Its perfectly valid to assign a nvmet port to listen on "any"
IP address (traddr 0.0.0.0 for ipv4 address family) for IP based
transport ports. However, we must not return this address in
discovery log entries. Instead we need to return the address
where the request was accepted on (req->port address).
Since this is nvme transport specific, introduce an optional
.disc_traddr interface that is designed to check that a
port in question is bound to "any" IP address and if so, set
the traddr from the port where the request came from.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe fixes from Keith for 4.16-rc.
* 'for-jens' of git://git.infradead.org/nvme:
nvmet: fix PSDT field check in command format
nvme-multipath: fix sysfs dangerously created links
nvme-pci: Fix nvme queue cleanup if IRQ setup fails
nvmet-loop: use blk_rq_payload_bytes for sgl selection
nvme-rdma: use blk_rq_payload_bytes instead of blk_rq_bytes
nvme-fabrics: don't check for non-NULL module in nvmf_register_transport
PSDT field section according to NVM_Express-1.3:
"This field specifies whether PRPs or SGLs are used for any data
transfer associated with the command. PRPs shall be used for all
Admin commands for NVMe over PCIe. SGLs shall be used for all Admin
and I/O commands for NVMe over Fabrics. This field shall be set to
01b for NVMe over Fabrics 1.0 implementations.
Suggested-by: Idan Burstein <idanb@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
blk_rq_bytes does the wrong thing for special payloads like discards and
might cause the driver to not set up a SGL.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Execute discard command on block device that doesn't support it
should return success.
Returning internal error while using multi-path fails the path.
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
nvmet_req_init looked up a namespace and took a reference on it (unless it
failed prior to that). If the request is uninitialized (in error cases) we
need to remove that reference in case it was taken, otherwise we leak
namespace reference when calling nvme_req_uninit.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make it symmetric to nvmet_alloc_ctrl().
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove the allocated id on error.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe transport driver module unload may (and usually does) trigger
iteration over the active controllers and delete them all (sometimes
under a mutex). However, a controller can be created concurrently with
module unload which can lead to leakage of resources (most important char
device node leakage) in case the controller creation occured after the
unload delete and drain sequence. To protect against this, we take a
module reference to guarantee that the nvme transport driver is not
unloaded while creating a controller.
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The current fc transport add_port routine validates that there is a
matching port to the target port config. It then takes a reference
on the targetport. The del_port removes the reference.
Unfortunately, if the LLDD undergoes a hw reset or driver unload and
wants to unreg the targetport, due to the reference, the targetport
effectively can't be removed. It requires the admin to remove the
port from the nvmet config first, which calls the del_port.
Note: it appears nvmetcli clear skips over the del_port call (I'm
not attempting to change that).
There's no real reason to take the reference. With FC, there is nothing
to enable or disable as the presence of the FC targetport implicitly
means its enabled, and removal of the targtport means its disabled.
Change add_port to simply validate and change remove_port to a noop.
No references are taken on the targetport.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The split between what the host accesses on its flows vs what the
target side accesses was flawed. Abort handling didn't properly
clear initiator vs target structure cross-reference and locks
weren't used for synchronization. Thus, there were issues of
freeing structures too soon and access after free.
A couple of these existed pre the IN_ISR mods, but when the
target upcalls were converted to work items, thus adding delays
between the 2 sides of accesses, the problems became pronounced.
Resolve by:
- tracking io state mainly in the tgt-side io structure.
- make the tgt-side io structure released by reference not by
code flow.
- when changing initiator structures, use locks for
synchronization
- aborts are clearly tracked for which side saw the abort, and
after seeing the abort, cross-references are cleared under lock.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The existing fcloop driver expects the target side upcalls to
the transport to context switch, thus the calls into the nvmet layer
are not done in the calling context of the host/initiator down calls.
The xxx_IN_ISR feature flags are used to select this logic.
The xxx_IN_ISR feature flags should go away in the nvmet_fc transport
as no other lldd utilizes them. Both Broadcom and Cavium lldds have their
own non-ISR deferred handlers thus the nvmet calls can be made directly.
This patch converts the paths that make the target upcalls (command
receive, abort receive) such that they schedule a work item rather
than expecting the transport to schedule the work item.
The patch also cleans up the following:
- The completion path from target to host scheduled a host work
element called "work". Rename it "tio_done_work" for code clarity.
- The abort io path called a iniwork item to call the host side
io done. This is no longer needed as the abort routine can make
the same call.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The current fcloop driver gets its lport structure from the private
area co-allocated with the fc_localport. All is fine except the
teardown path, which wants to wait on the completion, which is marked
complete by the delete_localport callback performed after
unregister_localport. The issue is, the nvme_fc transport frees the
localport structure immediately after delete_localport is called,
meaning the original routine is trying to wait on a complete that
was just freed.
Change such that a lport struct is allocated coincident with the
addition and registration of a localport. The private area of the
localport now contains just a backpointer to the real lport struct.
Now, the completion can be waited for, and after completing, the
new structure can be kfree'd.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A test case revealed a race condition of an i/o completing on a thread
parallel to the delete_association generating the aborts for the
outstanding ios on the controller. The i/o completion was freeing the
target fcloop context, thus the abort task referenced the just-freed
memory.
Correct by clearing the target/initiator cross pointers in the io
completion and abort tasks before calling the callbacks. On aborts
that detect already finished io's, ensure the complete context is
called.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is a bit chatty to report on each queue, log it only for debug
purposes.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is a bit chatty to report on every deleted queue, so keep it for debug
purposes only.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We already do that when we are notified in device removal
which is triggered when unregistering as an ib client.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the sgl_alloc() and sgl_free() functions instead of open coding
these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the sgl_alloc() and sgl_free() functions instead of open coding
these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kbuild test robot send mail of a potential use of an uninitialized
variable - "tport" in fcloop_delete_targetport() which then calls
__targetport_unreg() which uses the variable. It will never be the
case it is uninitialized as the call to __targetport_unreg() only
occurs if there is a valid nport pointer. And at the time the nport
pointer is assigned, the tport variable is set.
Remove the warning by assigning a NULL value initially.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Whenever a cmd is received a reference is taken while looking up the
queue. The reference is removed after the cmd is done as the iod is
returned for reuse. The fod may be reused for a deferred (recevied but
no job context) cmd. Existing code removes the reference only if the
fod is not reused for another command. Given the fod may be used for
one or more ios, although a reference was taken per io, it won't be
matched on the frees.
Remove the reference on every fod free. This pairs the references to
each io.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In case the queue is not LIVE (fully functional and connected at the nvmf
level), we cannot allow any commands other than connect to pass through.
Add a new queue state flag NVME_LOOP_Q_LIVE which is set after nvmf connect
and cleared in queue teardown.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reorganize nvmet_fc_handle_fcp_rqst() so that the nvmet req.transfer_len
field is set after the call nvmet_req_init(). An update to nvmet now
has nvmet_req_init() clearing the field, thus the fc transport was losing
the value.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAloLSTALHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYNxfhAAv3cunxiEPEAvs+1xuGd3cZYaxz7qinvIODPxIKoF
kRWiuy5PUklRMnJ8seOgJ1p1QokX6Sk4cZ8HcctDJVByqODjOq4K5eaKVN1ZqJoz
BUzO/gOqfs64r9yaFIlKfe8nFA+gpUftSeWyv3lThxAIJ1iSbue7OZ/A10tTOS1m
RWp9FPepFv+nJMfWqeQU64BsoDQ4kgZ2NcEA+jFxNx5dlmIbLD49tk0lfddvZQXr
j5WyAH73iugilLtNUGVOqSzHBY4kUvfCKUV7leirCegyMoGhFtA87m6Wzwbo6ZUI
DwQLzWvuPaGv1P2PpNEHfKiNbfIEp75DRyyyf87DD3lc5ffAxQSm28mGuwcr7Rn5
Ow/yWL6ERMzCLExoCzEkXYJISy7T5LIzYDgNggKMpeWxysAduF7Onx7KfW1bTuhK
mHvY7iOXCjEvaIVaF8uMKE6zvuY1vCMRXaJ+kC9jcIE3gwhg+2hmQvrdJ2uAFXY+
rkeF2Poj/JlblPU4IKWAjiPUbzB7Lv0gkypCB2pD4riaYIN5qCAgF8ULIGQp2hsO
lYW1EEgp5FBop85oSO/HAGWeH9dFg0WaV7WqNRVv0AGXhKjgy+bVd7iYPpvs7mGw
z9IqSQDORcG2ETLcFhZgiJpCk/itwqXBD+wgMOjJPP8lL+4kZ8FcuhtY9kc9WlJE
Tew=
=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
Much easier to just opencode this helper. Also use ARRAY_SIZE instead of
passing the inline bvec array size manually.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@rimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently the NVMe target stores the expexted data length in req->data_len
and uses that for data transfer decisions, but that does not take the
actual transfer length in the SGLs into account. So this adds a new
transfer_len field, into which the transport drivers store the actual
transfer length. We then check the two match before actually executing
the command.
The FC transport driver already had such a field, which is removed in
favour of the common one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The driver can handle tracking only one AEN request, so this patch
removes handling for multiple ones.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All the transports were unnecessarilly duplicating the AEN request
accounting. This patch defines everything in one place.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
the status is either success or some status id and
we don't need a local variable for it.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We already allocated the buffer with kzalloc.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
small typos fixed in admin-cmd.c
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A NULL deref happens when nvmet_rdma_remove_one() is called more than once
(e.g. while connected via 2 ports).
The first call frees the queues related to the first ib_device but
doesn't remove them from the queue list.
While calling nvmet_rdma_remove_one() for the second ib_device it goes over
the full queue list again and we get the NULL deref.
Fixes: f1d4ef7d ("nvmet-rdma: register ib_client to not deadlock in device removal")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grmberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
That we we can also poll non blk-mq queues. Mostly needed for
the NVMe multipath code, but could also be useful elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below is a stack trace for an issue that was reported.
What's happening is that the nvmet layer had it's controller kato
timeout fire, which causes it to schedule its fatal error handler
via the fatal_err_work element. The error handler is invoked, which
calls the transport delete_ctrl() entry point, and as the transport
tears down the controller, nvmet_sq_destroy ends up doing the final
put on the ctlr causing it to enter its free routine. The ctlr free
routine does a cancel_work_sync() on fatal_err_work element, which
then does a flush_work and wait_for_completion. But, as the wait is
in the context of the work element being flushed, its in a catch-22
and the thread hangs.
[ 326.903131] nvmet: ctrl 1 keep-alive timer (15 seconds) expired!
[ 326.909832] nvmet: ctrl 1 fatal error occurred!
[ 327.643100] lpfc 0000:04:00.0: 0:6313 NVMET Defer ctx release xri
x114 flg x2
[ 494.582064] INFO: task kworker/0:2:243 blocked for more than 120
seconds.
[ 494.589638] Not tainted 4.14.0-rc1.James+ #1
[ 494.594986] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
disables this message.
[ 494.603718] kworker/0:2 D 0 243 2 0x80000000
[ 494.609839] Workqueue: events nvmet_fatal_error_handler [nvmet]
[ 494.616447] Call Trace:
[ 494.619177] __schedule+0x28d/0x890
[ 494.623070] schedule+0x36/0x80
[ 494.626571] schedule_timeout+0x1dd/0x300
[ 494.631044] ? dequeue_task_fair+0x592/0x840
[ 494.635810] ? pick_next_task_fair+0x23b/0x5c0
[ 494.640756] wait_for_completion+0x121/0x180
[ 494.645521] ? wake_up_q+0x80/0x80
[ 494.649315] flush_work+0x11d/0x1a0
[ 494.653206] ? wake_up_worker+0x30/0x30
[ 494.657484] __cancel_work_timer+0x10b/0x190
[ 494.662249] cancel_work_sync+0x10/0x20
[ 494.666525] nvmet_ctrl_put+0xa3/0x100 [nvmet]
[ 494.671482] nvmet_sq_:q+0x64/0xd0 [nvmet]
[ 494.676540] nvmet_fc_delete_target_queue+0x202/0x220 [nvmet_fc]
[ 494.683245] nvmet_fc_delete_target_assoc+0x6d/0xc0 [nvmet_fc]
[ 494.689743] nvmet_fc_delete_ctrl+0x137/0x1a0 [nvmet_fc]
[ 494.695673] nvmet_fatal_error_handler+0x30/0x40 [nvmet]
[ 494.701589] process_one_work+0x149/0x360
[ 494.706064] worker_thread+0x4d/0x3c0
[ 494.710148] kthread+0x109/0x140
[ 494.713751] ? rescuer_thread+0x380/0x380
[ 494.718214] ? kthread_park+0x60/0x60
Correct by having the fc transport convert to a different workq context
for the actual controller teardown which may call the cancel_work_sync.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
No change in behavior except that the FC code cancels two work items a
little later now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the ->delete_work and the associated helpers to common code instead
of duplicating them in every driver. This also adds the missing reference
get/put for the loop driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of allocating a separate struct device for the character device
handle embedd it into struct nvme_ctrl and use it for the main controller
refcounting. This removes double refcounting and gets us an automatic
reference for the character device operations. We keep ctrl->device as a
pointer for now to avoid chaning printks all over, but in the future we
could look into message printing helpers that take a controller structure
similar to what other subsystems do.
Note the delete_ctrl operation always already has a reference (either
through sysfs due this change, or because every open file on the
/dev/nvme-fabrics node has a refernece) when it is entered now, so we
don't need to do the unless_zero variant there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
In case we disable namespaces which has the nsid like
subsystem max_nsid we need to search for the next largest nsid
in this subsystem. If the subsystem don't has more namespaces
we set it to 0, else we take nsid from the last namespace in
namespaces list because the list is sorted while inserting.
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: slight refactor]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make config_item_type structures const as they are either passed to a
function having the argument as const or used inside an if statement or
stored in the const "ci_type" field of a config_item structure.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This flag is useful for admin queues that aren't used for normal IO.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In testing target io in read write mix, we did indeed get into cases where
sqhd didn't update properly and slowly missed enough updates to shutdown
the queue.
Protect the updating sqhd by using cmpxchg, and for that turn the sqhd
field into a u32 so that cmpxchg works on it for all architectures.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Raise the max number of IO queues to 128. There are several hosts with
more than 64 cpus/threads.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that there are potentially long delays between when a remoteport or
targetport delete calls is made and when the callback occurs (dev_loss_tmo
timeout), no longer block in the delete routines and move the final nport
puts to the callbacks.
Moved the fcloop_nport_get/put/free routines to avoid forward declarations.
Ensure port_info structs used in registrations are nulled in case fields
are not set (ex: devloss_tmo values).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When searching for queue id's ensure they are within the expected range.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Avoid calling the put routine, as it may traverse to free routines while
holding the target lock.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
