The "gsmi" driver bridges userland with firmware specific routines for
accessing hardware.
Currently, this driver only supports NVRAM and eventlog information.
Deprecated functions have been removed from the driver, though their
op-codes are left in place so that they are not re-used.
This driver works by trampolining into the firmware via the smi_command
outlined in the FADT table. Three protocols are used due to various
limitations over time, but all are included herein.
This driver should only ever load on Google boards, identified by either
a "Google, Inc." board vendor string in DMI, or "GOOGLE" in the OEM
strings of the FADT ACPI table. This logic happens in
gsmi_system_valid().
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Aaron Durbin <adurbin@google.com>
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
st_drv uses skb*() interfaces, so it should depend on NET.
It also uses GPIO interfaces, so it should depend on GPIOLIB.
st_kim.c uses syss_*() calls, so it should #include
<linux/sysfs.h>.
Fixes these observed build errors:
ERROR: "skb_queue_purge" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_pull" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_queue_tail" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "__alloc_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "kfree_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_dequeue" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_put" [drivers/misc/ti-st/st_drv.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the line longer than 80 of memory_uevent function .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before commit
b402843 (Driver core: move dev_get/set_drvdata to drivers/base/dd.c)
calling dev_set_drvdata with dev=NULL was an unchecked error. After some
discussion about what to return in this case removing the check (and so
producing a null pointer exception) seems fine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the res = NULL case more consistant to the res != NULL case
as now both overwrite pdev->resource.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the data = NULL case more consistent to the data != NULL case.
The functional change is that now
platform_device_add_data(somepdev, NULL, somesize)
sets pdev->dev.platform_data to NULL instead of not touching it.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device is registered to a bus it will be a) added to the list
of devices of the bus and b) bind to a driver (if one matches). As a
result of a driver being registered at this bus between a) and b) this
device could already be bound to a driver. This leads to a warning
and incorrect refcounting.
To fix this add a check to device_attach to identify an already bound
device.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rfkill is no longer used by Texas Instruments shared transport driver to
communicate with user-space.
This patch removes the dependency of rfkill to be enabled to build
shared transport driver in the Kconfig.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When certain technologies shutdown their interface without waiting for
the acknowledgement from the chip. The receive_buf from the TTY would be
invoked a while after the relevant technology is unregistered.
This patch introduces a new flag "is_registered" which maintains the
state of protocols BT, FM or GPS and thereby removes the need to clear
the protocol data from ST when protocols gets unregistered.
This fixes corner cases when HCI RESET is sent down from bluetooth stack
and the receive_buf is called from tty after 250ms before which
bluetooth would have unregistered from the system.
OR - when FM application decides to close down the device without
sending a power-off FM command resulting in some RDS data or interrupt
data coming in after the driver is unregistered.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
printk: /dev/kmsg - properly support writev() to avoid interleaved printk lines
We should avoid calling printk() in a loop, when we pass a single
string to /dev/kmsg with writev().
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The uioinfo should be cleaned up when uninstall, otherwise re-install
failure of uio_pdrv_genirq.ko will happen.
Signed-off-by: Jie Zhou <b30303@freescale.com>
Signed-off-by: Aisheng Dong <b29396@freescale.com>
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of uio devices that could be used should be less than
UIO_MAX_DEVICES by design, and this work guards any cases in which id
more than UIO_MAX_DEVICES is utilized.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When finding mm index for vma it looks more flexible that the mm could
be sparse, and both the size of mm and the pgoff of vma could give
correct selection.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Hilscher / IBHsoftec netPLC cards to uio_netx userspace IO driver.
Changes from v1 -> v2:
Fixed whitespace errors reported by scripts/checkpatch.pl which were caused by email client.
Signed-off-by: Daniel Trautmann <dtrautmann@ibhsoftec-sps.de>
Signed-off-by: "Hans J. Koch" <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device_type structure does not contain data that changes
during usage and should be const. This allows devices to declare
the struct const.
I have patches to change all the subsystems, but need the infra
structure change first.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should unwind and return an error if register_efivars() fails.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a cut and paste bug. We intended to free ->del_var and
->new_var but we only free ->new_var.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
Mouse gets "stuck" after restore of PV guest but buttons are in working
condition.
If driver has been configured for ABS coordinates at start it will get
XENKBD_TYPE_POS events and then suddenly after restore it'll start getting
XENKBD_TYPE_MOTION events, that will be dropped later and they won't get
into user-space.
Regression was introduced by hunk 5 and 6 of
5ea5254aa0ad269cfbd2875c973ef25ab5b5e9db
("Input: xen-kbdfront - advertise either absolute or relative
coordinates").
Driver on restore should ask xen for request-abs-pointer again if it is
available. So restore parts that did it before 5ea5254.
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[v1: Expanded the commit description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Calculate a default based on the number of ABS axes, REL axes,
and MT slots for the device during input device registration.
Signed-off-by: Jeff Brown <jeffbrown@android.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.
Also remove some plug-related code that is no longer needed.
Signed-off-by: NeilBrown <neilb@suse.de>
In raid5 plugging is used for 2 things:
1/ collecting writes that require a bitmap update
2/ collecting writes in the hope that we can create full
stripes - or at least more-full.
We now release these different sets of stripes when plug_cnt
is zero.
Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
Signed-off-by: NeilBrown <neilb@suse.de>
When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.
If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NeilBrown <neilb@suse.de>
md has some plugging infrastructure for RAID5 to use because the
normal plugging infrastructure required a 'request_queue', and when
called from dm, RAID5 doesn't have one of those available.
This relied on the ->unplug_fn callback which doesn't exist any more.
So remove all of that code, both in md and raid5. Subsequent patches
with restore the plugging functionality.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that unplugging is done differently, the unplug_fn callback is
never called, so it can be completely discarded.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid submits a lot of IO from the various raid threads.
So adding start/finish plug calls to those so that some
plugging happens.
Signed-off-by: NeilBrown <neilb@suse.de>
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36221
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [.38 down to .34]
When warning on the use of deprecated i2c_driver methods
attach_adapter and detach_adapter, mention the name of the driver
which needs to be updated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (43 commits)
Revert "USB: isp1760-hcd: move imask clear after pending work is done"
xHCI: Implement AMD PLL quirk
xhci: Tell USB core both roothubs lost power.
usbcore: Bug fix: system can't suspend with USB3.0 device connected to USB3.0 hub
USB: Fix unplug of device with active streams
USB: xhci - also free streams when resetting devices
xhci: Fix NULL pointer deref in handle_port_status()
USB: xhci - fix math in xhci_get_endpoint_interval()
USB: xhci: simplify logic of skipping missed isoc TDs
USB: xhci - remove excessive 'inline' markings
USB: xhci: unsigned char never equals -1
USB: xhci - fix unsafe macro definitions
USB: fix formatting of SuperSpeed endpoints in /proc/bus/usb/devices
USB: isp1760-hcd: move imask clear after pending work is done
USB: fsl_qe_udc: send ZLP when zero flag and length % maxpacket == 0
usb: qcserial add missing errorpath kfrees
usb: qcserial avoid pointing to freed memory
usb: Fix qcserial memory leak on rmmod
USB: ftdi_sio: add ids for Hameg HO720 and HO730
USB: option: Added support for Samsung GT-B3730/GT-B3710 LTE USB modem.
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6879/1: fix personality test wrt usage of domain handlers
ARM: 6878/1: fix personality flag propagation across an exec
ARM: 6877/1: the ADDR_NO_RANDOMIZE personality flag should be honored with mmap()
ARM: 6876/1: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
ARM: pxa: convert incorrect IRQ_TO_IRQ() to irq_to_gpio()
ARM: mmp: align NR_BUILTIN_GPIO with gpio interrupt number
ARM: pxa: align NR_BUILTIN_GPIO with GPIO interrupt number
ARM: pxa: always clear LPM bits for PXA168 MFPR
pcmcia: limit pxa2xx_trizeps4 subdriver to trizeps4 platform
pcmcia: limit pxa2xx_balloon3 subdriver to balloon3 platform
ARM: pxafb: Fix access to nonexistent member of pxafb_info
ARM: 6872/1: arch:common:Makefile Remove unused config in the Makefile.
ARM: 6868/1: Preserve the VFP state during fork
ARM: 6867/1: Introduce THREAD_NOTIFY_COPY for copy_thread() hooks
ARM: 6866/1: Do not restrict HIGHPTE to !OUTER_CACHE
ARM: 6865/1: perf: ensure pass through zero is counted on overflow
ARM: 6864/1: hw_breakpoint: clear DBGVCR out of reset
ARM: Only allow PM_SLEEP with CPUs which support suspend
ARM: Make consolidated PM sleep code depend on PM_SLEEP
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the wrong members and the wrong function's definition, since the
irq_chip had changed.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the driver aware of the initial status of the regulator.
The leds-regulator driver was ignoring the initial status of the
regulator; this resulted in rdev->use_count being incremented to 2 after
calling regulator_led_set_value() in the .probe method when a regulator
was already enabled at insmod time, which made it impossible to ever
disable the regulator.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 5808544690.
To quote Richard:
I don't think this should be mainlined. It was a
misunderstanding on my part. If you see all the other hdc
drivers in the same location, they all do the same thing (i.e.
clear the interrupt status first, then do the work) that
"glitch" I think I saw was actually two back-to-back
interrupts.
Sebastian (the original author of isp1760) explained it to me a
few days after my submission.
sorry for the confusion
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disable the optional PM feature inside the Hudson3 platform under
the following conditions:
1. If an isochronous device is connected to xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
The PM feature needs to be disabled to eliminate PLL startup delays when the
link comes out of low power state. The performance of DMA data transfer could
be impacted if system delay were encountered and in addition to the PLL start
up delays. Disabling the PM would leave room for unpredictable system delays
in order to guarantee uninterrupted data transfer to isochronous audio or
video stream devices that require time sensitive information. If data in an
audio/video stream was interrupted then erratic audio or video performance
may be encountered.
AMD PLL quirk is already implemented in OHCI/EHCI driver. After moving the
quirk code to pci-quirks.c and export them, xHCI driver can call it directly
without having the quirk implementation in itself.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
On a resume, when the power is lost during hibernate, the USB core will
call hub_reset_resume for the xHCI USB 2.0 roothub, but not for the USB
3.0 roothub:
[ 164.748310] usb usb1: root hub lost power or was reset
[ 164.748353] usb usb2: root hub lost power or was reset
[ 164.748487] usb usb3: root hub lost power or was reset
[ 164.748488] xhci_hcd 0000:01:00.0: Stop HCD
...
[ 164.870039] hub 4-0:1.0: hub_resume
...
[ 164.870054] hub 3-0:1.0: hub_reset_resume
This causes issues later, because the USB core assumes the USB 3.0 hub
attached to the USB 3.0 roothub is still active. It attempts to queue a
control URB for the external hub, which fails because all the device
slot contexts were released when the USB 3.0 roothub lost power:
[ 164.980044] hub 4-1:1.0: hub_resume
[ 164.980047] xhci_hcd 0000:01:00.0: Get port status returned 0x10101
[ 164.980049] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980053] hub 3-0:1.0: port 1: status 0101 change 0001
[ 164.980056] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980060] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc90008948440, 32'h202e1, 4'hf);
[ 164.980062] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980066] xhci_hcd 0000:01:00.0: clear port connect change, actual port 0 status = 0x2e1
[ 164.980069] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980072] xhci_hcd 0000:01:00.0: get port status, actual port 1 status = 0x2a0
[ 164.980074] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980077] xhci_hcd 0000:01:00.0: Get port status returned 0x100
[ 164.980079] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980082] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980085] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980088] hub 4-1:1.0: port 4: status 0000 change 0000
[ 164.980091] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980094] hub 4-1:1.0: activate --> -22
[ 164.980113] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980117] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980119] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980123] hub 4-1:1.0: can't resume port 4, status -22
[ 164.980126] hub 4-1:1.0: port 4 status ffff.ffff after resume, -22
[ 164.980129] usb 4-1.4: can't resume, status -22
[ 164.980131] hub 4-1:1.0: logical disconnect on port 4
This causes issues when a USB 3.0 hard drive is attached to the external
USB 3.0 hub when the system is hibernated:
[ 6249.849653] sd 8:0:0:0: [sdb] Unhandled error code
[ 6249.849659] sd 8:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 6249.849663] sd 8:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 2a 08 00 00 02 00
[ 6249.849671] end_request: I/O error, dev sdb, sector 10760
Make sure to inform the USB core that *both* xHCI roothubs lost power.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch clear PORT_POWER when suspend a USB3.0 device behind a USB3.0
external hub, so the system can suspend and resume.
Note USB3.0 device may not work after system resume and this is a temporary
workaround. The correct fix will be in future patches.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If I unplug a device while the UAS driver is loaded, I get an oops
in usb_free_streams(). This is because usb_unbind_interface() calls
usb_disable_interface() which calls usb_disable_endpoint() which sets
ep_out and ep_in to NULL. Then the UAS driver calls usb_pipe_endpoint()
which returns a NULL pointer and passes an array of NULL pointers to
usb_free_streams().
I think the correct fix for this is to check for the NULL pointer
in usb_free_streams() rather than making the driver check for this
situation. My original patch for this checked for dev->state ==
USB_STATE_NOTATTACHED, but the call to usb_disable_interface() is
conditional, so not all drivers would want this check.
Note from Sarah Sharp: This patch does avoid a potential dereference,
but the real fix (which will be implemented later) is to set the
.soft_unbind flag in the usb_driver structure for the UAS driver, and
all drivers that allocate streams. The driver should free any streams
when it is unbound from the interface. This avoids leaking stream rings
in the xHCI driver when usb_disable_interface() is called.
This should be queued for stable trees back to 2.6.35.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Currently, when resetting a device, xHCI driver disables all but one
endpoints and frees their rings, but leaves alone any streams that
might have been allocated. Later, when users try to free allocated
streams, we oops in xhci_setup_no_streams_ep_input_ctx() because
ep->ring is NULL.
Let's free not only rings but also stream data as well, so that
calling free_streams() on a device that was reset will be safe.
This should be queued for stable trees back to 2.6.35.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
When we get a port status change event, we need to figure out what type of
port it came from: a USB 3.0 port, or a USB 2.0/1.1 port. We can't know
which usb_hcd to use until that point, so hcd will be NULL for part of the
function. Unfortunately, if any of the sanity checks fail, we'll jump to
the cleanup label before hcd is set to a valid pointer, and then we'll
attempt to tell the USB core to kick the hcd, which is NULL.
Skip kicking the roothub if the sanity checks fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
The logic of the handling Missed Service Error Events was pretty
confusing as we were checking the same condition several times.
In addition, it caused compiler warning since the compiler could
not figure out that event_trb is actually unused in case we are
skipping current TD.
Fix that by rearranging "skip" condition checks, and factor out
skip_isoc_td() so that it is called explicitly.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
