Consider the following test case:
write_c0_compare(read_c0_count());
Even if the counter doesn't increment during execution, this might not
generate an interrupt until the counter wraps around. The CPU may
perform the comparison each time CP0 COUNT increments, not when CP0
COMPARE is written.
If mips_next_event() is called with a very small delta, and CP0 COUNT
increments during the calculation of "cnt += delta", it is possible
that CP0 COMPARE will be written with the current value of CP0 COUNT.
If this is detected, the function should return -ETIME, to indicate
that the interrupt might not have actually gotten scheduled.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM4710 uses the BMIPS32 core (like BCM6345), not the MIPS 4Kc core as
was previously believed.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Alexandros C. Couloumbis <alex@ozo.com>
Patchwork: https://patchwork.linux-mips.org/patch/1837/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were unconditionally sending SIGBUS with an empty siginfo on FP
emulator faults. This differs from what happens when real floating
point hardware would get a fault.
For most faults we need to send SIGSEGV with the faulting address
filled in in the struct siginfo.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The return value of the vmalloc() call in arch/mips/kernel/vpe.c::vpe_open()
is not checked, so we potentially store a null pointer in v->pbuffer. Add
a check for a null return and then return -ENOMEM in that case.
[Ralf: The check added by Jesper's original patch is where it logically
should be. Adding it eleminated the need for the checks in a few other
places, so I removed them. There still is a zillion of other things that
need to be fixed in this file / API.]
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If PER_LINUX32 has been set on a 32-bit kernel, only twiddle with the
low-order personality bits, let the upper bits pass through.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We never needed that (->regs[2] is overwritten on return from syscall paths
with return value of syscall, so storing it there early made no sense) and
with new restart logics since d27240bf7e61d2656de18e158ec910a902030847 it
has become really bad - we lose the original syscall number before the
place where we decide that we might need a syscall restart.
Note that for child we do need the assignment to regs[2] - it won't go
through the normal return from syscall path.
[Ralf: Issue found and reported by Lluís; initial investigations by me;
bug finally found and patch by Al; testing by me and Lluís.]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Lluís Batlle i Rossell <viriketo@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TASK_SIZE macro should reflect the size of a user process virtual
address space. Previously for 64-bit kernels, this was not the case.
The immediate cause of pain was in
hugetlbfs/inode.c:hugetlb_get_unmapped_area() where 32-bit processes
trying to mmap a huge page would be served a page with an address
outside of the 32-bit address range. But there are other uses of
TASK_SIZE in the kernel as well that would like an accurate value.
The new definition is nice because it now makes TASK_SIZE and
TASK_SIZE_OF() yield the same value for any given process.
For 32-bit kernels there should be no change, although I did factor
out some code in asm/processor.h that became identical for the 32-bit and
64-bit cases.
__UA_LIMIT is now set to ~((1 << SEGBITS) - 1) for 64-bit kernels.
This should eliminate the possibility of getting a
AddressErrorException in the kernel for addresses that pass the
access_ok() test.
With the patch applied, I can still run o32, n32 and n64 processes,
and have an o32 shell fork/exec both n32 and n64 processes.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1701/
Some MIPS32R1 processors implement UserLocal (RDHWR $29) to accelerate
programs that make extensive use of thread-local storage. Therefore,
setting up the HWRENA register should not depend on cpu_has_mips_r2.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
BMIPS processor cores are used in 50+ different chipsets spread across
5+ product lines. In many cases the chipsets do not share the same
peripheral register layouts, the same register blocks, the same
interrupt controllers, the same memory maps, or much of anything else.
But, across radically different SoCs that share nothing more than the
same BMIPS CPU, a few things are still mostly constant:
SMP operations
Access to performance counters
DMA cache coherency quirks
Cache and memory bus configuration
So, it makes sense to treat each BMIPS processor type as a generic
"building block," rather than tying it to a specific SoC. This makes it
easier to support a large number of BMIPS-based chipsets without
unnecessary duplication of code, and provides the infrastructure needed
to support BMIPS-proprietary features.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Florian Fainelli <ffainelli@freebox.fr>
Patchwork: https://patchwork.linux-mips.org/patch/1706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
This patch adds the mipsxx Perf-events support based on the skeleton.
Generic hardware events and cache events are now fully implemented for
the 24K/34K/74K/1004K cores. To support other cores in mipsxx (such as
R10000/SB1), the generic hardware event tables and cache event tables
need to be filled out. To support other CPUs which have different PMU
than mipsxx, such as RM9000 and LOONGSON2, the additional files
perf_event_$cpu.c need to be created.
Raw event is an important part of Perf-events. It helps the user collect
performance data for events that are not listed as the generic hardware
events and cache events but ARE supported by the CPU's PMU.
This patch also adds this feature for mipsxx 24K/34K/74K/1004K. For how to
use it, please refer to processor core software user's manual and the
comments for mipsxx_pmu_map_raw_event() for more details.
Please note that this is a "precise" implementation, which means the
kernel will check whether the requested raw events are supported by this
CPU and which hardware counters can be assigned for them.
To test the functionality of Perf-event, you may want to compile the tool
"perf" for your MIPS platform. You can refer to the following URL:
http://www.linux-mips.org/archives/linux-mips/2010-10/msg00126.html
You also need to customize the CFLAGS and LDFLAGS in tools/perf/Makefile
for your libs, includes, etc.
In case you encounter the boot failure in SMVP kernel on multi-threading
CPUs, you may take a look at:
http://www.linux-mips.org/git?p=linux-mti.git;a=commitdiff;h=5460815027d802697b879644c74f0e8365254020
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1689/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/kernel/perf_event_mipsxx.c
This patch provides the skeleton of the HW perf event support. To enable
this feature, we can not choose the SMTC kernel; Oprofile should be
disabled; kernel performance events be selected. Then we can enable it in
Kernel type menu.
Oprofile for MIPS platforms initializes irq at arch init time. Currently
we do not change this logic to allow PMU reservation.
If a platform has EIC, we can use the irq base and perf counter irq offset
defines for the interrupt controller in specific init_hw_perf_events().
Based on this skeleton patch, the 3 different kinds of MIPS PMU, namely,
mipsxx/loongson2/rm9000, can be supported by adding corresponding lower
level C files at the bottom. The suggested names of these files are
perf_event_mipsxx.c/perf_event_loongson2.c/perf_event_rm9000.c. So, for
example, we can do this by adding "#include perf_event_mipsxx.c" at the
bottom of perf_event.c.
In addition, PMUs with 64bit counters are also considered in this patch.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1688/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Software events are required as part of the measurable stuff by the
Linux performance counter subsystem. Here is the list of events added by
this patch:
PERF_COUNT_SW_PAGE_FAULTS
PERF_COUNT_SW_PAGE_FAULTS_MIN
PERF_COUNT_SW_PAGE_FAULTS_MAJ
PERF_COUNT_SW_ALIGNMENT_FAULTS
PERF_COUNT_SW_EMULATION_FAULTS
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Acked-by: David Daney <ddaney@caviumnetworks.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Patchwork: https://patchwork.linux-mips.org/patch/1686/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The OCTEON II ISA extends the original OCTEON ISA, so give it its own
__elf_platform string so optimized libraries can be selected in
userspace.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1665/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows platforms that are using the swiotlb to initialize it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1638/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use new 'addrp', 'datavp' and 'datalp' variables in order to remove
unnecessary castings.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
Commit b0ae198113 ("security: remove unused parameter from
security_task_setscheduler()") broke the build of
arch/mips/kernel/mips-mt-fpaff.c. The function arguments were
unnecessary, not the semicolon ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
Add the ability to enable CONFIG_OF on the MIPS architecture.
Signed-off-by: Dezhong Diao <dediao@cisco.com>
[grant.likely@secretlab.ca: cleared out obsolete hooks,
removed ARCH_HAS_DEVTREE_MEM,
remove __init tags from header file,
removed debugfs support hunk]
[ddaney@linux-mips.org: backed out over aggressive trimming of hooks]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
All security modules shouldn't change sched_param parameter of
security_task_setscheduler(). This is not only meaningless, but also
make a harmful result if caller pass a static variable.
This patch remove policy and sched_param parameter from
security_task_setscheduler() becuase none of security module is
using it.
Cc: James Morris <jmorris@namei.org>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
MAINTAINERS: Change list for ioc_serial to linux-serial.
SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
MIPS: jz4740: Fix Kbuild Platform file.
MIPS: Repair Kbuild make clean breakage.
[Ralf: Michel's original patch only fixed N32; I replicated the same fix
for O32.]
Signed-off-by: Michel Thebeau <michel.thebeau@windriver.com>
Cc: paul.gortmaker@windriver.com
Cc: bruce.ashfield@windriver.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
Put the original syscall number into ->regs[0] when we leave syscall
with error. Use it in restart logics. Everything else will have
it 0 since we pass through SAVE_SOME on all the ways in. Note that
in places like bad_stack and inllegal_syscall we leave it 0 - it's not
restartable.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
To: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1539/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
debug_core,kdb: fix crash when arch does not have single step
kgdb,x86: use macro HBP_NUM to replace magic number 4
kgdb,mips: remove unused kgdb_cpu_doing_single_step operations
mm,kdb,kgdb: Add a debug reference for the kdb kmap usage
KGDB: Remove set but unused newPC
ftrace,kdb: Allow dumping a specific cpu's buffer with ftdump
ftrace,kdb: Extend kdb to be able to dump the ftrace buffer
kgdb,powerpc: Replace hardcoded offset by BREAK_INSTR_SIZE
arm,kgdb: Add ability to trap into debugger on notify_die
gdbstub: do not directly use dbg_reg_def[] in gdb_cmd_reg_set()
gdbstub: Implement gdbserial 'p' and 'P' packets
kgdb,arm: Individual register get/set for arm
kgdb,mips: Individual register get/set for mips
kgdb,x86: Individual register get/set for x86
kgdb,kdb: individual register set and and get API
gdbstub: Optimize kgdb's "thread:" response for the gdb serial protocol
kgdb: remove custom hex_to_bin()implementation
The mips kgdb specific code does not support software or HW single
stepping so it should not implement
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Implement the ability to individually get and set registers for kdb
and kgdb for mips.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
The sixth argument of notify_die() is a signal number, the fifth is a
trap number.
Instead of passing a signal number in a randomly selected argument,
pass it in the sixth. Extract the exception code from regs and pass
that as the trap number.
Get rid of redundant cast, and remove some gratuitous spaces.
Nobody actually does anything with the signal number or trap number,
but we might as well populate them with sensible values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1532/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
