The ixgbe_ptp.c file sometimes uses hw_cc as the local variable for the
cycle counter in ixgbe_ptp_read_X550. However, we use just 'cc' as
a local variable for this by convention else where in the file.
Convert this lone usage of 'hw_cc' into just the shorter 'cc' name to
match the other read functions in the file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ixgbe_ptp_setup_sdp_X540 attempts to program a software
defined pin, in order to generate a pulse-per-second output on SDP 0.
It does work to generate the output, but does not align the output on
the full second. Additionally, it does not take into account the
cyclecounter multiplier. This leads to somewhat confusing code which is
likely to be incorrect if blindly copied to another hardware type.
Update this code to account for the cyclecounter multiplier, and to
directly use timecounter_read.
This change ensures that the SDP output will align properly on a full
second, and makes the intent of the calculations a bit more clear.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we waited for a whole 15 seconds before we cleared the Tx
timestamp state. This is astronomically long compared to the worst case
timings expected by our devices. In addition, this is longer than the
wait in ptp4l when it detects a fault (caused by missing Tx timestamps).
Thus, reduce the timer to only 1 second, which is well after the maximum
expected delay. This should reduce user frustration when a timestamp
does get dropped for some reason.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The total_packets count at ixgbe_clean_xdp_tx_irq is
always zero when testing with xdpsock -t -N. Set the gso_segs
to 1 to make the tx packet count correct.
Signed-off-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The tx bytecount is done twice. When running
'./xdpsock -t -N -i eth3' and 'ip -s link show dev eth3'
The avg packet size is 120 instead of 60. So remove the
extra one.
Signed-off-by: William Tu <u9012063@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As current implementation of netdev already contains and provides
umems for us, we no longer have the need to contain these
structures in ixgbe_adapter.
Refactor the code to operate on netdev-provided umems.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Here, we add a bitmap to the ixgbe_adapter that tracks if a
certain queue pair has been "zero-copy enabled" via the ndo_bpf.
The bitmap is used in ixgbe_xsk_umem, and enables zero-copy if
and only if XDP is enabled, the corresponding qid in the bitmap
is set, and the umem is non-NULL;
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----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=KySr
-----END PGP SIGNATURE-----
Merge tag 'pidfd-fixes-v5.2-rc4' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux
Pull pidfd fixes from Christian Brauner:
"The contains two small patches to the pidfd samples and test binaries
respectively.
They were lacking appropriate ifdefines for __NR_pidfd_send_signal and
could hence lead to compilation errors when that was not defined.
This was spotted on mips independently by Guenter Roeck (who was kind
enough to send a fix for the samples binary) and Arnd who spotted it
in linux-next.
Apart from these two patches, there's also a patch to update the
comments for the pidfd_send_signal() syscall which were slightly
wrong/inconsistenly worded"
* tag 'pidfd-fixes-v5.2-rc4' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
tests: fix pidfd-test compilation
signal: improve comments
samples: fix pidfd-metadata compilation
- Avoid NULL deref when unloading/reloading ramoops module (Pi-Hsun Shih)
- Run ramoops without crash dump region
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=g26W
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fixes from Kees Cook:
- Avoid NULL deref when unloading/reloading ramoops module (Pi-Hsun
Shih)
- Run ramoops without crash dump region
* tag 'pstore-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/ram: Run without kernel crash dump region
pstore: Set tfm to NULL on free_buf_for_compression
dev_err() is more appropriate for printing error messages inside
drivers, so switch to dev_err().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-06-05
one more shot... now with patch 2 fixed up so that it uses the
dst entry returned from dst_check().
From the v1 cover letter:
Please apply the following set of qeth fixes to -net.
- The first two patches fix issues in the L3 driver's cast type
selection for transmitted skbs.
- Alexandra adds a sanity check when retrieving VLAN information from
neighbour address events.
- The last patch adds some missing error handling for qeth's new
multiqueue code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_tx_queues() can return an error, deal with it.
Fixes: 73dc2daf11 ("s390/qeth: add TX multiqueue support for OSA devices")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling sysfs attribute bridge_hostnotify triggers a series of udev events
for the MAC addresses of all currently connected peers. In case no VLAN is
set for a peer, the device reports the corresponding MAC addresses with
VLAN ID 4096. This currently results in attribute VLAN=4096 for all
non-VLAN interfaces in the initial series of events after host-notify is
enabled.
Instead, no VLAN attribute should be reported in the udev event for
non-VLAN interfaces.
Only the initial events face this issue. For dynamic changes that are
reported later, the device uses a validity flag.
This also changes the code so that it now sets the VLAN attribute for
MAC addresses with VID 0. On Linux, no qeth interface will ever be
registered with VID 0: Linux kernel registers VID 0 on all network
interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0.
Peers with other OSs could register MACs with VID 0.
Fixes: 9f48b9db9a ("qeth: bridgeport support - address notifications")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While qeth_l3 uses netif_keep_dst() to hold onto the dst, a skb's dst
may still have been obsoleted (via dst_dev_put()) by the time that we
end up using it. The dst then points to the loopback interface, which
means the neighbour lookup in qeth_l3_get_cast_type() determines a bogus
cast type of RTN_BROADCAST.
For IQD interfaces this causes us to place such skbs on the wrong
HW queue, resulting in TX errors.
Fix-up the various call sites to first validate the dst entry with
dst_check(), and fall back accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When selecting the cast type of a neighbourless IPv4 skb (eg. on a raw
socket), qeth_l3 falls back to the packet's destination IP address.
For this case we should classify traffic sent to 255.255.255.255 as
broadcast.
This fixes DHCP requests, which were misclassified as unicast
(and for IQD interfaces thus ended up on the wrong HW queue).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: factor out firmware handling
Let's factor out firmware handling into a separate source code file.
This simplifies reading the code and makes clearer what the interface
between driver and firmware handling is.
v2:
- fix small whitespace issue in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's factor out firmware handling into a separate source code file.
This simplifies reading the code and makes clearer what the interface
between driver and firmware handling is.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out firmware handling rename r8169.c to
r8169_main.c.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build errors in Mediatek mtk_eth_soc driver.
It looks like these 3 source files were meant to be linked together
since 2 of them are library-like functions,
but they are currently being built as 3 loadable modules.
Fixes these build errors:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/mediatek/mtk_eth_path.o
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/mediatek/mtk_sgmii.o
ERROR: "mtk_sgmii_init" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_setup_hw_path" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_sgmii_setup_mode_force" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_sgmii_setup_mode_an" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_w32" [drivers/net/ethernet/mediatek/mtk_eth_path.ko] undefined!
ERROR: "mtk_r32" [drivers/net/ethernet/mediatek/mtk_eth_path.ko] undefined!
This changes the loadable module name from mtk_eth_soc to mtk_eth.
I didn't see a way to leave it as mtk_eth_soc.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define __NR_pidfd_send_signal if it isn't to prevent a potential
compilation error.
To make pidfd-test compile on all arches, irrespective of whether
or not syscall numbers are assigned, define the syscall number to -1.
If it isn't defined this will cause the kernel to return -ENOSYS.
Fixes: 575a0ae974 ("selftests: add tests for pidfd_send_signal()")
Signed-off-by: Christian Brauner <christian@brauner.io>
Improve the comments for pidfd_send_signal().
First, the comment still referred to a file descriptor for a process as a
"task file descriptor" which stems from way back at the beginning of the
discussion. Replace this with "pidfd" for consistency.
Second, the wording for the explanation of the arguments to the syscall
was a bit inconsistent, e.g. some used the past tense some used present
tense. Make the wording more consistent.
Signed-off-by: Christian Brauner <christian@brauner.io>
Define __NR_pidfd_send_signal if it isn't to prevent a compilation error.
To make pidfd-metadata compile on all arches, irrespective of whether
or not syscall numbers are assigned, define the syscall number to -1.
If it isn't defined this will cause the kernel to return -ENOSYS.
Fixes: 43c6afee48 ("samples: show race-free pidfd metadata access")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Christian Brauner <christian@brauner.io>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[christian@brauner.io: tweak commit message]
Signed-off-by: Christian Brauner <christian@brauner.io>
If CONFIG_FUNCTION_GRAPH_TRACER is enabled function
arch_counter_get_cntvct() is marked as notrace. However, function
__arch_counter_get_cntvct is marked as inline. If
CONFIG_OPTIMIZE_INLINING is set that will make the two functions
tracable which they shouldn't.
Rework so that functions __arch_counter_get_* are marked with
__always_inline so they will be inlined even if CONFIG_OPTIMIZE_INLINING
is turned on.
Fixes: 0ea415390c ("clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
asm/smp.h is included by linux/smp.h and some drivers, in particular
irqchip drivers can access cpu_logical_map[] in order to perform SMP
affinity tasks. Make arm64 consistent with other architectures here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In commit 06a916feca ("arm64: Expose SVE2 features for
userspace"), new hwcaps are added that are detected via fields in
the SVE-specific ID register ID_AA64ZFR0_EL1.
In order to check compatibility of secondary cpus with the hwcaps
established at boot, the cpufeatures code uses
__read_sysreg_by_encoding() to read this ID register based on the
sys_reg field of the arm64_elf_hwcaps[] table.
This leads to a kernel splat if an hwcap uses an ID register that
__read_sysreg_by_encoding() doesn't explicitly handle, as now
happens when exercising cpu hotplug on an SVE2-capable platform.
So fix it by adding the required case in there.
Fixes: 06a916feca ("arm64: Expose SVE2 features for userspace")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As Eric noted, the current wrapper for ptype func hook inside
__netif_receive_skb_list_ptype() has no chance of avoiding the indirect
call: we enter such code path only for protocols other than ipv4 and
ipv6.
Instead we can wrap the list_func invocation.
v1 -> v2:
- use the correct fix tag
Fixes: f5737cbadb ("net: use indirect calls helpers for ptype hook")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes says:
====================
net: dsa: mv88e6xxx: support for mv88e6250
This adds support for the mv88e6250 chip. Initially based on the
mv88e6240, this time around, I've been through each ->ops callback and
checked that it makes sense, either replacing with a 6250 specific
variant or dropping it if no equivalent functionality seems to exist
for the 6250. Along the way, I found a few oddities in the existing
code, mostly sent as separate patches/questions.
The one relevant to the 6250 is the ieee_pri_map callback, where the
existing mv88e6085_g1_ieee_pri_map() is actually wrong for many of the
existing users. I've put the mv88e6250_g1_ieee_pri_map() patch first
in case some of the existing chips get switched over to use that and
it is deemed important enough for -stable.
v4:
- fix style issue in 1/10
- add Andrew's reviewed-by to 1,6,7,8,9,10.
v3:
- rebase on top of net-next/master
- add reviewed-bys to patches unchanged from v2 (2,3,4,5)
- add 6250-specific ->ieee_pri_map, ->port_set_speed, ->port_link_state (1,6,7)
- in addition, use mv88e6065_phylink_validate for ->phylink_validate,
and don't implement ->port_get_cmode, ->port_set_jumbo_size,
->port_disable_learn_limit, ->rmu_disable
- drop ptp support
- add patch adding the compatible string to the DT binding (9)
- add small refactoring patch (10)
v2:
- rebase on top of net-next/master
- add reviewed-by to two patches unchanged from v1 (2,3)
- add separate watchdog_ops
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mv88e6250_g1_reset() is identical to mv88e6352_g1_reset() except
for the call of mv88e6352_g1_wait_ppu_polling(), so refactor the 6352
version in term of the 6250 one. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6250 has port_base_addr 0x8 or 0x18 (depending on
configuration pins), so it constitutes a new family and hence needs
its own compatible string.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell 88E6250. I've checked that each
member in the ops-structure makes sense, and basic switchdev
functionality works fine.
It uses the new dual_chip option, and since its port registers start
at SMI address 0x08 or 0x18 (i.e., always sw_addr + 0x08), we need to
introduce a new compatible string in order for the auto-identification
in mv88e6xxx_detect() to work.
The chip has four per port 16-bits statistics registers, two of which
correspond to the existing "sw_in_filtered" and "sw_out_filtered" (but
at offsets 0x13 and 0x10 rather than 0x12 and 0x13, because why should
this be easy...). Wiring up those four statistics seems to require
introducing a STATS_TYPE_PORT_6250 bit or similar, which seems a tad
ugly, so for now this just allows access to the STATS_TYPE_BANK0 ones.
The chip does have ptp support, and the existing
mv88e6352_{gpio,avb,ptp}_ops at first glance seem like they would work
out-of-the-box, but for simplicity (and lack of testing) I'm eliding
this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6250 has a rather different way of reporting the link, speed
and duplex status. A simple difference is that the link bit is bit 12
rather than bit 11 of the port status register.
It gets more complicated for speed and duplex, which do not have
separate fields. Instead, there's a four-bit PortMode field, and
decoding that depends on whether it's a phy or mii port. For the phy
ports, only four of the 16 values have defined meaning; the rest are
called "reserved", so returning {SPEED,DUPLEX}_UNKNOWN seems
reasonable.
For the mii ports, most possible values are documented (0x3 and 0x5
are reserved), but I'm unable to make sense of them all. Since the
bits simply reflect the Px_MODE[3:0] configuration pins, just support
the subset that I'm certain about. Support for other setups can be
added later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data sheet also mentions the possibility of selecting 200 Mbps for
the MII ports (ports 5 and 6) by setting the ForceSpd field to
0x2 (aka MV88E6065_PORT_MAC_CTL_SPEED_200). However, there's a note
that "actual speed is determined by bit 8 above", and flipping back a
page, one finds that bits 13:8 are reserved...
So without further information on what bit 8 means, let's stick to
supporting just 10 and 100 Mbps on all ports.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6352_G2_WDOG_CTL_* bits almost, but not quite, describe the
watchdog control register on the mv88e6250. Among those actually
referenced in the code, only QC_ENABLE differs (bit 6 rather than bit
5).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are almost identical to the 6185 variants, but have fewer bits
for the FID.
Bit 10 of the VTU_OP register (offset 0x05) is the VidPolicy bit,
which one should probably preserve in mv88e6xxx_g1_vtu_op(), instead
of always writing a 0. However, on the 6352 family, that bit is
located at bit 12 in the VTU FID register (offset 0x02), and is always
unconditionally cleared by the mv88e6xxx_g1_vtu_fid_write()
function.
Since nothing in the existing driver seems to know or care about that
bit, it seems reasonable to not add the boilerplate to preserve it for
the 6250 (which would require adding a chip-specific vtu_op function,
or adding chip-quirks to the existing one).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the currently supported chips have .num_databases either 256 or
4096, so this patch does not change behaviour for any of those. The
mv88e6250, however, has .num_databases == 64, and it does not put the
upper two bits in ATU control 13:12, but rather in ATU Operation
9:8. So change the logic to prepare for supporting mv88e6250.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e6250 (as well as 6220, 6071, 6070, 6020) do not support
multi-chip (indirect) addressing. However, one can still have two of
them on the same mdio bus, since the device only uses 16 of the 32
possible addresses, either addresses 0x00-0x0F or 0x10-0x1F depending
on the ADDR4 pin at reset [since ADDR4 is internally pulled high, the
latter is the default].
In order to prepare for supporting the 88e6250 and friends, introduce
mv88e6xxx_info::dual_chip to allow having a non-zero sw_addr while
still using direct addressing.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite a few of the existing supported chips that use
mv88e6085_g1_ieee_pri_map as ->ieee_pri_map (including, incidentally,
mv88e6085 itself) actually have a reset value of 0xfa50 in the
G1_IEEE_PRI register.
The data sheet for the mv88e6095, however, does describe a reset value
of 0xfa41.
So rather than changing the value in the existing callback, introduce
a new variant with the 0xfa50 value. That will be used by the upcoming
mv88e6250, and existing chips can be switched over one by one,
preferably double-checking both the data sheet and actual hardware in
each case - if anybody actually feels this is important enough to
care.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when rx csum is disabled, vmxnet3 driver does not turn
off lro, which can cause performance issues if user does not turn off
lro explicitly. This patch adds fix_features support which is used to
turn off LRO whenever RXCSUM is disabled.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Rishi Mehta <rmehta@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's some NICs, such as hinic, with NETIF_F_IP_CSUM and NETIF_F_TSO
on but NETIF_F_HW_CSUM off. And ipvlan device features will be
NETIF_F_TSO on with NETIF_F_IP_CSUM and NETIF_F_IP_CSUM both off as
IPVLAN_FEATURES only care about NETIF_F_HW_CSUM. So TSO will be
disabled in netdev_fix_features.
For example:
Features for enp129s0f0:
rx-checksumming: on
tx-checksumming: on
tx-checksum-ipv4: on
tx-checksum-ip-generic: off [fixed]
tx-checksum-ipv6: on
Fixes: a188222b6e ("net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: add struct nexthop to fib{6}_info
Set 10 of 11 to improve route scalability via support for nexthops as
standalone objects for fib entries.
https://lwn.net/Articles/763950/
This sets adds 'struct nexthop' to fib_info and fib6_info. IPv4
already handles multiple fib_nh entries in a single fib_info, so
the conversion to use a nexthop struct is fairly mechanical. IPv6
using a nexthop struct with a fib6_info impacts a lot of core logic
which is built around the assumption of a single, builtin fib6_nh
per fib6_info. To make this easier to review, this set adds
nexthop to fib6_info and adds checks in most places fib6_info is
used. The next set finishes the IPv6 conversion, walking through
the places that need to consider all fib6_nh within a nexthop struct.
Offload drivers - mlx5, mlxsw and rocker - are changed to fail FIB
entries using nexthop objects. That limitation can be removed once
the drivers are updated to properly support separate nexthops.
This set starts by adding accessors for fib_nh and fib_nhs in a
fib_info. This makes it easier to extract the number of nexthops
in the fib entry and a specific fib_nh once the entry references
a struct nexthop. Patch 2 converts more of IPv4 code to use
fib_nh_common allowing a struct nexthop to use a fib6_nh with an
IPv4 entry.
Patches 3 and 4 add 'struct nexthop' to fib{6}_info and update
references to both take a different path when it is set. New
exported functions are added to the nexthop code to validate a
nexthop struct when configured for use with a fib entry. IPv4
is allowed to use a nexthop with either v4 or v6 entries. IPv6
is limited to v6 entries only. In both cases list_heads track
the fib entries using a nexthop struct for fast correlation on
events (e.g., device events or nexthop events like delete or
replace).
The last 3 patches add hooks to drivers listening for FIB
notificationas. All 3 of them reject the routes as unsupported,
returning an error message to the user via extack. For mlxsw
at least this is a stop gap measure until the driver is updated for
proper support.
Functional tests for nexthops have already been committed. Those tests
will be active after the next patch set which makes the code paths
created by this set and the next one live.
Existing code paths moved to the else branch of 'if (f{6}i->nh)' checks
are covered by existing tests under selftests/net.
v3
- remove ip6_create_rt_rcu from ip6_pol_route in patch 4 and use pcpu
routes for REJECT routes with the blackhole nexthop (request from Wei)
v2
- no code changes from v1
- commit messages for first 4 patches updated
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct nexthop and nh_list list_head to fib6_info. nh_list is the
fib6_info side of the nexthop <-> fib_info relationship. Since a fib6_info
referencing a nexthop object can not have 'sibling' entries (the old way
of doing multipath routes), the nh_list is a union with fib6_siblings.
Add f6i_list list_head to 'struct nexthop' to track fib6_info entries
using a nexthop instance. Update __remove_nexthop_fib to walk f6_list
and delete fib entries using the nexthop.
Add a few nexthop helpers for use when a nexthop is added to fib6_info:
- nexthop_fib6_nh - return first fib6_nh in a nexthop object
- fib6_info_nh_dev moved to nexthop.h and updated to use nexthop_fib6_nh
if the fib6_info references a nexthop object
- nexthop_path_fib6_result - similar to ipv4, select a path within a
multipath nexthop object. If the nexthop is a blackhole, set
fib6_result type to RTN_BLACKHOLE, and set the REJECT flag
Update the fib6_info references to check for nh and take a different path
as needed:
- rt6_qualify_for_ecmp - if a fib entry uses a nexthop object it can NOT
be coalesced with other fib entries into a multipath route
- rt6_duplicate_nexthop - use nexthop_cmp if either fib6_info references
a nexthop
- addrconf (host routes), RA's and info entries (anything configured via
ndisc) does not use nexthop objects
- fib6_info_destroy_rcu - put reference to nexthop object
- fib6_purge_rt - drop fib6_info from f6i_list
- fib6_select_path - update to use the new nexthop_path_fib6_result when
fib entry uses a nexthop object
- rt6_device_match - update to catch use of nexthop object as a blackhole
and set fib6_type and flags.
- ip6_route_info_create - don't add space for fib6_nh if fib entry is
going to reference a nexthop object, take a reference to nexthop object,
disallow use of source routing
- rt6_nlmsg_size - add space for RTA_NH_ID
- add rt6_fill_node_nexthop to add nexthop data on a dump
As with ipv4, most of the changes push existing code into the else branch
of whether the fib entry uses a nexthop object.
Update the nexthop code to walk f6i_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'struct nexthop' and nh_list list_head to fib_info. nh_list is the
fib_info side of the nexthop <-> fib_info relationship.
Add fi_list list_head to 'struct nexthop' to track fib_info entries
using a nexthop instance. Add __remove_nexthop_fib and add it to
__remove_nexthop to walk the new list_head and mark those fib entries
as dead when the nexthop is deleted.
Add a few nexthop helpers for use when a nexthop is added to fib_info:
- nexthop_cmp to determine if 2 nexthops are the same
- nexthop_path_fib_result to select a path for a multipath
'struct nexthop'
- nexthop_fib_nhc to select a specific fib_nh_common within a
multipath 'struct nexthop'
Update existing fib_info_nhc to use nexthop_fib_nhc if a fib_info uses
a 'struct nexthop', and mark fib_info_nh as only used for the non-nexthop
case.
Update the fib_info functions to check for fi->nh and take a different
path as needed:
- free_fib_info_rcu - put the nexthop object reference
- fib_release_info - remove the fib_info from the nexthop's fi_list
- nh_comp - use nexthop_cmp when either fib_info references a nexthop
object
- fib_info_hashfn - use the nexthop id for the hashing vs the oif of
each fib_nh in a fib_info
- fib_nlmsg_size - add space for the RTA_NH_ID attribute
- fib_create_info - verify nexthop reference can be taken, verify
nexthop spec is valid for fib entry, and add fib_info to fi_list for
a nexthop
- fib_select_multipath - use the new nexthop_path_fib_result to select a
path when nexthop objects are used
- fib_table_lookup - if the 'struct nexthop' is a blackhole nexthop, treat
it the same as a fib entry using 'blackhole'
The bulk of the changes are in fib_semantics.c and most of that is
moving the existing change_nexthops into an else branch.
Update the nexthop code to walk fi_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert more IPv4 code to use fib_nh_common over fib_nh to enable routes
to use a fib6_nh based nexthop. In the end, only code not using a
nexthop object in a fib_info should directly access fib_nh in a fib_info
without checking the famiy and going through fib_nh_common. Those
functions will be marked when it is not directly evident.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helpers to access fib_nh and fib_nhs fields of a fib_info. Drop the
fib_dev macro which is an alias for the first nexthop. Replacements:
fi->fib_dev --> fib_info_nh(fi, 0)->fib_nh_dev
fi->fib_nh --> fib_info_nh(fi, 0)
fi->fib_nh[i] --> fib_info_nh(fi, i)
fi->fib_nhs --> fib_info_num_path(fi)
where fib_info_nh(fi, i) returns fi->fib_nh[nhsel] and fib_info_num_path
returns fi->fib_nhs.
Move the existing fib_info_nhc to nexthop.h and define the new ones
there. A later patch adds a check if a fib_info uses a nexthop object,
and defining the helpers in nexthop.h avoid circular header
dependencies.
After this all remaining open coded references to fi->fib_nhs and
fi->fib_nh are in:
- fib_create_info and helpers used to lookup an existing fib_info
entry, and
- the netdev event functions fib_sync_down_dev and fib_sync_up.
The latter two will not be reused for nexthops, and the fib_create_info
will be updated to handle a nexthop in a fib_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, packets received in another VRF should not be passed to an
unbound socket in the default VRF. This patch updates the IPv4 UDP
multicast logic to match the unicast VRF logic (in compute_score()),
as well as the IPv6 mcast logic (in __udp_v6_is_mcast_sock()).
The particular case I noticed was DHCP discover packets going
to the 255.255.255.255 address, which are handled by
__udp4_lib_mcast_deliver(). The previous code meant that running
multiple different DHCP server or relay agent instances across VRFs
did not work correctly - any server/relay agent in the default VRF
received DHCP discover packets for all other VRFs.
Fixes: 6da5b0f027 ("net: ensure unbound datagram socket to be chosen when not in a VRF")
Signed-off-by: Tim Beale <timbeale@catalyst.net.nz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit had an unintended side effect with reject routes:
rt6i_pcpu is expected to always be initialized for all fib6_info except
the null entry. The commit mentioned below skips it for reject routes
and ends up leaking references to the loopback device. For example,
ip netns add foo
ip -netns foo li set lo up
ip -netns foo -6 ro add blackhole 2001:db8:1::1
ip netns exec foo ping6 2001:db8:1::1
ip netns del foo
ends up spewing:
unregister_netdevice: waiting for lo to become free. Usage count = 3
The fib_nh_common_init is not needed for reject routes (no ipv4 caching
or encaps), so move the alloc_percpu_gfp after it and adjust the goto label.
Fixes: f40b6ae2b6 ("ipv6: Move pcpu cached routes to fib6_nh")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds LRO support for the HiNIC driver.
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
