Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:
generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method
it821x.c:
* if memory allocation fails drive->autotune won't be set
(but there also won't be ->set_pio_mode method in such case)
piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)
However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since cs5520 uses VDMA best PIO mode was tuned anyway by ide_dma_check()
but only if DMA was successfully initialized.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_LEGACY_IRQS host flag to tell ide_pci_setup_ports() to set
hwif->irq to legacy IRQ 14/15 (iff hwif->irq is not already set) and convert
atiixp, piix, serverworks, sis5513 and slc90e66 host drivers to use it.
While at it:
* In piix.c add IDE_HFLAGS_PIIX define and don't use ->init_hwif for MPIIX.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_SERIALIZE host flag to tell ide_pci_setup_ports() to set
hwif/mate->serialized and convert aec62xx, cs5530 and sc1200 host drivers
to use it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead
of hwif->err_stops_fifo. As a side-effect this change fixes
hwif->err_stops_fifo not being restored by ide_hwif_restore().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add DECLARE_ICH_DEV() macro.
While at it:
* Add init_hwif_ich() (->init_hwif method) for ICH controllers.
* Rename init_chipset_piix() to init_chipset_ich() and use it only for
ICH controllers.
* Remove no longer needed piix_is_ichx() helper.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* No need to disable UDMA in ->init_hwif method for ATP850UF (and since we
now always tune PIO it will be disabled by ->set_pio_mode calls anyway).
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge init_setup_{svwks,csb6}() into svwks_init_one().
While at it:
* Remove redundant dev->device checks.
* Operate on a local copy of serverworks_chipsets[] entry.
* Use pci_resource_start().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off pdc20270_get_dev2() helper from init_setup_pdc20270().
* Merge init_setup_{pdcnew,pdc20270,pdc20276}() into pdc202new_init_one().
While at it:
* Change KERN_ level of interrupt fixup message from KERN_WARNING to KERN_INFO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off hpt{374,371,366}_init() helper from init_setup_hpt{374,371,366}().
* Merge init_setup_{374,372n,371,372a,302,366}() into hpt366_init_one().
While at it:
* Use "HPT36x" name for HPT366/HPT368 chipsets.
* Add .chip_name to struct hpt_info and use it to set set d->name.
* Convert .max_ultra in struct hpt_info to .udma_mask and use it to set
d->udma_mask.
* Fix hpt302 to use HPT302_ALLOW_ATA133_6 define.
* Change HPT366/HPT374 interrupt fixup message from KERN_WARNING to KERN_INFO.
* Use the second hpt366_chipsets[] entry for HPT37x chipsets using HPT36x PCI
device ID and fix .enablebits/.host_flags for HPT36x hpt366_chipsets[] entry.
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge init_setup_{aec62xx,aec6x80}() into aec62xx_init_one().
While at it:
* Use id->driver_data instead of dev->device.
* Use ATA_UDMA6 define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so
they were not converted by commit 44c10138fd.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.
* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
method may still override them).
* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.
While at it:
* Use ATA_{UDMA,MWDMA,SWDMA}* defines.
* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.
* serverworks.c: fix DMA masks being set before checking DMA base.
v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Documentation doesn't mention SWDMA and moreover all timings used
for SWDMA modes were over-clocked when compared to ATA spec.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma]. As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_pci_device_t.host_flags u32 and add IDE_HFLAG_CS5520 host flag.
* Pass ide_pci_device_t *d to setup-pci.c::ide_get_or_set_dma_base()
and use d->name instead of hwif->cds->name.
* Set IDE_HFLAG_CS5520 host flag in cs5520 host driver and use it in
ide_get_or_set_dma_base() to find out which PCI BAR to use, remove no longer
needed cs5520.c::cs5520_init_setup_dma() and ide_pci_device_t.init_setup_dma.
This fixes PCI bus-mastering not being checked for CS5510/CS5520 hosts.
v2:
* It is wrong to check simplex bits on CS5510/CS5520 as v1 did.
(Noticed by Alan).
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DECLARE_GENERIC_PCI_DEV() macro to generic IDE PCI host driver
and use it to cleanup generic_chipsets[].
* Remove dead/obsolete code while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The cs5535 uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.
This fixes it by using the new ide_get_paired_drive() helper instead.
Bart: patch description fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The siimage uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.
This fixes it by using the new ide_get_paired_drive() helper instead.
Bart: patch description fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
6723 2000 28 8751 222f drivers/ide/pci/amd74xx.o.before
3833 2000 16 5849 16d9 drivers/ide/pci/amd74xx.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drive->dn is initialized by ide-probe.c::probe_hwif() so no need to do it
in ->init_hwif method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
7129 404 8 7541 1d75 drivers/ide/pci/sis5513.o.before
3916 404 1 4321 10e1 drivers/ide/pci/sis5513.o.after
Additionaly to being bloat the code contained two bugs:
- wrong cable bit was checked (0x0001 instead of 0x8000) on ATA_133 chipsets
- incorrect UDMA cycle time was reported on ATA_100a/ATA_133 chipsets
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ATAPI devices with broken DMA support should be handled by DMA blacklist
and for debugging purposes we have new shiny "hdx=nodma" kernel paremeter.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "hdx=nodma" option allowing user to disallow DMA for a given device.
* Obsolete "ide=nodma" option.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It has been obsoleted since 1 Nov 2004, is valid only when used together with
"ide=nodma" kernel parameter (which makes no sense) and only for aec62xx,
cmd64x, cs5220, generic, hpt366, sl82c105, tc86c001 and triflex host drivers.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This code doesn't use pci_assign_resource() and ide_get_or_set_dma_base() uses
pci_resource_start() to get DMA base address so it has no chance of working.
Moreover this belongs to PCI quirks (in case somebody would like to fix it).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clear prefetch and postwrite for ATAPI devices instead of depending on BIOS.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't force PIO4 when programming UDMA mode (suggested by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
noautodma can now be unexported.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets
->autotune this change shouldn't have any other effect than bringing ide-pmac
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide-cris allows separate PIO and DMA timings, and ide-cris always sets
->autotune this change shouldn't have any other effect than bringing ide-cris
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since sl82c105 re-programs DMA/PIO timings for DMA enable/disable, and sets
->autotune this change shouldn't have any other effect than bringing sl82c105
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add PIO autotune fallback to ->ide_dma_check.
Since cs5530/sc1200 allow separate PIO and DMA timings, and cs5530/sc1200
always set ->autotune this change shouldn't have any other effect than
bringing these drivers in-line with other host drivers wrt ->ide_dma_check
implementations.
* Fix ->ide_dma_check to return "-1" if DMA cannot be set.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove needless setting of drive->using_dma from auide_dma_check().
* Split off auide_mdma_filter() from auide_dma_check().
* Use ide_tune_dma() in auide_dma_check(), this fixes following issues:
- device's DMA capability bit not being checked
- device not being checked against generic DMA blacklist
- transfer mode not being set on device/host
* Add PIO autotune fallback to auide_dma_check().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode().
* ATI controllers allow separate PIO and DMA timings so remove programming
of PIO modes from atiixp_set_dma_mode(). Also remove no longer needed
atiixp_dma_2_pio() helper.
* SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA
mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable
support for SWDMA modes for now.
* Enable support for MWDMA0 mode.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always set ->autotune in init_hwif_sis5513(), this means practically
no change in behavior since PIO was always tuned in ->ide_dma_check
and >autotune was always set for ->dma_base == 0 case.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add sis_ata133_get_base() helper function for obtaining the address of
the drive control registers on chipset_family == ATA_133 chipsets.
* Add three helper functions for programming PIO/MWDMA timings:
- sis_ata16_program_timings() (for ATA_16/33/66/100a chipset families)
- sis_ata100_program_timings() (for ATA_100/133a chipset families)
- sis_ata133_program_timings() (for ATA_133 chipset family)
MWDMA timings are taken from datasheets and they match ATA spec.
* Add generic helper function sis_program_timings() and use it in
->set_pio_mode and ->set_dma_mode methods (previously the driver
depended on BIOS to program the correct MWDMA timings).
* Remove redundant !chipset_family check from init_hwif_sis5513()
(init_chipset_sis5513() guarantees that we will never get here if
chipset_family cannot be determined).
* SWDMA seems to be unsupported by SiS chipsets (no info about SWDMA in
datasheets and for SWDMA0 mode timing requirements are impossible to
fulfill) so remove ->swdma_mask from init_hwif_sis5513() and handling
of SWDMA modes from sis_set_dma_mode().
* Enable DMA support for chipset_family == ATA_16.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch adds id strings for Corsair 1GB (identified as Hyperstone Model1)
inside legacy/ide-cs.c.
It also includes some minor whitespace cleanups.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The patch described by the following excerpt from ChangeLog-2.6.22 makes
it impossible to use UDMA on a Tyan S2707 motherboard (SvrWks CSB5):
commit 2d5eaa6dd7
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Thu May 10 00:01:08 2007 +0200
ide: rework the code for selecting the best DMA transfer mode (v3)
...
This one-line patch against 2.6.23 fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
init_dma_ali15x3() guarantees that hwif->dma_base will never be set for
m5229_revision < 0x20 so remove redundant m5229_revision >= 0x20 check from
init_hwif_common_ali15x3().
While at it remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set hwif->atapi_dma/{ultra,mwdma}_mask and drive->autodma after checking that
->dma_base exists. If ->dma_base is not set (== PCI BAR4 cannot be reserved)
then DMA hooks shouldn't be initialized or bad things will happen.
OTOH hwif->set_{pio,dma}_mode hooks should be set even if hwif->dma_base == 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set hwif->ide_dma_{check,on} and hwif->autodma to 1 after checking that
->dma_base exists. If ->dma_base is not set (== PCI BAR4 cannot be reserved)
then DMA hooks shouldn't be initialized or bad things will happen.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices which don't set word 93 validation bit should be now handled by
ide-iops.c::ivb_list[] and for debugging purposes cable detection can be
completely overriden with "idex=ata66" parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Need to probe slave device first to make it release PDIAG-
(this is required for correct device side cable detection).
Based on libata commit f31f0cc2f0.
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check ide_config_drive_speed() return value.
* While at also call ide_config_drive_speed() if the transfer mode is
XFER_PIO_SLOW (this case happens iff the transfer mode has already been
set on the device by ide-proc.c::set_xfer_rate()) and remove redundant
setting of ->{init,current}_speed.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set transfer mode on the device before programming the host controller for
the new timings (matches what auide_tune_chipset() is doing wrt DMA modes).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "good DMA drives" hack for icside to ide-dma.c::ide_find_dma_mode()
(in the long-term it should be either removed or generalized for all hosts).
* Use ide_tune_dma() in icside.c::icside_dma_check().
This results in the following changes in behavior:
- pre-EIDE SWDMA modes are now also respected
- drive->autodma is checked instead of hwif->autodma
(doesn't really matter as icside sets both to "1")
* Make ide-dma.c::__ide_dma_good_drive() static and drop "__" prefix.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add missing initialization of hwif->autodma and drive->autodma to
pmac_ide_setup_dma().
* Use ide_tune_dma() in pmac_ide_dma_check().
While at it:
* Fix pmac_ide_dma_check() return value if DMA mode is not programmed
(should be "-1" otherwise ide_set_dma() will try to enable DMA).
* Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always
called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if
->ide_dma_check returns "0").
v2:
* No reason to blacklist all ide_floppy devices and the old code was always
enabling DMA anyway (without even programming controller/device if the
device was ide_floppy).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Upper layers are responsible for controlling nIEN so don't clear nIEN after
command execution in pmac_ide_do_setfeature().
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().
While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():
* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.
* Check DRQ_STAT bit (shouldn't be set for good device status).
Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for good device status before executing the command in
pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this).
It is a job of upper layers to guarantee that the device is ready to
accept new command before we get here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off checking of the status register from ide_wait_stat() to
__ide_wait_stat() helper.
* Use the new helper in ide_config_drive_speed(). The only change in the
functionality is that the function now fails if after 20 sec (WAIT_CMD)
device is still busy (BUSY_STAT bit is set) while previously instead of
failing the function continued with checking for the correct device status
(which would give the device additional 10 usec to clear BUSY_STAT bit).
* Remove stale comment for ide_config_drive_speed().
* Remove duplicate comment for ide_wait_stat() from <linux/ide.h>.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer
necessary pmac_ide_{m,u}dma_enable().
* While at it remove some dead code from pmac_ide_dma_check() (leftovers from
conversion to use ide_max_dma_mode()).
There should be no functionality changes caused by this patch.
v2:
* Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check()
(Noticed by Ben).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this
Device Control register messing in pmac_ide_dma_check() is totally unnecessary.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move adjusting of cycle time for devices providing explicit DMA cycle time
from pmac_ide_mdma_enable() to set_timings_mdma().
* Remove no longer needed drive_cycle_time argument.
* BUG() if unsupported speed argument value is passed (shouldn't happen).
* Matching access/recovery timings always exist so remove redundant check.
* Make set_timings_mdma() void.
* Update pmac_ide_tune_chipset()'s comment.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't check check for pmif == NULL (it should never be NULL if we got here).
* Make a local copy of the timings and set the pmif->timings[] only after
setting the transfer mode on the device (otherwise SELECT_DRIVE() call in
pmac_ide_do_setfeature() will program new timings before the transfer mode
is set on the device - this was pointed out by Sergei). This change makes
pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
kauai_lookup_timing() should always return non-zero return value:
* BUG() in kauai_lookup_timing() if the timing info cannot be found.
* Remove code checking for zero return value from all callers.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch removes the unused EXPORT_SYMBOL_GPL(ide_acpi_set_state)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We need to set hwif->chipset or IDE PCI host drivers may try to claim
our ide_hwifs[] slot.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
