Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
- Blackfin ADI pin control driver, we move yet another
architecture under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control
driver. New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things,
this enabled simplified device tree bindings by referring
entire groups of pins on some pin controller to act as
back-end for a certain GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged
through this tree, so the ARC has full support for pins
and GPIOs after this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin
controller instances. The i.MX1 and i.MX27 is an entirely
new family (silicon) of controllers whereas i.MX50 is
a variant of the previous supported controller.
- Then the usual slew of fixes, cleanups and incremental
updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSgHrbAAoJEEEQszewGV1zX/gP/R4mAl5rixzu7RDC0nlUHz2S
F7zf3nhtsAM9GnvJjh9lE43nrisDdCnnBMFeqb7fEr3sp3j+BjQZLp4w/gbkakfY
6xx6dQ+1+fGojd/gqZI9Le6afpBasAz2E8trariOXW5TmET9ai1y9JCmE2l9K3xA
jX3h138iUZ4SihBW7c/Ib46TWfe7vaeAF0WKpfNie/uMHYyc+nXQXNNvtzxtk+N3
+MMuxr9io+d3OyORHD5PlbwWs+jhEPKXfy/isudlkeGbPrA+CMxTCmRc5iu8AvTv
L0wE6FnBhrdbTUHp9fGmdo1sxmIsijYbbc16yVQOn5kAr/hZvmltjV8efBytEep/
268ruds2l3TWypaPotuj8Z3Fxm0Jr/+tcQ9Ck8CTMdrGG3J5D78U8fLwVKTcfzJ5
QjaG0c39MYBbDPO29wfr93MJF7BoNm0D4AyypOCQiH17jL0Q7sXMpeW2WYqlgFf7
uIWnN3Vsh5V4DcYSCrXoHtts1Wn7i8QEkjyj5gQYvXBU47vGToX5xO6Llvr34lVV
VGMhivC3f5Z1UmTImwhi+FkfdDVwBYEuiAo3J9ezGvls4Ywq4AjZV/QZB563CztE
riZ/Xpw3djrxMLKMjGvebTRGpFHcVoh9XV3FetIk+2SCyK7DK1jyYRE1+tvKudAF
TEIV8476kb7xIVbKt8Oy
=z9SM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree. In this case it's involved:
- Some Davinci driver updates that has required corresponding platform code
changes (gpio mostly)
- CCI bindings and a few driver updates
- Marvell mvebu patches for PCI MSI support (could have gone through the PCI
tree for this release, but they were acked by Bjorn for 3.12 so we kept them
through arm-soc).
- Marvell dove switch-over to DT-based PCIe configuration
- Misc updates for Samsung platform dmaengine drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yCsK
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree. In this case it's involved:
- Some Davinci driver updates that has required corresponding
platform code changes (gpio mostly)
- CCI bindings and a few driver updates
- Marvell mvebu patches for PCI MSI support (could have gone through
the PCI tree for this release, but they were acked by Bjorn for
3.12 so we kept them through arm-soc).
- Marvell dove switch-over to DT-based PCIe configuration
- Misc updates for Samsung platform dmaengine drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
ARM: S3C24XX: Fix possible dma selection warning
PCI: mvebu: make local functions static
PCI: mvebu: add I/O access wrappers
PCI: mvebu: Dynamically detect if the PEX link is up to enable hot plug
ARM: mvebu: fix gated clock documentation
ARM: dove: remove legacy pcie and clock init
ARM: dove: switch to DT probed mbus address windows
ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
dmaengine: add driver for Samsung s3c24xx SoCs
ARM: S3C24XX: number the dma clocks
PCI: mvebu: add support for Marvell Dove SoCs
PCI: mvebu: add support for reset on GPIO
PCI: mvebu: remove subsys_initcall
PCI: mvebu: increment nports only for registered ports
PCI: mvebu: move clock enable before register access
PCI: mvebu: add support for MSI
irqchip: armada-370-xp: implement MSI support
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
mxs is a devicetree only platform, so there is no need to check whether we
are in dt or platform data case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pl061 driver has no real dependency on ARM, so remove the kconfig
dependency.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR(). Also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing .owner of struct gpio_chip. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current Kconfig allows GPIO_DEVRES to be selected and compiled without
GPIOLIB. This does not make sense anymore since GPIOLIB has become the
exclusive way to deal with GPIOs. This patch makes GPIO_DEVRES available
only if GPIOLIB is selected.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SA1100 was implementing its own variants of gpio_get_value()
and gpio_set_value() and only selectively falling back to
gpiolib for extended (EGPIO) handling. However the driver in
gpio/gpio-sa1100.c already handles the same functionality for
these lines, yet remain unused.
The only upside would be things like a timing-critical hotpath
on bit-banged GPIO, but that kind of things does not seem to
happen on these GPIOs, so it is not worth having the extra
complexity.
Tested with some buttons on the Compaq iPAQ H3630.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jVqg
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
Samsung Cleanup for v3.13
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
s3c-camif: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
gpio: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
ARM: S3C64XX: Move if ARCH_S3C64XX statement into mach-s3c64xx
Signed-off-by: Olof Johansson <olof@lixom.net>
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the return value if devm_gpiod_get_index(). It was returning 0 while
it should return the obtained GPIO descriptor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACPI GpioInt resources contain polarity field that is used to specify
whether the interrupt is active high or low. Since gpiolib supports
GPIOF_ACTIVE_LOW we can pass this information in the flags field in
acpi_find_gpio(), analogous to the DeviceTree version.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_get_index() and gpiod_get() are now the new preferred way to request
GPIOs. Add support for finding the corresponding GPIO descriptor from ACPI
namespace.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new GPIO descriptor based interface is now preferred over the old
integer based one. This patch converts the ACPI GPIO helpers to use this
new interface internally. In addition to that provide compatibility
function acpi_get_gpio_by_index() that converts the returned GPIO
descriptor to an integer.
We also drop acpi_get_gpio() as it is not used anywhere outside
gpiolib-acpi and even there we use acpi_get_gpiod() instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add gpiod_get(), gpiod_get_index() and gpiod_put() functions that
provide safer management of GPIOs.
These functions put the GPIO framework in line with the conventions of
other frameworks in the kernel, and help ensure every GPIO is declared
properly and valid while it is used.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Refactor the of_ functions of gpiolib to use the now public gpiod
interface, and export of_get_named_gpiod_flags() and
of_get_gpiod_flags() functions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch exports the gpiod_* family of API functions, a safer
alternative to the legacy GPIO interface. Differences between the gpiod
and legacy gpio APIs are:
- gpio works with integers, whereas gpiod operates on opaque handlers
which cannot be forged or used before proper acquisition
- gpiod get/set functions are aware of the active low state of a GPIO
- gpio consumers should now include <linux/gpio/consumer.h> to access
the new interface, whereas chips drivers will use
<linux/gpio/driver.h>
The legacy gpio API is now built as inline functions on top of gpiod.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The physical address of the GPIO memory address is already printed
implicitly by dev_info() as part of the device name. The virtual
address doesn't add any value. In addition, printing a resource_size_t
with %x lead to a compiler warning on some platforms.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whenever an IRQ is claimed or freed, call gpio_lock_as_irq() or
gpio_unlock_as_irq() on the associated GPIO, to prevent that GPIO from
being configured in a manner incompatible with an interrupt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the infrastructure required to register non-linear gpio
ranges through gpiolib and the standard GPIO device tree bindings.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OMAP GPIO driver keeps track about GPIO pins that are
used as IRQ lines for two reasons:
1) To prevent GPIO banks to be disabled while one of their
GPIO pins are only used as an interrupt line.
2) To not allow another caller to set the GPIO pin as output.
Now gpiolib has an API to mark GPIO pins as used as IRQ lines
so the GPIO core only allows to set as output GPIO pins not
tied to an IRQ. So there is no need to have custom code for 2).
The IRQ usage still has to be maintained locally for 1) though.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is currently often possible in many GPIO drivers to request
a GPIO line to be used as IRQ after calling gpio_to_irq() and,
as the gpiolib is not aware of this, set the same line to
output and start driving it, with undesired side effects.
As it is a bogus usage scenario to request a line flagged as
output to used as IRQ, we introduce APIs to let gpiolib track
the use of a line as IRQ, and also set this flag from the
userspace ABI.
The API is symmetric so that lines can also be flagged from
.irq_enable() and unflagged from IRQ by .irq_disable().
The debugfs file is altered so that we see if a line is
reserved for IRQ.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I have no idea why this driver is using __raw* accessors for
reading and writing registers, I suspect it is just force of
habit or copy/paste. Change all to readb()/writeb() except
one chain where I used writeb_relaxed() up until the last
writeb().
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
When doing this I see that the hwirq argument is used
for mapping rather than the Linux IRQ in the map function.
This doesn't look right. Use the Linux IRQ instead.
I cannot test this patch so I don't know if the mapping change
is correct, however since absolutely every other driver does
it the other way around this doesn't look sound at all. Please
help out with review.
Cc: Vipul Kumar Samar <vipulkumar.samar@st.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Gabriel Fernandez <gabriel.fernandez@st.com>
Cc: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus. Take this
opportunity to sink a variable into a loop.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Cc: Magnus Damm <damm@opensource.se>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus. Rename the
"gpio" variable to "hwirq" to reflect what it is. Rename one
instance of "virq" to "child_irq" that better describes what
it is.
Cc: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is confusingly named, the different Linux IRQs
aren't any more virtual than any other Linux IRQ. Give it a
non-misleading name.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bqsS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO interrupt handler does not need to be marked as nested.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Patch be1a4b brought some improvements to the GPIO error handling code,
but also changed the return value of gpiod_request() when called on a
not yet initialized GPIO descriptor: it now returns -EINVAL instead of
-EPROBE_DEFER, and this affects some drivers.
This patch restores the original behavior for gpiod_request(). It is
safe to do so now that desc_to_gpio() does not rely on the GPIO
descriptor to be initialized. Other functions changed by patch be1a4b
do not see their return value affected, so these are not reverted.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Dr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current implementation of desc_to_gpio() relies on the chip pointer
to be set to a valid value in order to compute the GPIO number. This
was done in the hope that we can get rid of the gpio_desc global array,
but this is not happening anytime soon.
This patch reimplements desc_to_gpio() in a fashion similar to that of
gpio_to_desc(). As a result, desc_to_gpio(gpio_to_desc(gpio)) == gpio is
now always true. This allows to call desc_to_gpio() on non-initialized
descriptors as some error-handling code currently does.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Dr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After file was renamed from gpio-langwell to gpio-intel-mid, this patch
updates the variables, functions and structs to be based on intel-mid
instead of langwell.
There is no function change.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio-langwell is a deprecated name. Despite the driver was made
initially for Langwell, it supports now other Intel Mid SoC's.
This patch does no change beside the file renaming with Kconfig/Makefile
update.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch implements a better way to handle multiple SoC's and adds
Intel Merrifield support to gpio-langwell.
It was based on previous work from Ning Li <ning.li@intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Ning Li <ning.li@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Checking LP_INT_STAT is not enough in the interrupt handler because its
contents get updated regardless of whether the pin has interrupt enabled or
not. This causes the driver to loop forever for GPIOs that are pulled up.
Fix this by checking the interrupt enable bit for the pin as well.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It makes more sense to have these functions close to each other. No
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Since CONFIG_PLAT_S3C64XX is going to be removed, this patch modifies
the gpio-samsung driver to use the proper way of checking for S3C64xx
support - CONFIG_ARCH_S3C64XX.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Two patches for the OMAP driver, dealing with setting up IRQs
properly on the device tree boot path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ALq3
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
We need to use the of_node from the main Arizona device as that
holds our configuration.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OMAP GPIO controller HW requires a pin to be configured in GPIO
input mode in order to operate as an interrupt input. Since drivers
should not be aware of whether an interrupt pin is also a GPIO or not,
the HW should be fully configured/enabled as an IRQ if a driver solely
uses IRQ APIs such as request_irq(), and never calls any GPIO-related
APIs. As such, add the missing HW setup to the OMAP GPIO controller's
irq_chip driver.
Since this bypasses the GPIO subsystem we have to ensure that another
driver won't be able to request the same GPIO pin that is used as an
IRQ and set its direction as output. Requesting the GPIO and setting
its direction as input is allowed though.
This fixes smsc911x ethernet support for tobi and igep OMAP3 boards
and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO OMAP controller pins can be used as IRQ and GPIO
independently so is necessary to keep track GPIO pins and
IRQ lines usage separately to make sure that the bank will
always be enabled while being used.
Also move gpio_is_input() definition in preparation for the
next patch that setups the controller's irq_chip driver when
a caller requests an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pre-existing sysfs interfaces which take explicit namespace
argument are weird in that they place the optional @ns in front of
@name which is contrary to the established convention. For example,
we end up forcing vast majority of sysfs_get_dirent() users to do
sysfs_get_dirent(parent, NULL, name), which is silly and error-prone
especially as @ns and @name may be interchanged without causing
compilation warning.
This renames sysfs_get_dirent() to sysfs_get_dirent_ns() and swap the
positions of @name and @ns, and sysfs_get_dirent() is now a wrapper
around sysfs_get_dirent_ns(). This makes confusions a lot less
likely.
There are other interfaces which take @ns before @name. They'll be
updated by following patches.
This patch doesn't introduce any functional changes.
v2: EXPORT_SYMBOL_GPL() wasn't updated leading to undefined symbol
error on module builds. Reported by build test robot. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove NEED_MACH_GPIO_H config select option for ARCH_DAVINCI
to start using gpiolib interface for davinci platforms. This makes
it easier to use the gpio driver on other platforms as it breaks
dependency on mach-davinci.
Latencies for gpio_get/set APIs will increase. On measurement,
latency was found to have increased by 18 microsecond with
gpiolib API as compared to inline APIs.
Measurement was done on DA850 EVM for gpio_get_value() API by
taking the printk timing across the call with interrupts disabled.
inline gpio API with interrupt disabled
[ 29.734337] before gpio_get
[ 29.736847] after gpio_get
Time difference 0.00251
gpio library with interrupt disabled
[ 272.876763] before gpio_get
[ 272.879291] after gpio_get
Time difference 0.002528
Latency increased by (0.002528 - 0.00251) = 18 microsecond.
While at it, remove GPIO_TYPE_DAVINCI enum definition as
gpio-davinci.c is converted to Linux device driver model.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nsekhar@ti.com: minor edits to commit message]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Modify DaVinci GPIO driver to become a platform device
driver.
The driver does not have platform driver structure or
a probe. Instead, it has pure_initcall function for
initialization. The platform specific informaiton is
obtained using the DaVinci specific davinci_soc_info
structure. This is a problem for Device Tree (DT)
implementation.
As a first stage of DT conversion, we implement a probe.
Additional notes:
- The driver registration happens as postcore_initcall.
This is required since machine init functions like
da850_lcd_hw_init() make use of GPIO.
- Start using devres APIs for simpler error handling.
Signed-off-by: KV Sujith <sujithkv@ti.com>
[avinashphilip@ti.com: Move global definition of
"davinci_gpio_controller" to local]
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nsekhar@ti.com: drop unused structure member, rebase to new
clean-up patch and fix error messages]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Make some minor coding style fixes. Use proper multi-line
commenting style, and use a macro for register offset.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[nsekhar@ti.com: drop changes which are considered
unnecessary churn - line break fixes
variable name changes and include file
reordering]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add DT bindings for the pcf857x-compatible chips and parse the device
tree node in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pca957x driver supports a handful of I2C GPIO expanders from NXP, Maxim,
and TI. For the PCA9574 and PCA9575 devices only, the driver resets the GPIO
level and direction in the pca957x_probe function. This seems like the wrong
thing to do, since it can cause hardware bit twiddles during warm reboots when
the chip state and reset values don't match.
This kind of initialization is best left upstream (in a bootloader) or
downstream (in userspace). It's also an inconsistency across devices supported
by this driver.
This patch is NOT boot-tested: the SoC I'm using is stuck on 2.6.37, and the
patch doesn't apply trivially.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'gen_74x164_dt_ids' is always compiled in. Hence the macro is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a1bc260bb5 ("gpio: clean up
gpio-ranges documentation") deprecated the #gpio-range-cells property.
Replace its usage with a hardcoded value in the gpio-rcar driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per the pattern from other GPIO drivers, use set_irq_flags()
on ARM only, use irq_set_noprobe() on other archs.
Also rename the argument "virq" to just "irq", this IRQ isn't
any more "virtual" than any other Linux IRQ number, we use
"hwirq" for the actual hw-numbers, "virq" is just bogus.
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This alters the IOP platforms to pass a physical base for their
GPIO blocks and alters the driver to remap it when probing
instead of relying on the virtual addresses to be used.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the standard 32bit I/O accessors instead of just assigning
addresses.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the IOP32x and IOP33x platforms to pass their
base address offset by a resource attached to a platform device
instead of using static offset macros implicitly passed
through <linux/gpio.h> including <mach/gpio.h>. Delete the
local <mach/gpio.h> and <asm/hardware/iop3xx-gpio.h> headers
and remove the selection of NEED_MACH_GPIO_H.
Pass the virtual address as a resource in the platform device
at this point for bisectability, next patch will pass the
physical address as is custom.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kernel will now only use gpiolib to access GPIOs, so remove
the complex GPIO flag and the custom implementation.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes the only dependence between the IOP GPIO
driver and the GENERIC_GPIO header in <mach/gpio.h>
and its common implementation in the <asm/*> namespace
by copying the one constant it is using into the driver
file.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the IOP GPIO driver to live with its siblings in the
GPIO subsystem.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the recent code cleanup from Marek Vasut, driver gpio-ucb1400 can
be built as a module, so change symbol GPIO_UCB1400 from bool to
tristate.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the GPIO driver for the Broadcom bcm281xx family of mobile SoCs.
These GPIO controllers may contain up to 8 banks where each bank
includes 32 pins that can be driven high or low and act as an edge
sensitive interrupt.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[Added depends on OF_GPIO]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_get/set functions share common code between their regular and
cansleep variants. The exporting of the gpiod interface will make
the situation worse. This patch factorizes the common code to avoid code
redundancy.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EMEV2 is now a DT platform, however the GPIO driver cannot be used
from a DT file since it does not fill out the of_node field in its
gpio_chip structure.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TI Palmas series device TPS80036 supports 16 GPIOs.
Register its all 16 gpios when this device is selected.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide the human readable label for the GPIO as well as the number when
we are recording it in order to improve the readability of log messages.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently many but not all GPIO log messages log the GPIO number and the
formats vary. Ensure that this is done consistently by defining logging
helpers which take the GPIO descriptor.
The will help people pattern matching on logs and providing the number
makes the log messages that omitted it more useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per the pattern from other GPIO drivers, use set_irq_flags()
on ARM only, use irq_set_noprobe() on other archs.
Also rename the argument "virq" to just "irq", this IRQ isn't
any more "virtual" than any other Linux IRQ number, we use
"hwirq" for the actual hw-numbers, "virq" is just bogus.
Cc: George Cherian <george.cherian@ti.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_execute_simple_method() is a new ACPI API introduced to invoke
an ACPI control method that has single integer parameter and no return value.
Convert acpi_evaluate_object() to acpi_execute_simple_method()
in drivers/gpio/gpiolib-acpi.c
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For pcf857x driver if the initial state is not set properly (proper
n_latch is not passed), we get bad irq prints on console.
We get this only for the first interrupt and doesnot repeat for further
interrupts unles and until there are other gpio pins which are not flipping
continously.
following prints are seen on console.
[ 40.983924] irq 0, desc: ce004080, depth: 1, count: 0, unhandled: 0
[ 40.990511] ->handle_irq(): c00aa538, handle_bad_irq+0x0/0x260
[ 40.996768] ->irq_data.chip(): c080b6ec, no_irq_chip+0x0/0x60
[ 41.002842] ->action(): (null)
[ 41.006242] IRQ_NOPROBE set
[ 41.009465] IRQ_NOREQUEST set
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we are using devm_request_threaded_irq no need for
irq_demux_work and gpio->irq. Remove all its references.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the request_irq and use devm_request_threaded_irq
also cleanup free_irq. devm_* takes care of that.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since this driver does not handle GPIO on device tree enabled platforms
any more, it should be bypassed whenever device tree is available, to
not conflict with the new pinctrl-samsung driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
Generally minor changes. A bunch of bug fixes, particularly for
initialization and some refactoring. Most notable change if feeding the
entire flattened tree into the random pool at boot. May not be
significant, but shouldn't hurt either.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GSWl
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree core updates from Grant Likely:
"Generally minor changes. A bunch of bug fixes, particularly for
initialization and some refactoring. Most notable change if feeding
the entire flattened tree into the random pool at boot. May not be
significant, but shouldn't hurt either"
Tim Bird questions whether the boot time cost of the random feeding may
be noticeable. And "add_device_randomness()" is definitely not some
speed deamon of a function.
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/platform: add error reporting to of_amba_device_create()
irq/of: Fix comment typo for irq_of_parse_and_map
of: Feed entire flattened device tree into the random pool
of/fdt: Clean up casting in unflattening path
of/fdt: Remove duplicate memory clearing on FDT unflattening
gpio: implement gpio-ranges binding document fix
of: call __of_parse_phandle_with_args from of_parse_phandle
of: introduce of_parse_phandle_with_fixed_args
of: move of_parse_phandle()
of: move documentation of of_parse_phandle_with_args
of: Fix missing memory initialization on FDT unflattening
of: consolidate definition of early_init_dt_alloc_memory_arch()
of: Make of_get_phy_mode() return int i.s.o. const int
include: dt-binding: input: create a DT header defining key codes.
of/platform: Staticize of_platform_device_create_pdata()
of: Specify initrd location using 64-bit
dt: Typo fix
OF: make of_property_for_each_{u32|string}() use parameters if OF is not enabled
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block.
This is found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on
some x86 boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the
modernized pin control driver to provide GPIO for the
modern platforms instead.
- The usual bunch of non-critical fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=oEK9
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.12 series:
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block. This is
found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on some x86
boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the modernized pin
control driver to provide GPIO for the modern platforms instead.
- The usual bunch of non-critical fixes and cleanups"
* tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (36 commits)
gpio: return -ENOTSUPP if debounce cannot be set
gpio: improve error path in gpiolib
gpio: add GPIO support for F71882FG and F71889F
of: add vendor prefix for Microchip Technology Inc
gpio: mcp23s08: rename the device tree property
gpio: samsung: Drop support for Exynos SoCs
gpio: pcf857x: Remove pdata argument to pcf857x_irq_domain_init()
gpio: pcf857x: Sort headers alphabetically
gpio: max7301: Reverting "Do not force SPI speed when using OF Platform"
gpio: Fix bit masking in Kontron PLD GPIO driver
gpio: pca953x: fix gpio input on gpio offsets >= 8
drivers/gpio: simplify use of devm_ioremap_resource
drivers/gpio/gpio-omap.c: convert comma to semicolon
gpio-lynxpoint: Fix warning about unbalanced pm_runtime_enable
gpio: Fix platform driver name in Kontron PLD GPIO driver
gpio: adnp: Fix segfault if request_threaded_irq fails
gpio: msm: Staticize local variable 'msm_gpio'
gpio: gpiolib-of.c: make error message more meaningful by adding the node name and index
gpio: use dev_get_platdata()
gpio/mxc: add chained_irq_enter/exit() to mx2_gpio_irq_handler
...
It appears some drivers are using gpio_set_debounce()
opportunistically, i.e. without knowing whether it works or
not. (Example: input/keyboard/gpio_keys.c) to account for
this use case, return -ENOTSUPP and do not print any
warnings in this case.
Took a round over the other gpio_set_debounce() consumers
to make sure that none of them are relying on the returned
error code to be something specific.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At several places the gpiolib will proceed to handle a GPIO
descriptor even if it's ->chip member is NULL and no gpiochip
is associated.
Fix this by checking that both the descriptor cookie *and*
the chip pointer are valid.
Also bail out earlier with more specific diagnostic messages
on missing operations for setting as input/output or debounce.
ChangeLog v1->v2:
- Also return -EIO on gpiod_set_debounce() with missing
operations in the vtable
- Fix indentations.
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the GPIOs found on the Fintek super-I/O
chips F71882FG and F71889F.
A super-I/O is a legacy I/O controller embedded on x86 motherboards. It
is used to connect the low-bandwidth devices. Among others functions the
F71882FG/F71889F provides: a parallel port, two serial ports, a keyboard
controller, an hardware monitoring controller and some GPIO pins.
Note that this super-I/Os are embedded on some Atom-based LaCie NASes.
The GPIOs are used to control the LEDs and the hard drive power.
Changes since v3:
- Use request_muxed_region to protect the I/O ports against concurrent
accesses.
Changes since v2:
- Remove useless NULL setters for driver data.
Changes since v1:
- Enhance the commit message by describing what is a Super-I/O.
- Use self-explanatory names for the GPIO register macros.
- Add a comment to explain the platform device and driver registration.
- Fix gpio_get when GPIO is configured in input mode. I only had
the hardware to check this mode recently...
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device tree property should be more descriptive.
microchip seems more reasonable than mcp. The old mcp
prefix is still supported but marked as deprecated.
Users of mcp have to switch to the microchip prefix.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new of_parse_phandle_with_fixed_args() to implement the
corrected gpio-ranges DT property definition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch moves the pca953x.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
GPIO support on Exynos SoCs is provided by pinctrl-samsung driver,
leaving all the support code in gpio-samsung driver unused. This dead
code can be safely removed and so it is done by this patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SOCs in the OCTEON family have 16 (or in some cases 20) on-chip
GPIO pins, this driver handles them all. Configuring the pins as
interrupt sources is handled elsewhere (OCTEON's irq handling code).
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5633/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The argument is not used, remove it. No board registers a pcf857x device
with an IRQ without specifying platform data, IRQ domain registration
behaviour is thus not affected by this change.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes checking for duplicates when adding a new #include easier.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch reverts commit 047b93a359 which breaks
MAX7301 GPIO driver because that commit was dependant on a rejected patch that
was implementing selection of SPI speed from the Device Tree.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the bit masking within the GPIO driver. The masking is
basically done twice which causes the wrong GPIOs to be addressed.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change fixes a regression introduced by commit
f5f0b7aa8 (gpio: pca953x: make the register access by GPIO bank)
When the pca953x driver was converted to using 8-bit reads/writes
the bitmask in pca953x_gpio_get_value wasn't adjusted with a
modulus BANK_SZ and consequently looks at the wrong bits in the
input register.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace a comma between expression statements by a semicolon. This changes
the semantics of the code, but given the current indentation appears to be
what is intended.
A simplified version of the semantic patch that performs this
transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch changes the driver name to be consistent with the name that
is registered as cell name in the MFD driver. Otherwise the driver won't
load.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kevin Strasser <strassek@engr.orst.edu>
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
In case request_threaded_irq inside adnp_irq_setup fails, the driver
segfaults. This is because irq_domain_remove is called twice with
the same pointer. First time in adnp_irq_setup and then a second time
after leaving adnp_irq_setup in the error path of adnp_i2c_probe
inside adnp_teardown.
This fixes this by removing the call to irq_domain_remove from
adnp_irq_setup.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local variable 'msm_gpio' is used only in this file.
Fix the following sparse warning:
drivers/gpio/gpio-msm-v2.c:109:21: warning: symbol 'msm_gpio' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Similar to commit
0e44b6e (gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler())
. It doesn't seem to be critical to make the irqs work, but still it is
more correct.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to gpiochip_add made by this driver is capable of auto-selecting a
base if one is not provided. However, it was not called unless there was
already a DT entry or platform data. This patch calls it even if the base is
not already known so that gpiochip_add can attempt to find a usable base.
Signed-off-by: Daniel M. Weeks <dan@danweeks.net>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems that the value read back from the PALMAS_GPIO_DATA_IN register
isn't valid if the GPIO direction is out. When that's the case, we can
read back the PALMAS_GPIO_DATA_OUT register to get the proper output value.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/gpio/gpio-msm-v1.c: In function 'gpio_msm_v1_probe':
drivers/gpio/gpio-msm-v1.c:656:2:
error: implicit declaration of function 'IS_ERR'
[-Werror=implicit-function-declaration]
drivers/gpio/gpio-msm-v1.c:657:3:
error: implicit declaration of function 'PTR_ERR'
[-Werror=implicit-function-declaration]
This driver failed to compile after commit 68515bb
(gpio_msm: Convert to use devm_ioremap_resource,
2013-06-10).
Acked-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 8cd73e4e (gpio: gpio-mxc: Use devm functions) causes the following build
error on imx_v4_v7_defconfig:
drivers/gpio/gpio-mxc.c:414:2: error: implicit declaration of function 'IS_ERR' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-mxc.c:415:3: error: implicit declaration of function 'PTR_ERR' [-Werror=implicit-function-declaration]
Note: imx_v6_v7_defconfig does not give this build error, probably due to some
indirect header file inclusion.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit f87311743 ("ARM: mmp: add more compatible names in gpio driver")
changed the driver logic to determine the number of available GPIOs from
the compatible string, and hence obsoleted the (undocumented) child
nodes that were previously necessary. However, it left some remainder
which can be safely removed now.
Also, this patch makes pxa_gpio_probe_dt() return the correct value in
case irq_alloc_descs() fails.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Register the GPIO pin range, and request and free GPIO pins using the
pinctrl API. The pctl_name platform data member should be used by
platform devices to point out which pinctrl device to use.
Follows same style as "dc3465a gpio-rcar: Add pinctrl support",
by Laurent Pinchart, thanks to him.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add gpio support for the on-board PLD found on some Kontron embedded modules.
Originally-from: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_property_read_u32 return 0 on success. The check was using a ! to
return error. Fix the if condition.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Pankaj Jangra <jangra.pankaj9@gmail.com>
Cc: "Bird, Tim" <Tim.Bird@sonymobile.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TWL6040 is used only with OMAP4/5 SoCs and they can only boot in in DT mode.
The support for pdata/legacy boot can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By using devm functions we can get a simpler code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert gpio-tz1090 driver to use generic irqchips. This allows the
irq_ack, irq_mask, and irq_unmask callbacks and associated helper
functions to be removed. Also switch to using irq_setup_alt_chip() in
the irq_set_type callback instead of using __irq_set_handler_locked().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.
The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
Changes in v2:
- gpio-tz1090-pdc: remove references to Linux flags in dt bindings
- gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
- gpio-tz1090-pdc: make register accessors inline to match pinctrl
- gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC.
This doesn't include low-power GPIOs as they're controlled separately
via the Powerdown Controller (PDC) registers.
The driver is instantiated by device tree and supports interrupts for
all GPIOs.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
- gpio-tz1090: use of_property_read_u32 instead of of_get_property
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- some s/unsigned int/bool/ and use of BIT().
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
- gpio-tz1090: add REG_ prefix to some constants for consistency.
- gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge
cunningness.
Changes in v2:
- gpio-tz1090: remove references to Linux flags in dt bindings
- gpio-tz1090: make use of BIT() from linux/bitops.h
- gpio-tz1090: make register accessors inline to match pinctrl
- gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OMAP GPIO driver check if the chip has an associated
Device Tree node using the struct gpio_chip of_node member.
But this is only build if CONFIG_OF_GPIO is defined which
leads to the following error when using omap1_defconfig:
linux/drivers/gpio/gpio-omap.c: In function 'omap_gpio_chip_init':
linux/drivers/gpio/gpio-omap.c:1080:17: error: 'struct gpio_chip' has no member named 'of_node'
linux/drivers/gpio/gpio-omap.c: In function 'omap_gpio_irq_map':
linux/drivers/gpio/gpio-omap.c:1116:16: error: 'struct gpio_chip' has no member named 'of_node'
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an OMAP GPIO is used as an IRQ line, a call to gpio_request()
has to be made to initialize the OMAP GPIO bank before a driver
request the IRQ. Otherwise the call to request_irq() fails.
Drives should not be aware of this neither care wether an IRQ line
is a GPIO or not. They should just request the IRQ and this has to
be handled by the irq_chip driver.
With the current OMAP GPIO DT binding, if we define:
gpio6: gpio@49058000 {
compatible = "ti,omap3-gpio";
reg = <0x49058000 0x200>;
interrupts = <34>;
ti,hwmods = "gpio6";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
interrupt-parent = <&gpio6>;
interrupts = <16 8>;
The GPIO is correctly mapped as an IRQ but a call to gpio_request()
is never made. Since a call to the custom IRQ domain .map function
handler is made for each GPIO used as an IRQ, the GPIO can be setup
and configured as input there automatically.
Changes since v3:
- Use bank->chip.of_node instead of_have_populated_dt() to check
DT or legacy boot as suggested by Jean-Christophe PLAGNIOL-VILLARD
- Add a comment that this is just a temporary solution until and
that it has to be removed once is handled by the IRQ core.
Changes since v2:
- Only make the call to gpio_request_one() conditional in the DT
case as suggested by Grant Likely.
Changes since v1:
- Split the irq domain mapping function handler and the GPIO
request in two different patches.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO is defined as an interrupt line using Device
Tree, a call to irq_create_of_mapping() is made that calls
irq_create_mapping(). So, is not necessary to do the mapping
for all OMAP GPIO lines and explicitly call irq_create_mapping()
on the driver probe() when booting with Device Tree.
Add a custom IRQ domain .map function handler that will be
called by irq_create_mapping() to map the GPIO lines used as IRQ.
This also allows to execute needed setup code such as configuring
a GPIO as input and enabling the GPIO bank.
Changes since v3:
- Use bank->chip.of_node instead of_have_populated_dt() to check
DT or legacy boot as suggested by Jean-Christophe PLAGNIOL-VILLARD
Changes since v2:
- Unconditionally do the IRQ setup in the .map() function and
only call irq_create_mapping() in the gpio chip init to avoid
code duplication as suggested by Grant Likely.
Changes since v1:
- Split the addition of the .map function handler and the
automatic gpio request in two different patches.
- Add GPIO IRQ setup logic to the irq domain mapping function.
- Only call irq_create_mapping for every GPIO on legacy boot.
- Only setup a GPIO IRQ on the .map function for DeviceTree boot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
- Incremental development for the Langwell (Atom SoC),
Xilinx, ICH and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun,
Wolfram Sang, Tushar Behera, Sachin Kamat and Yijing Wang.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=5JfC
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is a batch of GPIO changes for v3.11. I have agreed with Grant
to take care of the pull requests for this development cycle.
No special things are happening in the GPIO tree this time (nice with
some calm) and I have been extra careful to do regression builds and
it's well boiled in -next.
GPIO changes for the v3.11 development cycle:
- Incremental development for the Langwell (Atom SoC), Xilinx, ICH
and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun, Wolfram Sang,
Tushar Behera, Sachin Kamat and Yijing Wang"
* tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (35 commits)
Gpio/trivial: replace numeric with standard PM state macros
gpiolib: remove warnning of allocations with IRQs disabled
gpio: grgpio: Staticize local symbols
gpio-langwell: remove Withney point support
gpio: ich: add GPO_BLINK support
gpio-sta2x11: Convert to use devm_ioremap_resource
gpio_msm: Convert to use devm_ioremap_resource
gpio-rcar: Use OUTDT when reading GPIOs configured as output
gpio-sta2x11: Fix potential NULL pointer dereference
gpio/omap: omap_gpio_init_context stub must be inline
gpio: msm-v1: Remove errant __devinit to fix compile
gpio: devres: make comments proper
GPIO: xilinx: Enable driver for Xilinx zynq
DT: Add documentation for gpio-xilinx
GPIO: xilinx: Use BIT macro
GPIO: xilinx: Use __raw_readl/__raw_writel IO functions
GPIO: xilinx: Add support for dual channel
GPIO: xilinx: Simplify driver probe function
gpio: sx150x: convert to use devm_* functions
MAINTAINERS: add linux-gpio mailing list
...
Pull core irq changes from Ingo Molnar:
"The main changes:
- generic-irqchip driver additions, cleanups and fixes
- 3 new irqchip drivers: ARMv7-M NVIC, TB10x and Marvell Orion SoCs
- irq_get_trigger_type() simplification and cross-arch cleanup
- various cleanups, simplifications
- documentation updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
softirq: Use _RET_IP_
genirq: Add the generic chip to the genirq docbook
genirq: generic-chip: Export some irq_gc_ functions
genirq: Fix can_request_irq() for IRQs without an action
irqchip: exynos-combiner: Staticize combiner_init
irqchip: Add support for ARMv7-M NVIC
irqchip: Add TB10x interrupt controller driver
irqdomain: Use irq_get_trigger_type() to get IRQ flags
MIPS: octeon: Use irq_get_trigger_type() to get IRQ flags
arm: orion: Use irq_get_trigger_type() to get IRQ flags
mfd: stmpe: use irq_get_trigger_type() to get IRQ flags
mfd: twl4030-irq: Use irq_get_trigger_type() to get IRQ flags
gpio: mvebu: Use irq_get_trigger_type() to get IRQ flags
genirq: Add irq_get_trigger_type() to get IRQ flags
genirq: Irqchip: document gcflags arg of irq_alloc_domain_generic_chips
genirq: Set irq thread to RT priority on creation
irqchip: Add support for Marvell Orion SoCs
genirq: Add kerneldoc for irq_disable.
genirq: irqchip: Add mask to block out invalid irqs
genirq: Generic chip: Add linear irq domain support
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
