The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5QjC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some platforms don't have DMA, but we should still be able to build USB
drivers for these platforms. They could still be used through vhci_hcd,
usbip_host, or maybe something like USB passthrough in UML from a
capable host.
If NO_DMA=y:
ERROR: "dma_pool_destroy" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/core/usbcore.ko] undefined!
Add a few checks for CONFIG_HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The US_DEBUGPX macro uses printk without specifying a kernel log level, so
the default kernel log level is used, which may not match LOGLEVEL_DEBUG
used in usb_stor_dbg. Remove the macro and use usb_store_dbg instead.
Signed-off-by: Victor Dodon <printesoi@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device is disconnected poll waiters were not being woken.
Changes for v2:
- add commit summary
- add Fixes and Reported-by tags
Fixes: eb6b92ecc0 ("Add support for receiving USBTMC USB488 SRQ notifications via poll/select")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write value is 8bit, but currently writing a larger number (eg a doubled
digit) is not errored but instead gets cast and sets off an action probably
undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow for and clean handling of signals an URB is introduced.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shares the cleanup code between all probe failure paths, instead of
having per-failure cleanup at each point in the function.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4b61b4f205.
As reported by Oliver, this change was unnecessary.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d8f00cd685.
Tony writes:
This upstream commit is causing an oops:
d8f00cd685 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eFQw
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc5
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)
Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use regmap to access the PMC to avoid using at91_pmc_read and
at91_pmc_write.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix spelling typos found in printk and Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new interface for userspace to preallocate memory that can be
used with usbfs. This gives two primary benefits:
- Zerocopy; data no longer needs to be copied between the userspace
and the kernel, but can instead be read directly by the driver from
userspace's buffers. This works for all kinds of transfers (even if
nonsensical for control and interrupt transfers); isochronous also
no longer need to memset() the buffer to zero to avoid leaking kernel data.
- Once the buffers are allocated, USB transfers can no longer fail due to
memory fragmentation; previously, long-running programs could run into
problems finding a large enough contiguous memory chunk, especially on
embedded systems or at high rates.
Memory is allocated by using mmap() against the usbfs file descriptor,
and similarly deallocated by munmap(). Once memory has been allocated,
using it as pointers to a bulk or isochronous operation means you will
automatically get zerocopy behavior. Note that this also means you cannot
modify outgoing data until the transfer is complete. The same holds for
data on the same cache lines as incoming data; DMA modifying them at the
same time could lead to your changes being overwritten.
There's a new capability USBDEVFS_CAP_MMAP that userspace can query to see
if the running kernel supports this functionality, if just trying mmap() is
not acceptable.
Largely based on a patch by Markus Rechberger with some updates. The original
patch can be found at:
http://sundtek.de/support/devio_mmap_v0.4.diff
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/built-in.o: In function `ehci_platform_probe':
/home/vegard/linux/drivers/usb/host/ehci-platform.c:282: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `oxu_drv_probe':
/home/vegard/linux/drivers/usb/host/oxu210hp-hcd.c:3821: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `isp1362_probe':
/home/vegard/linux/drivers/usb/host/isp1362-hcd.c:2668: undefined reference to `devm_ioremap_resource'
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/host/xhci-mtk.o
drivers/usb/host/xhci-mtk.c:135:12: warning: ‘xhci_mtk_host_disable’ defined but not used [-Wunused-function]
static int xhci_mtk_host_disable(struct xhci_hcd_mtk *mtk)
^
drivers/usb/host/xhci-mtk.c:313:13: warning: ‘usb_wakeup_enable’ defined but not used [-Wunused-function]
static void usb_wakeup_enable(struct xhci_hcd_mtk *mtk)
^
drivers/usb/host/xhci-mtk.c:321:13: warning: ‘usb_wakeup_disable’ defined but not used [-Wunused-function]
static void usb_wakeup_disable(struct xhci_hcd_mtk *mtk)
^
CC drivers/usb/host/sl811-hcd.o
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_remove’:
drivers/usb/host/sl811-hcd.c:1607:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sl811->data_reg);
^
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_probe’:
drivers/usb/host/sl811-hcd.c:1669:3: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
addr_reg = ioremap(addr->start, 1);
^
drivers/usb/host/sl811-hcd.c:1669:12: warning: assignment makes pointer from integer without a cast [enabled by default]
addr_reg = ioremap(addr->start, 1);
^
drivers/usb/host/sl811-hcd.c:1675:12: warning: assignment makes pointer from integer without a cast [enabled by default]
data_reg = ioremap(data->start, 1);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/c67x00/c67x00-drv.o
drivers/usb/c67x00/c67x00-drv.c: In function ‘c67x00_drv_probe’:
drivers/usb/c67x00/c67x00-drv.c:148:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
c67x00->hpi.base = ioremap(res->start, resource_size(res));
^
drivers/usb/c67x00/c67x00-drv.c:148:19: warning: assignment makes pointer from integer without a cast [enabled by default]
c67x00->hpi.base = ioremap(res->start, resource_size(res));
^
drivers/usb/c67x00/c67x00-drv.c:185:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(c67x00->hpi.base);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/musb/tusb6010.o
drivers/usb/musb/tusb6010.c: In function ‘tusb_musb_init’:
drivers/usb/musb/tusb6010.c:1133:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1133:7: warning: assignment makes pointer from integer without a cast [enabled by default]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1162:4: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sync);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC drivers/usb/host/r8a66597-hcd.o
drivers/usb/host/r8a66597-hcd.c: In function ‘r8a66597_remove’:
drivers/usb/host/r8a66597-hcd.c:2401:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(r8a66597->reg);
^
drivers/usb/host/r8a66597-hcd.c: In function ‘r8a66597_probe’:
drivers/usb/host/r8a66597-hcd.c:2447:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
reg = ioremap(res->start, resource_size(res));
^
drivers/usb/host/r8a66597-hcd.c:2447:6: warning: assignment makes pointer from integer without a cast [enabled by default]
reg = ioremap(res->start, resource_size(res));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/host/xhci-mvebu.c: In function ‘xhci_mvebu_mbus_init_quirk’:
drivers/usb/host/xhci-mvebu.c:58:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
base = ioremap(res->start, resource_size(res));
^
drivers/usb/host/xhci-mvebu.c:58:7: warning: assignment makes pointer from integer without a cast [enabled by default]
base = ioremap(res->start, resource_size(res));
^
drivers/usb/host/xhci-mvebu.c:69:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(base);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_remove’:
drivers/usb/gadget/udc/m66592-udc.c:1538:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(m66592->reg);
^
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_probe’:
drivers/usb/gadget/udc/m66592-udc.c:1577:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
reg = ioremap(res->start, resource_size(res));
^
drivers/usb/gadget/udc/m66592-udc.c:1577:6: warning: assignment makes pointer from integer without a cast [enabled by default]
reg = ioremap(res->start, resource_size(res));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/net2272.c: In function ‘net2272_remove’:
drivers/usb/gadget/udc/net2272.c:2232:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(dev->base_addr);
^
drivers/usb/gadget/udc/net2272.c: In function ‘net2272_plat_probe’:
drivers/usb/gadget/udc/net2272.c:2650:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
dev->base_addr = ioremap_nocache(base, len);
^
drivers/usb/gadget/udc/net2272.c:2650:17: warning: assignment makes pointer from integer without a cast [enabled by default]
dev->base_addr = ioremap_nocache(base, len);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/host/isp116x-hcd.c: In function ‘isp116x_remove’:
drivers/usb/host/isp116x-hcd.c:1552:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(isp116x->data_reg);
^
drivers/usb/host/isp116x-hcd.c: In function ‘isp116x_probe’:
drivers/usb/host/isp116x-hcd.c:1604:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
addr_reg = ioremap(addr->start, resource_size(addr));
^
drivers/usb/host/isp116x-hcd.c:1604:11: warning: assignment makes pointer from integer without a cast [enabled by default]
addr_reg = ioremap(addr->start, resource_size(addr));
^
drivers/usb/host/isp116x-hcd.c:1613:11: warning: assignment makes pointer from integer without a cast [enabled by default]
data_reg = ioremap(data->start, resource_size(data));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In several drivers in the pxa architecture, it was found that the
platform_get_irq() was not propagated. This breaks the the device-tree
probe deferral path, if -EPROBE_DEFER is returned. Unfortunately, the
error return in this case is transformed into -ENXIO, breaking the
deferral mechanism.
Even if in this specific case the driver was not broken, because the
interrupt controller is always probed before drivers, propagate the
proper return code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should cut down latencies and waste if the tty layer writes single bytes.
Signed-off-by: Oliver Neukum >oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transfer burst count (TBC) field in the Isoc TRB does not fit the new
larger burst count available for USB 3.1 SSP Isoc tranfers.
xhci 1.1 solved this by reusing the TD size field for transfer burst count.
The Mult field was outgrown as well. xhci 1.1 controllers can calculate
Mult itself and is not set if the new layout is used.
xhci 1.1 controllers that support the new Isoc TRB format expose a
Extended TBC Capability (ETC). To take the new format into use the xhci
host controller driver needs to set a Extended TBC Enable (ETE) bit.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up xhci_queue_isoc_tx() and helpers to prepare them for USB 3.1 and
xhci 1.1 isoc TRB changes.
Only functional change is adding xhci version 1.1 to the BEI flag check
toghether with xhci version 1.0. Both versions behave the same.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperSpeedPlus doubled the number of transactions per service interval
the isoc endpoints supports.
To support this, xhci 1.1 added Large ESIT Capability (LEC), which
takes into use new bits in the endpoint context to fit the parameters.
If xhci supports LEC, and the device has a SuperSpeedPlus Isoc companion
descriptor then take into use the high bits of max esit payload, and
skip calculating the Mult field as it wouldn't fit. LEC capable
host will calculate the Mult based on other paramenters.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_endpoint_init() and helper functions were a bit messy.
Adding the higher bandwidth SuperSpeedPlus Isoc support on
top of it would make it even harder to read.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 devices that support precision time measurement have an
additional PTM cabaility descriptor as part of the full BOS descriptor
Look for this descriptor while parsing the BOS descriptor, and store it in
struct usb_hub_bos if it exists.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 devices can return a new SuperSpeedPlus isoc endpoint companion
descriptor for a isochronous endpoint that requires more than 48K bytes
per Service Interval.
The new descriptor immediately follows the old USB 3.0 SuperSpeed Endpoint
Companion and will provide a new BytesPerInterval value.
It is parsed and stored in struct usb_host_endpoint with the other endpoint
related descriptors, and should be used by USB3.1 capable hosts to reserve
bus time in the schedule.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixing the error reported by script checkpatch.pl
static variables blinkenlights and old_scheme_first
were initialised to 0, correcting it.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_bus_list has been removed and switched to idr
rename the related mutex accordingly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
xhci_find_next_ext_cap doesn't check for PCI hotplug removal and may use
the PCI master abort bit pattern (~0) to calculate a new PCI address
offset to read/write. The has lead to reproducable crashes when testing
surprise removal during device initialization on a Stratus platform, at
least after commit d5ddcdf4d6 ("xhci: rework xhci extended capability
list parsing functions").
The crash is repeatable on a Stratus platform when injecting hardware
faults to induce xHCI host controller hotplug during driver
initialization. If a PCI read in xhci_find_next_ext_cap returns the
master abort pattern, quirk_usb_handoff_xhci may start using a bogus
ext_cap_offset to start searching more bogus PCI addresses.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 got a fix for OTG Certification, DWC2 has two fixes for regressions on
RasPI, MUSB has a NULL pointer dereference fix for ux500 platforms and two
PHYs (MSM and MXS) got some minor fixes.
While at that, I'm also adding a fix to my email address which has changed
recently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhyq
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc2
DWC3 got a fix for OTG Certification, DWC2 has two fixes for regressions on
RasPI, MUSB has a NULL pointer dereference fix for ux500 platforms and two
PHYs (MSM and MXS) got some minor fixes.
While at that, I'm also adding a fix to my email address which has changed
recently.
Fix the following compiler warning (found by the kbuild test robot):
drivers/usb/host/ehci-hcd.c:312:13: warning: 'unlink_empty_async_suspended' declared 'static' but never defined
Commit 2a40f32454 ("USB: EHCI: fix regression during bus resume")
protected the function definition with a "#ifdef CONFIG_PM" block, so
now the declaration needs to be similarly protected. This patch moves
it to a better location.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During probe, in the device tree case, the data pointer associated to a
compatible is dereferenced. However, not all the compatibles are
associated to a private data pointer.
The generic-xhci and the xhci-platform don't need them, this patch adds a
test on the data pointer before accessing it, avoiding a kernel crash.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when ip fails to enter sleep mode, register access protection will
be disabled, at the same time if all clocks are disabled, access
register will hang up AHB bus.
the common case causes ip sleep failure is that after all ports
enter U3 but before ip enters sleep mode, a port receives a resume
signal('K'). this will happens when such as clicks mouse to try to
do remote-wakeup to stop system enter suspend.
so stop polling root hubs to avoid access xHCI register on bus
suspend, and restart it when bus resumes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when a LS or FS device doesn't connect though a HS hub,
the @bPkts field of its periodic endpoint context should
be set to 1.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI_SSIC_PORT_UNUSED quirk was applied to the xHCI host controllers
in some Intel SoC chips. With this quirk applied, SSIC port is set
to "unused" prior to xhci_suspend(). This may cause problem if host
fails to suspend. In this case, the port is set to unused without
host further entering D3, and the port will not be usable anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two workarounds introduced by commit b8cb91e058 ("xhci: Workaround
for PME stuck issues in Intel xhci") and commit abce329c27 ("xhci:
Workaround to get D3 working in Intel xHCI") share a single quirk bit
XHCI_PME_STUCK_QUIRK. These two workarounds actually are different and
might happen on different hardwares. Need to separate them by adding a
quirk bit for the later.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abce329c27 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit e210c422b6 ("xhci: don't finish a TD if we get a
short transfer event mid TD")
Turns out that most host controllers do not follow the xHCI specs and never
send the second event for the last TRB in the TD if there was a short event
mid-TD.
Returning the URB directly after the first short-transfer event is far
better than never returning the URB. (class drivers usually timeout
after 30sec). For the hosts that do send the second event we will go
back to treating it as misplaced event and print an error message for it.
The origial patch was sent to stable kernels and needs to be reverted from
there as well
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These ioctls provide support for the USBTMC-USB488 control requests
for REN_CONTROL, GO_TO_LOCAL and LOCAL_LOCKOUT
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a convenience function to obtain an instrument's
capabilities from its file descriptor without having to access sysfs
from the user program.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
In many situations operations on multiple instruments need to be
synchronized. poll/select provide a convenient way of waiting on a
number of different instruments and other peripherals
simultaneously.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
By configuring an instrument's event status register various
conditions can be reported via an SRQ notification. This complements
the synchronous polling approach using the READ_STATUS_BYTE ioctl
with an asynchronous notification.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
When performing a read on an instrument that is executing a function
that runs longer than the USB timeout the instrument may hang and
require a device reset to recover. The READ_STATUS_BYTE operation
always returns even when the instrument is busy permitting to poll
for the appropriate condition. This capability is referred to in
instrument application notes on synchronizing acquisitions for other
platforms.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a privileged operation so it doesn't matter much. We use "tmp"
as an offset into an array. If it were invalid we could read out of
bounds and trigger an oops if the memory is not mapped. Plus it makes
static checkers complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecassary casts in the argument to kfree.
Found using Coccinelle. The semantic patch used to find this is as follows:
//<smpl>
@@
type T;
expression *f;
@@
- kfree((T *)(f));
+ kfree(f);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unnecessary braces in single statement blocks at the
same time as replaces the if statement with a ternary conditional.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds parens to sizeof operator uses.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a blank line after declarations.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes comments conforming coding style.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an useless else branch after a break, reducing one
indent block.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes prohibited spaces before open parenthesis and open
brackets.
It also removes an assignment inside condition and unnecessary braces in
single statement block.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds spaces around operators.
Tested by compilation only.
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes useless initializations.
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the constants to right.
Tested by compilation only.
Caught by coccinelle:
scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an infinite 'for' loop and makes use of the already
existing 'restart' tag instead, reducing one leading tab.
The comments and code were corrected conforming file coding style.
Tested by compilation only.
Caught by checkpatch:
WARNING: Too many leading tabs - consider code refactoring
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the local STUB_DEBUG_FILES debugging
definition. STUB_DEBUG_FILES was used only in ehci-hcd, whereas
CONFIG_DYNAMIC_DEBUG is used all over the kernel.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a coding style issue reported by checkpatch related to
too many leading tabs.
This moves part of the fill_periodic_buffer() to the new function
output_buf_tds_dir().
Because it's inline, the file size has not changed.
Before:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
After:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a coding style issue reported by checkpatch related to
kmalloc_array usage.
On the same line the sizeof operand was enclosed in parentheses.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to conditional blocks without braces.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a coding style issue reported by checkpatch concerning
to usage of sizeof operand as a variable instead the type.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issue reported by checkpatch concerning to
an unnecessary line before close brace.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to missing line after variable declarations.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts macros into inline functions since the usage of
second is encouraged by Coding Style instead of the first.
Macros converted to functions:
- dbg_status
- dbg_cmd
- dbg_port
- speed_char
The size after changes remains the same.
Before:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
After:
text data bss dec hex filename
36920 81 12 37013 9095 drivers/usb/host/ehci-hcd.o
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to missing line after struct declarations.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch indents not empty functions to have the opening brace at the
beginning of the next line and body conforming coding style.
This also makes the function definition consistent with the file coding
style aligning parameters in sequential lines and indenting them with
two tabs.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces two snprintf() calls with scnprintf() in qh_lines()
and hence removes the unneeded sequential truncation tests.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to missing spaces around operators.
There is an additional change on line 49 that removes unnecessary
parentheses around ternary operands.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch puts the closing parenthesis at the statement end removing
unnecessary "new line".
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch concerning
to switch case statements. There are few additional changes made to fix
other coding styles issues.
These additional changes are:
- The compound statement "({...})" on line 474 is pulled out from
snprintf parameters.
- On line 723 the constant "0x03" is moved to right.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch.
Coding style demands usage of C89-style comments and a specific format
when it's multiline.
This also removes the Free Software Foundation address because FSF can
change it again.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch. The only
change in this patch that isn't just removing spaces before opening
square brackets is at line 213 where the initialization of fls_strings[]
is placed in same line.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coding style issues reported by checkpatch. The vast
majority of changes in this patch are removing spaces before opening
parenthesis, but in some cases, a few additional changes are made to fix
other coding style issues.
These additional changes are:
- Spaces around >> on line 50.
- On line 55 a call to ehci_dbg reduced to a single line.
- sizeof operands surrounded with parenthesis on lines 877, 883, 889
and 901.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the constant 0x3ff to right and put spaces
in the right shift.
Caught by coccinelle:
scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer operator must be sticked to name.
Caught by checkpatch:
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes trailing semicolon from macros.
Caught by checkpatch:
"WARNING: macros should not use a trailing semicolon"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put space after comma.
This patch also changes QH_NEXT macro for better reading.
Caught by checkpatch: "ERROR: space required after that ','"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prefer to use __aligned(size) macro instead of
__attribute__((aligned(size))).
Caught by checkpatch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use the 'do {} while (0)' wrapper in a single statement macro.
Caught by checkpatch: "WARNING: Single statement macros should not
use a do {} while (0) loop"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of space before open square bracket.
Caught by checkpatch: "ERROR: space prohibited before open square
bracket '['"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of space between function name and open parenthesis.
Caught by checkpatch: "WARNING: space prohibited between function name
and open parenthesis '('"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of spaces before comma.
Caught by checkpatch: "ERROR: space prohibited before that ','"
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The index variable of list_for_each_entry_safe is an offset from a list
pointer, and thus should not be NULL.
Generated by: scripts/coccinelle/iterators/itnull.cocci
CC: Geliang Tang <geliangtang@163.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quting the relevant thread:
> In fact, I suspect the locking added by the kernel 3.13 commit for
> read_descriptors() is invalid because read_descriptors() performs no USB
> activity; read_descriptors() just reads information from an allocated
> memory structure. This structure is protected as the structure is
> existing before and after the sysfs vfs descriptors entry is created or
> destroyed.
You're right. For some reason I thought that usb_deauthorize_device()
would destroy the rawdescriptor structures (as mentioned in that
commit's Changelog), but it doesn't. The locking in read_descriptors()
is unnecessary.
> The information is only written at the time of enumeration
> and does not change. At least that is my understanding.
>
> It is noted that in our testing of kernel 3.8 on ARM, that sysfs
> read_descriptors() was non-blocking because the kernel 3.13 comment was
> not there.
>
> The pre-kernel 3.13 sysfs read_descriptors() seemed to work OK.
>
> Proposal:
> =========
>
> Remove the usb_lock_device(udev) and usb_unlock_device(udev) from
> devices/usb/core/sysfs.c in read_descriptors() that was added by the
> kernel 3.13 commit
> "232275a USB: fix substandard locking for the sysfs files"
>
> Any comments to this proposal ?
It seems okay to me. Please submit a patch.
So this removes the locking making the point about -EINTR in
the first path moot.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
232275a USB: fix substandard locking for the sysfs files
introduced needed locking into sysfs operations on USB devices
It, however, uses uninterruptible sleep and if the error
handling is on extreme cases of sleep lengths of 10s of seconds
are possible. Unless we are removing the device we should use
interruptible sleep.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB bus numbering is based on directly dealing with bitmaps and
defines a separate list of busses.
This can be simplified and unified by using existing idr functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The speed field of the input slot context should represent the speed the
device is working at.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a xhci controller does not provide a protocol speed ID (PSI) table, a
default one should be used instead. Add the default values to the
SuperSpeedPlus device capability. Overwrite the default ones if a PSI table
exists. See xHCI 1.1 sectio 7.2.2.1.1 for more info
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unlink_empty_async_suspended() is marked __maybe_unused. This is
because its caller, ehci_bus_suspend(), is protected by "#ifdef
CONFIG_PM". We should use the same protection here instead of
__maybe_unused.
unlink_empty_async_suspended() gets called only when the root hub is
suspended. It's silly for it to call start_iaa_cycle() at such a
time; the IAA mechanism doesn't work when the root hub isn't running.
It should call end_unlink_async() instead. But even this isn't
necessary, since there already is a call to end_iaa_cycle() right
before the call to unlink_empty_async_suspended(). All we have to do
is interchange the two subroutine calls.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Reutman reports that an AMD/ATI EHCI host controller on one of
his computers does not stop transferring data when an active bulk QH
is unlinked from the async schedule. Apparently that host controller
fails to implement the IAA mechanism correctly when an active QH is
unlinked. This leads to data corruption, because the controller
continues to update the QH in memory when the driver doesn't expect
it. As a result, the next URB submitted for that QH can hang, because
the link pointers for the TD queue have been messed up. This
misbehavior is observed quite regularly.
To be fair, the EHCI spec (section 4.8.2) says that active QHs should
not be unlinked. It goes on to recommend a procedure that involves
waiting for the QH to go inactive before unlinking it. In the real
world this is impractical, not least because the QH may _never_ go
inactive. (What were they thinking?) Sometimes we have no choice but
to unlink an active QH.
In an attempt to avoid the problems that can ensue, this patch changes
how the driver decides when the unlink is complete. In addition to
waiting through two IAA cycles, in cases where the QH was not known to
be inactive beforehand we now wait until a 2-ms period has elapsed
with the host controller making no change to the QH data structure
(the hw_current and hw_token fields in particular). The intuition
here is that after such a long period, the endpoint must be NAKing and
hopefully the QH has been dropped from the host controller's internal
cache. There's no way to know if this reasoning is really valid --
the spec is no help in this regard -- but at least this approach fixes
Michael's problem.
The test for whether the QH is already known to be inactive involves
the reason for unlinking the QH originally. If it was unlinked
because it had halted, or it stopped in response to a short read, or
it overlaid a dummy TD (a silicon bug), then it certainly is inactive.
If it was unlinked because the TD queue was empty and no TDs have been
added to the queue in the meantime, then it must be inactive. Or if
the hardware status indicates that the QH is currently halted (even if
that wasn't the reason for unlinking it), then it is inactive.
Otherwise, if none of those checks apply, we go through the 2-ms
delay.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Reutman <mreutman@epiqsolutions.com>
Tested-by: Michael Reutman <mreutman@epiqsolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch improves the way ehci-hcd handles the iaa_in_progress flag.
The current code is somewhat careless in this regard:
The flag is meaningless when the root hub isn't running, most
particularly after the root hub has been suspended. But in
start_iaa_cycle(), the driver checks the flag before checking
the root hub's state. They should be checked in the opposite
order.
That routine also sets the flag too early, before it has
definitely committed to starting an IAA cycle.
The flag is turned off in end_unlink_async(). Upcoming
changes will call that routine at other times, not just at the
end of an IAA cycle. The two actions are logically separate
(although related), so we separate out a new routine to be
called in place of end_unlink_async() whenever an IAA cycle
ends: end_iaa_cycle().
iaa_in_progress should be turned off when the root hub is
suspended -- we certainly don't want it still to be set when
the root hub resumes. Therefore the call to
end_unlink_async() in ehci_bus_suspend() should also be
replaced with a call to end_iaa_cycle().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the "exception" bitflag in the ehci_qh structure
with a more explicit "unlink_reason" bitmask. This is for use in the
following patch, where we will need to have a good idea of the
reason for unlinking a QH, not just "something exceptional happened".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Michael Reutman <mreutman@epiqsolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes an issue found on Raspberry PI platform that prevents probe. Don't
skip setting the force mode if it's already set.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit 263b7fb557 ("usb: dwc2: Move reset into
dwc2_get_hwparams()") due to regression found on bcm2835 platform. USB
ethernet fails, due to being unable to pick up proper parameters when
performing a plain reset before reading hw params.
Below shows the results of the gnptxfsiz and hptxfsiz with and before
and after reverting this (from Stefan Wahren):
So here is the probe result before Patch 1 is applied:
[ 1.283148] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.313894] dwc2 20980000.usb: gnptxfsiz=00201000
[ 1.314104] dwc2 20980000.usb: hptxfsiz=00000000
[ 1.353908] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
[ 1.354262] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration.
[ 1.394249] dwc2 20980000.usb: DWC OTG Controller
[ 1.394561] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.394917] dwc2 20980000.usb: irq 33, io mem 0x00000000
And here is the probe result after Patch 1 is applied:
[ 1.280107] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.353949] dwc2 20980000.usb: gnptxfsiz=01001000
[ 1.354166] dwc2 20980000.usb: hptxfsiz=02002000
[ 1.434301] dwc2 20980000.usb: DWC OTG Controller
[ 1.434616] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.434973] dwc2 20980000.usb: irq 33, io mem 0x00000000
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The commit 7d32cdef53 ("usb: musb: fail with error when no DMA
controller set"), caused the core platform driver to correctly return an
error code when fail probing.
Unfurtante it also caused bug for a NULL pointer dereference, during
system suspend for the ux500 driver. The reason is a lacking validation
of the corresponding ->driver_data pointer, which won't be set when the
musb core driver fails to probe (or haven't yet been probed).
Fixes: 7d32cdef53 ("usb: musb: fail with error when no DMA...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Initialize vbus_value to be 0 since it's possible not to assign
any value before judgement.
Acked-by: Peter Chen <peter.chen@nxp.com
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This driver registers for extcon events as part of its probe, but
never unregisters them in case of error in the probe path.
There were multiple issues noticed due to this missing error handling.
One of them is random crashes if the regulators are not ready yet by the
time probe is invoked.
Ivan's previous attempt [1] to fix this issue, did not really address
all the failure cases like regualtor/get_irq failures.
[1] https://lkml.org/lkml/2015/9/7/62
Without this patch the kernel would carsh with log:
...
Unable to handle kernel paging request at virtual address 17d78410
pgd = ffffffc001a5c000
[17d78410] *pgd=00000000b6806003, *pud=00000000b6806003, *pmd=0000000000000000
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u8:0 Not tainted 4.4.0+ #48
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Workqueue: deferwq deferred_probe_work_func
task: ffffffc03686e900 ti: ffffffc0368b0000 task.ti: ffffffc0368b0000
PC is at raw_notifier_chain_register+0x1c/0x44
LR is at extcon_register_notifier+0x88/0xc8
pc : [<ffffffc0000da43c>] lr : [<ffffffc000606298>] pstate: 80000085
sp : ffffffc0368b3a70
x29: ffffffc0368b3a70 x28: ffffffc03680c310
x27: ffffffc035518000 x26: ffffffc035518000
x25: ffffffc03bfa20e0 x24: ffffffc035580a18
x23: 0000000000000000 x22: ffffffc035518458
x21: ffffffc0355e9a60 x20: ffffffc035518000
x19: 0000000000000000 x18: 0000000000000028
x17: 0000000000000003 x16: ffffffc0018153c8
x15: 0000000000000001 x14: ffffffc03686f0f8
x13: ffffffc03686f0f8 x12: 0000000000000003
x11: 0000000000000001 x10: 0000000000000001
x9 : ffffffc03686f0f8 x8 : 0000e3872014c1a1
x7 : 0000000000000028 x6 : 0000000000000000
x5 : 0000000000000001 x4 : 0000000000000000
x3 : 00000000354fb170 x2 : 0000000017d78400
x1 : ffffffc0355e9a60 x0 : ffffffc0354fb268
Fixes: 591fc116f3 ("usb: phy: msm: Use extcon framework for VBUS and ID detection")
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Expressions of the form "tty->termios.c_*flag & FLAG"
are more clearly expressed with the termios flags macros,
I_FLAG(), C_FLAG(), O_FLAG(), and L_FLAG().
Convert treewide.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SxKT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc2
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
tty_init_termios() never returns an error; re-declare as void. Remove
unnecessary error handling from callers. Remove extern declarations
of tty_free_termios() and free_tty_struct() and re-declare in file
scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On nominal execution, private data allocated on port_probe and attach
are never freed. Add port_remove and release callbacks to free them
respectively.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Harald Linden reports that the ftdi_sio driver works properly for the
Yaesu SCU-18 cable if the device ids are added to the driver. So let's
add them.
Reported-by: Harald Linden <harald.linden@7183.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for two PIDs of LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The visor driver crashes in clie_5_attach() when a specially crafted USB
device without bulk-out endpoint is detected. This fix adds a check that
the device has proper configuration expected by the driver.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Fixes: cfb8da8f69 ("USB: visor: fix initialisation of UX50/TH55 devices")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix null-pointer dereference at probe should a (malicious) Treo device
lack the expected endpoints.
Specifically, the Treo port-setup hack was dereferencing the bulk-in and
interrupt-in urbs without first making sure they had been allocated by
core.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB serial console device ID for IAI Corp. RCB-CV-USB
USB to RS485 adaptor.
Signed-off-by: Peter Dedecker <peter.dedecker@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In function usb_reset_and_verify_device, the old BOS descriptor may
still be used before allocating a new one. (usb_unlocked_disable_lpm
function uses it under the situation that it fails to disable lpm.)
So we cannot set the udev->bos to NULL before that, just keep what it
was. It will be overwrite when allocating a new one.
Crash log:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000010
IP: [<ffffffff8171f98d>] usb_enable_link_state+0x2d/0x2f0
Call Trace:
[<ffffffff8171ed5b>] ? usb_set_lpm_timeout+0x12b/0x140
[<ffffffff8171fcd1>] usb_enable_lpm+0x81/0xa0
[<ffffffff8171fdd8>] usb_disable_lpm+0xa8/0xc0
[<ffffffff8171fe1c>] usb_unlocked_disable_lpm+0x2c/0x50
[<ffffffff81723933>] usb_reset_and_verify_device+0xc3/0x710
[<ffffffff8172c4ed>] ? usb_sg_wait+0x13d/0x190
[<ffffffff81724743>] usb_reset_device+0x133/0x280
[<ffffffff8179ccd1>] usb_stor_port_reset+0x61/0x70
[<ffffffff8179cd68>] usb_stor_invoke_transport+0x88/0x520
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This phone needs to be handled by a specialised firmware tool
and is reported to crash irrevocably if cdc-acm takes it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Intel 7260 modem, it is needed for host side to send zero
packet if the BULK OUT size is equal to USB endpoint max packet
length. Otherwise, modem side may still wait for more data and
cannot give response to host side.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current acm driver, the bulk-in callback function ignores the
URBs unlinked in usb core.
This causes unexpected data loss in some cases. For example,
runtime suspend entry will unlinked all urbs and set urb->status
to -ENOENT even those urbs might have data not processed yet.
Hence, data loss occurs.
This patch lets bulk-in callback function handle unlinked urbs
to avoid data loss.
Signed-off-by: Tang Jian Qiang <jianqiang.tang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove a call to dev_err() that was reporting an unsuccesful call to
kmalloc(), as reporting memory allocation failures is redundant. Instead
of logging the error, clean up previously allocated resources and abort
the probe with -ENOMEM. Before this change sisusb->SiS_Pr could be
dereferenced even if null after failure of memory allocation.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove three calls to dev_err() from sisusb_probe() as
reporting memory allocation failures is redundant:
- Remove a call to dev_err() that was reporting unsuccesful call to
kzalloc().
- Remove two calls to dev_err() that were reporting unsuccesful calls
to kmalloc().
One call to dev_err() reporting memory allocation is left unchanged as
the last patch of the series removes it.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes null test before calls to kfree() as kfree() can
handle null pointers safely.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file drivers/usb/misc/sisusbvga/sisusb.c had 6 assignments inside if
tests. This patch move the assignment outside the test. The changes
also fix the remaining 2 lines that were over 80 characters.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file drivers/usb/misc/sisusbvga/sisusb.c contained coding style
issues reported by checkpatch. This patch fixes the following
errors:
- 12 WARNING: braces {} are not necessary for single statement blocks
- 04 ERROR: return is not a function, parentheses are not required
- 03 ERROR: do not initialise statics to 0
- 1 WARNING: else is not generally useful after a break or return
- 1 WARNING: braces {} are not necessary for any arm of this statement
- 1 WARNING: Block comments use * on subsequent lines
One case in which braces are not necessary is left unchanged as other
patch of the series will fix it.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes whitespace coding style issues that can't be fixed
without adding newlines. This patch fixes the following checkpatch
warnings:
- 20 ERROR: trailing statements should be on next line
- 15 WARNING: line over 80 characters
- 03 WARNING: Missing a blank line after declarations
- 01 ERROR: space required after that ','
Five lines over 80 characters are left. The first three wont change as
the fix would require split the cast and variable name in different
lines which makes the code less readable. The last two will be fixed by
other patch in the series.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes whitespace coding style issues that can be fixed
within a single line. This patch fixes the following checkpatch
warnings:
- 83 ERROR: space required after that ','
- 13 ERROR: switch and case should be at the same indent
- 08 WARNING: please, no spaces at the start of a line
- 03 ERROR: space required before the open parenthesis '('
- 04 WARNING: suspect code indent for conditional statements
- 01 WARNING: space prohibited between function name and open parenthesis
- 01 ERROR: spaces required around that '='
- 01 ERROR: code indent should use tabs where possible
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use bus_to_hcd() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_usb_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices send response IUs when you'd expect a sense IU.
As a response to a wrong LUN that is within spec.
We cannot get away without handling for response IUs.
This version fixes the issues Hans raised.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry() instead of list_for_each() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry() instead of list_for_each() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver calls pci_set_mwi to enable memory-write-invalidate when it
is initialized, but does not call pci_clear_mwi when it is removed. Many
other drivers calls pci_clear_mwi when pci_set_mwi is called, such as
r8169, 8139cp and e1000.
This patch adds a function "ehci_pci_remove" to remove the pci driver.
This function calls pci_clear_mwi and usb_hcd_pci_remove, which can
fix the problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver calls ehci_mem_init to allocate memory resources.
But these resources are not freed when ehci_halt fails.
This patch adds "ehci_mem_cleanup" in error handling code to fix this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering usb_hcd_platform_shutdown to be called during
shutdown. This is a generic function that performs the
generic host stack's shutdown. It ensures that USB
operations do not continue while kexec boots a new kernel.
Signed-off-by: Azriel Samson <asamson@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default value for the 'transceiver select' field of
the PORTSC register may not always be correct. Previously
the phy-msm-usb driver would do this for us, but since
ehci-msm can now be instantiated standalone without any PHY
driver, the register needs to be explicitly initialized to
ULPI mode to properly communicate with the PHY.
This is not readily apparent, as firmware or bootloader code
also happen to pre-initialize this for us. However, it can
manifest when performing a driver unbind/rebind as follows:
cd /sys/bus/platform/drivers/msm_hsusb_host
echo QCOM8040:00 > unbind
echo QCOM8040:00 > bind
The EHCI core executes a controller reset as part of this,
and as a result the register in question would revert to
its default state and must be re-initialized properly.
Furthermore this may be useful in the future when adding
PM suspend/resume support.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow the EHCI MSM driver to probe against an ACPI enumerated
device with ID QCOM8040.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the EHCI MSM driver has a hard dependency to be created
by an OTG layer, namely the phy-msm-usb driver. In some cases or
board configurations we want to allow the EHCI host to be
instantiated without OTG capability. Instead, relax the dependency
on having an OTG PHY being present and call usb_add_hcd() directly.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable the silicon quirk which is normally enabled for HSIC
host mode. This would otherwise prevent low speed devices
from enumerating properly.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This splits one big probing function into two smaller ones. The main one
is now responsible for the generic stuff: allocating memory & enabling
power using GPIO. The new one contains code that is specific to the USB
2.0 bcma core.
This will allow adding support for the USB 3.0 bcma core (handling XHCI)
in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having "bool ohci" argument in bcma_hcd_create_pdev function limited it
to support two cases only (OHCI and EHCI) and put too much logic in it.
Lets make caller pass all required data. This adds few extra arguments
to the function call but will allow us to reuse this code and handle
more cases in the future (e.g. add XHCI support).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbasename() helper is dedicated to find a last part of the filename or
pathname. USB core uses open-coded variant of that helper.
Replace some lines of code by kbasename() call.
The current users do not have trailing slash and we are on the safe side to
make such change. I dig a history of the code under question up and found the
patch [1] that brought it along with the same to tty layer. The check for
trailing slash looks like copy'n'paste thing and I consider it as redundant.
[1] http://www.kernel.org/pub/linux/kernel//people/akpm/patches/2.5/2.5.69/2.5.69-mm3/broken-out/linus.patch
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change Power architecture specific APIs such as in_be32/out_be32
for registers read/write. Instead using ioread/writebe32 which are
defined for power as well as arm architecture
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Sriram Dash <sriram.dash@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb 3.1 extend the hub get-port-status request by adding different
request types. the new request types return 4 additional bytes called
extended port status, these bytes are returned after the regular
portstatus and portchange values.
The extended port status contains a speed ID for the currently used
sublink speed. A table of supported Speed IDs with details about the link
is provided by the hub in the device descriptor BOS SuperSpeedPlus
device capability Sublink Speed Attributes.
Support this new request. Ask for the extended port status after port
reset if hub supports USB 3.1. If link is running at SuperSpeedPlus
set the device speed to USB_SPEED_SUPER_PLUS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same way as SuperSpeed devices show "5000" as device speed we wan't to
show "10000" as the default speed for SuperSpeedPlus devices in sysfs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hcd roothub that supports HCD_USB31 is running at SuperSpeedPlus speed
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing coccicheck warning which recommends to use memdup_user instead
to reimplement its code, using memdup_user simplifies the code
./drivers/usb/core/devio.c:1398:11-18: WARNING opportunity for memdup_user
Signed-off-by: Rahul Pathak <rpathak@visteon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed an unnecessary space between a function name and arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbhs_pkt_handle structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, the change is needed
to prevent a compilation failure, when mach/irq.h is removed.
Additionally remove other unneeded includes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in arm-soc
a bit late, which is why we've kept it separate from the other updates
and are sending it separately here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LG3u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on
top of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates
of the ACPICA's copyright notices, a code fixup resulting from
a regression fix that was necessary in the upstream code only
(the regression fixed by it has never been present in Linux)
and a compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke
it on practically all architectures other than x86 and make a
couple of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether
or not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on
the problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up
a bit and update the MAINTAINERS information related to it
(Chanwoo Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bKJ9
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
* pm-core:
driver core: Avoid NULL pointer dereferences in device_is_bound()
platform: Do not detach from PM domains on shutdown
USB / PM: Allow USB devices to remain runtime-suspended when sleeping
PM / sleep: Go direct_complete if driver has no callbacks
PM / Domains: add setter for dev.pm_domain
device core: add device_is_bound()
Pull kbuild updates from Michal Marek:
- Make <modname>-m in makefiles work like <modname>-y and fix the
fallout
- Minor genksyms fix
- Fix race with make -j install modules_install
- Move -Wsign-compare from make W=1 to W=2
- Other minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Demote 'sign-compare' warning to W=2
Makefile: revert "Makefile: Document ability to make file.lst and file.S" partially
kbuild: Do not run modules_install and install in paralel
genksyms: Handle string literals with spaces in reference files
fixdep: constify strrcmp arguments
ath10k: Fix build with CONFIG_THERMAL=m
Revert "drm: Hack around CONFIG_AGP=m build failures"
kbuild: Allow to specify composite modules with modname-m
staging/ad7606: Actually build the interface modules
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Here is the big USB drivers update for 4.5-rc1. Lots of gadget driver
updates and fixes, like usual, and a mix of other USB driver updates as
well. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV2rUACgkQMUfUDdst+ym2XQCgqdDOlyGX5B//9CZ2kH1DrDW9
qLsAoLSBvw4hk+Aotv6tn8AayMpHwqV1
=pFLC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB drivers update for 4.5-rc1.
Lots of gadget driver updates and fixes, like usual, and a mix of
other USB driver updates as well. Full details in the shortlog. All
of these have been in linux-next for a while"
* tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (191 commits)
MAINTAINERS: change my email address
USB: usbmon: remove assignment from IS_ERR argument
USB: mxu11x0: drop redundant function name from error messages
USB: mxu11x0: fix debug-message typos
USB: mxu11x0: rename usb-serial driver
USB: mxu11x0: fix modem-control handling on B0-transitions
USB: mxu11x0: fix memory leak on firmware download
USB: mxu11x0: fix memory leak in port-probe error path
USB: serial: add Moxa UPORT 11x0 driver
USB: cp210x: add ID for ELV Marble Sound Board 1
usb: chipidea: otg: use usb autosuspend to suspend bus for HNP
usb: chipidea: host: set host to be null after hcd is freed
usb: chipidea: removing of_find_property
usb: chipidea: implement platform shutdown callback
usb: chipidea: clean up CONFIG_USB_CHIPIDEA_DEBUG reference
usb: chipidea: delete static debug support
usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG
usb: chipidea: udc: improve error handling on _hardware_enqueue
usb: chipidea: udc: _ep_queue and _hw_queue cleanup
usb: dwc3: of-simple: fix build warning on !PM
...
Pull misc vfs updates from Al Viro:
"All kinds of stuff. That probably should've been 5 or 6 separate
branches, but by the time I'd realized how large and mixed that bag
had become it had been too close to -final to play with rebasing.
Some fs/namei.c cleanups there, memdup_user_nul() introduction and
switching open-coded instances, burying long-dead code, whack-a-mole
of various kinds, several new helpers for ->llseek(), assorted
cleanups and fixes from various people, etc.
One piece probably deserves special mention - Neil's
lookup_one_len_unlocked(). Similar to lookup_one_len(), but gets
called without ->i_mutex and tries to avoid ever taking it. That, of
course, means that it's not useful for any directory modifications,
but things like getting inode attributes in nfds readdirplus are fine
with that. I really should've asked for moratorium on lookup-related
changes this cycle, but since I hadn't done that early enough... I
*am* asking for that for the coming cycle, though - I'm going to try
and get conversion of i_mutex to rwsem with ->lookup() done under lock
taken shared.
There will be a patch closer to the end of the window, along the lines
of the one Linus had posted last May - mechanical conversion of
->i_mutex accesses to inode_lock()/inode_unlock()/inode_trylock()/
inode_is_locked()/inode_lock_nested(). To quote Linus back then:
-----
| This is an automated patch using
|
| sed 's/mutex_lock(&\(.*\)->i_mutex)/inode_lock(\1)/'
| sed 's/mutex_unlock(&\(.*\)->i_mutex)/inode_unlock(\1)/'
| sed 's/mutex_lock_nested(&\(.*\)->i_mutex,[ ]*I_MUTEX_\([A-Z0-9_]*\))/inode_lock_nested(\1, I_MUTEX_\2)/'
| sed 's/mutex_is_locked(&\(.*\)->i_mutex)/inode_is_locked(\1)/'
| sed 's/mutex_trylock(&\(.*\)->i_mutex)/inode_trylock(\1)/'
|
| with a very few manual fixups
-----
I'm going to send that once the ->i_mutex-affecting stuff in -next
gets mostly merged (or when Linus says he's about to stop taking
merges)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
nfsd: don't hold i_mutex over userspace upcalls
fs:affs:Replace time_t with time64_t
fs/9p: use fscache mutex rather than spinlock
proc: add a reschedule point in proc_readfd_common()
logfs: constify logfs_block_ops structures
fcntl: allow to set O_DIRECT flag on pipe
fs: __generic_file_splice_read retry lookup on AOP_TRUNCATED_PAGE
fs: xattr: Use kvfree()
[s390] page_to_phys() always returns a multiple of PAGE_SIZE
nbd: use ->compat_ioctl()
fs: use block_device name vsprintf helper
lib/vsprintf: add %*pg format specifier
fs: use gendisk->disk_name where possible
poll: plug an unused argument to do_poll
amdkfd: don't open-code memdup_user()
cdrom: don't open-code memdup_user()
rsxx: don't open-code memdup_user()
mtip32xx: don't open-code memdup_user()
[um] mconsole: don't open-code memdup_user_nul()
[um] hostaudio: don't open-code memdup_user()
...
The big thing here is Tegra210 support, which is really only the Kconfig
symbol. Other than that there's a few miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zr7c
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into late/tegra
ARM: tegra: Core SoC changes for v4.5-rc1
The big thing here is Tegra210 support, which is really only the Kconfig
symbol. Other than that there's a few miscellaneous fixes.
* tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
Signed-off-by: Olof Johansson <olof@lixom.net>
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Have dev_pm_ops.prepare return 1 for USB devices and ports so that USB
devices can remain runtime-suspended when the system goes to a sleep
state, if their wakeup state is correct and they have runtime PM enabled.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid that building with W=1 triggers compiler warnings about
set-but-not-used variables.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here's another device id for cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jeCr
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for v4.4-rc8
Here's another device id for cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
These updates add support for Moxa UPort 1100-series devices through a
new mxu11x0 driver.
The cp210x driver gains proper support for cp2108 devices by working
around a couple of firmware bugs, and generic wait-until-sent support
(e.g. for tcdrain) is also added.
Included are also some general clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tyK5
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.5-rc1
These updates add support for Moxa UPort 1100-series devices through a
new mxu11x0 driver.
The cp210x driver gains proper support for cp2108 devices by working
around a couple of firmware bugs, and generic wait-until-sent support
(e.g. for tcdrain) is also added.
Included are also some general clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant function name from a few error messages.
Drop redundant error message when generic open fails.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to release the private data before returning -ENODEV after
having downloaded the firmware during first probe.
Clean up the error paths while at it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix memory leak in port-probe error path by verifying the interrupt-in
urb before allocating the private data.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a driver which supports :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
This driver is based on GPL MOXA driver written by Hen Huang and available
on MOXA website. The original driver was based on io_ti serial driver.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the USB device ID for ELV Marble Sound Board 1.
Signed-off-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWfLjWAAoJEEhZKYFQ1nG7R/cH/3xP4nz3pDDOpsX6U8Q1V81D
K7118WeAOx64sdGRZ3bsEjNko4NI1j2jcQU2Zgtx/I5Q0lJfNm4linNNWJHKEb/m
1VJVxFJXP6lwWImVWNJbyvhzel8mlgaNza+ZabUOAFmSig9q3yHUq5lDqzPVLZWY
z7lYQS+sOsCorsQierXiRxSRvkipB32NpdfhEXkj6P6Ji2a1UDDRA7F3f9k9t8QR
iI1T5+gbJL/3eo+ToOdlGciIUjoa4bK5b0Iz+QeU2eSOqjuVcu4tZO5IJbH/o10Z
dAhcDOr0DPEGzfpwihevyX3HcRKTKHPlzo2GdW5TJ5e7vm5C43fGHB0GgpIJBWw=
=7ZBY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
The chipidea changes for v4.5-rc1
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vM4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
Directly manipulate the controller regsiter to suspend the usb bus
for HNP is not the proper way, this should be done through the usbcore
by usb autosuspend. So to start HNP, autosuspend support should be
added for OTG devices interface driver if it's not enabled.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Set ci->hcd and ci->otg.host to be null in host_stop since the
hcd already freed.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
call to of_find_property() before of_property_read_u32() is unnecessary.
of_property_read_u32() anyway calls to of_find_property() only.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
disable wakeup irq during shutdown, otherwise kexec fails for
kernels that setup irq handlers before resetting the hardware
Signed-off-by: Andreas Fenkart <andreas.fenkart@dev.digitalstrom.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Since this configuration option has deleted, cleans up all
its references.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Since we need to mount debugfs to show/store the things we
want to debug, it is duplicated to add another configuration
to enable it. Meanwhile, with CONFIG_USB_CHIPIDEA_DEBUG,
we can't support chipidea debugfs at runtime.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Jun Li <jun.li@freescale.com>
_hardware_enqueue() didn't check for errors when using
add_td_to_list() which can fail if dma_pool_alloc fails, thus
causing a kernel panic when lastnode->ptr is NULL.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Update comments to reflect current state of functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
if we have a !PM kernel build, our runtime
suspend/resume callbacks will be left defined but
unused. Add a ifdef CONFIG_PM guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In specific conditions (involving usb hubs) dwc2 devices can create a
lot of interrupts, even to the point of overwhelming devices running
at low frequencies. Some devices need to do special clock handling
at shutdown-time which may bring the system clock below the threshold
of being able to handle the dwc2 interrupts. Disabling dwc2-irqs
in a shutdown callbacks prevents reboots/poweroffs from getting stuck
in such cases.
The hsotg struct already contains an unused irq element, so we can
just use it to store the irq number for the shutdown callback.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The phy's init routine must be called before it can be used. Do so in
musb_init_controller and the matching shutdown in musb_remove.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "enumspd" field is located in register DSTS[2:1], but the code
which checks the bitfield does not shift the value accordingly. This
in turn causes incorrect detection of gadget link partner speed in
dwc2_hsotg_irq_enumdone() .
Shift the value accordingly to fix the problem with speed detection.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The
gadget_init function should not access any device registers because the
mode isn't guaranteed here.
Also, this is already called elsewhere before anything starts on the
gadget so it is not necessary here.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reset already happens before this so just force the dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The delay for force mode is only 25ms according to the databook.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2_core_reset() function exists in the core so use that one
instead.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the previously cached hw params in the gadget. This saves a reset
and force mode in the gadget initialization during probe and makes
getting the hardware parameters consistent between gadget and host.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds separate functions to get the host and device specific hardware
parameters. The functions check whether the parameters need to be read
at all, depending on dr_mode, and forces the mode only if necessary.
This saves some delays during probe. This also adds two device mode
parameters that will be used by the gadget.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
