When adding ar6004 SDIO support I forgot to add corresponding
MODULE_FIRMWARE() definitions to sdio.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Part of ath6kl uses "REV3" style of naming hardware versions and elsewhere
"hw 2.1.1" is used instead for the same version. This is confusing, use
the latter term everywhere.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to print name for each hardware type. Also move the hw
info print to ath6kl_init_hw_start() which is more logical place for it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Board data address can change between firmwares so we need to read that
from the firmware image.
Also fix debug log for the patch address to print the address in hex.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to make it configurable by firmware IEs. Also determine if we need
to write or read the board address to the chip by checking if board address
is set or not.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Having separate defines, in a different file, makes it difficult to read
the actual values. As we are just setting named fields in a struct
the defines don't make any sense anymore.
There are no functional changes, only moving of constants.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
OPEN_AUTH is passed as dot11_auth_mode by default, this would
affect the AP mode when configured with shared authentication
type. Assign appropriate auth type to fix this from driver.
A patch in wpa_supplicant (wpa_supplicant: Set configured auth_algs)
is also needed to fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vif->def_txkey_index is set to key_index in ath6kl_cfg80211_add_key().
If the interface is configured with multiple static wep keys,
vif->def_txkey_index would be holding the index of the last key configured,
not the default tx key index. Remove this unnecessary default key index setting
in ath6kl_cfg80211_add_key() to configure the right key index in WEP thereby
make it work when multiple wep keys are configured.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now two modules are built, ath6kl_sdio.ko and ath6kl_usb.ko. But the USB
module isn't fully functional yet as HTC layer is missing support and
that's why it's marked as experimental for now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As HTC layer doesn't support USB devices return an error if that happens.
USB support will be added to HTC in the future, this is just a temporary
solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add USB support for ar6004. Currently only firmware can be booted,
no commands can be sent to firmware yet as HTC layer doesn't work
with USB yet.
Based on patches by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some rare cases core code needs to know what hif type is used. Add
a field to struct ath6kl to denote that. Hopefully this is just a
temporary solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for AR6004 SDIO. Tested scan, association (open mode) and
ping.
kvalo: change commit log a bit, drop board address changes
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is preparation for USB support which will have different diag
commands.
Based on code by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The firmware expects the minimum length of
WMI_SEND_PROBE_RESPONSE_CMDID to be 13. However, when the device is a
P2P GO and it needs to send a probe response to a non-P2P client,
there are no P2P IEs to be added, and therefore the length of the WMI
command is 12. This command gets rejected by the firmware. To fix
this, add an extra byte to satisfy the minimum length requirement.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the connect event is received from the target in IBSS mode,
cfg80211_ibss_joined() is called without informing BSS info to
cfg80211 layer which internally hits the below WARN_ON message.
WARNING: at net/wireless/ibss.c:33 __cfg80211_ibss_joined+0x153/0x180 [cfg80211]()
[..]
[ 4916.845878] Call Trace:
[ 4916.845889] [<c10427d2>] warn_slowpath_common+0x72/0xa0
[ 4916.845905] [<f8bccc63>] ? __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845918] [<f8bccc63>] ? __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845923] [<c1042822>] warn_slowpath_null+0x22/0x30
[ 4916.845934] [<f8bccc63>] __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845941] [<c1025108>] ? default_spin_lock_flags+0x8/0x10
[ 4916.845952] [<f8bb7fcd>] cfg80211_process_rdev_events+0x19d/0x220 [cfg80211]
[ 4916.845962] [<f8bb669b>] cfg80211_event_work+0x2b/0x50 [cfg80211]
[ 4916.845968] [<c105aae6>] process_one_work+0x116/0x3c0
[ 4916.845977] [<f8bb6670>] ? cfg80211_get_dev_from_info+0x40/0x40 [cfg80211]
[ 4916.845982] [<c105cdf0>] worker_thread+0x140/0x3b0
[ 4916.845986] [<c105ccb0>] ? manage_workers+0x1f0/0x1f0
[ 4916.845991] [<c1060c64>] kthread+0x74/0x80
[ 4916.845995] [<c1060bf0>] ? kthread_worker_fn+0x160/0x160
[ 4916.846001] [<c14e7bbe>] kernel_thread_helper+0x6/0x10
[ 4916.846005] ---[ end trace 769254924e409367 ]---
This patch make sures that BSS info is delivered via cfg80211_inform_bss()
to cfg80211 in advance before intimating IBSS status to cfg80211.
In addition to this, one debug message is also added to know
ad-hoc mode status (creator/joiner).
kvalo: change subject
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
"ath6kl: Maintain virtual interface in a list" mistakenly stops the
netq only when the mode is ibss. This causes packet drops in sta mode
when the available cookies (buffer abstraction in ath6kl and also used
for tx throttling) runs out for the highest priority traffic. This patch
just fixes this regression though the original code may still need fixes
which can be addressed in separate patches.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When buffer alignmnet is applied, the data pointer of skb taken from
cookie will no longer point to the first byte of the actual data.
But the skb->data pointer is used in ath6kl_tx_complete() to get
the index of the virtual interface which will not give the correct
interface index and sometimes may give the following WARN_ON() message.
Use packet->buf instead of skb->data to fix this.
WARNING: at drivers/net/wireless/ath/ath6kl/wmi.c:88 ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]()
Hardware name: 2842K3U
Modules linked in: ath6kl mmc_block cfg80211 binfmt_misc ppdev nfs nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel
+snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy thinkpad_acpi snd_seq_oss snd_seq_midi snd_rawmidi joydev fbcon tileblit font bitblit softcursor
+snd_seq_midi_event snd_seq snd_timer snd_seq_device i915 uvcvideo drm_kms_helper drm psmouse serio_raw snd i2c_algo_bit sdhci_pci videodev intel_agp soundcore intel_gtt jmb38x_ms
+memstick sdhci snd_page_alloc nvram lp parport agpgart video ahci r8169 mii libahci [last unloaded: ath6kl]
Pid: 15482, comm: kworker/u:1 Tainted: G W 3.1.0-rc10-wl+ #2
Call Trace:
[<c0144d72>] warn_slowpath_common+0x72/0xa0
[<fb7c94fb>] ? ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
[<fb7c94fb>] ? ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
[<c0144dc2>] warn_slowpath_null+0x22/0x30
[<fb7c94fb>] ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
[<fb7c7028>] ath6kl_tx_complete+0x128/0x4d0 [ath6kl]
[<c04df920>] ? mmc_request_done+0x80/0x80
[<fb7b9e2e>] htc_tx_complete+0x5e/0x70 [ath6kl]
[<c05e4cf6>] ? _raw_spin_unlock_bh+0x16/0x20
[<fb7ce588>] ? ath6kl_sdio_scatter_req_add+0x48/0x60 [ath6kl]
[<fb7b9f42>] htc_async_tx_scat_complete+0xb2/0x120 [ath6kl]
[<fb7ce9e7>] ath6kl_sdio_scat_rw+0x87/0x370 [ath6kl]
[<c0101e12>] ? __switch_to+0xd2/0x190
[<c01397b5>] ? finish_task_switch+0x45/0xd0
[<c05e272e>] ? __schedule+0x3ae/0x8b0
[<fb7cf00a>] ath6kl_sdio_write_async_work+0x4a/0xf0 [ath6kl]
[<c015d266>] process_one_work+0x116/0x3c0
[<fb7cefc0>] ? ath6kl_sdio_read_write_sync+0xb0/0xb0 [ath6kl]
[<c015f5b0>] worker_thread+0x140/0x3b0
[<c015f470>] ? manage_workers+0x1f0/0x1f0
[<c0163424>] kthread+0x74/0x80
[<c01633b0>] ? kthread_worker_fn+0x160/0x160
[<c05ebdc6>] kernel_thread_helper+0x6/0x10
Reported-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is needed to know whether the STA requests WAPI to be used and if
so, with what AKM and cipher.
Signed-off-by: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate support for WPI-SMS4 cipher and allow SMS4 keys to be
configured.
Signed-off-by: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Retriving tx power for 2x2 and 3x3 chainmask is not handled
properly. While calculating tx power for 2x2, 3 dBm was reduced
and for 3x3, 5 dBm was reduced which should be added back when
retriving.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most ath9k devices are PCI/PCIe based, therefor making PCI/PCIe support
default y helps those porting a config from 2.6 kernel series
from getting "non-functional" wireless drivers with 3.x kernel series.
Signed-off-by: Daniel Kuehn <daniel@kuehn.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sync up CalFreqPeir channel list and paprd rate mask
of AR938x templates to the latest received from Systems team.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure xpa timing field while loading boad defaults to
fix 11b CCK spur issue that was observed in EMI testing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read and configure quick drop feild from AR9003 eeprom
inorder to help with strong signal. This patch also removes
obsolate parameters ob, db_stage2, db_stage_3, db_stage4
from the eeprom templates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
100 bytes are allocated to store the parameters which are needed
to create a priority stream. These 100 bytes are not sufficiant and
throws error when running the following command.
echo "6 2 3 1 1 9999999 9999999 9999999 7777777 0 6 45000 200 56789000
56789000 5678900 0 0 9999999 20000 0" > create_qos
179 bytes are needed when the following vlaues are given so that
a maximum possible value in that data type can be given in decimal.
echo "255 255 255 255 255 4294967295 4294967295 4294967295 4294967295
4294967295 255 65535 65535 4294967295 4294967295 4294967295 4294967295
4294967295 4294967295 4294967295 4294967295" > create_qos
Following takes 187 bytes when given in hex
echo "0xff 0xff 0xff 0xff 0xff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff
0xff 0xffff 0xffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff
0xffffffff 0xffffffff" > create_qos
Increase the size to 200 bytes so that it can hold upto the maximum
value possible for that data type.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
skb is dropped in ath6kl_data_tx() when the headroom in skb
is insufficient. We hit this condition for every skb in AP mode
which is used with bridge, so all tx packets are getting dropped
when tried to send traffic to wireless client from bridge. Fix
this by reallocating the headroom instead of dropping the skb
when it has lesser headroom than needed.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Removed unused WOW_MAX_FILTER_LISTS macro.
* Removed empty ath6kl_wmi_get_wow_list_event_rx() function.
List of configured WOW patterns are maintained in CFG layer
itself. No need to have this function in ath6kl to get
configured WOW pattern list. It can added later if we need
it for debugging.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the list of ath6kl's WOW trigger options in wiphy->wowlan.flags
variable during wiphy registration. So that, those options can be
configured via iw.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the current code, WOW resume is executed first from RX path
and ar->state is moved to ATH6KL_STATE_ON. When platform calls
ath6kl_sdio_resume() in CFG resume context, that time ar->state
could have moved to ON state. Printing WARN_ON(1) is void in
this context. Hence removing this.
Once WOW resume is removed from RX path, This WARN_ON msg can be
reverted.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The target triggers sdio data line to wake up the host when
WOW pattern matches. This causes sdio irq handler is being
executed in the host side which internally hits ath6kl's RX path.
WOW resume should happen before start processing any data from
the target. So it's required to perform WOW resume in RX path.
This area needs bit rework to avoid WOW resume in RX path,
As of now it's fine to have this model, rework will be done later.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Link ath6kl's wow suspend/resume functions with the actual suspend/resume path.
WOW mode is selected when the host sdio controller supports both
MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ capabilities.
kvalo: also adds a missing break in ath6kl_cfg80211_resume(), luckily
it didn't have any effect on functionality.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_cfg80211_stop() call is not applicable for WOW mode. Hence moving
this call to deep sleep and cut pwr specific cases.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In addition to existing deep sleep and cut pwr mode, new state
is added in ath6kl_cfg_suspend_mode as well as in ath6kl_state for WOW.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211 layer provides user defined wow parameters like Filter options, Patterns,
Pattern's mask, etc via "struct cfg80211_wowlan *wow" to suspend function.
Right now, this wowlan parameter is not handled in __ath6kl_cfg80211_suspend func.
This parameter has to be passed to HIF layer, So that it can be passed back to
ath6kl's cfg interface layer when WOW mode is selected.
In case of deep sleep and cut power mode, it's not handled.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is the core WOW suspend/resume functions will be called
in PM suspend/resume path.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It will be used in WOW suspend/resume functions to
active/deactivate WOW suspend mode.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These commands will be used in WOW suspend/resume functions
to configure WOW parameters like patterns to be matched
and it's mask value, etc.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of converting any error to EIO, just return the real error
value to upper layers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no guarantee on the caller using 8-octet buffer for
key->seq, so better follow the key->seq_len parameter on figuring
out how many octets to copy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to force ath6kl to power off hardware during suspend even if
sdio support keep power. This is needed, for example, when sdio
controller is buggy or maximum powersaving is desired.
Usage:
insmod ath6kl.ko suspend_cutpower=1
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jouni reported that my patch "ath6kl: power down hardware when interface
is down" caused a regression on his x86 boxes and scan didn't work anymore.
I was able to reproduce the problem by disabling all debug messages.
So there has to be a race condition somewhere in the code and disable the
functionality until the race is fixed. Now hardware is powered from the
point where module is loaded until it's removed.
Reported-by: Jouni Malinen <jouni@qca.qualcomm.com>
Tested-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The following is the lockdep warning which detects possible
deadlock condition with the way ar->lock and ar->list_lock
are being used.
(&(&ar->lock)->rlock){+.-...}, at: [<ffffffffa0492d13>] ath6kl_indicate_tx_activity+0x83/0x110 [ath6kl]
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&(&ar->list_lock)->rlock){+.+...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&ar->list_lock)->rlock);
local_irq_disable();
lock(&(&ar->lock)->rlock);
lock(&(&ar->list_lock)->rlock);
<Interrupt>
lock(&(&ar->lock)->rlock);
*** DEADLOCK ***
softirqs have to be disabled when acquiring ar->list_lock to avoid
the above deadlock condition. When the above warning printed the
interface is still up and running without issue.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If sdio controller doesn't support keep power, cut power from hardware
during suspend and restart firmware during resume. If we are connected
during suspend, send a disconnected event to user space.
Earlier suspend failed with an error if sdio didn't support keep power.
Now suspend will happen succesfully even with that case.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These commands are also needed after cutpower suspend so create
a function for them. Also fix memory leaks in ath6kl_sdio_probe() error
path.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This way it's easier to track state changes and in the future add
more warnings about using hardware in wrong states. Currently there
are few random flags for trying to do the same, those will be cleaned
and removed in the future.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is in preparation for cutpower suspend feature. HIF layer makes
the decision based on information provided by cfg80211 and what hardware
actually supports. Then it calls ath6kl_cfg80211_suspend() to enable
the chosen mode.
Functionality should be the same, this is just preparation for
more suspend modes (cutpower and wow).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it takes an error code as status, but what we really want to
tell is if the scan was aborted or not.
Also fix a bug where we were comparing firmware scan status values
with kernel error codes, which is obviously wrong. This meant
that ath6kl didn't detect when firmware informed about failed scans. I
doubt that this fix doesn't make any difference in practise but it
still needs to be fixed. This is fixed by adding an enum for the success
status code and checking for that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently firmware crash dump is printed only if debug is enabled.
Change it so that the crash dump is always printed.
Also move the code from init.c to hif.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If ath6kl_init_hw_stop() failed with an error WLAN_ENABLED would not
be cleared. Found during code review and just a theoretical issue.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The benefit from this is that user space can control hardware's power state
by putting interface up and down. This is handy if firmware gets to some
weird state.
The downside will be that putting interface up takes a bit longer,
I was measuring ~500 ms during interface up.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the name of the driver in struct sdio_driver is "ath6kl_sdio",
this is for example what uevent advertises. This is wrong as the module
is named as ath6kl.ko. Change it to "ath6kl" so that the names match.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_tx_complete() was printing an error when packet was canceled.
That causes unnecessary errors when hardware is powered off.
Also change the error to a warning and cleanup the message.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible to busyloop forever in ath6kl_hif_intr_bh_handler(). Add
a check that it lasts only one second.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Refactor the code needed to boot the hardware to a separate function so
that it will be easier boot and shutdown hardware.
No functional changes (hopefully).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use of cfg80211_scan_request is not valid after calling cfg80211_scan_done()
but ath6kl_cfg80211_scan_complete_event() was doing exactly that. Change
the function to call cfg80211_scan_done() last.
This was found during code review, I didn't see any visible problems
due to this bug.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wpa_supplicant was receiving incorrect frame contents in the
callback function that indicates the status of the frame transmitted.
This patch fixes a missing copy of the frame contents to a local
buffer. The local buffer keeps track of the last sent management frame.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though only a single concurrent remain-on-channel operation is
supported, there may be two pending remain-on-channel events (one to
indicate end of a canceled operation and another to indicate start of a
new operation). User space won't be able to distinguish these events
unless unique cookies are used.
The previous behavior resulted in wpa_supplicant getting quite
confused about the driver's offchannel state in various sequences
and this made the P2P state machine behave incorrectly. Use of
more than a single remain-on-channel cookie value fixes this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When compiling ath6kl for ARM with device tree tree compilation fails
with errors like:
include/linux/of.h: In function 'of_property_read_u32_array':
include/linux/of.h:249:10: error: 'ENOSYS' undeclared
Workaround this by including errno.h from init.c.
kvalo: improved commit log
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of power parameters, we use
available debugfs infrastructure. With these features user can control
power consumption by adjusting various sleep/wake up related parameters.
The feature has been added for testing purposes. All 5 parameters are
mandatory in correct order. They have to be written to the power_params
file. These are:
1) idle_period
2) no_of_pspoll
3) dtim_policy
4) tx_wakeup_policy
5) no_tx_to_wakeup
Example:
echo "200 1 0 1 1" > power_params
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of listen interval, we use
available debugfs infrastructure. Listen interval implies how frequently
we want the WLAN chip to wake up and synchronize the beacons in case it
is in sleep mode. The command requires two parameters in the following order:
1) listen_interval_time
2) listen_interval_beacons
The user has to write the listen interval_time (in msecs) and
listen_interval_beacons (in no. of beacons) to the listen_interval file in
ath6kl debug directory.
Example:
echo "30 1" > listen_interval
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add control flag CONNECT_WPS_FLAG if a WPS IE is present in the
Association Request IEs. This flag is needed when the station must
connect to a WPS-enabled AP.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move some of the debug logs to boot level because they are more
interesting when debugging boot issues.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove the wdev reference in struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wlan parameters need to be configured for every vif
in target.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This option lets operate more than one vif in normal mode (AP/STA/IBSS)
when support for multiple vif is enabled. This modparam needs to be used
as
modprobe ath6kl multi_norm_if_support=1
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Virtual interface information need to be configured during
init time to the target. With MAX_NUM_VIF is restricted to
1, currently only a single vif is being configured.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use replace (un)register_netdev() with (un)register_netdevice()
so that the same ath6kl function can be used with
add_virtual_intf()/del_virtual_intf().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch removes all references to ar->vif and takes
vif from a list.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use this spinlock to protect the vif's data instead of
one from ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI ready event gives the mac address, cache this
mac address in struct ath6kl so that it can be used to
compute the mac address for other vif in case of multi vif.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface index is passed in wmi data header as well, use it
to get the corresponding vif structure.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
So that the deinitialization of ath6kl and vif are separated.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass vif structure to those functions instead of ath6kl because these
functions do vif specific information initialization.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use one which is available in vif structure instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface index is passed in wmi command header from target.
Use this index to get the appropriate vif.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass this index to target in wmi commands to specify the interface
for which the command needs to be handled.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ar->flag maintains interface stats. Move interface
specific states from ar->flag to vif->flags.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vif specific information need to be moved from struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use ath6kl_get_fw_iftype() to find out the
firmware interface type during initialization because the type
of the initial interface in INFRA_NETWORK. Hardcode the fw interface
type corresponding to INFRA_BSS instead of using ath6kl_get_fw_iftype().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This refactoring is done in a manner that it can be used
for multiple virtual interface.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to avoid using ar->wdev to get wiphy pointer, this
may need further cleanup for multi vif support.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ar is again taken from private area of net_device in ath6kl_init(), pass
ar directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of background scan interval,
we use available debugfs infrastructure. The feature has been added for
testing purposes. The user has to write the bgscan interval (in secs) to
the bgscan_interval file in ath6kl debug directory. To disable bgscan,
a '0' is to be written to the bgscan_interval file.
Example:
echo "2" > bgscan_interval
This will make the background scan interval as 2 seconds
kvalo: changed implementation so that there's only one call to
ath6kl_wmi_scanparams_cmd()
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That way we htc level debug messages can be removed from hif files. Also
add few new messages and remove useless debug message about using
synchrous irq processing (we don't support anything else).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's currently possible to dump full sdio packets, so dumping htc packets
is not strictly needed. So remove it, we can always add it back if
there ever comes a need for that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based QOS control we use the available debugfs
infrastructure. With this feature, user can make changes to qos parameters,
thereby allowing creation and deletion of user defined priority streams and
features like uapsd. This feature has been added for testing purposes.
All 21 parameters for the create_qos command are mandatory in the correct
order. They have to be written to the create_qos file in
the ath6kl debug directory. These parameters(in order) are:
1)user priority
2)direction
3)traffic class
4)traffic type
5)voice PS capability
6)min service intvl
7)max service intvl
8)inactivity intvl
9)suspension intvl
10)serv start time
11)tsid
12)nominal msdu
13)max msdu
14)min data rate
15)mean data rate
16)peak data rate
17)max burst size
18)delay bound
19)min phy rate
20)surplus bw allowance
21)medium time
To create a qos stream:
echo "6 2 3 1 1 9999999 9999999 9999999 7777777 0 6 45000 200 56789000
56789000 5678900 0 0 9999999 20000 0" > create_qos
delete_qos requires 2 parameters:
1)traffic class
2)tsid
To delete a qos stream:
echo "3 1" > delete_qos
kvalo: minor commit log cleanup
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The previous version did not really make much sense and the theoretical
maximum length would be a bit longer. Calculate the length more
accurately. In addition, there is no need to clear the buffer, so use
kmalloc instead of kzalloc. For bonus points, add the forgotten
cred_rpt_from_other value to the file.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing {}'s that caused ath6kl_sdio_suspend to always return -EINVAL
causing suspend to be aborted.
kvalo: I broke this in commit f7325b85e ("ath6kl: add sdio debug messages")
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sangwook found out that commit 639d0b89 ("ath6kl: read firmware start
address from hardware") broke firmware boot on ar6003 hw2.0 as it seems
it's not posible to automatically query the address from hardware. So
we need to hardcode the address for hw2.0.
Reported-by: Sangwook Lee <sangwook.lee@linaro.org>
Tested-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use vendor-specific suite selectors to allow CCKM to be configured.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This file can be used to fetch endpoint statistics counters and
to clear them by writing 0 to it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some WPS test items, such as item "5.1.14"
STAUT must include the WSC IE in the 802.11 Association Request frame.
Therefore, add the corresponding IE in association message.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
smatch found that skb might be null in some cases in ath6kl_rx():
ath6kl/txrx.c +1252 ath6kl_rx(222) error: potential null derefence 'skb'.
This will happen when ath6kl is in AP mode and two clients send traffic
to each other.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Power save is enabled during ath6kl init. But when user space disables power
save, the system will go into suspend with power save disabled. The ath6kl
driver will now explicitly enable power save prior to entering suspend and
restore its previous setting upon resume
Signed-off-by: Chilam Ng <chilamng@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is just a four byte information of the received message
from ath6kl_htc_rxmsg_pending_handler(). Remove unnecessary
array representaion.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is found during the code review. As the leak would happen only
in failure case, the imapct is not easily visible.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface address so it can be mapped to a local
interface. Add max-ampdu and mpdu-density.
Print out the tid->baw_size
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test, TDLS seemed to be working fine with ath9k, so
let's start advertising support for this in the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initval tables are updated as per system team input to improve
rx performance and power accuracy at 5GHz.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve CCK sensitivity for AR9462 chips, performing
spur mitigation at 2440, 2464 frequencies alone is sufficient.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int. We should do the compare
as u32 instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
It only has module_param and EXPORT_SYMBOL, so now that export.h
is in scope at the same time as the recent ath5k update, we can
delete this module.h include.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were using moduleparam infrastructure, but were not
including anything for it -- which is fine when module.h is being
implicitly included in all files, but that is going away.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR946/8x chips are 2x2 Dual band with BT support. In order
to avoid misleading with other chips and to be in sync with
marketing team's term, AR9480 is renamed as AR9462.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported calibrations of radio retention table (RTT) are
- DC offset
- Filter
- Peak detect
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve sensitivity for AR9480, the normal and minimum
noise floor values of both bands are updated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Improve fast channel change for AR9003 chips"
fixes the fast channel change issue for AR9003 chips that was
originally observed in AR9382 chip. Hence enabling fastcc support
again for 11A channel for AR9003 chips.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass an argument to decide whether to reuse the Tx IQ
calibration measurements or not during fast channel change.
This will be later used by MCI support for AR9480.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.
This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 5G Tx gain table w/ XPA is updated to improve spur
performance in high_power Tx gain table.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9003 table is updated to increase XLNA BIAS
output driver strengh.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents lots of broken frames from showing up on monitor interfaces
by default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Fix incorrect key_miss handling" changed the code
to only report key miss errors if a MIC error wasn't reported.
When checking the flags in that order in the MAC code, it might miss some
real events, because the value of the MIC error flag is undefined under
some conditions.
The primary issue addressed by the previous commit is making sure that
MIC errors are properly reported on the STA side. This can be fixed in
a better way by adding a separate rx status flag for key miss and
ignoring it for multicast frames.
This fix slightly improves stability in AP mode on some older hardware,
like AR9132.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unused since the previous dead code that was using it had been
removed earlier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code for handling various restrictions concerning regulatory limits,
antenna gain, etc. is very convoluted and duplicated across various
EEPROM parsing implementations, making it hard to review.
This patch partially cleans up the mess by unifying regulatory limit
handling in one function and simplifying handling of antenna gain.
It also removes unused transmit power scaling arrays from the EEPROM code,
which belonged to an unimplemented API that isn't supposed to be in
the driver anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
