Update the 'hw_timer_enabled' to 'false' wherever we are stopping
hardware generic timers, excecpt the case where we start them
again immediately.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inside ath9k_hif_usb_firmware_fail(), the instance of
'struct struct hif_device_usb' may be freed by
ath9k_hif_usb_disconnect() after
complete(&hif_dev->fw_done);
But 'hif_dev' is still accessed after the line code
above is executed.
This patch fixes the issue by not accessing 'hif_dev'
after 'complete(&hif_dev->fw_done)' inside
ath9k_hif_usb_firmware_fail().
Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now MCI work is being queued twice by profile and status
updation. Queue MCI work once when it is needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that led pin is filled and set to OFF before starting
the driver. With recent changes, drv_start is being called even
before led_init is being completed. This is causing led is always
OFF on driver load when the interface is UP. This patch splits the
led init and fills the led pin before register hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update all coex parameters in sigle place. So that we can avoid
redoing the same operation in mutiple places and it eases debugging.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before processing BT profiles or status messages, check whether
it is requested to flush BT profile. Otherwise it might increase
number of BT profiles that affects the WLAN performance. Also
flush the profiles when MCI is recovering from broken rx. After
flushing BT profiles, query BT topology to refetch them.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the 9462 is operating in 2G mode and MCI is enabled then
reduce the selfgen chain mask to chain 1. Otherwise poor performance
was reported at short range at Rx side when COEX is enabled.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During fast channel change, perform 2g5g_switch before starting
noisefloor calibration to avoid nfload timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the driver specific SGI flag based on the station's
HT capabilities, otherwise rate control uses the wrong rate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register macros for antenna diversity are common for
AR9462 and AR9565, rename them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever BT calibration requested, WLAN has to wait for the
calibration to be completed. But right now we defer the waiting
which might cause BT calibration to fail. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various parts of the code require AR9565 checks,
this patch adds them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And recognize the device in the init path.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having generic hardware timer interrupt in debugfs
would come handy when we are debugging 3 WIRE
BTCOEX issues.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read and configure thermometer calibration results read from
OTP card.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before disabling BTCOEX in the h/w cancel all BTCOEX related
works. This is similar to the commit in ath9k(c32cdbd8)
ath9k: Stop the BTCOEX timers before disabling BTCOEX
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable BTCOEX for WB193(which seems to be the only supported
ath9k_htc BTCOEX chipset)only when it is enabled via modparam,
rather than enabling it by default.
Cc: Vivek Natarajan <nataraja@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Remove all the checks that will be handled by cfg80211
based on the interface combination advertised. For instance,
driver supports at the maximum 8 beaconing interface, while
we advertise maximum 8 beaconing interface in the interface
combination support.
*cfg80211 will take care of not allowing
us to add an interface that is not supported by the
driver, further if the change_interface changes the
old interface to a beaconing interface while we had
reached the max limit of 8 beaconing interface, again
cfg80211 takes care of this stuff!
So remove all these checks.
*Beautify placing PS wrappers in the appropriate
position.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Additionally it has a neat debug message informing us
that we are stopping the ANI algorithm.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its more correct to convert btcoex_period to 'us' while
comparing with btcoex_no_stomp which is in 'us'.
Did not find any functionality issues being fixed,
as the generic hardware timer triggers are usually
refreshed with the newer duty cycle.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a possibility that AR_MCI_GPM_1 register can
return 0xdeadbeef and this results in caching of invalid
GPM index in ar9003_mci_is_gpm_valid. Ensure we
have appropriate checks to avoid this.
Cc: xijin luo <xijin@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX filter bit for a station would be set by the HW
when a frame is not acked. A frame would be completed with
ATH9K_TXERR_FILT status only when the corresponding filter bit
for the destination station is already set.
Currently, un-acknowledged packets are added to the pending queue
and retried, but the "clear_dest_mask" bit in the descriptor is
set only when the TX status has been ATH9K_TXERR_FILT. This results
in packet loss and the log shows:
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746071
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746076
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746377
...
...
This issue can be resolved by making sure that the destination
mask is cleared when the packet is being retried and the earlier
TX status is ATH9K_TXERR_XRETRY.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the MCI BT state locally, rather than unnecessarily calling
ar9003_mci_state and updating it.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not necessary to hold the firmware memory during the whole
driver lifetime, and obviously it does waste memory. Suppose there
are 4 ath9k-htc usb dongles working, kernel has to consume about
4*50KBytes RAM to cache firmware for all dongles. After applying the
patch, kernel only caches one single firmware image in RAM for
all ath9k-htc devices just during system suspend/resume cycle.
When system is ready for loading firmware, ath9k-htc can request
the loading from usersapce. During system resume, ath9k-htc still
can load the firmware which was cached in kernel memory before
system suspend.
Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of changes in the supported rates set for a given station, it is now
possible to use this callback to update the current internal state of the
station in the htc driver.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
