Fix the error path so that we can free the allocated memory on the error
path instead of releasing them individually on each error.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have requested for the firmware but we have missed releasing it both
on success and on error path.
While checking the code it turned out that the requested firmware is not
even used. More over the same firmware is being loaded by
wm0010_stage2_load().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the max register value of mic boost pga should be 3.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8962 can't support 64k sample rate. When playing a 64KHz wave file,
'Unsupported rate 64000Hz' will be prompted.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input PGAs have a gain range from -17.25dB to +30dB in 0.75dB steps.
The boost stage can provide additional gain. For line inputs, -12dB to
+6dB gain is available on the boost mixer. For micphone inputs, it can
provide up to +29dB additional gain from the microphone PGA.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The min gain is the corresponding gain value when the register value is 0
instead of 1, just correct it.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch removes the incorrect settings to avoid the pop sound in the
first playback with headphone after boot.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were aborting if the kzalloc of img_swap fails but without freeing the
already allocated out. Similarly we were aborting if spi_sync fails
without releasing out and img_swap.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/ics43432.c:66:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Ricard Wanderlof <ricard.wanderlof@axis.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add i2c shutdown function to prevent the pop sound of the headphone while
the system is rebooting or shutdowning. It de-initials the jack detection
function, and it cannot be turned off in _BIAS_OFF. If we don't de-initial
it, the pop sound will be heard in the situation of powering off. And
replace the related register settings from magic number to meaningful
defined name.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The extcon driver takes the DAPM mutex from within the interrupt thread
in several places, which makes it possible to get into a situation where
the interrupt thread is blocked waiting on the DAPM mutex whilst a DAPM
sequence is running which is attempting to configure the FLL. In this
case the FLL completion can't be completed as as the IRQ handler is
ONE_SHOT, which cause the FLL lock to use the full time out (250mS) and
report that the process timed out.
It is not really practical to make the extcon driver not take the DAPM
mutex from within the interrupt thread, at least not without extensive
modification. So this patch fixes the issue by switching the wait for
the FLL lock to polling. A few fast polls are done first as the FLL
should lock quickly for a good quality reference clock, (indeed it hits
on the first poll on my system) and it will poll every 20mS after that
until it times out.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch removes the incorrect setting of the JD mode. It will cause pop
sound in the booting time.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch corrects the sequence of the jack detection. It will prevent the
pop sound while the jack plug in.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the original calibration function and modify the depop and
calibration function to prevent the pop sound in the booting time.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added rt5677_spi_read() and refactored rt5677_spi_write() so that
an arbitrary block in the DSP address space can be read/written
via SPI. For example, this allows us to load an ELF DSP firmware
with sparse sections, and stream audio samples from DSP ring buffer.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Acked-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
