When CAVIUM_OCTEON_SOC is enabled, and MTD is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for MTD_COMPLEX_MAPPINGS
Depends on [n]: MTD [=n] && HAS_IOMEM [=y]
Selected by [y]:
- CAVIUM_OCTEON_SOC [=y] && <choice>
This is because CAVIUM_OCTEON_SOC selects MTD_COMPLEX_MAPPINGS,
without selecting or depending on MTD, despite MTD_COMPLEX_MAPPINGS
depending on MTD.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After commit 0ebeea8ca8 ("bpf: Restrict bpf_probe_read{, str}() only to
archs where they work"), bpf_probe_read{, str}() functions were no longer
available on MIPS, so there exist some errors when running bpf program:
root@linux:/home/loongson/bcc# python examples/tracing/task_switch.py
bpf: Failed to load program: Invalid argument
[...]
11: (85) call bpf_probe_read#4
unknown func bpf_probe_read#4
[...]
Exception: Failed to load BPF program count_sched: Invalid argument
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE should be restricted to archs
with non-overlapping address ranges, but they can overlap in EVA mode
on MIPS, so select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE if !EVA in
arch/mips/Kconfig, otherwise the bpf old helper bpf_probe_read() will
not be available.
This is similar with the commit d195b1d1d1 ("powerpc/bpf: Enable
bpf_probe_read{, str}() on powerpc again").
Fixes: 0ebeea8ca8 ("bpf: Restrict bpf_probe_read{, str}() only to archs where they work")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
+. LOONGSON64 use 0x98xx_xxxx_xxxx_xxxx as xphys cached, instread of
0xa8xx_xxxx_xxxx_xxxx
+. let CONFIG_MIPS_PGD_C0_CONTEXT depend on 64bit
+. cast CAC_BASE into u64 to silence warning on MIPS32
CP0 Context has enough room for wraping pgd into its 41-bit PTEBase field.
+. For XPHYS, the trick is that pgd is 4kB aligned, and the PABITS <= 53,
only save 53 - 12 = 41 bits, aka :
bit[63:59] | 0000 00 | bit[53:12] | 0000 0000 0000
+. for CKSEG0, only save 29 - 12 = 17 bits
when switching pgd, only need to save bit[53:12] or bit[28:12] into
CP0 Context's bit[63:23], see folling asm generated at run time
tlbmiss_handler_setup_pgd:
.set push
.set noreorder
dsra a2, a0, 29
move a3, a0
dins a0, zero, 29, 35
daddiu a2, a2, 4 //for CKSEG0, a2 from 0xfffffffffffffffc
//into 0
movn a0, a3, a2
dsll a0, a0, 11
jr ra
dmtc0 a0, CP0_CONTEXT
.set pop
when using it on page walking
dmfc0 k0, CP0_CONTEXT
dins k0, zero, 0, 23 // zero badv2
ori k0, k0, (CAC_BASE >> 53) // *prefix* with bit[63:59]
drotr k0, k0, 11 // kick it in the right place
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
KVM_GUEST is broken and unmaintained, so let's remove it.
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These are PCI based systems, so not enabling the support is rather
pointless. Additionally the random configѕ generated by the build bot
for IP27 and IP30 builds without PCI fail to buіld.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
MIPS doesn't have architecture-optimized bitsearching functions,
like find_{first,next}_bit() etc.
It's absolutely harmless to enable GENERIC_FIND_FIRST_BIT as this
functionality is not new at all and well-tested. It provides more
optimized code and saves some .text memory (32 R2):
add/remove: 4/1 grow/shrink: 1/53 up/down: 216/-372 (-156)
Users of for_each_set_bit() like hotpath gic_handle_shared_int()
will also benefit from this.
Suggested-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CPU_MIPS64 is supposed to be selected for CPUs that implement a revision
of the MIPS64 ISA. While it contains the generic ones, it forgot about
Octeon and Loongson in its list, which are indeed MIPS64 processors.
This commit adds these missing CPUs to the auto-selection list.
Cc: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: George Cherian <gcherian@marvell.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- added support for Realtek RTL83XX SoCs
- kaslr support for Loongson64
- first steps to get rid of set_fs()
- DMA runtime coherent/non-coherent selection cleanup
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=kQfQ
-----END PGP SIGNATURE-----
Merge tag 'mips_5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added support for Nintendo N64
- added support for Realtek RTL83XX SoCs
- kaslr support for Loongson64
- first steps to get rid of set_fs()
- DMA runtime coherent/non-coherent selection cleanup
- cleanups and fixes
* tag 'mips_5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (98 commits)
Revert "MIPS: Add basic support for ptrace single step"
vmlinux.lds.h: catch more UBSAN symbols into .data
MIPS: kernel: Drop kgdb_call_nmi_hook
MAINTAINERS: Add git tree for KVM/mips
MIPS: Use common way to parse elfcorehdr
MIPS: Simplify EVA cache handling
Revert "MIPS: kernel: {ftrace,kgdb}: Set correct address limit for cache flushes"
MIPS: remove CONFIG_DMA_PERDEV_COHERENT
MIPS: remove CONFIG_DMA_MAYBE_COHERENT
driver core: lift dma_default_coherent into common code
MIPS: refactor the runtime coherent vs noncoherent DMA indicators
MIPS/alchemy: factor out the DMA coherent setup
MIPS/malta: simplify plat_setup_iocoherency
MIPS: Add basic support for ptrace single step
MAINTAINERS: replace non-matching patterns for loongson{2,3}
MIPS: Make check condition for SDBBP consistent with EJTAG spec
mips: Replace lkml.org links with lore
Revert "MIPS: microMIPS: Fix the judgment of mm_jr16_op and mm_jalr_op"
MIPS: crash_dump.c: Simplify copy_oldmem_page()
Revert "mips: Manually call fdt_init_reserved_mem() method"
...
The "oprofile" user-space tools don't use the kernel OPROFILE support any more,
and haven't in a long time. User-space has been converted to the perf
interfaces.
The dcookies stuff is only used by the oprofile code. Now that oprofile's
support is getting removed from the kernel, there is no need for dcookies as
well.
Remove kernel's old oprofile and dcookies support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I2Ac
-----END PGP SIGNATURE-----
Merge tag 'oprofile-removal-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux
Pull oprofile and dcookies removal from Viresh Kumar:
"Remove oprofile and dcookies support
The 'oprofile' user-space tools don't use the kernel OPROFILE support
any more, and haven't in a long time. User-space has been converted to
the perf interfaces.
The dcookies stuff is only used by the oprofile code. Now that
oprofile's support is getting removed from the kernel, there is no
need for dcookies as well.
Remove kernel's old oprofile and dcookies support"
* tag 'oprofile-removal-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux:
fs: Remove dcookies support
drivers: Remove CONFIG_OPROFILE support
arch: xtensa: Remove CONFIG_OPROFILE support
arch: x86: Remove CONFIG_OPROFILE support
arch: sparc: Remove CONFIG_OPROFILE support
arch: sh: Remove CONFIG_OPROFILE support
arch: s390: Remove CONFIG_OPROFILE support
arch: powerpc: Remove oprofile
arch: powerpc: Stop building and using oprofile
arch: parisc: Remove CONFIG_OPROFILE support
arch: mips: Remove CONFIG_OPROFILE support
arch: microblaze: Remove CONFIG_OPROFILE support
arch: ia64: Remove rest of perfmon support
arch: ia64: Remove CONFIG_OPROFILE support
arch: hexagon: Don't select HAVE_OPROFILE
arch: arc: Remove CONFIG_OPROFILE support
arch: arm: Remove CONFIG_OPROFILE support
arch: alpha: Remove CONFIG_OPROFILE support
Just select DMA_NONCOHERENT and ARCH_HAS_SETUP_DMA_OPS from the
MIPS_GENERIC platform instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CONFIG_DMA_MAYBE_COHERENT just guards two early init options now. Just
enable them unconditionally for CONFIG_DMA_NONCOHERENT.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Lift the dma_default_coherent variable from the mips architecture code
to the driver core. This allows an architecture to sdefault all device
to be DMA coherent at run time, even if the kernel is build with support
for DMA noncoherent device. By allowing device_initialize to set the
->dma_coherent field to this default the amount of arch hooks required
for this behavior can be greatly reduced.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add perf_event_mips_regs/perf_reg_value/perf_reg_validate to support
features HAVE_PERF_REGS/HAVE_PERF_USER_STACK_DUMP in kernel.
[ayan@wavecomp.com: Repick this patch for unwinding userstack backtrace
by perf and libunwind on MIPS based CPU.]
[ralf@linux-mips.org: Add perf_get_regs_user() which is required after
'commit 88a7c26af8 ("perf: Move task_pt_regs sampling into arch code")'.]
[yangtiezhu@loongson.cn: Fix build error about perf_get_regs_user() after
commit 76a4efa809 ("perf/arch: Remove perf_sample_data::regs_user_copy"),
and also separate the original patches into two parts (MIPS kernel and perf
tools) to merge easily.]
The original patches:
https://lore.kernel.org/patchwork/patch/1126521/https://lore.kernel.org/patchwork/patch/1126520/
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Archer Yan <ayan@wavecomp.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This is just enough system to boot the kernel with earlycon working.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
kgdb fails to build when the FPU support is disabled:
arch/mips/kernel/kgdb.c: In function 'dbg_set_reg':
arch/mips/kernel/kgdb.c:147:35: error: 'struct thread_struct' has no member named 'fpu'
147 | memcpy((void *)¤t->thread.fpu.fcr31, mem,
| ^
arch/mips/kernel/kgdb.c:155:34: error: 'struct thread_struct' has no member named 'fpu'
155 | memcpy((void *)¤t->thread.fpu.fpr[fp_reg], mem,
This is only relevant for CONFIG_EXPERT=y, so disallowing it
in Kconfig is an easier workaround than fixing it properly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The kernel test robot keeps reporting the same bug when it
shows up in new files after random unrelated patches:
In file included from arch/mips/include/uapi/asm/byteorder.h:13,
from arch/mips/include/asm/bitops.h:20,
from include/linux/bitops.h:26,
from include/linux/kernel.h:12,
from include/linux/clk.h:13,
from drivers/base/regmap/regmap-mmio.c:7:
include/linux/byteorder/big_endian.h:8:2: warning: #warning inconsistent configuration, needs CONFIG_CPU_BIG_ENDIAN [-Wcpp]
8 | #warning inconsistent configuration, needs CONFIG_CPU_BIG_ENDIAN
| ^~~~~~~
drivers/base/regmap/regmap-mmio.c: In function 'regmap_mmio_gen_context':
>> drivers/base/regmap/regmap-mmio.c:274:2: error: duplicate case value
274 | case REGMAP_ENDIAN_NATIVE:
| ^~~~
drivers/base/regmap/regmap-mmio.c:246:2: note: previously used here
246 | case REGMAP_ENDIAN_NATIVE:
The problem is that some randconfig builds end up on the MIPS jazz
platform with neither CONFIG_CPU_BIG_ENDIAN nor CONFIG_CPU_LITTLE_ENDIAN
because no specific machine is selected. As it turns out, all jazz
machines support little-endian kernels, so this can simply be allowed
globally.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This reverts commit f9065b54d4.
We're adding Nintendo 64 support, so the VR4300 is no longer unused.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The "oprofile" user-space tools don't use the kernel OPROFILE support
any more, and haven't in a long time. User-space has been converted to
the perf interfaces.
Remove the old oprofile's architecture specific support.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Robert Richter <rric@kernel.org>
Acked-by: William Cohen <wcohen@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Now, after that all the sections are explicitly described and
declared in vmlinux.lds.S, we can enable ld orphan warnings to
prevent from missing any new sections in future.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
with mips converted to use of fs/config_binfmt_elf.c, there's no
need to keep selects of that thing all over arch/* - we can simply
turn into def_bool y if COMPAT && BINFMT_ELF (in fs/Kconfig.binfmt)
and get rid of all selects.
Several architectures got those selects wrong (e.g. you could
end up with sparc64 sans BINFMT_ELF, with select violating
dependencies, etc.)
Randy Dunlap has spotted some of those; IMO this is simpler than
his fix, but it depends upon the stuff that would need to be
backported, so we might end up using his variant for -stable.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Like amd64, mips has two 32bit ABIs - o32 and n32. Unlike amd64,
it does not use compat_binfmt_elf.c for either of those; each
of those ABIs has a binfmt handler of its own, both very similar
to fs/compat_binfmt_elf.c. And the same technics as we use on
amd64 can be used to make fs/compat_binfmt_elf.c handle both.
* merge elfo32_check_arch() with elfn32_check_arch(),
make that serve as compat_elf_check_arch(). Note that
SET_PERSONALITY2() is already the same for all ABI variants -
it looks at the elf header to choose the flags to set.
* add asm/elfcore-compat.h, using the bigger (n32) variant
of elf32_prstatus as compat_elf_prstatus there.
* make PRSTATUS_SIZE() and SET_PR_FPVALID() choose the
right layout, same as done for amd64. test_thread_flag(TIF_32BIT_REGS)
is used as the predicate.
Voila - we are rid of binfmt_elf{n,o}32.c; fs/compat_binfmt_elf.c is
used, same as for all other ELF-supporting 64bit architectures that
need 32bit compat.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
RM7000 IRQ driver never got really used by any of the platform,
and rm9k_cpu_irq_init only exist in a header.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In the current code, we can not build under !CONFIG_NUMA and !CONFIG_SMP
on the Loongson64 platform, it seems bad for the users who just want to
use pure single core (not nosmp) to debug, so do the following things to
give them a chance:
(1) Do not select NUMA and SMP for MACH_LOONGSON64 in Kconfig, make NUMA
depends on SMP, and then just set them in the loongson3_defconfig.
(2) Move szmem() from numa.c to init.c and add prom_init_memory() under
!CONFIG_NUMA.
(3) Clean up szmem() due to the statements of case SYSTEM_RAM_LOW and
SYSTEM_RAM_HIGH are the same.
(4) Remove the useless declaration of prom_init_memory() and add the
declaration of szmem() in loongson.h to avoid build error.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- enabled GCOV
- reworked setup of protection map
- added support for more MSCC platforms
- added sysfs boardinfo for Loongson64
- enabled KASLR for Loogson64
- added reset controller for BCM63xx
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=0Sht
-----END PGP SIGNATURE-----
Merge tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- enable GCOV
- rework setup of protection map
- add support for more MSCC platforms
- add sysfs boardinfo for Loongson64
- enable KASLR for Loogson64
- add reset controller for BCM63xx
- cleanups and fixes
* tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (70 commits)
mips: fix Section mismatch in reference
MAINTAINERS: Add linux-mips mailing list to JZ47xx entries
MAINTAINERS: Remove JZ4780 DMA driver entry
MAINTAINERS: chenhc@lemote.com -> chenhuacai@kernel.org
MIPS: Octeon: irq: Alloc desc before configuring IRQ
MIPS: mm: Add back define for PAGE_SHARED
MIPS: Select ARCH_KEEP_MEMBLOCK if DEBUG_KERNEL to enable sysfs memblock debug
mips: lib: uncached: fix non-standard usage of variable 'sp'
MIPS: DTS: img: Fix schema warnings for pwm-leds
MIPS: KASLR: Avoid endless loop in sync_icache if synci_step is zero
MIPS: Move memblock_dump_all() to the end of setup_arch()
MIPS: SMP-CPS: Add support for irq migration when CPU offline
MIPS: OCTEON: Don't add kernel sections into memblock allocator
MIPS: Don't round up kernel sections size for memblock_add()
MIPS: Enable GCOV
MIPS: configs: drop unused BACKLIGHT_GENERIC option
MIPS: Loongson64: Fix up reserving kernel memory range
MIPS: mm: Remove unused is_aligned_hugepage_range
MIPS: No need to check CPU 0 in {loongson3,bmips,octeon}_cpu_disable()
mips: cdmm: fix use-after-free in mips_cdmm_bus_discover
...
This cleans up two ancient timer features that were never completed in
the past, CONFIG_GENERIC_CLOCKEVENTS and CONFIG_ARCH_USES_GETTIMEOFFSET.
There was only one user left for the ARCH_USES_GETTIMEOFFSET variant
of clocksource implementations, the ARM EBSA110 platform. Rather than
changing to use modern timekeeping, we remove the platform entirely as
Russell no longer uses his machine and nobody else seems to have one
any more.
The conditional code for using arch_gettimeoffset() is removed as
a result.
For CONFIG_GENERIC_CLOCKEVENTS, there are still a couple of platforms
not using clockevent drivers: parisc, ia64, most of m68k, and one
Arm platform. These all do timer ticks slighly differently, and this
gets cleaned up to the point they at least all call the same helper
function. Instead of most platforms using 'select GENERIC_CLOCKEVENTS'
in Kconfig, the polarity is now reversed, with the few remaining ones
selecting LEGACY_TIMER_TICK instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=QpNs
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-timers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cross-architecture timer cleanup from Arnd Bergmann:
"This cleans up two ancient timer features that were never completed in
the past, CONFIG_GENERIC_CLOCKEVENTS and CONFIG_ARCH_USES_GETTIMEOFFSET.
There was only one user left for the ARCH_USES_GETTIMEOFFSET variant
of clocksource implementations, the ARM EBSA110 platform. Rather than
changing to use modern timekeeping, we remove the platform entirely as
Russell no longer uses his machine and nobody else seems to have one
any more.
The conditional code for using arch_gettimeoffset() is removed as a
result.
For CONFIG_GENERIC_CLOCKEVENTS, there are still a couple of platforms
not using clockevent drivers: parisc, ia64, most of m68k, and one Arm
platform. These all do timer ticks slighly differently, and this gets
cleaned up to the point they at least all call the same helper
function.
Instead of most platforms using 'select GENERIC_CLOCKEVENTS' in
Kconfig, the polarity is now reversed, with the few remaining ones
selecting LEGACY_TIMER_TICK instead"
* tag 'asm-generic-timers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
timekeeping: default GENERIC_CLOCKEVENTS to enabled
timekeeping: remove xtime_update
m68k: remove timer_interrupt() function
m68k: change remaining timers to legacy_timer_tick
m68k: m68328: use legacy_timer_tick()
m68k: sun3/sun3c: use legacy_timer_tick
m68k: split heartbeat out of timer function
m68k: coldfire: use legacy_timer_tick()
parisc: use legacy_timer_tick
ARM: rpc: use legacy_timer_tick
ia64: convert to legacy_timer_tick
timekeeping: add CONFIG_LEGACY_TIMER_TICK
timekeeping: remove arch_gettimeoffset
net: remove am79c961a driver
ARM: remove ebsa110 platform
In the current code, CONFIG_ARCH_KEEP_MEMBLOCK is not set for MIPS arch,
memblock_discard() will discard memory and reserved arrays if they were
allocated, select ARCH_KEEP_MEMBLOCK if DEBUG_KERNEL to give a chance to
track "memory" and "reserved" memblocks after early boot, with this patch,
we can see the following two sysfs interfaces under DEBUG_FS.
/sys/kernel/debug/memblock/memory
/sys/kernel/debug/memblock/reserved
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Currently we won't migrate irqs when offline CPUs, which has been
implemented on most architectures. That will lead to some devices work
incorrectly if the bound cores are offline.
While that can be easily supported by enabling GENERIC_IRQ_MIGRATION.
But i don't pretty known the reason it was not supported on all MIPS
platforms.
This patch add the support for irq migration on MIPS CPS platform, and
it's tested on the interAptiv processor.
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Enable gcov profiling of the entire kernel on mips. Required changes
include disabling profiling for:
* arch/kernel/boot/compressed: not linked to main kernel.
Lightly tested on Loongson 3A3000 an 3A4000, seems to work as expected.
without "GCOV_PROFILE := n" in compressed Makefile,
build errors as follows:
...
ld: arch/mips/boot/compressed/string.o:(.data+0x88):
undefined reference to `__gcov_merge_add'
ld: arch/mips/boot/compressed/string.o:
in function `_GLOBAL__sub_I_00100_0_memcpy':
string.c:(.text.startup+0x4): undefined reference to `__gcov_init'
ld: arch/mips/boot/compressed/string.o:
in function `_GLOBAL__sub_D_00100_1_memcpy':
string.c:(.text.exit+0x0): undefined reference to `__gcov_exit'
...
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Xingxing Su <suxingxing@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Provide a weak plat_get_fdt() in relocate.c in case some platform enable
USE_OF while plat_get_fdt() is useless.
1MB RELOCATION_TABLE_SIZE is small for Loongson64 because too many
instructions should be relocated. 2MB is enough in present.
Add KASLR support for Loongson64.
KASLR(kernel address space layout randomization)
To enable KASLR on Loongson64:
First, make loongson3_defconfig.
Then, enable CONFIG_RELOCATABLE and CONFIG_RANDOMIZE_BASE.
Finally, compile the kernel.
To test KASLR on Loongson64:
Start machine with KASLR kernel.
The first time:
# cat /proc/iomem
00200000-0effffff : System RAM
02f30000-03895e9f : Kernel code
03895ea0-03bc7fff : Kernel data
03e30000-04f43f7f : Kernel bss
The second time:
# cat /proc/iomem
00200000-0effffff : System RAM
022f0000-02c55e9f : Kernel code
02c55ea0-02f87fff : Kernel data
031f0000-04303f7f : Kernel bss
We see that code, data and bss sections become randomize.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
No reason having the same code in every architecture
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201103095857.885321106@linutronix.de
There are a few spelling mistakes in the Kconfig, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Almost all machines use GENERIC_CLOCKEVENTS, so it feels wrong to
require each one to select that symbol manually.
Instead, enable it whenever CONFIG_LEGACY_TIMER_TICK is disabled as
a simplification. It should be possible to select both
GENERIC_CLOCKEVENTS and LEGACY_TIMER_TICK from an architecture now
and decide at runtime between the two.
For the clockevents arch-support.txt file, this means that additional
architectures are marked as TODO when they have at least one machine
that still uses LEGACY_TIMER_TICK, rather than being marked 'ok' when
at least one machine has been converted. This means that both m68k and
arm (for riscpc) revert to TODO.
At this point, we could just always enable CONFIG_GENERIC_CLOCKEVENTS
rather than leaving it off when not needed. I built an m68k
defconfig kernel (using gcc-10.1.0) and found that this would add
around 5.5KB in kernel image size:
text data bss dec hex filename
3861936 1092236 196656 5150828 4e986c obj-m68k/vmlinux-no-clockevent
3866201 1093832 196184 5156217 4ead79 obj-m68k/vmlinux-clockevent
On Arm (MACH_RPC), that difference appears to be twice as large,
around 11KB on top of an 6MB vmlinux.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull initial set_fs() removal from Al Viro:
"Christoph's set_fs base series + fixups"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Allow a NULL pos pointer to __kernel_read
fs: Allow a NULL pos pointer to __kernel_write
powerpc: remove address space overrides using set_fs()
powerpc: use non-set_fs based maccess routines
x86: remove address space overrides using set_fs()
x86: make TASK_SIZE_MAX usable from assembly code
x86: move PAGE_OFFSET, TASK_SIZE & friends to page_{32,64}_types.h
lkdtm: remove set_fs-based tests
test_bitmap: remove user bitmap tests
uaccess: add infrastructure for kernel builds with set_fs()
fs: don't allow splice read/write without explicit ops
fs: don't allow kernel reads and writes without iter ops
sysctl: Convert to iter interfaces
proc: add a read_iter method to proc proc_ops
proc: cleanup the compat vs no compat file ops
proc: remove a level of indentation in proc_get_inode
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make usage
of usage of 16byte load/stores possible
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=Aa/Q
-----END PGP SIGNATURE-----
Merge tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make use
of 16byte load/stores possible
- cleanups and fixes
* tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (92 commits)
MIPS: DEC: Restore bootmem reservation for firmware working memory area
MIPS: dec: fix section mismatch
bcm963xx_tag.h: fix duplicated word
mips: ralink: enable zboot support
MIPS: ingenic: Remove CPU_SUPPORTS_HUGEPAGES
MIPS: cpu-probe: remove MIPS_CPU_BP_GHIST option bit
MIPS: cpu-probe: introduce exclusive R3k CPU probe
MIPS: cpu-probe: move fpu probing/handling into its own file
MIPS: replace add_memory_region with memblock
MIPS: Loongson64: Clean up numa.c
MIPS: Loongson64: Select SMP in Kconfig to avoid build error
mips: octeon: Add Ubiquiti E200 and E220 boards
MIPS: SGI-IP28: disable use of ll/sc in kernel
MIPS: tx49xx: move tx4939_add_memory_regions into only user
MIPS: pgtable: Remove used PAGE_USERIO define
MIPS: alchemy: Share prom_init implementation
MIPS: alchemy: Fix build breakage, if TOUCHSCREEN_WM97XX is disabled
MIPS: process: include exec.h header in process.c
MIPS: process: Add prototype for function arch_dup_task_struct
MIPS: idle: Add prototype for function check_wait
...
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
- heavily refactor seccomp selftests (and clone3 selftests dependency) to
fix powerpc (Kees Cook, Thadeu Lima de Souza Cascardo)
- fix style issue in selftests (Zou Wei)
- upgrade "unknown action" from KILL_THREAD to KILL_PROCESS (Rich Felker)
- replace task_pt_regs(current) with current_pt_regs() (Denis Efremov)
- fix corner-case race in USER_NOTIF (Jann Horn)
- make CONFIG_SECCOMP no longer per-arch (YiFei Zhu)
-----BEGIN PGP SIGNATURE-----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=a4u2
-----END PGP SIGNATURE-----
Merge tag 'seccomp-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp updates from Kees Cook:
"The bulk of the changes are with the seccomp selftests to accommodate
some powerpc-specific behavioral characteristics. Additional cleanups,
fixes, and improvements are also included:
- heavily refactor seccomp selftests (and clone3 selftests
dependency) to fix powerpc (Kees Cook, Thadeu Lima de Souza
Cascardo)
- fix style issue in selftests (Zou Wei)
- upgrade "unknown action" from KILL_THREAD to KILL_PROCESS (Rich
Felker)
- replace task_pt_regs(current) with current_pt_regs() (Denis
Efremov)
- fix corner-case race in USER_NOTIF (Jann Horn)
- make CONFIG_SECCOMP no longer per-arch (YiFei Zhu)"
* tag 'seccomp-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
seccomp: Make duplicate listener detection non-racy
seccomp: Move config option SECCOMP to arch/Kconfig
selftests/clone3: Avoid OS-defined clone_args
selftests/seccomp: powerpc: Set syscall return during ptrace syscall exit
selftests/seccomp: Allow syscall nr and ret value to be set separately
selftests/seccomp: Record syscall during ptrace entry
selftests/seccomp: powerpc: Fix seccomp return value testing
selftests/seccomp: Remove SYSCALL_NUM_RET_SHARE_REG in favor of SYSCALL_RET_SET
selftests/seccomp: Avoid redundant register flushes
selftests/seccomp: Convert REGSET calls into ARCH_GETREG/ARCH_SETREG
selftests/seccomp: Convert HAVE_GETREG into ARCH_GETREG/ARCH_SETREG
selftests/seccomp: Remove syscall setting #ifdefs
selftests/seccomp: mips: Remove O32-specific macro
selftests/seccomp: arm64: Define SYSCALL_NUM_SET macro
selftests/seccomp: arm: Define SYSCALL_NUM_SET macro
selftests/seccomp: mips: Define SYSCALL_NUM_SET macro
selftests/seccomp: Provide generic syscall setting macro
selftests/seccomp: Refactor arch register macros to avoid xtensa special case
selftests/seccomp: Use __NR_mknodat instead of __NR_mknod
selftests/seccomp: Use bitwise instead of arithmetic operator for flags
...
Some of these ralink devices come with an ancient u-boot which can't
extract LZMA properly when image gets too big.
Enable zboot support to get a self-extracting kernel instead of relying
on broken u-boot support.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
While it is true that Ingenic SoCs support huge pages, we cannot use
them yet as PTEs don't have any single bit that is free. Right now,
having that symbol only causes build errors, so remove it until the
situation with PTEs is resolved.
Fixes: f0f4a75307 ("MIPS: generic: Add support for Ingenic SoCs")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
devices which require non-PCI based MSI handling.
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which allows
to utilize the full functionality of hierarchical irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the irqdomain
which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch and
let the last few users select it.
-----BEGIN PGP SIGNATURE-----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=JlqV
-----END PGP SIGNATURE-----
Merge tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
In the current code, CONFIG_SMP can be set as N by user on the Loongson
platform, then there exists the following build error under !CONFIG_SMP:
CC arch/mips/kernel/asm-offsets.s
In file included from ./include/linux/gfp.h:9:0,
from ./include/linux/xarray.h:14,
from ./include/linux/radix-tree.h:18,
from ./include/linux/fs.h:15,
from ./include/linux/compat.h:17,
from arch/mips/kernel/asm-offsets.c:12:
./include/linux/topology.h: In function 'numa_node_id':
./include/linux/topology.h:119:2: error: implicit declaration of function 'cpu_logical_map' [-Werror=implicit-function-declaration]
return cpu_to_node(raw_smp_processor_id());
^
cc1: some warnings being treated as errors
scripts/Makefile.build:117: recipe for target 'arch/mips/kernel/asm-offsets.s' failed
make[1]: *** [arch/mips/kernel/asm-offsets.s] Error 1
Select SMP in Kconfig to avoid the above build error and then remove
CONFIG_SMP=y in loongson3_defconfig.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In order to make adding configurable features into seccomp easier,
it's better to have the options at one single location, considering
especially that the bulk of seccomp code is arch-independent. An quick
look also show that many SECCOMP descriptions are outdated; they talk
about /proc rather than prctl.
As a result of moving the config option and keeping it default on,
architectures arm, arm64, csky, riscv, sh, and xtensa did not have SECCOMP
on by default prior to this and SECCOMP will be default in this change.
Architectures microblaze, mips, powerpc, s390, sh, and sparc have an
outdated depend on PROC_FS and this dependency is removed in this change.
Suggested-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/lkml/CAG48ez1YWz9cnp08UZgeieYRhHdqh-ch7aNwc4JRBnGyrmgfMg@mail.gmail.com/
Signed-off-by: YiFei Zhu <yifeifz2@illinois.edu>
[kees: added HAVE_ARCH_SECCOMP help text, tweaked wording]
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/9ede6ef35c847e58d61e476c6a39540520066613.1600951211.git.yifeifz2@illinois.edu
The unconditional selection of PCI_MSI_ARCH_FALLBACKS has an unmet
dependency because PCI_MSI_ARCH_FALLBACKS is defined in a 'if PCI' clause.
As it is only relevant when PCI_MSI is enabled, update the affected
architecture Kconfigs to make the selection of PCI_MSI_ARCH_FALLBACKS
depend on 'if PCI_MSI'.
Fixes: 077ee78e39 ("PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable")
Reported-by: Qian Cai <cai@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Links: https://lore.kernel.org/r/cdfd63305caa57785b0925dd24c0711ea02c8527.camel@redhat.com
There is nothing that prevents us from using lower maximum values.
It's something that we actually want, when using bigger page sizes on
devices with low RAM.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
All users are gone now, remove the API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> (MIPS part)
Now that all the jz4740 platform code has been removed, and we're left
with only a Kconfig and the cpu-feature-overrides.h file, finalize the
cleanup process by renaming the jz4740 and include/mach-jz4740 folders
to ingenic and include/mach-ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for Ingenic SoCs in arch/mips/generic/.
The Kconfig changes are here to ensure that it is possible to compile
either a generic kernel that supports Ingenic SoCs, or a Ingenic-only
kernel, both using the same code base, to avoid duplicated code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There is no reason we can't create compressed kernels here, so select
the option SYS_SUPPORTS_ZBOOT.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
