Currently, this driver can handle only single scatterlist.
Thus, it can't send data beyond FIFO size.
This patch enables this driver can handle multiple scatter list.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
port->flags is of type upf_t, which corresponds to UPF_* flags.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will make it easier to get the driver to support device tree. The
old platform data method is still supported though.
Also change the driver to use only one platform device per port.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is not even used in nios2 arch code anymore.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The three identical uart ports can work either in DMA or PIO mode. Adding such
a module parameter "hsu_dma_enable" will enable user to chose working modes for
each port. If the mfd driver is built in kernel, adding a "mfd.hsu_dma_enable=x"
in kernel command line has the same effect.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In A0 stepping, TX half-empty interrupt is not working, so have to
use the full-empty interrupts whose performance will be 15% lower.
Now re-enable the half-empty interrrupt after it is enabled in
silicon.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only oddities here are a couple of drivers that bogusly called the ldisc
helpers instead of returning -ENOIOCTLCMD. Fix the bug and the rest goes
away.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the regshift member of struct uart_port to store the address stride
from platform data. This way we can save one dereference per call of
altera_uart_readl and altera_uart_writel.
This also allows us to use the driver without platform data, which is
needed for device tree support in the Nios2 port.
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6b5756f176 introduced the
possibility for pdev->id being -1 but the change was not done equally in
altera_uart_remove. This patch fixes this.
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enables PPS support in atmel serial driver to make PPS API working.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In 8250.c original ns16550 autoconfig code, we change the divisor latch when
we goto to high speed mode, we're assuming the previous speed is legacy. This
some times is not true.
For example in a system with both CONFIG_SERIAL_8250 and
CONFIG_SERIAL_8250_PNP set, in this case, the code (autoconfig) will be called
twice, one in serial8250_init/probe() and the other is from
serial_pnp_probe. When serial_pnp_probe calls the autoconfig for NS16550A,
it's already in high speed mode, change the divisor latch (quot << 3) in this
case will make the UART console garbled.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For any reason if the NS16550A was not work in high speed mode (e.g. we hold
NS16550A from going to high speed mode in autoconfig_16550a()), now we are
resume from suspend, we should also set the uartclk to the correct
value. Otherwise it is still the old 1843200 and that will bring issues.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed spi_driver variable to not be h/w specific
set driver name to use DRVNAME define
removed commented-out define
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe routine should call spi_setup() to configure
the SPI bus so it can properly communicate with the device.
E.g. the device operates in SPI mode 1.
Called spi_setup to configure SPI mode, max_speed_hz, and bpw
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platforms containing the 6260 can run up to 25Mhz.
For these platforms set max_speed_hz to 25Mhz.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver should support 32bit SPI transfers. The boolean variable
only allowed 8/16.
Changed to support 8/16/32 for future enabling
of 32 bpw.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a SPI protocol driver and has no DMA ops
associated with the device so the call will fail. Furthermore,
the DMA allocation made here will be used by the SPI
controller driver (parent dev) so it makes sense to
pass that device instead.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port ops must be set AFTER calling port init as that function
zeroes the structure
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCH_DMA is not always enabled when a user uses PCH_UART.
Since overhead of DMA is not small, in case of low frequent
communication, without DMA is better.
Thus, "select PCH_DMA" and DMADEVICES are unnecessary
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support ML7213 device of OKI SEMICONDUCTOR.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some platforms, we need to restore the console speed on resume even
it was not suspended (no_console_suspend), and on others we don't have
to do that.
So don't care about the "console_suspend_enabled" and unconditionally
reset the console speed if it is a console.
This is actually a redo of ba15ab0 (Set proper console speed on resume
if console suspend is disabled) from Deepak Saxena. I also tried to
investigate more to find out if this change will break others, here is
what I've found out:
commit 891b9dd107
Author: Jason Wang <jason77.wang@gmail.com>
serial-core: restore termios settings when resume console ports
commit ca2e71aa8c
Author: Jason Wang <jason77.wang@gmail.com>
serial-core: skip call set_termios/console_start when no_console_suspend
commit 4547be7809
Author: Stanislav Brabec <sbrabec@suse.cz>
serial-core: resume serial hardware with no_console_suspend
commit ba15ab0e8d
Author: Deepak Saxena <dsaxena@laptop.org>
Set proper console speed on resume if console suspend is disabled
from ba15ab0, we learned that, even if the console suspend is disabled
(when no_console_suspend is set), we may still need to "reset the port
to the state it was in before we suspended."
Then with 4547be7, this piece of code is removed.
And then Jason Wang added that back in ca2e71a and 891b9dd, to fix
some breakage on OMAP3EVM platform. From ca2e71a we learned that the
"set_termios" things is actually needed by both console is suspended
and not suspended.
That's why I removed the console_suspended_enabled condition, and only
call console_start() when we actually suspeneded it.
I also noticed in this thread:
http://marc.info/?t=129079257100004&r=1&w=2, which talked about on
some platforms, UART HW will be cut power whether or not we set
no_console_suspend, and then on resume it does not work quite well. I
have a similar HW, and this patch fixed this issue, don't know if this
patch also works on their platforms.
[Update: Stanislav tested this patch on Zaurus and reported it improves the
situation. Thanks.]
CC: Greg KH <greg@kroah.com>
CC: Deepak Saxena <dsaxena@laptop.org>
CC: Jason Wang <jason77.wang@gmail.com>
CC: Stanislav Brabec <sbrabec@suse.cz>
CC: Daniel Drake <dsd@laptop.org>
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is used to store the spi_device ->modalias so they have to be the same
size. SPI_NAME_SIZE is 32.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP can do also dynamic idling so wake-up enable register should be set
also while system is running. If UART_OMAP_WER is not set, then for instance
the RX activity cannot wake up the UART port that is sleeping.
This RX wake-up feature was working when the 8250 driver was used instead
of omap-serial. Reason for this is that the 8250 doesn't set the
UART_OMAP_WER and then arch/arm/mach-omap2/pm34xx.c ends up saving and
restoring the reset default which is the same than value
OMAP_UART_WER_MOD_WKUP here.
Fix this by moving the conditional UART_OMAP_WER write from serial_omap_pm
into serial_omap_startup where wake-up bits are set unconditionally.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Magic SysRq key is not working for OMAP on new serial
console ttyOx because SUPPORT_SYSRQ is not defined
for omap-serial.
This patch defines SUPPORT_SYSRQ in omap-serial and
enables handling of Magic SysRq character.
Further there is an issue of losing first break character.
Removing the reset of the lsr_break_flag fixes this issue.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Manjunath G Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some platform attributes (e.g. max_hz, use_dma) were being intuited
from the modem type. These things should be specified by the platform
data.
Added max_hz, use_dma to ifx_modem_platform_data definition,
replaced is_6160 w/ modem_type, and changed clients accordingly
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is kind of a revert for commit 669b7a0938 "hsu: add a periodic
timer to check dma rx channel", which is a workaround for a bug in A0
stepping silicon, where a dma rx data timeout is missing for some case.
Since new silicon has fixed it and the old version is phasing out, no
need to carry on it any more.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sport->port.irq is unsigned, check for <0 doesn't make sense.
Explicitly cast it to int to check for error.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unbreak Billionton CF bluetooth card. This actually fixes a regression
on zaurus.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: update MAINTAINERS file due to driver movement
tty: move drivers/serial/ to drivers/tty/serial/
tty: move hvc drivers to drivers/tty/hvc/
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
