Variable 'len' is set to conn_info->max_pkt_payload_len but this
value is never read as it is overwritten with a new value later on,
hence it is a redundant assignment and can be removed.
Clean up the following clang-analyzer warning:
net/nfc/nci/hci.c:164:3: warning: Value stored to 'len' is never read
[clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
variable 'status' is unneeded and it's noneed to check the
return value of function vxge_reset_all_vpaths,so declare
it as void.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support get_pauseparam and set_pauseparam of ethtool_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function 'qlcnic_82xx_hw_write_wx_2M' is declared twice, so remove the
repeated declaration.
Cc: Shahed Shaikh <shshaikh@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the refactoring introduced in commit 87614b931c ("net: enetc:
create a common enetc_pf_to_port helper"), enetc_pf_to_port was coded up
to return -1 in case the passed PCIe device does not have a recognized
BDF.
Make sure the -1 value is checked by the callers, to appease static
checkers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_msg(netconsole.c:836) calls netpoll_send_udp after a call to
spin_lock_irqsave, which normally disables interrupts; but in PREEMPT_RT
this call just locks an rt_mutex without disabling irqs. In this case,
netpoll_send_udp is called with interrupts enabled.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadym Kochan says:
====================
Marvell Prestera Switchdev initial updates for firmware version 3.0
This series adds minimal support for firmware version 3.0 which
has such changes like:
- initial routing support
- LAG support
- events interrupt handling changes
Changes just make able to work with new firmware version but
supported features in driver will be added later.
New firmware version was recently merged into linux-firmware tree.
Added ability of loading previous fw major version if the latest one
is missing, also add support for previous FW ABI.
PATCH -> RFC:
1) Load previous fw version if the latest one is missing (suggested by Andrew Lunn)
2) Add support for previous FW ABI version (suggested by Andrew Lunn)
RFC v2:
1) Get rid of automatic decrementing of
major version but hard code it.
2) Print error message with file path if
previous FW could not be loaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets try to load previous fw version in case the latest one is missing on
existing system.
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware version has some ABI and feature changes like:
- LAG support
- initial L3 support
- changed events handling logic
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW IPC flood message format was changed to configure uc/mc
flooding separately, so change code according to this.
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are change in firmware which requires that receiver will
disable event interrupts before handling them and enable them
after finish with handling. Events still may come into the queue
but without receiver interruption.
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for may_sleep to fix the W=1 warnings:
drivers/net/ethernet/neterion/s2io.c:1110: warning: Function parameter or member 'may_sleep' not described in 'init_tti'
drivers/net/ethernet/neterion/s2io.c:3335: warning: Function parameter or member 'may_sleep' not described in 'wait_for_cmd_complete'
drivers/net/ethernet/neterion/s2io.c:4881: warning: Function parameter or member 'may_sleep' not described in 's2io_set_multicast'
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs support for vlan configuraion. create a single file
"vlan_config" for it, and query it by command "cat vlan_config",
return the result to userspace.
The new display style is below:
$ cat vlan_config
I_PORT_VLAN_FILTER: on
E_PORT_VLAN_FILTER: off
FUNC_ID I_VF_VLAN_FILTER E_VF_VLAN_FILTER PORT_VLAN_FILTER_BYPASS
pf off on off
vf0 off on off
FUNC_ID PVID ACCEPT_TAG1 ACCEPT_TAG2 ACCEPT_UNTAG1 ACCEPT_UNTAG2
pf 0 on on on on
vf0 0 on on on on
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, there is hardware limitation for VF to modify
the VLAN filter state, and the VLAN filter state is default
enabled. Now the limitation has been removed in some device,
so add capability flag to check whether the device supports
modify VLAN filter state. If flag on, user will be able to
modify the VLAN filter state by ethtool -K.
VF needs to send mailbox to request the PF to modify the VLAN
filter state for it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are some features of VF depend on PF, so it's necessary
for VF to know whether PF supports. For compatibility, modify
the mailbox HCLGE_MBX_GET_TCINFO, extend its function, use to
get the basic information of PF, including mailbox api version
and PF capabilities.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, with hardware limitation, the port VLAN filter are
effective for both PF and its VFs simultaneously, so a single
function is not able to enable/disable separately, and the VLAN
filter state is default enabled. Now some device supports each
function to bypass port VLAN filter, then each function can
switch VLAN filter separately. Add capability flag to check
whether the device supports modify VLAN filter state. If flag
on, user will be able to modify the VLAN filter state by ethtool
-K.
Furtherly, the default VLAN filter state is also changed
according to whether non-zero VLAN used. Then the device can
receive packet with any VLAN tag if only VLAN 0 used.
The function hclge_need_enable_vport_vlan_filter() is used to
help implement above changes. And the VLAN filter handle for
promisc mode can also be simplified by this function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The struct hclge_vf_vlan_cfg is firstly designed for setting
VLAN filter tag. And it's reused for enable RX VLAN offload
later. It's strange to use member "is_kill" to indicate "enable".
So redefine the struct hclge_vf_vlan_cfg to adapt it.
For there are already 3 subcodes being used in function
hclge_set_vf_vlan_cfg(), use "switch-case" style for each
branch, rather than "if-else". Also simplify the assignment for
each branch to make it more clearly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the PF have called hclge_update_port_base_vlan_cfg() already
before notify VF, it's unnecessary to update port based VLAN again
when received mailbox request from VF.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use struct "hclge_vlan_info" instead of separately parameters
for function hclge_push_vf_port_base_vlan_info(), to make it
more concise.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, option "qos" is igored by HNS3 driver for command
"ip link set ethx vf <vf id> vlan <vlan id> qos <qos value>".
Add support for it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Part 2 of SJA1105 DSA driver preparation for new switch introduction (SJA1110)
This series is a continuation of:
https://patchwork.kernel.org/project/netdevbpf/cover/20210524131421.1030789-1-olteanv@gmail.com/
even though it isn't the first time these patches are submitted (they
were part of the group previously called "Add NXP SJA1110 support to the
sja1105 DSA driver"):
https://patchwork.kernel.org/project/netdevbpf/cover/20210526135535.2515123-1-vladimir.oltean@nxp.com/
but I broke that up again since these patches are already reviewed, for
the most part. There are no changes compared to v2 and v1.
This series of patches contains:
- an adaptation of the driver to the new "ethernet-ports" OF node name
- an adaptation of the driver to support more than 1 SGMII port
- a generalization of the supported phy_interface_t values per port
- an adaptation to encode SPEED_10, SPEED_100, SPEED_1000 into the
hardware registers differently depending on switch revision
- a consolidation of the PHY interface type used for RGMII and another
one for the API exposed for sja1105_dynamic_config_read()
====================
Link: https://lore.kernel.org/r/20210530225939.772553-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SJA1105 has a static configuration comprised of a number of tables
with entries. Some of these can be read and modified at runtime as well,
through the dynamic configuration interface.
As a careful reader can notice from the comments in this file, the
software interface for accessing a table entry through the dynamic
reconfiguration is a bit of a no man's land, and varies wildly across
switch generations and even from one kind of table to another.
I have tried my best to come up with a software representation of a
'common denominator' SPI command to access a table entry through the
dynamic configuration interface:
struct sja1105_dyn_cmd {
bool search;
u64 valid; /* must be set to 1 */
u64 rdwrset; /* 0 to read, 1 to write */
u64 errors;
u64 valident; /* 0 if entry is invalid, 1 if valid */
u64 index;
};
Relevant to this patch is the VALIDENT bit, which for READ commands is
populated by the switch and lets us know if we're looking at junk or at
a real table entry.
In SJA1105, the dynamic reconfiguration interface for management routes
has notably not implemented the VALIDENT bit, leading to a workaround to
ignore this field in sja1105_dynamic_config_read(), as it will be set to
zero, but the data is valid nonetheless.
In SJA1110, this pattern has sadly been abused to death, and while there
are many more tables which can be read back over the dynamic config
interface compared to SJA1105, their handling isn't in any way more
uniform. Generally speaking, if there is a single possible entry in a
given table, and loading that table in the static config is mandatory as
per the documentation, then the VALIDENT bit is deemed as redundant and
more than likely not implemented.
So it is time to make the workaround more official, and add a bit to the
flags implemented by dynamic config tables. It will be used by more
tables when SJA1110 support arrives.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In SJA1105, the xMII Mode Parameters Table field called PHY_MAC denotes
the 'role' of the port, be it a PHY or a MAC. This makes a difference in
the MII and RMII protocols, but RGMII is symmetric, so either PHY or MAC
settings result in the same hardware behavior.
The SJA1110 is different, and the RGMII ports only work when configured
in MAC mode, so keep the port roles in MAC mode unconditionally.
Why we had an RGMII port in the PHY role in the first place was because
we wanted to have a way in the driver to denote whether RGMII delays
should be applied based on the phy-mode property or not. This is already
done in sja1105_parse_rgmii_delays() based on an intermediary
struct sja1105_dt_port (which contains the port role). So it is a
logical fallacy to use the hardware configuration as a scratchpad for
driver data, it isn't necessary.
We can also remove the gating condition for applying RGMII delays only
for ports in the PHY role. The .setup_rgmii_delay() method looks at
the priv->rgmii_rx_delay[port] and priv->rgmii_tx_delay[port] properties
which are already populated properly (in the case of a port in the MAC
role they are false). Removing this condition generates a few more SPI
writes for these ports (clearing the RGMII delays) which are perhaps
useless for SJA1105P/Q/R/S, where we know that the delays are disabled
by default. But for SJA1110, the firmware on the embedded microcontroller
might have done something funny, so it's always a good idea to clear the
RGMII delays if that's what Linux expects.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support the new speed of 2500Mbps, the SJA1110 has achieved
the great performance of changing the encoding in the MAC Configuration
Table for the port speeds of 10, 100, 1000 compared to SJA1105.
Because this is a common driver, we need a layer of indirection in order
to program the hardware with the right values irrespective of switch
generation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the SJA1105, all ports support the parallel "xMII" protocols (MII,
RMII, RGMII) except for port 4 on SJA1105R/S which supports only SGMII.
This was relatively easy to model, by special-casing the SGMII port.
On the SJA1110, certain ports can be pinmuxed between SGMII and xMII, or
between SGMII and an internal 100base-TX PHY. This creates problems,
because the driver's assumption so far was that if a port supports
SGMII, it uses SGMII.
We allow the device tree to tell us how the port pinmuxing is done, and
check that against a PHY interface type compatibility matrix for
plausibility.
The other big change is that instead of doing SGMII configuration based
on what the port supports, we do it based on what is the configured
phy_mode of the port.
The 2500base-x support added in this patch is not complete.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we've succeeded in operating without keeping a copy of the
phy-mode in the driver, since we already have the static config and we
can look at the xMII Mode Parameters Table which already holds that
information.
But with the SJA1110, we cannot make the distinction between sgmii and
2500base-x, because to the hardware's static config, it's all SGMII.
So add a phy_mode property per port inside struct sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looking at the SGMII PCS from SJA1110, which is accessed indirectly
through a different base address as can be seen in the next patch, it
appears odd that the address accessed through indirection still
references the base address from the SJA1105S register map (first MDIO
register is at 0x1f0000), when it could index the SGMII registers
starting from zero.
Except that the 0x1f0000 is not a base address at all, it seems. It is
0x1f << 16 | 0x0000, and 0x1f is coding for the vendor-specific MMD2.
So, it turns out, the Synopsys PCS implements all its registers inside
the vendor-specific MMDs 1 and 2 (0x1e and 0x1f). This explains why the
PCS has no overlaps (for the other MMDs) with other register regions of
the switch (because no other MMDs are implemented).
Change the code to remove the SGMII "base address" and explicitly encode
the MMD for reads/writes. This will become necessary for SJA1110 support.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SJA1105 R and S switches have 1 SGMII port (port 4). Because there
is only one such port, there is no "port" parameter in the configuration
code for the SGMII PCS.
However, the SJA1110 can have up to 4 SGMII ports, each with its own
SGMII register map. So we need to generalize the logic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f2f3e09396be ("net: dsa: sja1105: be compatible with
"ethernet-ports" OF node name"), DSA supports the "ethernet-ports" name
for the container node of the ports, but the sja1105 driver doesn't,
because it handles some device tree parsing of its own.
Add the second node name as a fallback.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alignment should match open parenthesis.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Networking block comments don't use an empty /* line,
use /* Comment...
Block comments use * on subsequent lines.
Block comments use a trailing */ on a separate line.
This patch fixes the comments style issues.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the chackpatch.pl, switch and case should be
at the same indent.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Should not initialise statics to false.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add spaces required around that '='.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the checkpatch error as open brace '{' following struct should
go on the same line.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the checkpatch error as "(foo*)" should be "(foo *)".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch removes some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a complement to commit aa6dd211e4 ("inet: use bigger hash
table for IP ID generation"), but focusing on some specific aspects
of IPv6.
Contary to IPv4, IPv6 only uses packet IDs with fragments, and with a
minimum MTU of 1280, it's much less easy to force a remote peer to
produce many fragments to explore its ID sequence. In addition packet
IDs are 32-bit in IPv6, which further complicates their analysis. On
the other hand, it is often easier to choose among plenty of possible
source addresses and partially work around the bigger hash table the
commit above permits, which leaves IPv6 partially exposed to some
possibilities of remote analysis at the risk of weakening some
protocols like DNS if some IDs can be predicted with a good enough
probability.
Given the wide range of permitted IDs, the risk of collision is extremely
low so there's no need to rely on the positive increment algorithm that
is shared with the IPv4 code via ip_idents_reserve(). We have a fast
PRNG, so let's simply call prandom_u32() and be done with it.
Performance measurements at 10 Gbps couldn't show any difference with
the previous code, even when using a single core, because due to the
large fragments, we're limited to only ~930 kpps at 10 Gbps and the cost
of the random generation is completely offset by other operations and by
the network transfer time. In addition, this change removes the need to
update a shared entry in the idents table so it may even end up being
slightly faster on large scale systems where this matters.
The risk of at least one collision here is about 1/80 million among
10 IDs, 1/850k among 100 IDs, and still only 1/8.5k among 1000 IDs,
which remains very low compared to IPv4 where all IDs are reused
every 4 to 80ms on a 10 Gbps flow depending on packet sizes.
Reported-by: Amit Klein <aksecurity@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210529110746.6796-1-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds validation for used length (might come
from an untrusted device) to avoid data corruption
or loss.
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20210531135852.113-1-xieyongji@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
