When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the other chip info constants have helpers to get at them; add
one for max_vid to keep things consistent.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201110185720.18228-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When mv88e6xxx_fid_map return error, we lost free the table.
Fix it.
Fixes: bfb2554289 ("net: dsa: mv88e6xxx: Add devlink regions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhangxiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201109144416.1540867-1-zhangxiaoxu5@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The left shift of u16 variable high is promoted to the type int and
then sign extended to a 64 bit u64 value. If the top bit of high is
set then the upper 32 bits of the result end up being set by the
sign extension. Fix this by explicitly casting the value in high to
a u64 before left shifting by 16 places.
Also, remove the initialisation of variable value to 0 at the start
of each loop iteration as the value is never read and hence the
assignment it is redundant.
Addresses-Coverity: ("Unintended sign extension")
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20201109124008.2079873-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export the raw VTU data and related registers in a devlink region so
that it can be inspected from userspace and compared to the current
bridge configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201109082927.8684-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch has two controllable I/Os which are usually connected to LEDs. This
is useful to immediately visually see the PTP status.
These provide two signals:
* is_gm
This LED can be activated if the current device is the grand master in that
PTP domain.
* sync_good
This LED can be activated if the current device is in sync with the network
time.
Expose these via the LED framework to be controlled via user space
e.g. linuxptp.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch has the ability to take hardware generated time stamps per port for
PTPv2 event messages in Rx and Tx direction. That is useful for achieving needed
time synchronization precision for TSN devices/switches. So add support for it.
There are two directions:
* RX
The switch has a single register per port to capture a timestamp. That
mechanism is not used due to correlation problems. If the software processing
is too slow and a PTPv2 event message is received before the previous one has
been processed, false timestamps will be captured. Therefore, the switch can
do "inline" timestamping which means it can insert the nanoseconds part of
the timestamp directly into the PTPv2 event message. The reserved field (4
bytes) is leveraged for that. This might not be in accordance with (older)
PTP standards, but is the only way to get reliable results.
* TX
In Tx direction there is no correlation problem, because the software and the
driver has to ensure that only one event message is "on the fly". However,
the switch provides also a mechanism to check whether a timestamp is
lost. That can only happen when a timestamp is read and at this point another
message is timestamped. So, that lost bit is checked just in case to indicate
to the user that the driver or the software is somewhat buggy.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch has internal PTP hardware clocks. Add support for it. There are three
clocks:
* Synchronized
* Syntonized
* Free running
Currently the synchronized clock is exported to user space which is a good
default for the beginning. The free running clock might be exported later
e.g. for implementing 802.1AS-2011/2020 Time Aware Bridges (TAB). The switch
also supports cross time stamping for that purpose.
The implementation adds support setting/getting the time as well as offset and
frequency adjustments. However, the clock only holds a partial timeofday
timestamp. This is why we track the seconds completely in software (see overflow
work and last_ts).
Furthermore, add the PTP multicast addresses into the FDB to forward that
packages only to the CPU port where they are processed by a PTP program.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are
implementing features needed for Time Sensitive Networking (TSN) such as support
for the Time Precision Protocol and various shapers like the Time Aware Shaper.
This driver includes basic support for networking:
* VLAN handling
* FDB handling
* Port statistics
* STP
* Phylink
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MT7530/7531 has a global RX packet length register, which can be used
to set MTU.
Supported packet length values are 1522 (1518 if untagged), 1536,
1552, and multiple of 1024 (from 2048 to 15360).
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20201103050618.11419-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the good discussion with Florian from here:
https://lore.kernel.org/netdev/20200911000337.htwr366ng3nc3a7d@skbuf/
I realized that the VLAN settings on the NPI port (the hardware "CPU port",
in DSA parlance) don't actually make any difference, because that port
is hardcoded in hardware to use what mv88e6xxx would call "unmodified"
egress policy for VLANs.
So earlier patch 183be6f967 ("net: dsa: felix: send VLANs on CPU port
as egress-tagged") was incorrect in the sense that it didn't actually
make the VLANs be sent on the NPI port as egress-tagged. It only made
ocelot_port_set_native_vlan shut up.
Now that we have moved the check from ocelot_port_set_native_vlan to
ocelot_vlan_prepare, we can simply shunt ocelot_vlan_prepare from DSA,
and avoid calling it. This is the correct way to deal with things,
because the NPI port configuration is DSA-specific, so the ocelot switch
library should not have the check for multiple native VLANs refined in
any way, it is correct the way it is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qca8k only supports a switch-wide MTU setting, and the code to take
the max of all ports was only looking at the port currently being set.
Fix to examine all ports.
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: f58d2598cf ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201030183315.GA6736@earth.li
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.
This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.
Allow the VLAN configuration to be updated on Marvell DSA bridges,
otherwise we end up cutting all traffic when enabling vlan filtering.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1kYAU3-00071C-1G@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate the const array rate_table on the stack but instead it
static. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
29812 3824 192 33828 8424 drivers/net/dsa/bcm_sf2.o
After:
text data bss dec hex filename
29670 3920 192 33782 83f6 drivers/net/dsa/bcm_sf2.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201020165029.56383-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9953 Seville switch has 2 megabits of buffer split into 4360
words of 60 bytes each. 2048 * 1024 is 2 megabytes instead of 2 megabits.
2 megabits is (2048 / 8) * 1024 = 256 * 1024.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: a63ed92d21 ("net: dsa: seville: fix buffer size of the queue system")
Link: https://lore.kernel.org/r/20201019050625.21533-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MTU setting for this DSA switch is global so we need
to keep track of the MTU set for each port, then as soon
as any MTU changes, roof the MTU to the biggest common
denominator and poke that into the switch MTU setting.
To achieve this we need a per-chip-variant state container
for the RTL8366RB to use for the RTL8366RB-specific
stuff. Other SMI switches does seem to have per-port
MTU setting capabilities.
Fixes: 5f4a8ef384 ("net: dsa: rtl8366rb: Support setting MTU")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a devlink region to return the per port registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a strictly cosmetic change that renames some macros in
sja1105_dynamic_config.c. They were copy-pasted in haste and this has
resulted in them having the driver prefix twice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP IS1 is a VCAP module which can filter on the most common L2/L3/L4
Ethernet keys, and modify the results of the basic QoS classification
and VLAN classification based on those flow keys.
There are 3 VCAP IS1 lookups, mapped over chains 10000, 11000 and 12000.
Currently the driver is hardcoded to use IS1_ACTION_TYPE_NORMAL half
keys.
Note that the VLAN_MANGLE has been omitted for now. In hardware, the
VCAP_IS1_ACT_VID_REPLACE_ENA field replaces the classified VLAN
(metadata associated with the frame) and not the VLAN from the header
itself. There are currently some issues which need to be addressed when
operating in standalone, or in bridge with vlan_filtering=0 modes,
because in those cases the switch ports have VLAN awareness disabled,
and changing the classified VLAN to anything other than the pvid causes
the packets to be dropped. Another issue is that on egress, we expect
port tagging to push the classified VLAN, but port tagging is disabled
in the modes mentioned above, so although the classified VLAN is
replaced, it is not visible in the packet transmitted by the switch.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are deriving these from the constants exposed by the
hardware, we can delete the static info we're keeping in the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the actions are packed together in the action RAM, an incorrect
action width means that no action except the first one would behave
correctly.
The tc-flower offload has probably not been tested on this hardware
since its introduction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port mask width was larger than the actual number of ports, and
therefore, all fields following this one were also shifted by the number
of excess bits. But the driver doesn't use the REW_OP, SMAC_REPLACE_ENA
or ACL_ID bits from the action vector, so the bug was inconsequential.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.
The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.
Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the driver name and ASIC ID so that generic user space
application are able to know they're looking at sja1105 devlink regions
when pretty-printing them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in Documentation/networking/dsa/sja1105.rst, this switch
has a static config held in the driver's memory and re-uploaded from
time to time into the device (after any major change).
The format of this static config is in fact described in UM10944.pdf and
it contains all the switch's settings (it also contains device ID, table
CRCs, etc, just like in the manual). So it is a useful and universal
devlink region to expose to user space, for debugging purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll have more devlink code soon. Group it together in a separate
translation object.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous implementation failed to account for the "ports" node. The
actual port nodes are not child nodes of the switch node, but a "ports"
node sits in between.
Fixes: edecfa98f6 ("net: dsa: microchip: look for phy-mode in port nodes")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->speed holds a value of 10, 100, 1000 or 2500, but
QSYS_TAG_CONFIG_LINK_SPEED expects a value of 0, 1, 2, 3. So convert the
speed to a proper value.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
