This patch adds a is_static boolean to the switchdev_obj_fdb structure,
in order to set the ndm_state to either NUD_NOARP or NUD_REACHABLE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address in the switchdev_obj_fdb structure is currently represented
as a pointer. Replacing it for a 6-byte array allows switchdev to carry
addresses directly read from hardware registers, not stored by the
switch chip driver (as in Rocker).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a double word "the the"
in Documentation/DocBook/networking.xml and
Documentation/DocBook/networking/API-Wimax-report-rfkill-sw.html.
These files are generated from comment in source, so I had to
fix the typo in net/wimax/io-rfkill.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition in store_rps_map that allows jump label
count in rps_needed to go below zero. This can happen when
concurrently attempting to set and a clear map.
Scenario:
1. rps_needed count is zero
2. New map is assigned by setting thread, but rps_needed count _not_ yet
incremented (rps_needed count still zero)
2. Map is cleared by second thread, old_map set to that just assigned
3. Second thread performs static_key_slow_dec, rps_needed count now goes
negative
Fix is to increment or decrement rps_needed under the spinlock.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sampling rate is 1, the sampling probability is UINT32_MAX. The packet
should be sampled even the prandom32() generate the number of UINT32_MAX.
And none packet need be sampled when the probability is 0.
Signed-off-by: Wenyu Zhang <wenyuz@vmware.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_VXLAN_FLOWBASED is useless without IFLA_VXLAN_COLLECT_METADATA,
so combine them into single IFLA_VXLAN_COLLECT_METADATA flag.
'flowbased' doesn't convey real meaning of the vxlan tunnel mode.
This mode can be used by routing, tc+bpf and ovs.
Only ovs is strictly flow based, so 'collect metadata' is a better
name for this tunnel mode.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan says:
====================
RDS-TCP: Network namespace support
This patch series contains the set of changes to correctly set up
the infra for PF_RDS sockets that use TCP as the transport in multiple
network namespaces.
Patch 1 in the series is the minimal set of changes to allow
a single instance of RDS-TCP to run in any (i.e init_net or other) net
namespace. The changes in this patch set ensure that the execution of
'modprobe [-r] rds_tcp' sets up the kernel TCP sockets
relative to the current netns, so that RDS applications can send/recv
packets from that netns, and the netns can later be deleted cleanly.
Patch 2 of the series further allows multiple RDS-TCP instances,
one per network namespace. The changes in this patch allows dynamic
creation/tear-down of RDS-TCP client and server sockets across all
current and future namespaces.
v2 changes from RFC sent out earlier:
David Ahern comments in patch 1, net_device notifier in patch 2,
patch 3 broken off and submitted separately.
v3: Cong Wang review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register pernet subsys init/stop functions that will set up
and tear down per-net RDS-TCP listen endpoints. Unregister
pernet subusys functions on 'modprobe -r' to clean up these
end points.
Enable keepalive on both accept and connect socket endpoints.
The keepalive timer expiration will ensure that client socket
endpoints will be removed as appropriate from the netns when
an interface is removed from a namespace.
Register a device notifier callback that will clean up all
sockets (and thus avoid the need to wait for keepalive timeout)
when the loopback device is unregistered from the netns indicating
that the netns is getting deleted.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open the sockets calling sock_create_kern() with the correct struct net
pointer, and use that struct net pointer when verifying the
address passed to rds_bind().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-05
This series contains updates to i40e, i40evf and e1000e.
Anjali adds support for x772 devices to i40e and i40evf. With the added
support, x772 supports offloading of the outer UDP transmit and receive
checksum for tunneled packets. Also supports evicting ATR filters in the
hardware, so update the driver with this new feature set.
Raanan provides several fixes for e1000e, first rectifies the Energy
Efficient Ethernet in Sx code so that it only applies to parts that
actually support EEE in Sx. Fix whitespace and moved ICH8 related define
to the proper context. Fixed the ASPM locking which was reported by
Bjorn Helgaas. Fix a workaround implementation for systime which could
experience a large non-linear increment of the systime value when
checking for overflow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The pr_debug family of functions turns into a no-op when -DDEBUG is not
specified, opting instead to call "no_printk", which gets compiled to a
no-op (but retains gcc's nice warnings about printf-style arguments).
The problem with net_dbg_ratelimited is that it is defined to be a
variant of net_ratelimited_function, which expands to essentially:
if (net_ratelimit())
pr_debug(fmt, ...);
When DEBUG is not defined, then this becomes,
if (net_ratelimit())
;
This seems benign, except it isn't. Firstly, there's the obvious
overhead of calling net_ratelimit needlessly, which does quite some book
keeping for the rate limiting. Given that the pr_debug and
net_dbg_ratelimited family of functions are sprinkled liberally through
performance critical code, with developers assuming they'll be compiled
out to a no-op most of the time, we certainly do not want this needless
book keeping. Secondly, and most visibly, even though no debug message
is printed when DEBUG is not defined, if there is a flood of
invocations, dmesg winds up peppered with messages such as
"net_ratelimit: 320 callbacks suppressed". This is because our
aforementioned net_ratelimit() function actually prints this text in
some circumstances. It's especially odd to see this when there isn't any
other accompanying debug message.
So, in sum, it doesn't make sense to have this function's current
behavior, and instead it should match what every other debug family of
functions in the kernel does with !DEBUG -- nothing.
This patch replaces calls to net_dbg_ratelimited when !DEBUG with
no_printk, keeping with the idiom of all the other debug print helpers.
Also, though not strictly neccessary, it guards the call with an if (0)
so that all evaluation of any arguments are sure to be compiled out.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds null dev check for the 'cfg->rc_via_table ==
NEIGH_LINK_TABLE or dev_get_by_index() failed' case
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Schichan says:
====================
test_bpf improvements
Please find below the patch series with my latest changes to test_bpf.
The first patch checks for unexpected NULL generated skbs before
running the filter.
The second patch adds the possibility for tests to generate fragmented
skbs.
The third patch tests LD_ABS and LD_IND on fragmented skbs.
The fourth patch adds the possibility to restrict the tests being run
by specifying the name/id/range of the test(s) to run via module
parameters.
The fifth patch tests LD_ABS and LD_IND on non fragmented skbs with
various sizes and alignments.
The sixth and final patch checks that the interpreter or JIT correctly
resets A and X to 0.
This serie is against today's net-next tree.
Changes in V2:
* move declaration of 'ptr' in if() block in patch 2/6.
* fix various typos in patch 4/6
* rework default init of test_range array and cleanup exclude_test()
return condition in patch 4/6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is mandatory for the JIT or interpreter to reset the A and X
registers to 0 before running the filter. Check that it is the case on
various ALU and JMP instructions.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exerces the LD_ABS and LD_IND instructions for various sizes and
alignments. This also checks that X when used as an offset to a
BPF_IND instruction first in a filter is correctly set to 0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When developping on the interpreter or a particular JIT, it can be
interesting to restrict the tests list to a specific test or a
particular range of tests.
This patch adds the following module parameters to the test_bpf module:
* test_name=<string>: only the specified named test will be run.
* test_id=<number>: only the test with the specified id will be run
(see the output of test_bpf without parameters to get the test id).
* test_range=<number>,<number>: only the tests within IDs in the
specified id range are run (see the output of test_bpf without
parameters to get the test ids).
Any invalid range, test id or test name will result in -EINVAL being
returned and no tests being run.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new tests exercise various load sizes and offsets crossing the
head/fragment boundary.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduce a new test->aux flag (FLAG_SKB_FRAG) to tell the
populate_skb() function to add a fragment to the test skb containing
the data specified in test->frag_data).
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai says:
====================
net/mlx5e: Driver updates 04-Aug-2015
This patchset introduces two features to the ConnectX-4 driver: Patch 8/8
("Support physical port counters") exposes some hardware counters through
ethtool. Rest of the patches are preparation and usage of what we call
light-weight netdev open/close. Some flows that used to be in the ndo_open/stop
are moved to the PCI probe/remove flows - i.e. we will make the netdev
open/close operations more "light-weight".
The benefits of this change are:
1) Reduce the execution time of the stop/open operations.
2) Avoid saving SW shadows of resource configurations that must
persist through stop/open operations (e.g flow table steering
rules), and avoid deleting/applying them from/to the device upon
netdev stop/open.
3) Avoid synchronizing threads that access those resources with the
netdev stop/open threads.
Instead of create/destroy the resource during netdev open/stop, This patchset
changes the behavior such that upon netdev stop, traffic is redirected to a
"Drop RQ" (a RQ that silently drops, at the NIC HW level all incoming traffic).
After redirecting the traffic, RX/TX software resources could be destroyed.
During netdev open, the RX/TX rings are created and traffic is redirected to
the RX rings.
Patchset was applied and tested over commit ba7591d ("ebpf: add skb->hash to
offset map for usage in {cls, act}_bpf or filters")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that TIRs, TISs and flow tables are kept alive while the netdev is
stopped (after executing ndo_stop()) we can do the following
improvements:
- Obsolete the active_vlans SW shadow.
- Do not delete/add flow table rules upon ndo_stop/open.
In addition to simplifying the flow, this change also fastens
the ndo_open/close operations.
- Obsolete synchronization of threads accessing the flow tables
with the netdev stop/open threads.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not make sense to allow events while the netdev is
unregistered.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions that used to be invoked upon ndo_open/stop and
are now invoked upon create/destroy_netdev() in order to better hint
their place in the flow.
Change some functions location in the file so that functions involved
in ndo_open/stop flow will not be interleaved with other functions.
This is a cosmetic change, no logical change here.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX traffic routed to this RQ will be silently dropped, at the NIC HW
level.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally an RX packet flows through the following objects:
Flow table --> TIR --> RQT --> RQ
Where:
- TIR stands for "Transport Interface Receive", defining the RSS and
LRO paramaters.
- RQT stands for "RQ Table", implementing the RSS indirection table.
- RQ stands for "Receive Queue"
For flows that do not need LRO, nor RSS, the driver made a shortcut to
the above RX flow by pointing to the RQ directly from the TIR, yielding
this flow:
Flow table --> TIR --> RQ
In this commit we remove this shortcut by "inserting" a single-RQ RQT
between the TIR and the RQ, i.e RX packets will reach the same RQ but
will go through an RQT of size 1, pointing to just a single RQ.
This way the RX traffic re-direction to/from the "Drop RQ" will be more
uniform (AKA "one flow"), as it will involve only RQTs re-direction and
no TIRs re-direction.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N says:
====================
CPSW interrupt handling cleanup and performance improvement
This patch series removes the irq controller disable interrupt and
adding a napi for tx event handling which improves the performance by
~180Mbps on dra7-evm
[ 5] local 192.168.10.116 port 5001 connected with 192.168.10.165 port 44176
[ 5] 0.0-60.0 sec 1.48 GBytes 210 Mbits/sec
[ 4] local 192.168.10.116 port 5001 connected with 192.168.10.165 port 33257
[ 4] 0.0-60.0 sec 2.71 GBytes 386 Mbits/sec
Changes from initial version:
* Added a patch to have napi only for first interface as there is
no use of having seperate napis for each interface as the
interrupt is shared by both interface and only one napi is
scheduled for each interrupt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]
[1] http://patchwork.ozlabs.org/patch/492741/
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently changed this code from returning NULL to returning ERR_PTR.
There are some left over NULL assignments which we can remove. We can
preserve the error code from ip_route_output() instead of always
returning -ENODEV. Also these functions use a mix of gotos and direct
returns. There is no cleanup necessary so I changed the gotos to
direct returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x, cnic, bnx2fc: add support for BD
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") added support
for a new multi-function mode, but it added only the support required by
bnx2x for L2 interfaces.
This adds the required changes to support the new multi-function mode in
the offloaded storage protocols.
Dave,
Please consider applying this series to `net-next'.
Do notice that this involves non-networking driver changes -
but sending this as a single series seemed like the best approach as
we had to have bnx2x changes to support the new functionality.
If this is problematic, please tell us what's the preferred solution here.
Changes from previous versions
------------------------------
- From v1 - no actual changes; v1 failed to reach netdev so in order to
keep things in line I've termed this one v2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful register_netdev, we can use netdev_err rather the more
generic dev_err.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set port to NULL if port probe fails so we don't try to remove partially
initialized port on port probe err cleanup path.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 does NVM update via the adminq queue, so we need to add support for
that.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports evicting ATR filters in the HW. With this patch, we enable
the feature in the driver and avoid filter deletion by the driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
