This patch adds support for parsing WMM IEs from hostapd
and setting them to FW via sys configure command.
Patch also sets wiphy flag to advertise AP uAPSD support.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for multiple TX queues inside mwifiex
driver. Four different queues according to WMM access categories
are defined for each virtual interface. When a packet is
received from netdev for transmission, tx pending count for
particular queue is incremented and if tx pending count has
reached upper water-mark, this queue is stopped instead of
stopping all queues. Similarly when a packet is successfully
transmitted from device, tx pending count is decremented per
queue and if pending count falls below lower water-mark, queue
operations are again resumed. This ensures that not all
tranmission is blocked if traffic with particular TOS value
suddenly increases.
Also wake all queues after association/IBSS_join/uAP_BSS_start
to enable traffic on all queues.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command timeout happens due to a bug in firmware/hardware,
the timeout handler just prints some debug information. User is
unable to reload the driver in this case.
Inspired by 9a821f5 "libertas: add sd8686 reset_card support",
this patch adds card reset support for SDIO interface when
command timeout happens. If the SDIO host contoller supports
MMC_POWER_OFF|UP|ON operations, the chip will be reset and the
firmware will be re-downloaded.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We derive mwifiex_private structure which is per interface from
received skb's rx_info. Once priv is derived, same priv can be
propagated to other functions instead of callee deriving priv
from rx_info again.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_request_scan() takes care of synchronous internal scan
performed by driver during association.
Currently the semaphore acquired for the scan is unnecessarily
released at the end of different paths. Also, failure paths
returning error code other than "-1" are not considered.
We will release it at the end of routine to fix above issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DBG_CMD_NUM is the number of commands, not the actual bytes of
data for printing.
Also remove the duplicated DBG_CMD_NUM definition.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver gets LINK_LOST, DEAUTHENTICATED and DISASSOCIATED events
from firmware when connection is lost in different scenarios.
Currently we are using common code WLAN_REASON_DEAUTH_LEAVING
for these cases.
This patch adds support to parse an actual reason code from
firmware event body and send it to cfg80211.
WLAN_REASON_DEAUTH_LEAVING code is used if deauth is initiated
by our device.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once hostsleep is activated, this patch takes care of not
dropping packets in RX reorder table.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cfg80211 calls to change interface type for P2P GO, send
P2P mode config commands to firmware and set bss role and bss
mode accordingly.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to implement remain_on_channel and
cancel_remain_on_channel.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process the management frames received from firmware and report
them to cfg80211.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to implement mgmt_frame_register.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement mgmt_tx in cfg80211 ops through data path.
Advertise probe resp offload and skip to send probe resp in AP
or GO mode.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently scan operation is delayed/aborted based on Tx traffic
consistency. This decision is taken after receiving scan
response of first scan command from FW. But when heavy traffic
is running, we can not even afford to send first scan command
and go off channel for 30msec. We will block scan request in
this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds separate tx packet descriptor routine for AP
interface. This function fills bss_type, bss_num, wmm packet
delay information etc for TxPD going on AP interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since mwifiex_ds_misc_subsc_evt is used in an asynchronous case,
store the structure in the long-lived mwifiex_private instead of
on the calling stack.
This fixes a problem where the response of the asynchronous
operation would corrupt a stack frame potentially in use by
a different thread.
Signed-off-by: Jeff Disher <disher@chromium.org>
Reviewed-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Jeff Disher <disher@chromium.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing rates from cfg80211_ap_settings
of start_ap handler. This in turn adds support for 11a and 11b phy
configurations.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cipher' and 'seq' coming from cfg80211 add_key handler will be
parsed in mwifiex_set_encode() to handle AES_CMAC cipher suite.
Signed-off-by: Ying Luo <luoy@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for handling BA request and BA setup
events for AP interface.
RA list is marked as either 11n enabled or disabled from station's
capabilities in association request. BA setup is initiated only
after some specific number of packets for particular RA list are
transmitted.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Separate file for uAP RX handling.
2. If received packet is broadcast/multicast, send it to kernel
as well as requeue it back to uAP TX queue.
3. If received packet is for associated STA (intra-BSS), requeue
it back to uAP TX queue.
4. In all other cases (packets for AP or inter-BSS packets),
pass packet to kernel to handle it accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After station is associated an entry would be added to station
list. This entry would have station specific information such as
11n support, AMSDU size. The entry would be deleted after
deauthentication. All station entries would be deleted during
BSS_IDLE event.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Route AP events handling to separate function defined in
uap_event.c.
AP specific event handling is removed from sta_event.c.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If HT IE is present in beacon_data of start_ap cfg80211 handler,
enable 11n flag in AP. Disable 11n flag when stop_ap handler is
called.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier scan command was postponed by 20msec multiple times to give
preference to Tx traffic until we find empty wmm queue.
There is a corner case in which wmm queue becomes empty immediately
after processing the packet(before 20msec) and there may be next
packet coming after some time. In this case we should not resume scan
operation.
We will use new flag to check Tx traffic and resume scan operation
only if there is no traffic for 200msec.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures data rates to firmware using bitrate mask
provided by cfg80211.
Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211
blocks ibss connection requests if ibss network is already started
/joined. Hence the code to restart ibss network in new channel
(mwifiex_drv_change_adhoc_chan() function) becomes redundant.
2) mwifiex_bss_set_channel() function is redundant. It does some
error checking and calculate adhoc start band and adhoc channel.
Cfg80211 already takes care of error checking and provides correct
channel information to the driver. Adhoc start band is already
calculated in mwifiex_set_rf_channel() function.
Other associated code is also removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass cfg80211_beacon_data pointer instead of cfg80211_ap_settings.
While setting management IEs we only need cfg80211_beacon_data of
cfg80211_ap_settings which has Tail IE, Head IE and other IE elements.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We miss to wakeup main thread after adding command to cmd pending
queue at follwing places. These commands are handled later when
main thread is woken up for handling an interrupt for sleep event
from firmware. This adds worst case delay of 50msec.
1) We don't wakeup main thread when asynchronous command is added
to cmd pending queue. Move queue_work() call from
mwifiex_wait_queue_complete() to mwifiex_send_cmd_async() to wakeup
main thread for sync as well as async commands.
2) Scan operation is triggered due to following reasons
a) request from user (ex. "iw scan" command)
b) Scan performed by driver internally.
In first case main thread is woken up when first scan command is
queued in cmd pending queue (we don't need to wakeup main thread for
subsequent scan commands, because they are queued in scan command
response handler), but it is not done for second case. queue_work()
is moved inside mwifiex_scan_networks() to handle both the cases.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse HT IE from cfg80211 and set HT capabilities accordingly
to FW. If HT IE is missing, 11n would be disabled in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds functionality to set channel info received from
cfg80211_ap_settings in start_ap handler.
Since set_channel cfg80211 handler has been removed and we need
not explicitely call mwifiex_uap_set_channel(); hence this
function definition is also removed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan operation is started when Tx traffic is already running,
driver locks Tx queue until it gets completed. With this logic
there is a delay for Tx packets.
This patch implements new approach to give Tx path higher priority
in this case. Driver internally sends multiple synchronous scan
commands to firmware when scan is requested by user. Now we will
make sure that Tx queue is empty everytime before sending next scan
command. If Tx queue isn't empty scan command will be postponsed by
20msec. This rule will be followed until Tx queue becomes empty or
timeout of 1 second happens. In case of timeout scan operation will
be aborted.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the scan time per channel for active scanning is set to
200ms. It takes quite a while to finsh scanning on all channels,
especially with a dual band configuration.
Change the per channel scan time settings to the following values:
passive scan: 110ms
active scan: 30ms
specific scan: 30ms
Above settings have been tested on x86 and arm platforms.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete custom IEs set by start_ap cfg80211 handler when stop_ap
handler is called for AP interface.
IE index required for deletion is stored in mwifiex_private
structure.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds logic for setting tail beacon IE, probe response IE
and assoc response IE from cfg80211_ap_settings parameter of
start_ap handler into FW.
RSN IE is also retrieved from tail IE buffer and sent to firmware.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. support for setting custom IE from application hostapd etc.
Custom IE addition using auto-indexing and Custom IE deletion using
static indices (which are allocated during IE addition and stored in
driver) are supported.
2. Separate file for handling IE related execution.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Support for parsing security related parameters from
cfg80211_ap_settings in start_ap cfg80211 handler
2. Conversion of these security information into FW understandle TLVs
and setting into FW thru sys_config command
3. key management is done on host. This ensures that FW forwards EAPOL
key packets to host instead of processing on its own.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added logic to handle AP event that are generated
by the firmware. As MLME/SME is implemented in the
firmware, events such as station association and
deauthentication, must be sent to userspace (hostapd)
for creating and deleting station database.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for setting fragmentation threshold, RTS threshold
and retry limit.
Since wiphy parameters are properties of physical device,
appropriate function to set phy parameters is invoked depending
upon bss_type(STA or AP) for each virtual interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. support for AP sys_config command and added parsing of channel
information.
2. support for setting AP channel from cfg80211 set_channel handler
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. separate file for preparing uAP command buffer
2. definition of bss_start and bss_stop commands being sent to
firmware
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify key related cfg80211 handlers to copy peer mac address for
pairwise keys. If peer mac address is not present or group keys,
it will be sent as broadcast mac address.
This would be required since hostapd downloads per peer PTK.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since wiphy structure is per adapter we would save adapter,
instead of mwifiex private pointer, in wiphy_priv.
Also move country_info from mwifiex_private to mwifiex_adapter
as making it part of mwifiex_adapter looks logical.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. wiphy structure is per device; hence moved it to mwifiex_adapter
mwifiex_register_cfg80211 takes mwifiex_adapter as parameter.
This function only registers wiphy with cfg80211.
2. Creation of interfaces is moved to cfg80211 add_virtual_interface
handler.
3. Create 2 interfaces by default: station and AP
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
