- Fix list of valid LS3 currents from mA to µA
- Fix selection of min/max microAmps of LS3.
Selecting one of the configured values as max value now really
selects it instead of the next lower one
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: c90456e36d ("regulator: pv88090: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: 99cf3af5e2 ("regulator: pv88080: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: f307a7e9b7 ("regulator: pv88060: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change buck1 voltage range to be conform with the data-sheet.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.
Found by debugging a broken voltage setup on Orange Pi One Plus.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step values for some of the LDOs appears to be incorrect, resulting
in incorrect voltages (or at least, ones which are different from the
Samsung 3.4 vendor kernel).
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device links are refcounted, device_link_remove() has to be called as
many times as device_link_add().
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With current n_voltages setting, regulator_list_voltage will return
-EINVAL when selector >=57. The highest selector is 0x41, so the
n_voltages should be 0x41+1, i.e. 66.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure unwind all resources if probe fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix copy-paste mistake while converting to use defines for masks.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since c32569e358 ("regulator: Use of_node_name_eq for node name
comparisons"), regulator node name comparisons are case sensitive.
The DA9052 driver uses uppercase, but the DT has lowercase.
Fix this by using a lowercase regulator name to match the DT node name.
Fixes: c32569e358 ("regulator: Use of_node_name_eq for node name comparisons")
Cc: Support Opensource <support.opensource@diasemi.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since c32569e358 ("regulator: Use of_node_name_eq for node name
comparisons") Vivien reported the mc13892-regulator complaining about
not being able to find regulators.
This is because prior to that commit we used of_node_cmp() to compare
the regulator array passed from mc13892_regulators down to
mc13xxx_parse_regulators_dt() and they are all defined in uppercase
letters by the MC13892_*_DEFINE* macros, whereas they are defined as
lowercase in the DTS.
Fix this by using a lowercase regulator name to match the DT node name.
Fixes: c32569e358 ("regulator: Use of_node_name_eq for node name comparisons")
Reported-by: Vivien Didelot <vivien.didelot@gmail.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If regulator DT node doesn't exist, its of_parse_cb callback
function isn't called. Then all values for DT properties are
filled with zero. This leads to wrong register update for
FPS and POK settings.
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Current implementation missed the case BCM590XX_REG_VSR, so
bcm590xx_get_enable_register() returns 0 when id is BCM590XX_REG_VSR.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix trival copy-n-paste mistake.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so,
returns with its error code.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build error when CONFIG_REGMAP_I2C=m && CONFIG_REGULATOR_MCP16502=y.
drivers/regulator/mcp16502.o: In function `mcp16502_probe':
mcp16502.c:(.text+0xca): undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mcp16502_suspend/resume_noirq is only used by SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
when CONFIG_PM_SLEEP is defined.
So use #ifdef CONFIG_PM_SLEEP instead CONFIG_SUSPEND guard.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does the following:
- align parameter with parenthesis
- fix compile error
If CONFIG_SUSPEND is not set the dummy pm_ops
callbacks are named mcp16502_suspend and mcp16502_resume
instead of mcp16502_suspend_noirq and mcp16502_resume_noirq.
Excerpt from compile log (kbuild test robot):
In file included from include/linux/device.h:23:0,
from include/linux/gpio/driver.h:5,
from include/asm-generic/gpio.h:13,
from include/linux/gpio.h:62,
from drivers/regulator/mcp16502.c:11:
>> drivers/regulator/mcp16502.c:527:32: error: 'mcp16502_suspend_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend'?
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
>> drivers/regulator/mcp16502.c:528:10: error: 'mcp16502_resume_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend_noirq'?
mcp16502_resume_noirq)
vim +527 drivers/regulator/mcp16502.c
524
525 #ifdef CONFIG_PM
526 static const struct dev_pm_ops mcp16502_pm_ops = {
> 527 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
> 528 mcp16502_resume_noirq)
529 };
530 #endif
531 static const struct i2c_device_id mcp16502_i2c_id[] = {
532 { "mcp16502", 0 },
533 { }
534 };
535 MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id);
536
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
drivers/regulator/act8945a-regulator.c:340:1: warning:
symbol 'act8945a_pm' was not declared. Should it be static?
Fixes: 7482d6ecc6 ("regulator: act8945a-regulator: Implement PM functionalities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix 'defined but not used' compiler warning for act8945a_suspend()
function in case CONFIG_PM_SLEEP is not defined.
Fixes: b5ebba46e6 ("regulator: act8945a-regulator: add shutdown function")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reported-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of set_ramp_delay feature was missing an assignment which
should have populated slew_rate table for dcdc2 regulator. Add it.
Fixes: d29f54df8b ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for entering/resuming suspend states.
It does this by setting the LPM pin of the PMIC.
When suspending the PMIC will enter the Low-power mode
when the LPM pin will be set to high. If the suspend target state
is suspend-to-mem, the PMIC will transition to Hibernate mode,
otherwise, if it is standby, it will remain in Low-power mode.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement shutdown method to make sure the PMIC will not enter the suspend
state when the system is shutdown.
This work is based on work done by Borris Brezillon on [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix line over 80 chars checkpatch.pl warning.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
fix checkpatch warning, adapt commit message, add LDO modes support,
move modes constants to active-semi,8945a-regulator.h, remove rdevs from
struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlock expert registers for act8945a.
This is based on orginal work of Boris Brezillon at [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the Arizona LDO1 driver becomes
redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the wm8994 driver becomes redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of regulator_resolve_supply() we have historically turned
on our supply in some cases. This could be for one of two reasons:
1. If resolving supplies was happening before the call to
set_machine_constraints() we needed to predict if
set_machine_constraints() was going to turn the regulator on and we
needed to preemptively turn the supply on.
2. Maybe set_machine_constraints() happened before we could resolve
supplies (because we failed the first time to resolve) and thus we
might need to propagate an enable that already happened up to our
supply.
Historically regulator_resolve_supply() used _regulator_is_enabled()
to decide whether to turn on the supply.
Let's change things a little bit. Specifically:
1. Let's try to enable the supply and the regulator in the same place,
both in set_machine_constraints(). This means that we have exactly
the same logic for enabling the supply and the regulator.
2. Let's properly set use_count when we enable always-on or boot-on
regulators even for those that don't have supplies. The previous
commit 1fc12b0589 ("regulator: core: Avoid propagating to
supplies when possible") only did this right for regulators with
supplies.
3. Let's make it clear that the only time we need to enable the supply
in regulator_resolve_supply() is if the main regulator is currently
in use. By using use_count (like the rest of the code) to decide
if we're going to enable our supply we keep everything consistent.
Overall the new scheme should be cleaner and easier to reason about.
In addition to fixing regulator_summary to be more correct (because of
the more correct use_count), this change also has the effect of no
longer using _regulator_is_enabled() in this code path.
_regulator_is_enabled() could return an error code for some regulators
at bootup (like RPMh) that can't read their initial state. While one
can argue that the design of those regulators is sub-optimal, the new
logic sidesteps this brokenness. This fix in particular fixes
observed problems on Qualcomm sdm845 boards which use the
above-mentioned RPMh regulator. Those problems were made worse by
commit 1fc12b0589 ("regulator: core: Avoid propagating to supplies
when possible") because now we'd think at bootup that the SD
regulators were already enabled and we'd never try them again.
Fixes: 1fc12b0589 ("regulator: core: Avoid propagating to supplies when possible")
Reported-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S2MPS11 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the TPS65090 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S5M8767 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the DA9211 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
