Currently, child nodes of the gpmc node are iterated and probed
regardless of their 'status' property. This means adding 'status =
"disabled";' has no effect.
This patch changes the iteration to only probe nodes marked as
available.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP platform device for TI DSP/Bridge is currently
created unconditionally whenever CONFIG_TIDSPBRIDGE is
enabled. This device should only be created on OMAP34xx/
OMAP36xx SoCs, and not for other OMAP3 derived SoCs or when
booting multi-arch images on other SoCs. So, add a check for
the SoC family both before creating the device and allocating
the carveout memory for the device.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap44xx_restart is defined as a static void inline when DRA7/AM437X is
defined alone, which implies that the restart function is no longer
functional even though it is built in. So, fix the definition of the
same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
- Reset fix for am43xx
- Proper OPP table for omap5
- Fix for SoC detection of one of the DRA7 SoCs
- hwmod updates to get SATA and OCP to work on omap5 (drivers merged in 3.16)
- ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was removed in
anticipation of a watchdog driver being merged for 3.16, and it didn't make
it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this point
but it slipped through cracks repeatedly while coming up the maintainer
chain and only affects the one SoC so risk is low.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=J9xD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
* Reset fix for am43xx
* Proper OPP table for omap5
* Fix for SoC detection of one of the DRA7 SoCs
* hwmod updates to get SATA and OCP to work on omap5 (drivers
merged in 3.16)
* ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was
removed in anticipation of a watchdog driver being merged for 3.16,
and it didn't make it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this
point but it slipped through cracks repeatedly while coming up the
maintainer chain and only affects the one SoC so risk is low"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add few more Keystone drivers
MAINTAINERS: merge MXS entry into IMX one
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
ARM: bcm: Fix bcm and multi_v7 defconfigs
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=eDSn
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.16 (round #2)
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
This partly reverts commits 553600502b (ARM: sunxi: Remove reset code from
the platform) and 5e669ec583 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.
This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTn/+wAAoJEBvUPslcq6Vzr1AP/1/HCOmp5B4tP3WhRPDK7nSr
hNjoa3uFhhpc6LoO1PMsbHcusBwrD9/Dr1BM53vltRXGGMFiADRw02N0BMSiDB4y
cWKo6C7d1PEsX7SvH6ehzQV6pB8v8zAhShuuA2sPQRcGsKPfUTCI3rjjvCNvcnmr
fIyLOwZ8MkFkAxrSCNUHULRK4U8Tivxa0k9eTEoPo+y5rkolTwtU9C5ybpUk4Jju
K1yjZOo+hbNENFLS4FqM6Y4IjlJlz49baDoaZXkIhP+UhvdKSLAhNta76vRtnnDE
wX0STSCYbPL/Tj+bfCk3VJa1dpgkHYY9y8H7FOsf0osqbP5j0H49i/+y3+lTu3A3
NzVYZRlu32llCp5pvVVy6ibjme9jRwz/HPtKEXDtbtFG41pvDaHnSF72OOVz6DoN
Yu9tN6vojMaeQeE69mFzy7RI6SWpOVxjHyPG1b2rGoJayY+P2oR43iPAeWF6q7lp
Nz/LWDqNwIj4H1T4KWIhK+mv/+YJDzWnIDczToK0ROZ8JOR3A0MRWwBvYpvHPRnY
rxE2vtRpHUqOPiPtj1sKzUti74xJahCL9oXLRuFbG4z5Le1jelM9dYdjf4wpAoWs
H+1RP20GRos1dNIzoPZieOP+X4jp0m6A1wtcy49Dbivw6Gx7oJecH7zkMvobgy8C
gJ8G86a9R4EXKNJmjqvc
=2HDE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
On Marvell Armada XP, when a CPU comes back from deep idle state of
cpuidle, it restarts its execution at armada_370_xp_cpu_resume(),
which puts back the CPU into the coherency, and then calls the generic
cpu_resume() function.
While this works on little-endian configurations, it doesn't work on
big-endian configurations because the CPU restarts in little-endian,
and therefore must be switched back to big-endian to operate
properly. To achieve this, a 'setend be' instruction must be executed
in big-endian configurations. However, the ARM_BE8() macro that is
used to implement nice compile-time conditional for ARM LE vs. ARM BE8
is not easily usable in inline assembly.
Therefore, this patch moves the armada_370_xp_cpu_resume() C function,
which was anyway just a block of inline assembly, into a proper
pmsu_ll.S file, and adds the appropriate ARM_BE8(setend be)
instruction.
Without this patch, an Armada XP big endian configuration with cpuidle
enabled fails to boot, as it hangs as soon as one of the CPU hits the
deep idle state.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404130165-3593-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 497a92308a ("ARM: mvebu:
implement L2/PCIe deadlock workaround") introduced some logic in
coherency.c to adjust the PL310 cache controller Device Tree node of
Armada 375 and Armada 38x platform to include the 'arm,io-coherent'
property if the system is running with hardware I/O coherency enabled.
However, with the L2CC driver cleanup done by Russell King, the
initialization of the L2CC driver has been moved earlier, and is now
part of the init_IRQ() ARM function in
arch/arm/kernel/irq.c. Therefore, calling coherency_init() in
->init_time() is now too late, as the Device Tree property gets added
too late (after the L2CC driver has been initialized).
In order to fix this, this commit removes the ->init_time() callback
use in board-v7.c and replaces it with an ->init_irq() callback. We
therefore no longer use the default ->init_irq() callback, but we now
use the default ->init_time() callback.
In this newly introduced ->init_irq() callback, we call irqchip_init()
which is the default behavior when ->init_irq() isn't defined, and
then do the initialization related to the coherency: SCU, coherency
fabric, and mvebu-mbus (which is needed to start secondary CPUs).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In preparation to a small re-organization of the initialization
sequence in board-v7.c, this commit moves the registration of the
custom external abort handler on Armada 375 later in the boot
sequence, and makes it more similar to the other quirks that we
already have. There is indeed no need to register this abort handler
particularly early, it simply needs to be registered before switching
to userspace.
In addition to this, this commit makes the registration of the custom
abort handler conditional on Armada 375 Z1, because Armada 375 A0 and
later iterations are not affected by the issue.
This commit was tested on both Armada 375 Z1 and Armada 375 A0
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reverts commit d26b17edaf
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
BCM (Kona/capri platform) has regressed in two ways on this release. First,
bcm_defconfig no longer selected the appropriate MMC driver options due to
changes in dependencies. Secondly, the new MFD and regulator drivers were not
enabled on multi_v7_defconfig, so that caused the system to fail probing MMC
there.
Fix by enabling the new options as needed.
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A new set of bug fixes for 3.16, containing patches for seven platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fJMs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A new set of bug fixes for 3.16, containing patches for seven
platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
ARM: integrator: fix OF-related regression
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: multi_v7_defconfig: Add QCOM GSBI driver
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
tty: serial: msm: Fix section mismatch warning
...
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTqvVyAAoJEAf03oE53VmQz+sH/2Di3RkT90URl9bGIiIgYh/S
NYg8gpasHEdxMtiDGp6c7ie9EWpIK1ga1F0Iha0fwYEJE/WOmlqEQYhXuoJyxKpJ
lJ2lfprj7Z19RjA717g+Q2LbAshTI1K3HhP2d56o97KkdmcIB76Re5DoGL14Ez6A
TP0sCTCGWO+brjPPmzDY0la2HezjMKmOnxtdu4sbysHe6RT9b6JcEa1cFsT0nh4j
DKdeyDO/kAp6sbkprkv7WCGpa+6fvsPEsnioO3IlYJx4ayT4Uq64YqS5skuzQK74
7TdTSZoq0OM87t/zY2NR5MGSPoi48fP4Z2O+m/L9PVzROCK44eXBKe4lzOArxKQ=
=D+rW
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
The at91sam9261 doesn't actually have a slow RC oscillator, remove it from the
dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull ARM fixes from Russell King:
"A number of low impact fixes, the most noticable one is the thumb2
frame pointer fix. We also fix a regression caused during this merge
window with ARM925 CPUs running with caches disabled, and fix a number
of warnings"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: arm925: ensure assembly sets up writethrough mapping
ARM: perf: fix compiler warning with gcc 4.6.4 (and tidy code)
ARM: l2c: fix dependencies on PL310 errata symbols
ARM: 8069/1: Make thread_save_fp macro aware of THUMB2 mode
ARM: 8068/1: scoop: Remove unused variable
Commit 07e461cd7e
"of: Ensure unique names without sacrificing determinism"
caused a boot failure regression on the Integrator machines.
The problem is probably caused by fiddling too much with
the device tree population in the OF init function, such
as passing the SoC bus device as parent when populating
the device tree.
This patch fixes the problem by:
- Avoiding to explicitly look up the tree root
- Look up devices needed before device population from
the match only, passing NULL as root
- Passing NULL as root and parent when calling
of_platform_populate()
After this the Integrators boot again. Tested on
Integrator/AP and Integrator/CP.
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Wildcards in compatible strings should be avoid. "marvell,armada38x"
was recently introduced but was not yet used.
The armada 385 SoC is a superset of the armada 380 SoC (with more CPUs
and more PCIe slots). So this patch replaces the use of
"marvell,armada38x" by the "marvell,armada380" string.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1403533011-21339-1-git-send-email-gregory.clement@free-electrons.com
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit eeb845459a
("ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id")
added phy-connection-type properties to ethernet PHY nodes.
Actually, the property has to be set for the ethernet port node instead.
Fix it by moving the corresponding properties to the correct nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1403555115-13111-1-git-send-email-sebastian.hesselbarth@gmail.com
Fixes: eeb845459a: ('ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id')
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTpUMjAAoJEFBXWFqHsHzOXm4IAKmUwbwRq3neZeRImgautENK
zyP0qtIaChqiJN+c0p23BSOnv6g914ORNPxbMIzdDVOEGC344ZOffWRQBBqSe9VR
XMifhdkhCiwtAXRRmsOBu5okBT/TjreFDfvwxssApkf9pdp/Hn3JeeDcxxGOoJr7
nIZSVGbKr0+wYTfPcnoloNUXqzTmk8WfDMvLNovE0U+MKsXtPzUvPUsJ9mNKiOAu
qkWltn5/rL8sD+onbtq/mHiPs2Lkb4ni8Duc3PggpvGCSoxmk8RTFC0YpMdXe8P6
DpfBsKfU18j0YDbOX07K8Qim0Wm1ODVvX6h/wlw+uSVwpk9aT6rbBaDlJNwhqUM=
=Bw+Y
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 3.16" from Shawn Guo:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
* tag 'imx-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: dts: hummingboard/cubox-i: move usb otg configuration to platform level
ARM: dts: cubox-i: add support for PWM-driven front panel LED
ARM: dts: imx6: ventana: correct gw52xx sgtl5000 clock source
ARM: dts: imx6qdl-gw5xxx: Fix Linear Technology vendor prefix
ARM: dts: imx6: ventana: fix include typo
ARM: dts: imx6sl: correct the fec ipg clock source
ARM: imx6sl: add missing enet clock for imx6sl
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3Mlm
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge Samsung fixes for 3.16 from Kukjin Kim:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: EXYNOS: fix pm code to check for cortex A9 rather than the SoC
clocksource: exynos_mct: Don't reset the counter during boot and resume
ARM: dts: fix reg sizes of GIC for exynos4
ARM: EXYNOS: Use wfi macro in platform_do_lowpower
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On exynos mcpm systems the firmware is hardcoded to jump to an address
in SRAM (0x02073000) when secondary CPUs come up. By default the
firmware puts a bunch of code at that location. That code expects the
kernel to fill in a few slots with addresses that it uses to jump back
to the kernel's entry point for secondary CPUs.
Originally (on prerelease hardware) this firmware code contained a
bunch of workarounds to deal with boot ROM bugs. However on all
shipped hardware we simply use this code to redirect to a kernel
function for bringing up the CPUs.
Let's stop relying on the code provided by the bootloader and just
plumb in our own (simple) code jump to the kernel. This has the nice
benefit of fixing problems due to the fact that older bootloaders
(like the one shipped on the Samsung Chromebook 2) might have put
slightly different code into this location.
Once suspend/resume is implemented for systems using exynos-mcpm we'll
need to make sure we reinstall our fixed up code after resume. ...but
that's not anything new since IRAM (and thus the address of the
mcpm_entry_point) is lost across suspend/resume anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The following commit:
89d7e5c mmc: sdhci-esdhc-imx: add runtime pm support
has the effect of also disabling the hardware card detect
in runtime pm.
We switch to GPIO based detection to avoid this issue.
This patch is based on:
ARM: dts: imx51-babbage: Fix esdhc setup
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit 89d7e5c131 (mmc: sdhci-esdhc-imx: add runtime pm
support), controller based card detection / write protection is not
supported anymore by esdhc driver. Let's use GPIO for CD/WP on esdhc1
instead.
While at it, fix cd gpio polarity for esdhc2. This is wrong and
currently only works because the imx esdhc driver ignores the polarity.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Move the display {} node out of the soc {} node . This just aligns
the DT with other boards, there is no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The "port" node was misplaced in the original patch, therefore making
the LCD dysfunctional on this board. Fix this by moving the "port" DT
node into the "display {}" node.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On Marvell Armada platforms, the PMSU (Power Management Service Unit)
controls a number of power management related activities, needed for
things like suspend/resume, CPU hotplug, cpuidle or even simply SMP.
Since cpuidle support was added for Armada XP, the pmsu.c file in
arch/arm/mach-mvebu/ calls the cpu_suspend() and cpu_resume() ARM
functions, which are only available when
CONFIG_ARM_CPU_SUSPEND=y. Therefore, configurations that have
CONFIG_ARM_CPU_SUSPEND disabled due to PM_SLEEP being disabled no
longer build properly, due to undefined references to cpu_suspend()
and cpu_resume().
To fix this, this patch simply ensures CONFIG_ARM_CPU_SUSPEND is
always enabled for Marvell EBU v7 platforms. Doing things in a more
fine-grained way would require a lot of #ifdef-ery in pmsu.c to
isolate the parts that use cpu_suspend()/cpu_resume(), and those parts
would anyway have been needed as soon as either one of suspend/resume,
CPU hotplug or cpuidle was enabled.
Reported-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402488397-31381-1-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently the mvebu boards need to detect the SoC revision in order to apply
some quirks needed to workaround issues found on I2C and thermal controllers
present only in very early SoC.
This detection requires PCI address translation to work, so we need to
explicitly select OF_ADDRESS_PCI.
This can be considered a partial revert of the following commit, that
wrongly removed the option selection:
commit 55400f3a1f
Author: Rob Herring <robh@kernel.org>
Date: Tue Apr 22 14:15:52 2014 -0500
ARM: mvebu: clean-up unneeded kconfig selects
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1402347165-19988-1-git-send-email-ezequiel.garcia@free-electrons.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since commit 39b9004d1f (gpu: ipu-v3: Move i.MX IPUv3 core driver out of
staging) the ipuv3 core driver is no longer built bey default.
Select CONFIG_IMX_IPUV3_CORE so that the core ipuv3 code can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Commit ca8f0b0a54 ("ARM: ensure C page table setup code follows
assembly code") did what it said on the tin, but some of the older
CPU code omitted the default cache policy from their files. This
results in the kernel running with the caches disabled. Fix this
for ARM925.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds QCOM GSBI config option to multi_v7_defconfig. Serial
driver on QCOM APQ8064 depends on GSBI driver, so without this patch
there is no serial console on IF6410 board using multi_v7_defconfig.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The fixes included are:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gew5
-----END PGP SIGNATURE-----
Merge tag 'sti-fixes-for-v3.16-rc1' of git://git.stlinux.com/devel/kernel/linux-sti into fixes
Merge "STi: DT fixes for v3.16" from Maxime Coquelin:
Couple of DT fixes for STi platform issues discovered on V3.16-rc1.
The fixes included are:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
* tag 'sti-fixes-for-v3.16-rc1' of git://git.stlinux.com/devel/kernel/linux-sti: (2963 commits)
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
ARM: STi: DT: Properly define sti-ethclk & stmmaceth for stih415/6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point. Unfortunately,
one of the two cleanups caused an unintended change in the original
version, so we had to revert one part of it and do some more testing
to ensure the rest is really fine. There was also a last-minute
rebase of the patches to remove another bad commit.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/Ylr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point.
Unfortunately, one of the two cleanups caused an unintended change in
the original version, so we had to revert one part of it and do some
more testing to ensure the rest is really fine. There was also a
last-minute rebase of the patches to remove another bad commit"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: use menuconfig for sub-arch menus
ARM: multi_v7_defconfig: re-enable SDHCI drivers
ARM: EXYNOS: Fix compilation warning
ARM: exynos: move sysram info to exynos.c
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 385 DB board
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 375 DB board
ARM: exynos: cleanup kconfig option display
misc: vexpress: fix error handling vexpress_syscfg_regmap_init()
ARM: Remove ARCH_HAS_CPUFREQ config option
ARM: integrator: fix section mismatch problem
ARM: mvebu: DT: fix OpenBlocks AX3-4 RAM size
ARM: samsung: make SAMSUNG_DMADEV optional
remoteproc: da8xx: don't select CMA on no-MMU
bus/arm-cci: add dependency on OF && CPU_V7
ARM: keystone requires ARM_PATCH_PHYS_VIRT
ARM: omap2: fix am43xx dependency on l2x0 cache
GCC 4.6.4 spits out the following warning when building perf_event_v7.c:
arch/arm/kernel/perf_event_v7.c: In function 'krait_pmu_get_event_idx':
arch/arm/kernel/perf_event_v7.c:1927:6: warning: 'bit' may be used uninitialized in this function
While upgrading the version of gcc may solve this, the code can also be
organised to be more efficient by not carrying more local variables than
is necessary across the armv7pmu_get_event_idx function call. If we set
'bit' to -1 (which is invalid for clear_bit) we can use that as an
indication whether we need to clear a bit after this function.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of configurations spit out warnings similar to:
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_588369 which has unmet direct dependencies (CACHE_L2X0)
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_727915 which has unmet direct dependencies (CACHE_L2X0)
Clean up the dependencies here:
* PL310 symbols should only be selected when CACHE_L2X0 is enabled.
* Since the cache-l2x0 code detects PL310 presence at runtime, and we will
eventually get rid of CACHE_PL310, surround these errata options with an
if CACHE_L2X0 conditional rather than repeating the dependency against
each.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Two reasons for this rename. Firstly, it removes the camel case
convention which isn't used by any other platform and secondly it
matches the naming convention for the internal kernel, which can
become annoying when flipping between the two.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Since commit:
commit d93003e8e4
Author: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Date: Thu Apr 24 22:58:30 2014 +0100
ARM: 8042/1: iwmmxt: allow to build iWMMXt on Marvell PJ4B
fixed the error that prevented Dove SoC from being built with
the rest of the mvebu SoCs, we can now add it to the defconfig.
In addition, this commit enables SERIAL_OF_PLATFORM, which is required
to have UART on some of the boards.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The clean up of CALLER_ADDR*() functions required the archs to either
use the default __builtin_return_address(X) (where X > 0) or override
it with something the arch can use. To override it, the arch would
define ftrace_return_address(x).
The arm architecture requires this to be redefined but instead of
defining ftrace_return_address(x) it defined ftrace_return_addr(x).
Fixes: eed542d696 (ftrace: Make CALLER_ADDRx macros more generic)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
