Allocate everything in one place so there's a single point
of failure in sky2_up, and sky2_rx_start can no longer fail.
Don't leave the hardware in a partially initialized state in the
case rx ring allocation fails.
As with the old code, the rx ring still needs to be fully
allocated for sky2_up to succeed.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code to calculate receive threshold and packet size out of
sky2_rx_start() so that is can be called from elsewhere easily.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change how FIFO is programmed in jumbo mode (to match vendor driver).
Mostly cosmetic, the only register change is that the bits 22,23
are not programemd used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit is not changed by vendor driver, and should be left alone.
The documentation implies this a debug bit.
0 = WAKE# only asserted when VMAIN not available
1 = WAKE# is depend on wake events and independent of VMAIN.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Wake On Lan code to be similar to vendor driver. The definition
of Y2_HW_WOL_ON is confusing; what it means is transition to firmware SPI
setting when doing power change.
Since same code is done for both shutdown and suspend, use common
code path.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert QPRINTK macros to netif_<level> equivalents.
Expands and standardizes the logging message output.
Removes __func__ from most logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert uses of msg_<type> to netif_<level>(
Remove msg_<type> macros
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the logic a bit, make the message logs a bit more consistent.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging messages sometimes had duplicated "ATL1E" output.
For instance:
ATL1E 0000:03:00.0: ATL1E: eth0 NIC Link is Up<100 Mbps Full Duplex>
is now:
ATL1E 0000:03:00.0: eth0: NIC Link is Up <100 Mbps Full Duplex>
Add some consistency to logging messages
Add some missing \n's to logging messages
Miscellaneous typo spelling corrections
Change atl1e_validate_option argument from pdev to adapter
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Commit 357d46a17e "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002. efx_mdio_reset_mmd() returns a positive value rather than 0
on success. The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.
The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash. Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset to read the eeprom data was missing and
wrong eeprom data was being dumped. This patch fixes this.
>From Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver is supporting multiple generations of the ASIC
don't mention any ASIC generation number.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver is supporting multiple generations of the ASIC
remove ASIC generation information from the driver description.
This information is displayed by modinfo.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain skews the ASIC can support only 16 vlans per interface.
Once the limit is crossed, the ASIC is programmed in vlan promiscuous mode.
Switch off the vlan promiscuous mode once the number of vlans
falls back to the max vlans supported.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple of code optimizations in the Rx path (to avoid a memset).
From: Sathya P <sathyap@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code allows the new mtu to cross the supported value.
This patch fixes the boundary checks.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now flashing both BE2 and BE3 devices is supported.
From: Naresh G <nareshg@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have a virtio detach API (in commit
f9bfbebf34), we don't need to track xmit
skbs in the virio_net driver, which improves transmission performance.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Micrel KSZ884X network driver for KSZ8841/KSZ8842 PCI Ethernet chips.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Micrel KSZ8841/KSZ8842 PCI Ethernet chip support.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new network driver for Micrel KSZ8841/KSZ8842 PCI Ethernet chips. The same driver can run both chips at the same time. It supports IPv4 TCP hardware checksumming and so can use scatter/gather transmission.
The KSZ8842 switch has 2 ports. Some users like to take direct control of those ports. So KSZ8842 has a multiple devices mode in which the driver creates another network device so that users can specify which port to send packets. This mode is enabled by passing the "multi_dev=1" parameter to the driver during loading.
The KSZ884X can receive huge frames with size up to 1916 bytes. To use this feature change the network device MTU from 1500 to 1898.
The KSZ884X driver has 3 packet receive processing functions for the normal mode, multiple devices mode, and huge frame mode. Those functions are identical except for more checking for the new features. In normal programming point of view the huge frame version is the one to use because it covers all the cases, but this is done for performance consideration because the target clients for the KSZ884X chips are embedded systems, which unlike desktop PC may not have powerful CPU.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to am79c961_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "phy_find_first" instead of manual lookup. Also use "phy_connect_direct"
instead of "phy_connect" since we already have phy_device pointer here.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch "use paged Rx" broke AMSDU Rx functionality. If an AP
sends out A-MSDU packets the station will crash. Fix it by linearizing
skbuff for AMSDU packet before handing it to mac80211 since mac80211
doesn't support paged skbuff.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2155
Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support for setting the coverage class in some cases broke
association and data transfer, as it overwrote the initial ACK timeout
value from the initvals with a smaller value.
I don't know why the new value works in 5 GHz (matches the initval
there), but not in 2.4 GHz (initvals use 64us here), so until the
problem is fully understood, the value should be increased again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: hold ref on flip object until it completes
drm/i915: Fix crash while aborting hibernation
drm/i915: Correctly return -ENOMEM on allocation failure in cmdbuf ioctls.
drm/i915: fix pipe source image setting in flip command
drm/i915: fix flip done interrupt on Ironlake
drm/i915: untangle page flip completion
drm/i915: handle FBC and self-refresh better
drm/i915: Increase fb alignment to 64k
drm/i915: Update write_domains on active list after flush.
drm/i915: Rework DPLL calculation parameters for Ironlake
After `for (val = LDO_VOL_MIN_IDX; val <= LDO_VOL_MAX_IDX; val++)', if no break
occurs, val reaches LDO_VOL_MIN_IDX + 1, which is out of bounds for
ldo45_voltage_map[] and ldo123_voltage_map[].
Similarly BUCK_TARGET_VOL_MAX_IDX + 1 is out of bounds for buck_voltage_map[].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the regulator constraints are empty and there is no voltage
reported then nothing will be added to the text displayed for the
constraints, leading to random stack data being printed. This is
unlikely to happen for practical regulators since most will at
least report a voltage but should still be fixed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: Make cciss_seq_show handle holes in the h->drv[] array
cfq-iosched: split seeky coop queues after one slice
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla2xxx: Obtain proper host structure during response-queue processing.
[SCSI] compat_ioct: fix bsg SG_IO
[SCSI] qla2xxx: make msix interrupt handler safe for irq
[SCSI] zfcp: Report FC BSG errors in correct field
[SCSI] mptfusion : mptscsih_abort return value should be SUCCESS instead of value 0.
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (30 commits)
vgaarb: fix incorrect dereference of userspace pointer.
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/vmwgfx: Fix a circular locking dependency bug.
drm/vmwgfx: Drop scanout flag compat and add execbuf ioctl parameter members. Bumps major.
drm/vmwgfx: Report propper framebuffer_{max|min}_{width|height}
drm/vmwgfx: Update the user-space interface.
drm/radeon/kms: fix screen clearing before fbcon.
nouveau: fix state detection with switchable graphics
drm/nouveau: move dereferences after null checks
drm/nv50: make the pgraph irq handler loop like the pre-nv50 version
drm/nv50: delete ramfc object after disabling fifo, not before
drm/nv50: avoid unloading pgraph context when ctxprog is running
drm/nv50: align size of buffer object to the right boundaries.
drm/nv50: disregard dac outputs in nv50_sor_dpms()
drm/nv50: prevent multiple init tables being parsed at the same time
drm/nouveau: make dp auxch xfer len check for reads only
drm/nv40: make INIT_COMPUTE_MEM a NOP, just like nv50
drm/nouveau: Add proper vgaarb support.
drm/nouveau: Fix fbcon on mixed pre-NV50 + NV50 multicard.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cm: Revert association of an RDMA device when binding to loopback
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, apic: Don't use logical-flat mode when CPU hotplug may exceed 8 CPUs
x86-32: Make AT_VECTOR_SIZE_ARCH=2
x86/agp: Fix amd64-agp module initialization regression
x86, doc: Fix minor spelling error in arch/x86/mm/gup.c
Some unused, unsupported debug code existed in the mpc85xx EDAC driver
that resulted in a build failure when CONFIG_EDAC_DEBUG was defined:
drivers/edac/mpc85xx_edac.c: In function 'mpc85xx_mc_err_probe':
drivers/edac/mpc85xx_edac.c:1031: error: implicit declaration of function 'edac_mc_register_mcidev_debug'
drivers/edac/mpc85xx_edac.c:1031: error: 'debug_attr' undeclared (first use in this function)
drivers/edac/mpc85xx_edac.c:1031: error: (Each undeclared identifier is reported only once
drivers/edac/mpc85xx_edac.c:1031: error: for each function it appears in.)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b484625172 ("edac: mpc85xx add
mpc83xx support") accidentally broke how a chip select's first and last
page addresses are calculated. The page addresses are being shifted too
far right by PAGE_SHIFT. This results in errors such as:
EDAC MPC85xx MC1: Err addr: 0x003075c0
EDAC MPC85xx MC1: PFN: 0x00000307
EDAC MPC85xx MC1: PFN out of range!
EDAC MC1: INTERNAL ERROR: row out of range (4 >= 4)
EDAC MC1: CE - no information available: INTERNAL ERROR
The vaule of PAGE_SHIFT is already being taken into consideration during
the calculation of the 'start' and 'end' variables, thus it is not
necessary to account for it again when setting a chip select's first and
last page address.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bug in the multiblock write tests where the written
data is read back for verifying one block at a time. The tests in
mmc_test assumes that all cards are byte addressable.
This will cause the multi block write tests to fail, leading the user of
the mmc_test driver thinking there is something wrong with the sdhci
driver they are testing.
The start address for the block is calculated as: blocknum * 512. For
block addressable cards the blocknum alone should be used.
Signed-off-by: Johan Kristell <johan.kristell@axis.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspending, tpm_infineon calls the generic suspend function of the
TPM framework. However, the TPM framework does not return and the system
hangs upon suspend. When sending the necessary command "TPM_SaveState"
directly within the driver, suspending and resuming works fine.
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An unfortunate "WARNING" in the message amd64_edac dumps when the system
doesn't support DRAM ECC or ECC checking is not enabled in the BIOS
used to trigger kerneloops which qualified the message as an OOPS thus
misleading the users. See, e.g.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/422536http://bugzilla.kernel.org/show_bug.cgi?id=15238
Downgrade the message level to KERN_NOTICE and fix the formulation.
Cc: stable@kernel.org # .32.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
This patch corrects a userspace pointer dereference in the VGA arbiter
in 2.6.32.1.
copy_from_user() is used at line 822 to copy the contents of buf into
kbuf, but a call to strncmp() on line 964 uses buf rather than kbuf. This
problem led to a GPF in strncmp() when X was started on my x86_32 systems.
X triggered the behavior with a write of "target PCI:0000:01:00.0" to
/dev/vga_arbiter.
The patch has been tested against 2.6.32.1 and observed to correct the GPF
observed when starting X or manually writing the string "target
PCI:0000:01:00.0" to /dev/vga_arbiter.
Signed-off-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-linus' of ../drm-next:
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/radeon/kms: fix screen clearing before fbcon.
drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
drm/radeon/kms: change Kconfig text to reflect the new option.
drm/radeon/kms: suspend and resume audio stuff
ATOM appears to return 0x20 which seems to mean some sort of timeout.
retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Driver has gone under significant changes, the version should
reflect that.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds n-tuple filter programming to 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
radeon_copy_dma is only available for r200 or newer cards.
Call to radeon_copy_dma would result to NULL pointer
dereference if benchmarking asic without dma engine.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /home/airlied/kernel/drm-next:
nouveau: fix state detection with switchable graphics
drm/nouveau: move dereferences after null checks
drm/nv50: make the pgraph irq handler loop like the pre-nv50 version
drm/nv50: delete ramfc object after disabling fifo, not before
drm/nv50: avoid unloading pgraph context when ctxprog is running
drm/nv50: align size of buffer object to the right boundaries.
drm/nv50: disregard dac outputs in nv50_sor_dpms()
drm/nv50: prevent multiple init tables being parsed at the same time
drm/nouveau: make dp auxch xfer len check for reads only
drm/nv40: make INIT_COMPUTE_MEM a NOP, just like nv50
drm/nouveau: Add proper vgaarb support.
drm/nouveau: Fix fbcon on mixed pre-NV50 + NV50 multicard.
drivers/gpu/drm/nouveau/nouveau_grctx.c: correct NULL test
drm/nouveau: call ttm_bo_wait with the bo lock held to prevent hang
drm/nouveau: Fixup semaphores on pre-nv50 cards.
drm/nouveau: Add getparam to get available PGRAPH units.
drm/nouveau: Add module options to disable acceleration.
drm/nouveau: fix non-vram notifier blocks
Even if this bumps the version to 1 it does not mean the driver is
out of staging. From what we know this is the last backwards
incompatible change to the driver.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When time-based throttling is implemented, we need to bump minor.
When the old way of detecting scanout is removed, we need to bump major.
In the meantime, this change should not break existing user-space.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Break the largish case for handling receive checksum into a separate
function, and if there is a problem use dev_XXX routines to
show which hardware is the problem.
Turn one corner case into a BUG(). This only happens if the driver
is expecting one behavior but the chip does the old behavior;
only ever saw this when bringing up a new chip type and driver
was buggy.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clone of vendor code to disable ASF on Extreme and Supreme chips.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the resume path to use pci write config for a couple of reasons:
1. pci_write_config_dword() allows for more error
checking of PCI health after resume.
2. better to toggle this register on all chip types, since that
is what vendor driver does.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will prevent things from falling over if the user frees the flip
buffer before we complete the flip, since we'll hold an internal
reference.
Reported-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915) introduced the problem that if s2disk hibernation
is aborted, the system will crash, because i915_pm_freeze() does
nothing, while it should at least reverse some operations carried out
by i915_suspend().
Fix this issue by splitting the i915 suspend into a freeze part a
suspend part, where the latter is not executed before creating a
hibernation image, and the i915 resume into a "low-level" resume part
and a thaw part, where the former is not executed after the image has
been created.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This memset_io was added to debug something way back and got
left behind, memset the fb to black so the borders don't be all white.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MI_DISPLAY_FLIP command needs to be set the same pipe
source image like in pipe source register, e.g source image
size minus one. This fixes screen corrupt issue on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake plane flip interrupt means flip done event already, the
behavior is not like old chips, and perform like other usual interrupt.
So only need to handle flip done event when receiving that interrupt.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When a new page flip is requested, we need to both queue an unpin for
the current framebuffer, and also increment the flip pending count on
the newly submitted buffer.
At flip finish time, we need to unpin the old fb and decrement the flip
pending count on the new buffer.
The old code was conflating the two, and led to hangs when new direct
rendered apps were started, replacing the existing frame buffer. This
patch splits out the buffers and prevents the hangs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
On 945, we need to avoid entering self-refresh if the compressor is
busy, or we may cause display FIFO underruns leading to ugly flicker.
Fixes fdo bug #24314, kernel bug #15043.
Tested-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Julien Cristau <jcristau@debian.org> (fd.o #25371)
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
An untiled framebuffer must be aligned to 64k. This is normally handled
by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
different and do the pinning itself. However, it aligns the buffer
object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
installed onto the output.
Fixes:
KMS error message while initializing modesetting -
render error detected: EIR: 0x10 [i915]
http://bugs.freedesktop.org/show_bug.cgi?id=22936
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Add support for using the libertas_tf driver on a managed
or ad-hoc network.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before changing the status of a buffer with a pending write we will await
upon a new flush for that buffer. So we can take advantage of any flushes
posted whilst the buffer is active and pending processing by the GPU, by
clearing its write_domain and updating its last_rendering_seqno -- thus
saving a potential flush in deep queues and improves flushing behaviour
upon eviction for both GTT space and fences.
In order to reduce the time spent searching the active list for matching
write_domains, we move those to a separate list whose elements are
the buffers belong to the active/flushing list with pending writes.
Orignal patch by Chris Wilson <chris@chris-wilson.co.uk>, forward-ported
by me.
In addition to better performance, this also fixes a real bug. Before
this changes, i915_gem_evict_everything didn't work as advertised. When
the gpu was actually busy and processing request, the flush and subsequent
wait would not move active and dirty buffers to the inactive list, but
just to the flushing list. Which triggered the BUG_ON at the end of this
function. With the more tight dirty buffer tracking, all currently busy and
dirty buffers get moved to the inactive list by one i915_gem_flush operation.
I've left the BUG_ON I've used to prove this in there.
References:
Bug 25911 - 2.10.0 causes kernel oops and system hangs
http://bugs.freedesktop.org/show_bug.cgi?id=25911
Bug 26101 - [i915] xf86-video-intel 2.10.0 (and git) triggers kernel oops
within seconds after login
http://bugs.freedesktop.org/show_bug.cgi?id=26101
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Adam Lantos <hege@playma.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0). Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Got Ironlake DPLL parameter table, which reflects the hardware
optimized values. So this one trys to list DPLL parameters for
different output types, should potential fix clock issue seen
on new Arrandale CPUs.
This fixes DPLL setting failure on one 1920x1080 dual channel
LVDS for Ironlake. Test has also been made on LVDS panels with
smaller size and CRT/HDMI/DP ports for different monitors on
their all supported modes.
Update:
- Change name of double LVDS to dual LVDS.
- Fix SSC 120M reference clock to use the right range.
Cc: CSJ <changsijay@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
i.MX51 babbage board has a FEC ethernet controller
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX51 babbage board has a FEC ethernet controller with this phy.
In the long term we should resurrect the phylib patches for fec.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fec driver was enabling receive buffer descriptor without allocating
the buffers. Make sure the buffer descriptors are initialized to not
start receiving packets.
Open also calls fec_restart after the rx buffers are allocated. With the code
in fec_restart, it zeroes out the buffer descriptors that have just been
setup.
Signed-off-by: Rob Herring <r.herring@freescale.com>
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the following change from commit 6f8372b6 ("RDMA/cm: fix
loopback address support")
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdma_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
It turns out that important apps such as Open MPI depend on
rdma_bind_addr() NOT associating any RDMA device when binding to a
loopback address. Open MPI is being updated to deal with this, but at
least until a new Open MPI release is available, maintain the previous
behavior: allow rdma_bind_addr() to succeed, but do not bind to a
device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cohd_fin has already been verified not to be NULL, so the argument to
BUG_ON cannot be true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If submitting new buffer failed, a wrong descriptor gets completed and it
doesn't check, if a callback is at all defined, which can lead to an Oops. Fix
these bugs and make ipu_update_channel_buffer() void, because it never fails.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch fixes two potential races in the velocity driver:
* Move the ACK and error handler to the interrupt handler. This fixes a
potential race with shared interrupts when the other device interrupts
before the NAPI poll handler has finished. As the velocity driver hasn't
acked it's own interrupt, it will then steal the interrupt from the
other device.
* Use spin_lock_irqsave in velocity_poll. In the current code, the
interrupt handler will deadlock if e.g., the NAPI poll handler is
executing when an interrupt (for another device) comes in since it
tries to take the already held lock.
Also unlock the spinlock only after enabling the interrupt in
velocity_poll.
The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new RTL8187B device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
======
This fix is related to
http://bugzilla.kernel.org/show_bug.cgi?id=15142
but does not address that exact issue.
======
sysfs does like attributes being removed while they are being accessed
(i.e. read or written) and waits for the access to complete.
As accessing some md attributes takes the same lock that is held while
removing those attributes a deadlock can occur.
This patch addresses 3 issues in md that could lead to this deadlock.
Two relate to calling flush_scheduled_work while the lock is held.
This is probably a bad idea in general and as we use schedule_work to
delete various sysfs objects it is particularly bad.
In one case flush_scheduled_work is called from md_alloc (called by
md_probe) called from do_md_run which holds the lock. This call is
only present to ensure that ->gendisk is set. However we can be sure
that gendisk is always set (though possibly we couldn't when that code
was originally written. This is because do_md_run is called in three
different contexts:
1/ from md_ioctl. This requires that md_open has succeeded, and it
fails if ->gendisk is not set.
2/ from writing a sysfs attribute. This can only happen if the
mddev has been registered in sysfs which happens in md_alloc
after ->gendisk has been set.
3/ from autorun_array which is only called by autorun_devices, which
checks for ->gendisk to be set before calling autorun_array.
So the call to md_probe in do_md_run can be removed, and the check on
->gendisk can also go.
In the other case flush_scheduled_work is being called in do_md_stop,
purportedly to wait for all md_delayed_delete calls (which delete the
component rdevs) to complete. However there really isn't any need to
wait for them - they have already been disconnected in all important
ways.
The third issue is that raid5->stop() removes some attribute names
while the lock is held. There is already some infrastructure in place
to delay attribute removal until after the lock is released (using
schedule_work). So extend that infrastructure to remove the
raid5_attrs_group.
This does not address all lockdep issues related to the sysfs
"s_active" lock. The rest can be address by splitting that lockdep
context between symlinks and non-symlinks which hopefully will happen.
Signed-off-by: NeilBrown <neilb@suse.de>
Unset the bit that indicates that a ctxprog can continue at the end.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
ramfc is zero'ed upon destruction, so it's safer to do things in the right
order.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- We need to disable pgraph fifo access before checking the current channel,
otherwise we could still hit a running ctxprog.
- The writes to 0x400500 are already handled by pgraph->fifo_access and are
therefore redundant, moreover pgraph fifo access should not be reenabled
before current context is set as invalid. So remove them altogether.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- In the current situation the padding that is added is dangerous to write
to, userspace could potentially overwrite parts of another bo.
- Depth and stencil buffers are supposed to be large enough in general so
the waste of memory should be acceptable.
- Alternatives are hiding the padding from users or splitting vram into 2
zones.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes DVI+VGA on my 9400, and likely a lot of other configurations that
got broken by the previos DVI-over-DP fix.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With DVI and DP plugged, the DVI clock change interrupts being run can
cause DP link training to fail. This adds a spinlock around init table
parsing to prevent this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The wrong pointer was tested.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a CHPID is offline during a device shutdown the ccw_device_halt|clear
may fail and the qdio device stays in state STOPPED until the shutdown is
finished. If an interrupt occurs before the device is set to INACTIVE
the STOPPED state triggers a WARN_ON in the interrupt handler.
Prevent this WARN_ON by catching the STOPPED state in the interrupt
handler.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Inbound traffic handling may hang if next buffer to check is in
state ERROR, polling is stopped and the final check for further
available inbound buffers disregards buffers in state ERROR.
This patch includes state ERROR when checking availability of
more inbound buffers.
Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the HW checksum state for frames handed to GRO processing.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code was written long ago when it was not possible to
reshape a degraded array. Now it is so the current level of
degraded-ness needs to be taken in to account. Also newly addded
devices should only reduce degradedness if they are deemed to be
in-sync.
In particular, if you convert a RAID5 to a RAID6, and increase the
number of devices at the same time, then the 5->6 conversion will
make the array degraded so the current code will produce a wrong
value for 'degraded' - "-1" to be precise.
If the reshape runs to completion end_reshape will calculate a correct
new value for 'degraded', but if a device fails during the reshape an
incorrect decision might be made based on the incorrect value of
"degraded".
This patch is suitable for 2.6.32-stable and if they are still open,
2.6.31-stable and 2.6.30-stable as well.
Cc: stable@kernel.org
Reported-by: Michael Evans <mjevans1983@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It appears we aren't required to do memory sizing ourselves on nv40
either. NV40 init tables read a strap from PEXTDEV_BOOT_0 into a
CRTC register, and then later use that value to select a memory
configuration (written to PFB_CFG0, just like INIT_COMPUTE_MEM on
earlier cards) with INIT_IO_RESTRICT_PROG.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We used single shared fbops struct and patched it at fb init time with
pointers to the right variant. On mixed multicard, this meant that
it was either sending NV50-style commands to all cards, or NV04-style
commands to all cards.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_gem_ioctl_cpu_prep calls ttm_bo_wait without the bo lock held.
ttm_bo_wait unlocks that lock, and so must be called with it held.
Currently this bug causes libdrm nouveau_bo_busy() to hang the machine.
Signed-off-by: Luca Barbieri <luca at luca-barbieri.com>
Acked-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Apparently, they generate a PFIFO interrupt each time one of the
semaphore methods is executed if its ctxdma wasn't manually marked as
valid. This patch makes it flip the valid bit in response to the
DMA_SEMAPHORE method (which triggers the IRQ even for a valid ctxdma).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On nv50, this will be needed by applications using CUDA to know
how much stack/local memory to allocate.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
noaccel=1 disables all acceleration and doesn't even attempt
initialising PGRAPH+PFIFO, nofbaccel=1 only makes fbcon unaccelerated.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Due to a thinko, these were previously forced to VRAM even if we allocated
them in GART.
This commit fixes that bug, but keeps the previous behaviour of using VRAM
by default until it's been tested properly across more chipsets.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is strange - like really really strange, twilight zone of strange.
VGA ports have DDC buses, but sometimes for some reasons the BIOS
says we don't and we oops - AMD mentioned bios bugs so we'll have
to add quirks.
reported on irc by nirbheek and
https://bugzilla.redhat.com/show_bug.cgi?id=554323
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes a WARN_ON which is triggered
by Poland's country code.
ath: EEPROM regdomain: 0x8268
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: PL
ath: Regpair used: 0x37
-----------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/regd.c:155 ath_regd_init+0x30b
Pid: 12661, comm: firmware/carl91 2.6.33-rc5-wl #18
Call Trace:
[<>] ? warn_slowpath_common+0x76/0x8c
[<>] ? ar9170_reg_notifier+0x0/0x2d [carl9170usb]
[<>] ? ath_regd_init+0x30b/0x377 [ath]
[<>] ? ar9170_register+0x3b3/0x3ca [carl9170usb]
[...]
---[ end trace ]---
Note: Poland is just an example. But it is very likely
that more country codes are affected.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
p54 uses struct ieee80211_tx_queue_stats also internally, so create a new
identical struct p54_tx_queue_stats which the driver can use.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Because ar9170 uses ieee80211_tx_queue_stats internally, create a new
identical struct ar9170_tx_queue_stats which the driver can use.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
mwl8k used struct ieee80211_tx_queue_stats internally to track the queue
lenght. Replace struct ieee80211_tx_queue_stats with a simple len field
in struct mwl8k_tx_queue. Limit and count fields seemed to be unused.
Compile-tested only.
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running directed active scans we currently end up sending both the SSID
probe requests and an additional broadcast one.
This is due to the fact that we always leave the probe request template SSID IE
length to 0. Instead we should set it to the first SSID to scan, and fill the
direct_scan array with the remaining SSIDs to scan for. This way we only send
what we've been asked to: a broadcast probe request when no directed scan is
requested, and directed probe requests otherwise.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing iwl6050_ops->iwl6050_hcmd_utils structure had no pointers to chain
noise functions (gain_computation and chain_noise_reset). As it turns out,
by adding chain_noise_scale (see related patch), there is no need for separate
chain noise function, so simply use iwl6000_ops->iwl5000_hcmd_utils, and
remove those for 6050.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
6x50 device requires a different scaling factor for Rx gain values sent to
device via PHY_CALIBRATION_CMD (CHAIN_NOISE_GAIN_CMD). Rather than create
a new iwlXXXX_gain_computation() function, add new chain_noise_scale member
to struct iwl_cfg, and keep using iwl5000_gain_computation().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrying commands seldomly works, most often the firmware is in a
weird state anyway and needs the device to reset. So it's better
to report the broken state back to user-space.
Also rename command_timer_fn() into lbs_cmd_timeout_handler(),
which better reflect it's usage.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses unit units of 32 usec with txop but wl1251_acx_ac_cfg()
expects it to be usecs. This fortunately didn't cause any severe problems,
only that firmware was using incorrect WMM settings.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas/if_spi.c needs to #include linux/semaphore.h to fix build errors:
drivers/net/wireless/libertas/if_spi.c:59: error: field 'spi_ready' has incomplete type
drivers/net/wireless/libertas/if_spi.c:60: error: field 'spi_thread_terminated' has incomplete type
drivers/net/wireless/libertas/if_spi.c:785: error: implicit declaration of function 'down_interruptible'
drivers/net/wireless/libertas/if_spi.c:787: error: implicit declaration of function 'up'
drivers/net/wireless/libertas/if_spi.c:834: error: implicit declaration of function 'down'
drivers/net/wireless/libertas/if_spi.c:943: error: implicit declaration of function 'sema_init'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitely enable shared interrupt 2 for any core that didn't get a dedicated IRQ
anymore (fallthrough case) and for EXTIF cores to make gpio interrupts work.
Also remove a bogus comment.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If b43 or b43legacy are deauthenticated or disconnected, there is a
possibility that a reconnection is tried with the queues stopped in
mac80211. To prevent this, start the queues before setting
STAT_INITIALIZED.
In b43, a similar change has been in place (twice) in the
wireless_core_init() routine. Remove the duplicate and add similar
code to b43legacy.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
beacons configuration SHOULD be done only if the STA is associated.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For debugging hardware scan trigger/complete
functionality, it was useful to have code in
hwsim that pretends to do a hardware scan.
This code could be extended to actually do the
scan, but for now it was sufficient for me to
only pretend. Since hwsim was written to ease
debugging, it only makes sense to add it to it
permanently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix ondemand to not request targets outside policy limits
[CPUFREQ] Fix use after free of struct powernow_k8_data
[CPUFREQ] fix default value for ondemand governor
iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.
Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Original code incorrectly assumed only status-type-0
IOCBs would be queued to the response-queue, and thus all
entries would safely reference a VHA from the IOCB
'handle.'
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The status FC_CTELS_STATUS_REJECT for all FC BSG errors is not
appropriate. Instead, report -EIO in the result field if there was a
problem in zfcp with the FC BSG request. If the request is good from
our point of view, report result 0, status FC_CTELS_STATUS_OK and let
userspace read the Accept or Reject from the payload (as documented in
scsi_bsg_fc.h).
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
retval should be SUCCESS/FAILED which is defined at scsi.h
retval = 0 is directing wrong return value. It must be retval = SUCCESS.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'v4l_for_linus' of git://linuxtv.org/fixes:
V4L/DVB: dvb-core: fix initialization of feeds list in demux filter
V4L/DVB: dvb_demux: Don't use vmalloc at dvb_dmx_swfilter_packet
V4L/DVB: Fix the risk of an oops at dvb_dmx_release
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Remove superfluous setup_frame_reg call
sh: Don't continue unwinding across interrupts
sh: Setup frame pointer in handle_exception path
sh: Correct the offset of the return address in ret_from_exception
usb: r8a66597-hcd: Fix up spinlock recursion in root hub polling.
usb: r8a66597-hcd: Flush the D-cache for the pipe-in transfer buffers.
A DVB demultiplexer device can be used to set up either a PES filter or
a section filter. In the former case, the ts field of the feed union of
struct dmxdev_filter is used, in the latter case the sec field of the
same union is used.
The ts field is a struct list_head, and is currently initialized in the
open() method of the demux device. When for a given demuxer a section
filter is set up, the sec field is played with, thus if a PES filter
needs to be set up after that the ts field will be corrupted, causing a
kernel oops.
This fix moves the list head initialization to
dvb_dmxdev_pes_filter_set(), so that the ts field is properly
initialized every time a PES filter is set up.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Walls <awalls@radix.net>
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As dvb_dmx_swfilter_packet() is protected by a spinlock, it shouldn't sleep.
However, vmalloc() may call sleep. So, move the initialization of
dvb_demux::cnt_storage field to a better place.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_dmx_init tries to allocate virtual memory for 2 pointers: filter and feed.
If the second vmalloc fails, filter is freed, but the pointer keeps pointing
to the old place. Later, when dvb_dmx_release() is called, it will try to
free an already freed memory, causing an OOPS.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set state of the device as "initializing" during and after cleanup
to ensure that unsolicited data from the device is not passed on.
We especially want to avoid processing new device announcements
"0xaa 0x00" that can come up before we perform reconnect operation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ingo pointed out that we really don't give the user enough warning to make
a decision here. So revise the Kconfig text with a better warning.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 7036251180 ("tty: fix race in tty_fasync") and
commit b04da8bfdf ("fnctl: f_modown should call write_lock_irqsave/
restore") that tried to fix up some of the fallout but was incomplete.
It turns out that we really cannot hold 'tty->ctrl_lock' over calling
__f_setown, because not only did that cause problems with interrupt
disables (which the second commit fixed), it also causes a potential
ABBA deadlock due to lock ordering.
Thanks to Tetsuo Handa for following up on the issue, and running
lockdep to show the problem. It goes roughly like this:
- f_getown gets filp->f_owner.lock for reading without interrupts
disabled, so an interrupt that happens while that lock is held can
cause a lockdep chain from f_owner.lock -> sighand->siglock.
- at the same time, the tty->ctrl_lock -> f_owner.lock chain that
commit 7036251180 introduced, together with the pre-existing
sighand->siglock -> tty->ctrl_lock chain means that we have a lock
dependency the other way too.
So instead of extending tty->ctrl_lock over the whole __f_setown() call,
we now just take a reference to the 'pid' structure while holding the
lock, and then release it after having done the __f_setown. That still
guarantees that 'struct pid' won't go away from under us, which is all
we really ever needed.
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Américo Wang <xiyou.wangcong@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Fix leak of relocs along do_execbuffer error path
drm/i915: slow acpi_lid_open() causes flickering - V2
drm/i915: Disable SR when more than one pipe is enabled
drm/i915: page flip support for Ironlake
drm/i915: Fix the incorrect DMI string for Samsung SX20S laptop
drm/i915: Add support for SDVO composite TV
drm/i915: don't trigger ironlake vblank interrupt at irq install
drm/i915: handle non-flip pending case when unpinning the scanout buffer
drm/i915: Fix the device info of Pineview
drm/i915: enable vblank interrupt on ironlake
drm/i915: Prevent use of uninitialized pointers along error path.
drm/i915: disable hotplug detect before Ironlake CRT detect
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.
I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.
This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the
for loops that use this as a limit count are of the typical form, "for
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages
w/o missing the last one it is necessary for the count to be one greater
than it is. (Specifically, you will miss the +1.5V 3GPIO input with count
= 12 vs. 13.)
Signed-off-by: Ray Copeland <ray.copeland@aprius.com>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The functionality bit vector is always returned as a little-endian
32-bit number by the device, so it must be byte-swapped to the host
endianness.
On the other hand, the delay value is handled by the USB stack, so no
byte swapping is needed on our side.
This fixes bug #15105:
http://bugzilla.kernel.org/show_bug.cgi?id=15105
Reported-by: Jens Richter <jens@richter-stutensee.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jens Richter <jens@richter-stutensee.de>
Cc: Till Harbaum <till@harbaum.org>
Cc: stable@kernel.org
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
ahci: add Acer G725 to broken suspend list
libata: fix ata_id_logical_per_physical_sectors
libata-scsi passthru: fix bug which truncated LBA48 return values
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix r300 vram width calculations
drm/radeon/kms: rs400/480 MC setup is different than r300.
drm/radeon/kms: make initial state of load detect property correct.
drm/radeon/kms: disable HDMI audio for now on rv710/rv730
drm/radeon/kms: don't call suspend path before cleaning up GPU
drivers/gpu/drm/radeon/radeon_combios.c: fix warning
ati_pcigart: fix printk format warning
drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
drm/radeon/kms: move blit initialization after we disabled VGA
It is possible (and expected) for there to be holes in the h->drv[]
array, that is, some elements may be NULL pointers. cciss_seq_show
needs to be made aware of this possibility to avoid an Oops.
To reproduce the Oops which this fixes:
1) Create two "arrays" in the Array Configuratino Utility and
several logical drives on each array.
2) cat /proc/driver/cciss/cciss* in an infinite loop
3) delete some of the logical drives in the first "array."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.
Implement a new rs400 mc idle function to fix this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:
r8a66597_timer() <-- lock taken
r8a66597_root_hub_control()
r8a66597_check_syssts()
usb_hcd_poll_rh_status() <-- acquires the same lock
/* insert death here */
The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:
When the HDC driver writes the data to the transfer buffers it
pollutes the D-cache (unlike DMA drivers where the device writes
the data). If the corresponding pages get mapped into user space,
there are no additional cache flushing operations performed and
this causes random user space faults on architectures with
separate I and D caches (Harvard) or those with aliasing D-cache.
This fixes up crashes during USB boot on SH7724 and others:
http://marc.info/?l=linux-sh&m=126439837308912&w=2
Reported-by: Goda Yusuke <goda.yusuke@renesas.com>
Tested-by: Goda Yusuke <goda.yusuke@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.
Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix ati_pcigart printk format warning:
drivers/gpu/drm/ati_pcigart.c:115: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cache flush is required in case CPU is accessing rendered data.
This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.
v2 Fix comment ordering in r100_fence_ring_emit and remove extra
defines added in first version.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:
http://bugzilla.kernel.org/show_bug.cgi?id=15186
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just reordering this assignment that doesn't depend on any
condition.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the qlge_change_mtu() is never called if the new_mtu is
equal current MTU, due this condition on dev_set_mtu():
if (new_mtu == dev->mtu)
return 0;
So, this block of code is never reached and is being removed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add periodic heartbeat register read to trigger the eeh
recovery process.
We see cases where an eeh error was injected and the slot was
suspended. An asic access attempt is required to flush the recovery process,
but without interrupts the process can stall.
Adding this periodic register read causes the recovery process to begin.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers do this in them manually. Now they can use this function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue that will cause false hangs when using either
82575 or 82580 in legacy interrupt mode. The issue is caused when there is
a slow traffic flow and an "ethtool -r" is executed while using legacy or
MSI interrupts. MSI-X is not affected by this issue due to the fact that
we were already reconfiguring the vectors after reset.
If possible it would be best to push this for net-2.6 since it is resolving
a bug but if that is not possible then net-next-2.6 will be fine.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following a gpu hang, we would leak the relocation buffer. So simply
earrange the error path to always free the relocation buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
