This is V3 of Emma Mobile EV2 SMP support.
At this point only the most basic form of SMP operation
is supported. TWD and CPU Hotplug support is excluded.
Tied to both the Emma Mobile EV2 and the KZM9D board
due to the need to switch on board in platsmp.c and
the newly introduced need for static mappings.
The static mappings are needed to allow hardware
acces early during boot when SMP is initialized.
This early requirement forces us to also map in
the SMU registers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
V3 of basic KZM9D board support. At this point a quite
thin layer that makes use of the Emma Mobile EV2 SoC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is V3 of the Emma Mobile EV2 SoC support.
Included here is support for serial and timer
devices which is just about enough to boot a kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit ff9a184c ("ARM: 7400/1: vfp: clear fpscr length and stride bits
on entry to sig handler") flushes the VFP state prior to entering a
signal handler so that a VFP operation inside the handler will trap and
force a restore of ABI-compliant registers. Reflushing and disabling VFP
on the sigreturn path is predicated on the saved thread state indicating
that VFP was used by the handler -- however for SMP platforms this is
only set on context-switch, making the check unreliable and causing VFP
register corruption in userspace since the register values are not
necessarily those restored from the sigframe.
This patch unconditionally flushes the VFP state after a signal handler.
Since we already perform the flush before the handler and the flushing
itself happens lazily, the redundant flush when VFP is not used by the
handler is essentially a nop.
Reported-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A zero value for prot_sect in the memory types table implies that
section mappings should never be created for the memory type in question.
This is checked for in alloc_init_section().
With LPAE, we set a bit to mask access flag faults for kernel mappings.
This breaks the aforementioned (!prot_sect) check in alloc_init_section().
This patch fixes this bug by first checking for a non-zero
prot_sect before setting the PMD_SECT_AF flag.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
the old codes will cause 3.4 kernel warning as irq domain size is wrong:
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:74 irq_domain_legacy_revmap+0x24/0x48()
Modules linked in:
[<c0013f50>] (unwind_backtrace+0x0/0xf8) from [<c001e7d8>] (warn_slowpath_common+0x54/0x64)
[<c001e7d8>] (warn_slowpath_common+0x54/0x64) from [<c001e804>] (warn_slowpath_null+0x1c/0x24)
[<c001e804>] (warn_slowpath_null+0x1c/0x24) from [<c005c3c4>] (irq_domain_legacy_revmap+0x24/0x48)
[<c005c3c4>] (irq_domain_legacy_revmap+0x24/0x48) from [<c005c704>] (irq_create_mapping+0x20/0x120)
[<c005c704>] (irq_create_mapping+0x20/0x120) from [<c005c880>] (irq_create_of_mapping+0x7c/0xf0)
[<c005c880>] (irq_create_of_mapping+0x7c/0xf0) from [<c01a6c48>] (irq_of_parse_and_map+0x2c/0x34)
[<c01a6c48>] (irq_of_parse_and_map+0x2c/0x34) from [<c01a6c68>] (of_irq_to_resource+0x18/0x74)
[<c01a6c68>] (of_irq_to_resource+0x18/0x74) from [<c01a6ce8>] (of_irq_count+0x24/0x34)
[<c01a6ce8>] (of_irq_count+0x24/0x34) from [<c01a7220>] (of_device_alloc+0x58/0x158)
[<c01a7220>] (of_device_alloc+0x58/0x158) from [<c01a735c>] (of_platform_device_create_pdata+0x3c/0x80)
[<c01a735c>] (of_platform_device_create_pdata+0x3c/0x80) from [<c01a7468>] (of_platform_bus_create+0xc8/0x190)
[<c01a7468>] (of_platform_bus_create+0xc8/0x190) from [<c01a74cc>] (of_platform_bus_create+0x12c/0x190)
---[ end trace 1b75b31a2719ed32 ]---
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Current IRQ16-IRQ31 irq number are located around 800 from
1ee8299a9e
(ARM: mach-shmobile: Use 0x3400 as INTCS vector offset)
But, the PINT0/1 IRQ number are also located around 800 from
0df1a838d6
(ARM: mach-shmobile: sh73a0 PINT IRQ base fix)
This patch relocates PINT0/1 IRQ number to around 700 where is not used,
and adds current IRQ location table in comment area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.
Remove it and use the arch_dup_task_struct() instead.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
I got build errors with the new version now because machine_is_kzm9g is no longer
defined:
arch/arm/mach-shmobile/platsmp.c: In function 'shmobile_smp_get_core_count':
arch/arm/mach-shmobile/platsmp.c:29:2: error: implicit declaration of function 'of_machine_is_compatible'
Replace the missing function with a call to of_machine_is_compatible.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
irq_of_parse_and_map does not have an empty definition for the
!CONFIG_OF case, so we should not try to call it then:
arch/arm/mach-exynos/common.c: In function 'combiner_init':
arch/arm/mach-exynos/common.c:576:3: warning: implicit declaration of function 'irq_of_parse_and_map'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* clps711x/cleanup:
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds platform data for using S3C-HSOTG driver at
Universal_C210 target.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hsotg device to the NURI board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[Rebased on the newest git/kgene/linux-samsung #for-next]
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hsotg device to the GONI board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch supports to control usb otg phy of EXYNOS4210.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[Rebased on the newest git/kgene/linux-samsung #for-next]
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
[kgene.kim@samsung.com: squashed 2 patches together]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use AUXDATA to set the device names for controller instances
discovered from device tree.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Update EXYNOS5 device tree source files for EXYNOS5250 SoC.
This includes new additions to the EXYNOS5 dtsi and SMDK5250
dts files and few minor fixes.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree based instantiation of the interrupt combiner controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add irq_domain support for hardware interrupts of the interrupt combiner.
The hardware interrupts of all the instances of the combiner are grouped
in a single irq_domain.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A seperate bus_type instance is not required for EXYNOS5. The
existing bus_type instance used with EXYNOS4 is sufficient for
both EXYNOS4 and EXYNOS5. This also solves issue of uninitialized
usage of exynos4_subsys in EXYNOS4 power management code that is
reused for EXYNOS5 also. In addition to that, the existing
exynos4_subsys bus_type is renamed to exynos_subsys to indicate
that it is reused on both EXYNOS4 and EXYNOS5 platforms.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The fout clock of BPLL and MPLL have a selectable source on EXYNOS5250.
The clock options are a fixed divided by 2 clock and the output of the
PLL itself. Add support for these new clock instances.
Signed-off-by: Kisoo Yu <ksoo.yu@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: moved common pll stuff into s5p-clock.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add GPC4 bank instance which is included in rev1 of EXYNOS5.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We now have an additional classs of modules which are enumerated at I2C
address 0x22. Add hookup for these modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Bells module now has a number assigned to it. Also hook up the WM9081
which is soldered down onto the board.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Store uids and gids with kuid_t and kgid_t in struct kstat
- Convert uid and gids to userspace usable values with
from_kuid and from_kgid
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This patch contains two changes:
- Removed unused definitions from mach/irqs.h
- Do not mask interrupts in ack procedure, because we have separate
intX_mask procedure for do it and actually these 2 functions are
called sequentially
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The nomadik gpio code has been converted to pinctrl, but the nomadik platform
still expects the old code to be present. Change it to use the new one instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Remove MX2_CAMERA_SWAP16 and MX2_CAMERA_PACK_DIR_MSB flags
so that the driver can negotiate with the attached sensor
whether the mbus format needs convertion from UYUV to YUYV
or not.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes in the dt2 branch move stuff around that gets changed
in the drivers/mmc branch. I chose a non-obvious resolution by
adding the new bus-width property into all the tegra sdhci device
nodes.
Conflicts:
arch/arm/boot/dts/tegra-cardhu.dts
arch/arm/boot/dts/tegra-harmony.dts
arch/arm/boot/dts/tegra-ventana.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* drivers/mmc:
mmc: dt: Consolidate DT bindings
Also pulls in the omap/dt-missed-3.4 branch as a dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'kirkwood_boards_for_v3.5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
Includes an update to v3.4-rc7
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"Rafael J. Wysocki" <rjw@sisk.pl> writes:
Renesas ARM-based platforms: new boards support for v3.5
* Support for the KZM-A9-GT board from Kuninori Morimoto and Magnus Damm.
* Support for the armadillo800eva board from Kuninori Morimoto and Magnus Damm.
This is based on the Renesas core SoC code updates I've sent a separate pull
request for.
* 'board-new' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas: (29 commits)
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
ARM: mach-shmobile: pfc-sh73a0: fixup MSEL2CR MSEL18 for I2C-3
ARM: mach-shmobile: kzm9g: add ST1232 Touchscreen support
ARM: mach-shmobile: kzm9g: add LCDC support
ARM: mach-shmobile: kzm9g: add external USB Host support
ARM: mach-shmobile: kzm9g: add SMSC 9221 support
ARM: mach-shmobile: kzm9g: add defconfig
ARM: mach-shmobile: add KZM-A9-GT board support
ARM: mach-shmobile: armadillo800eva: defconfig update
ARM: mach-shmobile: clock-r8a7740: add sh-eth clock
ARM: mach-shmobile: r8a7740: reserve DMA memory for the frame buffer
ARM: mach-shmobile: armadillo800eva: add MMCIF support
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Redefine IRQ_MCT_L0,1 irq definition as it is changed in rev1 of EXYNOS5.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adapt to changes in GIC physical address in rev1 of EXYNOS5.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add watchdog timer clock instance for EXYNOS5 watchdog controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds the required platform data and calls to enable
the CRYP/HASH driver.
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as
currently possible in the devicetree files, including the NAND partitions.
Use the partition scheme of the original firmware by default.
Create a board-ib62x0.c for everything else.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The maxburst/chunk size was taken from the private slave DMA data structure.
Use the common API provided by DMA_SLAVE_CONFIG to setup src/dst maxburst
values.
The ctrla field is not needed anymore in the slave private structure nor the
header constants that were located in an architecture specific directory.
The at91sam9g45_devices.c file that was using this platform data is also
modified to remove this now useless data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add support for Iomega Iconnect system.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
dns323 and (at least) iconnect platforms are using hw led blinking, so,
instead of having 2 identicals .gpio_blink_set gpio-led hooks, move
dns323 code into gpio.c
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
gpio registers are for 32 gpios. Given that orion_gpio_set_blink is called
directly and not through gpiolib, it needs to make sure that the pin value
given to the internal functions are between 0 and 31.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use devicetree to define NAND partitions. Use D-link partition scheme by
default, to be vaguely compatible with their userland.
Changes since last submission (V4):-
* Don't add NAND support then throw it away immediately after [Grant Likely]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.
Changes since last submission (V3) [Addressing comments by]:-
* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49
Changes since last submission (V2):-
* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board.
Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use DT_MACHINE_START() on the sh73a0 based KZM9G board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds platform data for the AT91 ADC driver support for
the AT91SAM9M10G45-EK board.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds platform data for the AT91 ADC driver support for
the AT91SAM9G20-EK board.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Warren <swarren@wwwdotorg.org> writes:
This branch is based on the merge of the following branches from the
Tegra repo, which are all already pulled into arm-soc:
for-3.5/tegra30-audio
for-3.5/usb-ulpi
for-3.5/dt
... which are all based on for-3.5/gpio-pinmux
* 'for-3.5/dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kukjin Kim <kgene.kim@samsung.com> writes:
As there were discussions, some exynos4 boards have been updated because
current dt cannot support all features for current board files on
exynos4.
Note, this should be merged after next/devel-samsung because some
platform devices are defined in that.
* 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add FIMC device to SMDK4X12
ARM: EXYNOS: Add MFC device to SMDK4X12
ARM: EXYNOS: Add DRM device to SMDKV310
ARM: EXYNOS: Add DRM device to Origen
ARM: EXYNOS: Make BT platform data structure static in mach-origen.c file
ARM: EXYNOS: Add DRM core support for NURI board
ARM: EXYNOS: Add DRM core device support for Universal C210 board
ARM: EXYNOS: Increase framebuffer virtual size for origen
ARM: S3C64XX: Hook up new style regulator-regulator supplies on Cragganmore
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omap/dt branch adds a few instances of mmc device nodes that
need to get changed to use the common bindings. Pull that into
a new branch so we can apply the patch in a single run.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kukjin Kim <kgene.kim@samsung.com> writes:
We can remove plat-s5p directory with this series and I think, the
plat-s3c24xx can be removed next time for one plat-samsung of Samsung
stuff.
Note, this is including cleanup-samsung-iommu which is removing s5p
iommu stuff in plat-s5p.
* 'next/cleanup-plat-s3c24xx-s5p' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All functions from this header already provided by common.c
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ep7312 has been supported for a very long time, but has never
been mentioned in the Kconfig file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no reason to have the clps7111.h header in a globally
visible location, so move it to a place that is only visible when
building for mach-clps711x.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In tegra*.dtsi, set status="disable" for all HW modules that the board
design may choose not to use. Update all boards to specifically enable
any of those modules that are useful by setting status="okay".
This makes board files say which features they do use, rather than which
they don't, which feels more logical. It also makes the .dts files
slightly smaller, at least for existing content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Put properties in order compatible, reg, interrupts, then anything else
the node has.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
name.
The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
It's already specified in skeleton.dtsi, included via tegra20.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Place each reg "entry" on its own line, and wrap the whole list in
<> rather than each individual entry.
The convention chosen here is slightly arbitrary, but is not consistent
throughout all Tegra files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Ensure that all Tegraa GPIO specifiers contain a comment indicating which
GPIO name the number refers to.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
DT node names only need to include the unit address if it's required to
make the node name unique. Remove the unnecessary unit addresses.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Cardhu's eMMC controller is on sdhci@78000600, not sdhci@78000400.
Fix the typo. This roughly doubles the IO performance, since the
support-8bit property actually takes effect.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org # v3.4
Add device info for the core regulator tps62360 in tegra-cardhu
dts file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed node name to reflect actual device type]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
flowctrl_write_cpu_csr uses the cpu halt offsets and vice versa. This patch
fixes this bug.
Reported-by: Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[swarren: This problem was introduced in v3.4-rc1, in commit 26fe681 "ARM:
tegra: functions to access the flowcontroller", when this file was first
added]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move to using a refined pr_fmt to avoid having to manually
prefix every message line with 'ts78xx'.
Changelog:
v2: moved pr_fmt define ahead of includes as suggested by
Hartley Sweeten to avoid use of leading undef
v1: initial release
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Move ts78xx_fpga from /sys/power to /sys/firmware so that
we can remove the PM dependency.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Changelog:
v2: use DEFINE_RES_MEM as suggesed by Hartley Sweeten
v1: inital release
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Orion5x board files which don't have PCI give warnings:
arch/arm/mach-orion5x/common.h:54:38: warning: 'struct pci_dev' declared
inside parameter list.
Add a forward declaration in the header file, which is the pattern
used for other PCI structures.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
There are no board specific configurations that need user
intervention, so just make MACH_SPEAR600 the silent default
for ARCH_SPEAR6XX to prevent users from turning it off, which
would result in a build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
This patch adds machines/boards dts{i} files for SPEAr1310 and SPEAr1340. Both
are based on ARM, Cortex A9 processor family.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
This adds pinctrl driver for SPEAr13xx family. SPEAr13xx family supports two
machines: SPEAr1310 and SPEAr1340.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides the suspend/resume support for EXYNOS4412.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Conflicts:
arch/arm/mach-ux500/cache-l2x0.c
arch/arm/mach-ux500/clock.c
arch/arm/mach-ux500/cpu.c
arch/arm/mach-ux500/mbox-db5500.c
arch/arm/mach-ux500/platsmp.c
arch/arm/mach-ux500/timer.c
Resolve lots of identical conflicts between the removal of
u5500 and the addition of u8540.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Shawn Guo <shawn.guo@linaro.org> writes:
I chose to base it on Sascha's imx-common-clk series than -rc, because
otherwise it will keep patching clock file that has been removed by
imx-common-clk series. It also depends on imx-pinctrl pull-request
I just sent to be functional.
Note: when imx-common-clk and imx-pinctrl get merged together, the
following files will have conflicts. But the conflicts should not be
so hard to resolve.
[arnd: resolved those merge conflicts by pulling pinctrl branch]
* imx/dt: (24 commits)
ARM: dts: imx53-qsb: enable audio support
ARM: dts: imx51-babbage: enable audio support
ARM: imx: add audio codec clk lookup for imx53-qsb
ARM: imx: add audmux pad setting for imx51-babbage
ARM: imx: add more imx5 ssi clocks
ARM: dts: imx53-qsb: Add Dialog DA9053 PMIC support
ARM: dts: imx6q-sabrelite: add serial2 pinctrl support
ARM: dts: imx6q-sabrelite: add sound device imx6q-sabrelite-sgtl5000
ARM: imx6q_sabrelite: clk_register_clkdev cko1 for sgtl5000
ARM: imx6q: add ssi1_ipg clk_lookup
ARM: dts: imx6q-sabrelite: add audmux pinctrl support
ARM: dts: imx6q-sabrelite: add i2c1 pinctrl support
ARM: dts: imx6q-sabrelite: add audmux device
ARM: dts: imx6q-sabrelite: add ssi device
ARM: dts: imx6q-arm2: add pinctrl state for usdhc
ARM: imx6: Add UART2 for low-level debug
ARM: imx6q: register phy fixup only when CONFIG_PHYLIB is enabled
ARM: imx6q: move imx6q_sabrelite specific code to a dedicated function
ARM: dts: imx6q-sabrelite: Add SPI NOR support
ARM: dts: Add basic support for imx6q-sabresd
...
Pulls in imx/pinctrl and imx/clock as dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The naming EXYNOS4 is changed to EXYNOS for using shared SPI
config of EXYNOS4 and EXYNOS5. And S3C64XX_DEV_SPIn configs
are added to MACH_SMDK5250 config to use SPI on the EYXNOS5250.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
[kgene.kim@samsung.com: updated because of non-existing config]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a simple BCH ecc computation api, similar to the
existing Hamming ecc api. It is intended to be used by the MTD layer.
It implements the following features:
- support 4-bit and 8-bit ecc computation
- do not protect user bytes in spare area, only data area is protected
- ecc for an erased NAND page (0xFFs) is also a sequence of 0xFFs
This last feature is obtained by adding a constant polynomial to
the hardware computed ecc. It allows to correct bitflips in blank pages
and is extremely useful to support filesystems such as UBIFS, which expect
erased pages to contain only 0xFFs.
This api has been tested on an OMAP3630 board.
Artem: The OMAP maintainer Tony Lindgren gave us his blessing for merging
this patch via the MTD tree.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the Synaptics NavPoint touchpad to the hx4700 platform:
1. Change GPIO23_SSP1_SCLK value in hx4700_pin_config[] from an output
to an input, since the NavPoint is connected to SSP in SPI slave mode.
2. Add GPIO102_GPIO (NavPoint power) to hx4700_pin_config[].
3. Add navpoint platform_device to devices[].
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Current ARM7 Cirrus Logic product line contains only 3 cpu.
EP7312 - Fully functional.
EP7309 - Missing SDRAM interface.
EP7311 - Missing DAI.
It makes no sense to separate the header files to identify these differences,
it is only necessary to keep in mind the presence or lack of any features of
a specific CPU when writing code.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most PCI implementations perform simple root bus scanning. Rather than
having each group of platforms provide a duplicated bus scan function,
provide the PCI configuration ops structure via the hw_pci structure,
and call the root bus scanning function from core ARM PCI code.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most PCI implementations use the standard PCI swizzle function, which
handles the well defined behaviour of PCI-to-PCI bridges which can be
found on cards (eg, four port ethernet cards.)
Rather than having almost every platform specify the standard swizzle
function, make this the default when no swizzle function is supplied.
Therefore, a swizzle function only needs to be provided when there is
something exceptional which needs to be handled.
This gets rid of the swizzle initializer from 47 files, and leaves us
with just two platforms specifying a swizzle function: ARM Integrator
and Chalice CATS.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is at odds with the documentation in the file; it says pin 1 on
slots 24,25,26,27 map to IRQs 27,28,29,30, but the function will always
be entered with slot=0 due to the lack of swizzle function. Fix this
function to behave as the comments say, and use the standard PCI
swizzle.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Integrator swizzle function is almost the same as the standard PCI
swizzle, except for an initial check for pin = 0. Make the integrator
swizzle function a wrapper around the standard PCI swizzle function so
we preseve this behaviour while using common code.
[fix to use pci_std_swizzle from Linus Walleij]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'mxs/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6: (51 commits)
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
ARM: dts: enable mmc for imx23-evk
mmc: mxs-mmc: add device tree support
mmc: mxs-mmc: copy wp_gpio in struct mxs_mmc_host
mmc: mxs-mmc: have dma_channel than dma_res in mxs_mmc_host
mmc: mxs-mmc: use devm_* helper to make cleanup simpler
mmc: mxs-mmc: move header from mach into linux folder
mmc: mxs-mmc: get rid of the use of cpu_is_xxx
mmc: mxs-mmc: let ssp_is_old take host as parameter
mmc: mxs-mmc: use global stmp_device functionality
ARM: mxs: add gpio support for device tree boot
gpio/mxs: add device tree probe
gpio/mxs: get rid of the use of cpu_is_xxx
gpio/mxs: use devm_* helpers to make error handling simple
ARM: mxs: add mxs-dma dt support
ARM: mxs: do not add dma device by default
dma: mxs-dma: add device tree probe support
...
From Kukjin Kim:
"Mostly it is using common macro to define resources and clean up useless codes."
* 'next/cleanup-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (34 commits)
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
ARM: S3C64XX: Use common macro to define resources on mach-smdk6410.c
ARM: S3C64XX: Use common macro to define resources on mach-real6410.c
ARM: S3C64XX: Use common macro to define resources on mach-mini6410.c
ARM: S3C64XX: Use common macro to define resources on mach-crag6410.c
ARM: S3C64XX: Use common macro to define resources on mach-anw6410.c
ARM: S3C64XX: Use common macro to define resources on dev-uart.c
ARM: S3C64XX: Use common macro to define resources on dev-audio.c
ARM: S3C24XX: Use common macro to define resources on simtec-nor.c
ARM: S3C24XX: Use common macro to define resources on mach-vr1000.c
ARM: S3C24XX: Use common macro to define resources on mach-tct_hammer.c
ARM: S3C24XX: Use common macro to define resources on mach-rx1950.c
ARM: S3C24XX: Use common macro to define resources on mach-otom.c
ARM: S3C24XX: Use common macro to define resources on mach-nexcoder.c
...
* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM: mach-shmobile: bonito: make sure static function
ARM: mach-shmobile: sh7372 CEU supports up to 8188x8188 images
ARM: mach-shmobile: mackerel: Add FSI DMAEngine support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xjdL
-----END PGP SIGNATURE-----
Merge tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/pinctrl
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
I was hoping to be done with fixes for 3.4 but we got two branches from
subarch maintainers the last couple of days. So here is one last(?) pull
request for arm-soc containing 7 patches:
- 5 of them are for shmobile dealing with SMP setup and compile failures
- The remaining two are for regressions on the Samsung platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Q2un
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:
- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Rename arch/arm/mach-mxs/include/mach/mmc.h to
include/linux/mmc/mxs-mmc.h, so that mxs-mmc driver becomes
<mach/*> inclusion free.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
The register HW_SSP_VERSION is broken for ssp version detection,
as the address of the register is different between imx23 and imx28.
Let's use platform_device_id to detect the device, so that the use
of cpu_is_xxx can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
mach-exynos/dma.c is updated to support both exynos4 and exynos5.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since just plat-samsung can support all of Samsung stuff so
that there is no more need to keep the plat-s5p for S5P SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Update the KZM9G defconfig and the code in platsmp.c to support SMP on
the sh73a0 based KZM9G board. Also fix up the earlyprintk setting that
was previously incorrect.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch enable GPIO-KEY/FSI,
and remove debug settings,
and be cleanuped by c2330e286f script
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds extra GPIO via PCF8757 chip,
and use it as gpio-key.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The correct screen direction of KZM9G board needs
PORT226/SC settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
GPIO_NR is added in order to clarify end of GPIO array.
We can add extra GPIO from it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
MSEL2CR MSEL18 should be 1 if I2C-3
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
AS3711 chip initalization is required for enabling LCDC backlight,
but there is no driver for this chip.
So, this patch sends its settings when boot.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch uses r8a66597_hcd driver,
since renesas_usbhs driver doesn't support external R8A66597 chip.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This adds very basic KZM-A9-GT board (SH73a0) support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch enable USBFunc/SHDI/MMCIF,
remove debug settings,
and cleanuped by c2330e286f script
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
armadillo800eva board is using sh-eth, but clock-r8a7740 didn't care it.
This clock was enabled by boot-loader.
This patch fix it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The default 2MB size of DMA coherent memory isn't enough for allocate
frame buffer memory.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
We can switch CON8/CON14 by SW1.5
SDHI1 is CON8 (SW1.5 = ON)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
On armadillo800eva board,
CD (= Card Detect) pin is not connected to SDHI0_CD.
Then, we can use IRQ31 as card detect irq,
but it needs chattering removal operation.
We should use IRQ card detect in the future,
but this patch use polling mode at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
