ARCH_MSM722X, etc). This
gives us ARCH_MSM for the (many) common peripherals.
This also removes the unused/obsolete config item MSM7X00A_IDLE.
Signed-off-by: Brian Swetland <swetland@google.com>
ARMv4 (ARM720T) cache flush functions are broken in 2.6.19+ kernels.
The issue was introduced by commit f12d0d7c77
This patch corrects the CPU_CP15 ifdef statements so that they actually
do something.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add minimal Beagle board support. Based on earlier patches
by Syed Mohammed Khasim with some fixes from linux-omap tree.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These instructions were placed in the code directly as opcodes because
early compilers didn't support them. Toolchains supporting ARMv7
understand these instructions and the patch puts the mnemonics back.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... including some comments about the ordering required to bring
sparsemem up. You have to repeatedly guess, test, reguess, try
again and again to work out what the right ordering is. Many
hours later...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide helpers for getting physical addresses or pfns from the
meminfo array, and use them. Move for_each_nodebank() to
asm/setup.h alongside the meminfo structure definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide L_PTE_MT_xxx definitions to describe the memory types that we
use in Linux/ARM. These definitions are carefully picked such that:
1. their LSBs match what is required for pre-ARMv6 CPUs.
2. they all have a unique encoding, including after modification
by build_mem_type_table() (the result being that some have more
than one combination.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are actually only four separate implementations of set_pte_ext.
Use assembler macros to insert code for these into the proc-*.S files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point scattering this around the tree, the parsing
of the parameter might as well live beside the code which uses
it. That also means we can make vmalloc_reserve a static
variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The newly introduced sanity_check_meminfo() function should be
used to collect all validation of the meminfo array, which we
have in bootmem_init(). Move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Make sure that coprocessor instructions for range ops are contiguous
and not reordered.
- s/invalidate_and_disable_dcache/flush_and_disable_dcache/
- Don't re-enable I/D caches if they were not enabled initially.
- Change some masks to shifts for better generated code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
The PTRS_PER_PMD != 1 condition can be evaluated with C code and
optimized at compile time.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per the dma_unmap_* calls, we don't touch the cache when a DMA
buffer transitions from device to CPU ownership. Presently, no
problems have been identified with speculative cache prefetching
which in itself is a new feature in later architectures. We may
have to revisit the DMA API later for these architectures anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Feroceon L2 cache can work in eighther write through or write back mode
on Kirkwood. Add the option to configure this mode according to Kconfig.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/process.c:270:6: warning: symbol 'show_fpregs' was not declared. Should it be static?
This function isn't used, so can be removed.
arch/arm/kernel/setup.c:532:9: warning: symbol 'len' shadows an earlier one
arch/arm/kernel/setup.c:524:6: originally declared here
A function containing two 'len's.
arch/arm/mm/fault-armv.c:188:13: warning: symbol 'check_writebuffer_bugs' was not declared. Should it be static?
arch/arm/mm/mmap.c:122:5: warning: symbol 'valid_phys_addr_range' was not declared. Should it be static?
arch/arm/mm/mmap.c:137:5: warning: symbol 'valid_mmap_phys_addr_range' was not declared. Should it be static?
Missing includes.
arch/arm/kernel/traps.c:71:77: warning: Using plain integer as NULL pointer
arch/arm/mm/ioremap.c:355:46: error: incompatible types in comparison expression (different address spaces)
Sillies.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This declaration specifies the "function" type and size for various
assembly functions, mainly needed for generating the correct branch
instructions in Thumb-2.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than pollute asm/cacheflush.h with the cache type definitions,
move them to asm/cachetype.h, and include this new header where
necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch will truncate and/or ignore memory banks if their kernel
direct mappings would (partially) overlap with the vmalloc area or
the mappings between the vmalloc area and the address space top, to
prevent crashing during early boot if there happens to be more RAM
installed than we are expecting.
Since the start of the vmalloc area is not at a fixed address (but
the vmalloc end address is, via the per-platform VMALLOC_END define),
a default area of 128M is reserved for vmalloc mappings, which can
be shrunk or enlarged by passing an appropriate vmalloc= command line
option as it is done on x86.
On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe000000,
two 512M RAM banks and vmalloc=128M (the default), this patch gives:
Truncating RAM at 20000000-3fffffff to -35ffffff (vmalloc region overlap).
Memory: 512MB 352MB = 864MB total
On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe800000,
two 256M RAM banks and vmalloc=768M, this patch gives:
Truncating RAM at 00000000-0fffffff to -0e7fffff (vmalloc region overlap).
Ignoring RAM at 10000000-1fffffff (vmalloc region overlap).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Riku Voipio <riku.voipio@iki.fi>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform independent header files to arch/arm/include/asm, leaving
those in asm/arch* and asm/plat* alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Claim the initrd memory exclusively, and order other memory
reservations beforehand. This allows us to determine whether
the initrd memory was overwritten, and disable the initrd in
that case.
This avoids a 'bad page state' bug.
Tested-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(20072fd0c9 lost most of its changes
somehow, came from a mbox archive applied with git-am. No idea
what happened. This puts back the missing bits. --rmk)
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems this small label was lost in the last merge. Without it
no CPU type is selected for the MX2 family of processors. And a build
will fail badly...
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The shared mmap code works fine for the test case, which only checked
for two shared maps of the same file. However, three shared maps
result in one mapping remaining cached, resulting in stale data being
visible via that mapping. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Feroceon platforms that have a branch prediction unit, bit 11 of the
cp15 control register controls the BPU. This patch keeps the old value
of this bit instead of always clearing it.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds basic mach support for the mx2 processor family, based
on the original freescale code and adapted to mainline kernel coding
style.
This part adds the global build only.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
This patch adds the I-cache invalidation in update_mmu_cache if the
corresponding vma is marked as executable. It also invalidates the
I-cache if a thread migrates to a CPU it never ran on.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring
(depending on the model) one or two Feroceon CPU cores with 512K of L2
cache and VFP coprocessors running at (depending on the model) between
800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe
interfaces that can each run either in x4 or quad x1 mode, three USB
2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two
TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI
interface, four UARTs, and depending on the model, two or four gigabit
ethernet interfaces.
This patch adds basic support for the platform, and allows booting
on the MV78x00 development board, with functional UARTs, SATA, PCIe,
GigE and USB ports.
Signed-off-by: Stanislav Samsonov <samsonov@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Add support for the Feroceon 88fr571-vd CPU core as found in e.g.
the Marvell Discovery Duo family of ARM SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.
This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
