After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.
Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=8KX8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Looks like omap3 is still relying on hwmod data for some basic
device tree information. Let's add the information to omap3.dtsi
so we can remove the related hwmod data once omap3 is DT only.
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.
Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
Now pinctrl-single-omap can handle the wake-up events for us now
as long as the events are configured in the .dts files.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some nodes in OMAP3 DTS now use edge or level sensitive interrupts.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
This patch updates the in-kernel dts files according to the latest cpus
and cpu bindings updates for ARM.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit ad871c10 (ARM: dts: OMAP: Add usb_otg and glue data to
OMAP3+ boards) added support for MUSB on omap3 for device tree,
but added the interrupts the wrong way probably as they were
copied from the omap4.dtsi file. On omap3 we have TI specific
interrupt controller, not GIC.
Fix this by specifying the interrupt following the TI INTC
binding.
Without this fix MUSB won't work as it is trying to use
irq0 instead of irq92.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi). Move the phy declaration to the dts
files.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix 'function-mask' referring to TRM (Omap 36xx) Section 13.4.4:
"Pad Functional Multiplexing and Configuration".
- Fix 'omap3_pmx_wkup' referring to TRM Table 13-6:
"Wkup Control Module Pad Configuration Register Fields".
Note that these fixes are not critical currently as we
are not yet using the missing range of pinmux registers
at this point.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the "ti,gpio-always-on" property to the appropriate GPIO banks to
indicate which banks are always powered and will never lose logic state.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Update the DMTIMER compatibility property to reflect the register level
compatibilty between devices and update the various OMAP/AM timer
bindings with the appropriate compatibility string.
By doing this we can add platform specific data applicable to specific
timer versions to the driver. For example, errata flags can be populated
for the timer versions that are impacted.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The OMAP3 gpio bindings are currently missing the reg and interrupt
properties and so add these properties.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The OMAP gpio binding documention [1] states that the #interrupts-cells
property for gpio controllers should be 2. Currently, for OMAP3+ devices
the #interrupt-cells is set to 1. By setting this property to 2, it
allows clients to pass a 2nd parameter indicating the sensitivity (level
or edge) and polarity (high or low) of the interrupt. The OMAP gpio
controllers support these options and so update the #interrupt-cells
property for OMAP3+ devices to 2.
[1] Documentation/devicetree/bindings/gpio/gpio-omap.txt
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add SDMA controller binding for OMAP2+ devices and populate DMA client
information for SPI and MMC peripheral on OMAP3+ devices. Please note
that OMAP24xx devices do not have SPI and MMC bindings available yet and
so DMA client information is not populated.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add PMU nodes for OMAP2, OMAP3 and OMAP4460 devices.
Please note that the node for OMAP4460 has been placed in a separate
header file for OMAP4460, because the node is not compatible with
OMAP4430. The node for OMAP4430 is not included because PMU is not
currently supported on OMAP4430 due to the absence of a cross-trigger
interface driver.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI),
mode which is mostly OTG, power that specifies the amount of power
this can supply when in host mode.
The information about usb otg node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Currently the OMAP General-Purpose Memory Controller (GPMC) device
node maps 16 MB of address space for its hardware registers.
This is because the OMAP Technical Reference Manual says that the
GPMC module register address space size is 16 MB. But in practice
the maximum address offset used by a GPMC register is 0x02d0.
So, there is no need to map such a big address space for GPMC regs.
This change was suggested by Jon Hunter [1].
[1]: https://patchwork.kernel.org/patch/2057111/
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add device-tree support for the GPMC controller on the OMAP3.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Adds the counter-32k timers nodes present in OMAP2/3/4 devices and
device-tree binding documentation for OMAP counter-32k.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the 12 GP timers nodes present in OMAP2.
Add the 12 GP timers nodes present in OMAP3.
Add the 11 GP timers nodes present in OMAP4.
Add the 7 GP timers nodes present in AM33xx.
Add documentation for timer properties specific to OMAP.
Thanks to Vaibhav Hiremath for creating the AM33xx timer nodes. I have modified
Vaibhav's original nodes adding information on which timers support a PWM
output.
V5 changes:
- Updated timer register sizes for OMAP2/3/4.
- Modified AM335x timer register size to be 1KB instead of 4KB to align with
HWMOD.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-Reviewed-&-Tested-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
The interrupt-parent attribute does not have to be added in each
node since the fmwk will check for the parent as well to get it.
Create an interrupt-parent for OMAP2, OMAP3, AM33xx and remove the
attributes from every nodes that were using it.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sebastien Guiriec <s-guiriec@ti.com>
Fixes the following errors:
[ 2.318084] omap-mcbsp 49022000.mcbsp: invalid rx DMA channel
[ 2.324432] omap-mcbsp 49024000.mcbsp: invalid rx DMA channel
Which is because we failed to link the sidetone hwmod for McBSP2/3. The
missing sidetone hwmod link will prevent omap_device_alloc() to append the
DMA resources since we - accidentally - end up having the same number of
resources provided from DT (IO/IRQ) as we have in hwmod for the McBSP ports
without the ST resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl driver entries for omap2+. These all use
the generic pinctrl-single driver for the padconf
registers.
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: updated to drop omap2420.dtsi rename changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The extra serial port is not available on 34xx. And the current
omap3-beagle.dts file is for omap3-beagle-xm.dts as it lists 512MB
of memory.
Please somebody submit a new omap3-beagle.dts for the original 34xx
BeagleBoard after testing it properly.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create the needed sections to be able to probe McBSP ports via DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add OMAP mmc related device tree data for OMAP3.
Currenly limited to only omap3-beagle board.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the 4 McSPI controller nodes present in an OMAP3 device.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Update the DTS with the proper information required by the
INTC bindings.
- Add the number of interrupt lines
- Add the reg and the compatible entries.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Add i2c controllers nodes into the main ocp bus.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Follow the DTS convention and thus name the nodes <name>@<address> without
any '0x' prefix in the physical address.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Pass minimal data needed for console boot, from dt, for
OMAP4 panda/sdp and OMAP3 beagle boards, and get rid of the
static initialization from generic board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for devices used by PM code (mpu, dsp, iva).
Add a cpus node as well as recommended in the DT spec.
Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>
