All of the ciphers that are tested for are always supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setmac() only copies the mac address it is called with into
common->macaddr, yet in all call sites, the supplied mac address pointer
is already common->macaddr.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Debugfs requires a u32 for bool knobs though so we turn the
ath9k_hw knob into a u32 as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5416 and all newer chipsets use a 32 bit rx timestamp, so there
is no need to keep the 15 bit timestamp extending logic around.
This patch removes ath9k_hw_extend_tsf (replaced by a call to
ath9k_hw_gettsf64), and reduces the frequency of TSF reads, which
can improve performance in some cases.
This change also has the side effect of making rx timestamps
more accurate.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ANI implementation will use this to skip ANI
calibration upon a scan. This cannot be ported to the
older ANI implementation unless default ANI values from
the ANI are also used upon a scan. This is essentially
what one of the things thenew ANI does.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family will use a slightly modified ANI
implementation which has not yet been tested on the other hardware
families. To allow for this new ANI implementation a few ANI
calls need to be abstracted away. This patch just allows for
each hardware family to declare their own ANI ops and annotates
the current ANI implementation as old.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used by the ANI code next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Async fifo is now enabled only for versions 1.3 and above.
Enable it in the appropriate place, in the reset routine,
instead of process_ini().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The baseband watchdog will monitor blocks of the baseband
through timers and will issue an interrupt when things are
detected to be stalled. It is only available on the AR9003
family.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new AR9003 EEPROM code does tune the card for the configured
tx power level, we need to fill in the correct power limits in the TPC
part of the DMA descriptor.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast clock operation (44Mhz) is enabled for 5Ghz in ar9003, so
take care of the conversion from usec to hw clock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable TX IQ calibration, it was prematurely enabled in
previous versions.
Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a function to clean up tx status ring.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reset tx status ring suring chip reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also move interrupt related code to mac.c
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 TX/RX gain is currently initialized with the other
components, so for now AR9003 does not implment this callback,
after hardware bring up we can test moving the TX/RX gain there
as well and if it works well move them to its own callback as
well.
Since all INI stuff is now moved out hw.c no longer needs to
include and touch any original INI headers/structs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is specific to the AR9002 family only.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move out the generic hardware family code out into their own
files, we have one for AR5008, AR9001, and AR9002 family (ar9002_hw.c)
and another file for the new AR9003 hardware family (ar9003_hw.c).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.
Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c
This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can reorganize the code in such a way that eep_map can be removed,
which makes the code more clearer.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store appropriate desc length which will be used by the
ath9k module while duplicating tx desc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family now initializes hardware by block
components and into stages: pre, core and init.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set rx buf size in register 0x60
* Set rxdp on the respective hw rx queue (HP and LP queues)
* Process rx descriptor
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HP & LP queue depth and rx status length.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 supports extended DMA (EDMA), this comes with some
bells and whistles on top of the legacy DMA that we are used
to. Mark AR9003 and later chips EDMA capable.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
