The firmware expects the minimum length of
WMI_SEND_PROBE_RESPONSE_CMDID to be 13. However, when the device is a
P2P GO and it needs to send a probe response to a non-P2P client,
there are no P2P IEs to be added, and therefore the length of the WMI
command is 12. This command gets rejected by the firmware. To fix
this, add an extra byte to satisfy the minimum length requirement.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Removed unused WOW_MAX_FILTER_LISTS macro.
* Removed empty ath6kl_wmi_get_wow_list_event_rx() function.
List of configured WOW patterns are maintained in CFG layer
itself. No need to have this function in ath6kl to get
configured WOW pattern list. It can added later if we need
it for debugging.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It will be used in WOW suspend/resume functions to
active/deactivate WOW suspend mode.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These commands will be used in WOW suspend/resume functions
to configure WOW parameters like patterns to be matched
and it's mask value, etc.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no guarantee on the caller using 8-octet buffer for
key->seq, so better follow the key->seq_len parameter on figuring
out how many octets to copy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The following is the lockdep warning which detects possible
deadlock condition with the way ar->lock and ar->list_lock
are being used.
(&(&ar->lock)->rlock){+.-...}, at: [<ffffffffa0492d13>] ath6kl_indicate_tx_activity+0x83/0x110 [ath6kl]
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&(&ar->list_lock)->rlock){+.+...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&ar->list_lock)->rlock);
local_irq_disable();
lock(&(&ar->lock)->rlock);
lock(&(&ar->list_lock)->rlock);
<Interrupt>
lock(&(&ar->lock)->rlock);
*** DEADLOCK ***
softirqs have to be disabled when acquiring ar->list_lock to avoid
the above deadlock condition. When the above warning printed the
interface is still up and running without issue.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wpa_supplicant was receiving incorrect frame contents in the
callback function that indicates the status of the frame transmitted.
This patch fixes a missing copy of the frame contents to a local
buffer. The local buffer keeps track of the last sent management frame.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though only a single concurrent remain-on-channel operation is
supported, there may be two pending remain-on-channel events (one to
indicate end of a canceled operation and another to indicate start of a
new operation). User space won't be able to distinguish these events
unless unique cookies are used.
The previous behavior resulted in wpa_supplicant getting quite
confused about the driver's offchannel state in various sequences
and this made the P2P state machine behave incorrectly. Use of
more than a single remain-on-channel cookie value fixes this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wlan parameters need to be configured for every vif
in target.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch removes all references to ar->vif and takes
vif from a list.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface index is passed in wmi data header as well, use it
to get the corresponding vif structure.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface index is passed in wmi command header from target.
Use this index to get the appropriate vif.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass this index to target in wmi commands to specify the interface
for which the command needs to be handled.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ar->flag maintains interface stats. Move interface
specific states from ar->flag to vif->flags.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to avoid using ar->wdev to get wiphy pointer, this
may need further cleanup for multi vif support.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows RSN pre-authentication to be used when roaming decisions are
done in the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we allow the first Beacon frame after each connection to
be processed at the host, we can figure out the DTIM period and
expose it with Beacon interval through STA info BSS parameters
to user space.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since we may end up using a dummy BSS entry when roaming, allow one Beacon
frame -based bssinfo from the current BSS to be processed prior to starting
to filter all bssinfo events. This allows cfg80211 BSS table to be filled
with proper data in the roaming case where the full Beacon data may not
have been present at the time of roamed event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no point in unconditionally converting the bssinfo header
to the old version since only the new header is being used and the
driver can as well read the values from it when needed. Leaving out
the conversion saves some extra memory copying.
In addition, use the calculated "rssi" value snr - 95 dBm to get the
proper value in cfg80211 BSS table (i.e., something that more or less
matches with the value used in STA info).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that the scan results are reported directly to the cfg80211 BSS
table there is no need for maintaining this internal node table
implementation for scan results. Remove the definitions and node
table functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal node table in ath6kl was not really used for any useful
purpose. It was just used to collect scan results during a scan and then
provide them in a burst to cfg80211 at the completion of the scan. There
is no point in doing this since cfg80211 is perfectly capable of
maintaining the BSS table and the BSS inform messages are sent in
separate function calls anyway.
This provides more complete information in the cfg80211 BSS table since
this allows Beacon and Probe Response frames to be distinguished and IEs
from them reported separately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This event has been deprecated and there is no need for ath6kl to
include code for processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Process the regulatory code from eeprom and pass the
country information to cfg80211.
kvalo: add space between struct name and *
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This cleans up the connect event parsing by defining a union in
struct wmi_connect_event to match with the three possible sets of
fields that the target uses depending on which type of connect
event is being indicated. In addition, two AP cases are now
separated from ath6kl_connect_event() so that correct field names
can be used to make it actually possible to understand what the
code is doing.
The bug hiding in the previous mess was in parsing the AID incorrectly
when processing the new station connecting event in AP mode. The fix
here for that is also fixing TIM updates for PS buffering to use the
correct AID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a 2-octet reserved field between the flag and aid fields. Fix
that to make the target actually behave as requested.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware initiates roaming only after it reaches a rssi of 20.
This lower rssi threshold can be modified through a wmi command
to modify the roaming behavior.
kvalo: rename debugfs functions and move comment about rssi units next to
ath6kl_wmi_set_roam_lrssi_cmd()
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware sends binary logs with WMIX_DBGLOG_EVENTID event. Create
a buffer which stores the latest logs and which can be copied from
fwlog debugfs file with cp command.
To save memory firmware log support is enabled only when CONFIG_ATH6KL_DEBUG
is enabled.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use WMI_TX_STATUS_EVENTID event to generate cfg80211_mgmt_tx_frame()
calls. Since we support only a single pending frame for now, use the
hardcoded cookie value 1 and store a copy of the pending frame in
the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The target is not ready to accept addkey commands until the connect
event has been delivered, so delay these operations for the initial GTK.
In addition, properly set interface connected and mark netdev ready when
the AP mode setup has been completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use cfg80211 add/del_beacon callbacks for starting/stopping AP mode and
set_beacon to update AP configuration (mainly, to update Beacon and
Probe Response IEs).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
