We already maintain an array of VLANs used by the switch so we can
simply iterate over it to report the occupancy via devlink.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering our slave MDIO bus outside of the OF infrastructure is
necessary in order to avoid creating double references of the same
Device Tree nodes, however it is not sufficient to guarantee that the
MDIO bus diversion is used because of_phy_connect() will still resolve
to a valid PHY phandle and it will connect to the PHY using its parent
MDIO bus which is still the SF2 master MDIO bus. The reason for that is
because BCM7445 systems were already shipped with a Device Tree blob
looking like this (irrelevant parts omitted for simplicity):
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
phy-mode = "rgmii-txid";
phy-handle = <&phy0>;
reg = <1>;
label = "rgmii_1";
};
...
mdio@403c0 {
...
phy0: ethernet-phy@0 {
broken-turn-around;
device_type = "ethernet-phy";
max-speed = <0x3e8>;
reg = <0>;
compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
};
};
There is a hardware issue with chip revisions (Dx) that lead to the
development of the following commits:
461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
536fab5bf5 ("net: dsa: bcm_sf2: Do not register slave MDIO bus with OF")
b8c6cd1d31 ("net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0")
There should have been an internal MDIO bus node created for the chip
revision (Dx) that suffers from this problem, but it did not happen back
then.
Had that happen, that we should have correctly parented phy@0 (bcm53125
below) as child node of the internal MDIO bus, but the production Device
Tree blob that was shipped with the firmware targeted the fixed version
of the chip, despite both the affected and corrected chips being shipped
into production.
The problem is that of_phy_connect() for port@1 will happily resolve the
'phy-handle' from the mdio@403c0 node, which bypasses the diversion
completely. This results in this double programming that the diversion
refers to and aims to avoid. In order to force of_phy_connect() to fail,
and have DSA call to dsa_slave_phy_connect(), we must deactivate
ethernet-phy@0 from mdio@403c0, and the best way to do that is by
removing the phandle property completely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever a port gets enabled/disabled, recalcultate the required switch
clock rate to make sure it always gets set to the expected rate
targeting our switch use case. This is only done for the BCM7445 switch
as there is no clocking profile available for BCM7278.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetch the corresponding clock resource and enable/disable it during
suspend/resume if and only if we have no ports defined for Wake-on-LAN.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 only appears to support pause modes on RGMII interfaces (the
enable bits are in the RGMII control register.) Setup the pause modes
for RGMII connections.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the bcm_sf2 to use the finalised speed and duplex in its
mac_link_up() call rather than the parameters in mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->link has never been valid in mac_config() implementations -
while it may be correct in some calls, it is not true that it can be
relied upon.
Fix bcm_sf2 to use the correct method of handling forced link status.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were registering our slave MDIO bus with OF and doing so with
assigning the newly created slave_mii_bus of_node to the master MDIO bus
controller node. This is a bad thing to do for a number of reasons:
- we are completely lying about the slave MII bus is arranged and yet we
still want to control which MDIO devices it probes. It was attempted
before to play tricks with the bus_mask to perform that:
https://www.spinics.net/lists/netdev/msg429420.html but the approach
was rightfully rejected
- the device_node reference counting is messed up and we are effectively
doing a double probe on the devices we already probed using the
master, this messes up all resources reference counts (such as clocks)
The proper fix for this as indicated by David in his reply to the
thread above is to use a platform data style registration so as to
control exactly which devices we probe:
https://www.spinics.net/lists/netdev/msg430083.html
By using mdiobus_register(), our slave_mii_bus->phy_mask value is used
as intended, and all the PHY addresses that must be redirected towards
our slave MDIO bus is happening while other addresses get redirected
towards the master MDIO bus.
Fixes: 461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to enable learning for the ASP port since it only receives
directed traffic, this allows us to bypass ARL-driven forwarding rules
which could conflict with Broadcom tags and/or CFP forwarding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes: de34d7084e ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7458bd540f ("net: dsa:
bcm_sf2: Also configure Port 5 for 2Gb/sec on 7278") as it causes
advanced congestion buffering issues with 7278 switch devices when using
their internal Giabit PHY. While this is being debugged, continue with
conservative defaults that work and do not cause packet loss.
Fixes: 7458bd540f ("net: dsa: bcm_sf2: Also configure Port 5 for 2Gb/sec on 7278")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Either port 5 or port 8 can be used on a 7278 device, make sure that
port 5 also gets configured properly for 2Gb/sec in that case.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab an optional and exclusive reset controller line for the switch and
manage it during probe/remove functions accordingly. For 7278 devices we
change bcm_sf2_sw_rst() to use the reset controller line since the
WATCHDOG_CTRL register does not reset the switch contrary to stated
documentation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it became possible for the DSA core to use a CPU port different
than 8, our bcm_sf2_imp_setup() function was broken because it assumes
that registers are applicable to port 8. In particular, the port's MAC
is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS
bits if we are not configured for port 8.
Fixes: 9f91484f6f ("net: dsa: make "label" property optional for dsa2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leverage the recently add b53_mdb_{add,del,prepare} functions since they
work as-is for bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The SF2 binding does not specify that the CPU port should have
properties mandatory for successfully instantiating a PHYLINK object. As
such, there will be missing properties (including fixed-link) and when
attempting to validate and later configure link modes, we will have an
incorrect set of parameters (interface, speed, duplex).
Simply prevent the CPU port from being configured through PHYLINK since
bcm_sf2_imp_setup() takes care of that already.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.
Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, we use a dev_info() print which already
displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume in the bcm_sf2 driver that the DSA master network device
supports ethtool_ops::{get,set}_wol operations, which is not a given.
Avoid de-referencing potentially non-existent function pointers and
check them as we should.
Fixes: 96e65d7f3f ("net: dsa: bcm_sf2: add support for Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS. The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions. The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return CFP policer statistics (Green, Yellow or Red) as part of the
standard ethtool statistics. This helps debug when CFP rules may not be
hit (0 counter).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding CFP statistics, we will need to overlay the
standard B53 statistics, so create specific bcm_sf2_sw_* functions to
call into their b53_common.c counterpart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need a dedicated statistics mutex since we leverage
b53_common for statistics now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
