Adding support for SRGGB8 is as simple as adding a new entry at
struct em28xx_fmt.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CbYCrY has been identified by looking into the tvp5150 driver and the
saa7115 datasheet.
YUV formats have been verified with em2765 + ov2640 (VAD Laplace webcam).
RGB8 formats have been verified with em2710/em2820 + mt9v011 (Silvercrest
webcam 1.3mpix).
I also did some cross-checking with these two camera devices and 0x08-0x0b
are at least 16 bits per pixel formats on em2710/em2820, too, and
0x0c-0x0f are at least 8 bits per pixel formats on em2765, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With an unknown sensor, norm_maxw() and norm_maxh() return 0 as max.
height and width values, which causes a devide by zero in size_to_scale().
Of course we could use speculative default values for unknown sensors,
but the chance that the device works at this resolution without any
driver/setup is very low and therefore not worth the efforts.
Instead, just don't treat the device as camera.
A message will then be printed to the log that the device isn't supported.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With MEDIA_SUBDRV_AUTOSELECT enabled in the kernel config, the em28xx
driver currently does't select some used subdrivers.
Fix this by adding the missing auto-selections to the Kconfig file.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2 dummy clock has been added with commit fc5d0f8a88
("V4L2: em28xx: register a V4L2 clock source") to be able to use the ov2640
soc_camera driver.
Since commit 46796cfcd3 ("ov2640: use standard clk and enable it") it is
no longer required.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use i2c_smbus_read_word_data() instead of i2c_master_send() and
i2c_master_recv() for reading the ID of Micorn sensors.
i2c_smbus_read_word_data() assumes that byes are in little-endian,
so, it uses:
data->word = msgbuf1[0] | (msgbuf1[1] << 8);
However, Micron datasheet describes the ID as if they were read
in big-endian. So, we need to change the byte order in order to
match the ID number as described on their datasheets.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new usbid eb1a:5051 for the Ion Video 2 PC MKII, Startech svid2usb23
and Raygo R12-41373.
Signed-off-by: Alexandre-Xavier Labonté-Lamoureux <alexandrexavier@live.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'usb_free_urb(urb)' is a no-op, because urb is known to be NULL.
It is likelly that releasing resources allocated by
'tm6000_alloc_urb_buffers()' just a few lines above is expected here.
This has been spotted by the following coccinelle script:
@@
expression ret, x, e;
identifier f;
@@
* if (x == NULL)
{
... when != x = e;
(
* f(<+...x...+>);
|
* ret = f(<+...x...+>);
)
...
}
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dvb-usb-dibusb-mc-common is licensed under GPLv2, and if we don't say
so then it won't even load since it needs a GPL-only symbol.
Fixes: e91455a149 ("[media] dvb-usb: split out common parts of dibusb")
Reported-by: Dominique Dumont <dod@debian.org>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for Intel SR300 depth camera in uvc driver.
This includes adding three uvc GUIDs for the required pixel formats
and updating the uvc driver GUID-to-4cc tables with the new formats.
Signed-off-by: Daniel Patrick Johnson <teknotus@teknot.us>
Signed-off-by: Aviv Greenberg <avivgr@gmail.com>
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The statistics function subtracts two timespecs manually. A helper is
provided by the kernel to do this.
Replace the implementation, using the helper.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The frame counters are inadvertently counting packets with content as
empty.
Fix it by correcting the logic expression
Fixes: 7bc5edb00b [media] uvcvideo: Extract video stream statistics
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to release the snd_card also on a late allocation error.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 2a9f8b5d25 ("V4L/DVB (5206): Usbvision: set alternate interface
modification")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Cc: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c4018fa2e4 ("[media] dib0700: fix RC support on Hauppauge
Nova-TD")
Cc: stable <stable@vger.kernel.org> # 3.16
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check for ret being non-zero is false as ret is always
zero, hence we have redundant dead code that can be removed.
Detected with CoverityScan, CID#112968 ("Constant' variable guards
dead code (DEADCODE)'")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid accessing memory
beyond the endpoint array should a device lack the expected endpoints.
Note that, as far as I can tell, the gspca framework has already made
sure there is at least one endpoint in the current alternate setting so
there should be no risk for a NULL-pointer dereference here.
Fixes: b517af7228 ("V4L/DVB: gspca_konica: New gspca subdriver for
konica chipset using cams")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY4ZYkAAoJEHm+PkMAQRiGsq4H/R4PMXDoe2XhSSk7IoT97pXV
/A8np/scAPjzEgYUidbb54OSqWwsPRuPGWONTFeSrE2u0L4wln/REI91jg7QetLq
IisncExlYeJ/XQ+iO0ZZh9fLbqwIlEJFdSXmyIFr3m/TBxe8a61C8j93oNgM1tHT
yuwzlq7c3sLq2hsmUG2HyL2kJsEfRasv4Rk0yhFuti12zVsBoTW4qmZuMauq+gdf
f7cSYgiHhPTdb2o+azg5O7uYNHaQQBxdUMlIuhhYtVOUq+pFDO23SLHSFIW2NwOm
Zn5R6CFSrLsCw0Bx0v8Xlc151QUbaRK4h9lhUhkBr6d3uNShU1NQ9JojpSvYwBo=
=vP6E
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rc5' into patchwork
Linux 4.11-rc5
* tag 'v4.11-rc5': (1168 commits)
Linux 4.11-rc5
tty: pl011: fix earlycon work-around for QDF2400 erratum 44
kasan: do not sanitize kexec purgatory
drivers/rapidio/devices/tsi721.c: make module parameter variable name unique
mm/hugetlb.c: don't call region_abort if region_chg fails
kasan: report only the first error by default
hugetlbfs: initialize shared policy as part of inode allocation
mm: fix section name for .data..ro_after_init
mm, hugetlb: use pte_present() instead of pmd_present() in follow_huge_pmd()
mm: workingset: fix premature shadow node shrinking with cgroups
mm: rmap: fix huge file mmap accounting in the memcg stats
mm: move mm_percpu_wq initialization earlier
mm: migrate: fix remove_migration_pte() for ksm pages
nfs: flexfiles: fix kernel OOPS if MDS returns unsupported DS type
NFSv4.1 fix infinite loop on IO BAD_STATEID error
serial: 8250_EXAR: fix duplicate Kconfig text and add missing help text
tty/serial: atmel: fix TX path in atmel_console_write()
tty/serial: atmel: fix race condition (TX+DMA)
serial: mxs-auart: Fix baudrate calculation
irqchip/mips-gic: Fix Local compare interrupt
...
-----BEGIN PGP SIGNATURE-----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=xT1A
-----END PGP SIGNATURE-----
Merge tag 'media/v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb-usb-firmware: don't do DMA on stack
- coda/imx-vdoa: platform_driver should not be const
- bdisp: Clean up file handle in open() error path
- exynos-gsc: Do not swap cb/cr for semi planar formats
* tag 'media/v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] exynos-gsc: Do not swap cb/cr for semi planar formats
[media] bdisp: Clean up file handle in open() error path
[media] coda/imx-vdoa: platform_driver should not be const
[media] dvb-usb-firmware: don't do DMA on stack
Adjust the keymap to use the correct nec scancodes, and adjust the
rc driver to output the correct nec scancodes.
Now the keymap can be used with any nec receiver, and the rc device
should work with any nec keymap.
Tested-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's no longer necessary to keep the i2c_client in the device struct
unmodified until a sensor is found, so reduce stack usage in
em28xx_probe_sensor_micron() and em28xx_probe_sensor_omnivision() by using
a pointer to the client instead of a local copy.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We already check for the V4L2_EVENT_CTRL inside
v4l2_ctrl_subscribe_event() so just move this function to the default:
branch of the switch and let it does the job for us.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=Liea
-----END PGP SIGNATURE-----
Merge tag 'media/v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Media regression fixes:
- serial_ir: fix a Kernel crash during boot on Kernel 4.11-rc1, due
to an IRQ code called too early
- other IR regression fixes at lirc and at the raw IR decoding
- a deadlock fix at the RC nuvoton driver
- fix another issue with DMA on stack at dw2102 driver
There's an extra patch there that change a driver interface for the
SoC VSP1 driver, with is shared between the DRM and V4L2 driver. The
patch itself is trivial, and was acked by David Arlie"
* tag 'media/v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: vsp1: Adapt vsp1_du_setup_lif() interface to use a structure
[media] dw2102: don't do DMA on stack
[media] rc: protocol is not set on register for raw IR devices
[media] rc: raw decoder for keymap protocol is not loaded on register
[media] rc: nuvoton: fix deadlock in nvt_write_wakeup_codes
[media] lirc: fix dead lock between open and wakeup_filter
[media] serial_ir: ensure we're ready to receive interrupts
The buffer allocation for the firmware data was changed in
commit 43fab9793c ("[media] dvb-usb: don't use stack for firmware load")
but the same applies for the reset value.
Fixes: 43fab9793c ("[media] dvb-usb: don't use stack for firmware load")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Kernel 4.9, WARNINGs about doing DMA on stack are hit at
the dw2102 driver: one in su3000_power_ctrl() and the other in tt_s2_4600_frontend_attach().
Both were due to the use of buffers on the stack as parameters to
dvb_usb_generic_rw() and the resulting attempt to do DMA with them.
The device was non-functional as a result.
So, switch this driver over to use a buffer within the device state
structure, as has been done with other DVB-USB drivers.
Tested with TechnoTrend TT-connect S2-4600.
[mchehab@osg.samsung.com: fixed a warning at su3000_i2c_transfer() that
state var were dereferenced before check 'd']
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The buffer allocation for the firmware data was changed in
commit 43fab9793c ("[media] dvb-usb: don't use stack for firmware load")
but the same applies for the reset value.
Fixes: 43fab9793c ("[media] dvb-usb: don't use stack for firmware load")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tveeprom_hauppauge_analog() used to need the I2C adapter in
order to print debug messages. As it now uses pr_foo() facilities
since commit 6037b3ca28 ("[media] tveeprom: print log messages
using pr_foo()"), the first argument of the function is not
needed anymore.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mxl111sf uses a lot of kernel stack memory as it puts an i2c_client
structure on the stack:
drivers/media/usb/dvb-usb-v2/mxl111sf.c: In function 'mxl111sf_init':
drivers/media/usb/dvb-usb-v2/mxl111sf.c:953:1: error: the frame size of 1248 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
We can avoid doing this by open-coding the call to i2c_transfer()
instead of calling tveeprom_read(), and not passing an i2c_client
pointer to tveeprom_hauppauge_analog(), which would ignore that
anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx231xx_do_i2c_scan function needs a lot of stack because
it puts an i2c_client structure on it:
drivers/media/usb/cx231xx/cx231xx-i2c.c: In function 'cx231xx_do_i2c_scan':
drivers/media/usb/cx231xx/cx231xx-i2c.c:518:1: error: the frame size of 1248 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
This changes it to call i2c_transfer() directly instead, avoiding the
need for the structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver uses a relatively large data structure on the stack, which
showed up on my radar as we get a warning with the "latent entropy"
GCC plugin:
drivers/media/usb/pvrusb2/pvrusb2-eeprom.c:153:1: error: the frame size of 1376 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
The warning is usually hidden as we raise the warning limit to 2048
when the plugin is enabled, but I'd like to lower that again in the
future, and making this function smaller helps to do that without
build regressions.
Further analysis shows that putting an 'i2c_client' structure on
the stack is not really supported, as the embedded 'struct device'
is not initialized here, and we are only saved by the fact that
the function that is called here does not use the pointer at all.
Fixes: d855497edb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
neded||needed
While we are here, fix the "overriden", "wont", and "etc" in the same
hunk in drivers/media/usb/tm6000/tm6000-input.c.
Link: http://lkml.kernel.org/r/1481573103-11329-14-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYqh1gAAoJEHm+PkMAQRiGMlYH/A1GkDfcx5wmdc6wuMit2vim
O/8aGsq2m+TyfjNmMR51nXroZaziW/zTtOyiBgaEEK9HAuEJhd1omq6TvLbeIoF2
QBQKUsu06jsxtYazm91XOCHBHy0uKunkSsv+NmAWBOGVtkja3pzn+qAFsfqNAx5Y
CTwNR1/fasA8OgXMRyhC3dcatY2iwXkVZ7BSut0Umcug3D69V8GbCDjqZg5hmlD2
v8yk7i58CtKezKK9pBHAE5qQyFTl5T77paLB49sLZ9PQU33uafSOm8spxzO4Z1Is
8QyHyUtdcJStRCPeOgOlFGjB+WpOKHXDA1LjshhC0P9U6AmU+hR0X5wSx8dp1s4=
=Tjmr
-----END PGP SIGNATURE-----
Merge tag 'v4.10' into patchwork
Linux 4.10
* tag 'v4.10': (1558 commits)
Linux 4.10
Fix missing sanity check in /dev/sg
scsi: don't BUG_ON() empty DMA transfers
ipv6: release dst on error in ip6_dst_lookup_tail
printk: use rcuidle console tracepoint
ARM: multi_v7_defconfig: enable Qualcomm RPMCC
irda: Fix lockdep annotations in hashbin_delete().
vxlan: fix oops in dev_fill_metadata_dst
dccp: fix freeing skb too early for IPV6_RECVPKTINFO
dpaa_eth: small leak on error
packet: Do not call fanout_release from atomic contexts
reset: fix shared reset triggered_count decrement on error
ntb: ntb_hw_intel: link_poll isn't clearing the pending status properly
ntb_transport: Pick an unused queue
ntb: ntb_perf missing dmaengine_unmap_put
NTB: ntb_transport: fix debugfs_remove_recursive
Revert "nohz: Fix collision between tick and other hrtimers"
vfs: fix uninitialized flags in splice_to_pipe()
drm/radeon: Use mode h/vdisplay fields to hide out of bounds HW cursor
ARM: 8658/1: uaccess: fix zeroing of 64-bit get_user()
...
-----BEGIN PGP SIGNATURE-----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=aXBS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A regression fix that makes the Siano driver to work again after the
CONFIG_VMAP_STACK change"
* tag 'media/v4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] siano: make it work again with CONFIG_VMAP_STACK
Reported as a Kaffeine bug:
https://bugs.kde.org/show_bug.cgi?id=375811
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.
Tested with USB ID 2040:5510: Hauppauge Windham
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the USB driver is enabled but the demodulator is not, we get a link error:
ERROR: "zd1301_demod_get_dvb_frontend" [drivers/media/usb/dvb-usb-v2/zd1301.ko] undefined!
ERROR: "zd1301_demod_get_i2c_adapter" [drivers/media/usb/dvb-usb-v2/zd1301.ko] undefined!
Such a configuration obviously makes no sense, but we should not fail
the build. This tries to mimic what we have for other drivers by turning
the build failure into a runtime failure.
Alternatively we could use an unconditional 'select' or 'depends on' to enforce
a sane configuration.
Fixes: 47d65372b3 ("[media] zd1301_demod: ZyDAS ZD1301 DVB-T demodulator driver")
Fixes: 992b39872b ("[media] zd1301: ZyDAS ZD1301 DVB USB interface driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 17ce039b4e ("[media] cxusb: don't do DMA on stack")
added a kmalloc'ed bounce buffer for writes, but missed to do the same
for reads. As the read only happens after the write is finished, we can
reuse the same buffer.
As dvb_usb_generic_rw handles a read length of 0 by itself, avoid calling
it using the dvb_usb_generic_read wrapper function.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I ran into a stack frame size warning because of the on-stack copy of
the USB device structure:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_disconnect':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:1029:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Copying a device structure like this is wrong for a number of other reasons
too aside from the possible stack overflow. One of them is that the
dev_info() call will print the name of the device later, but AFAICT
we have only copied a pointer to the name earlier and the actual name
has been freed by the time it gets printed.
This removes the on-stack copy of the device and instead copies the
device name using kstrdup(). I'm ignoring the possible failure here
as both printk() and kfree() are able to deal with NULL pointers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adding Hama Hybrid DVB-T Stick support. Technically it's the same
device what Terratec Cinergy HT USB XE is.
Signed-off-by: Piotr Oleszczyk <piotr.oleszczyk@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal Master 3 Bus can send and receive only 4 bytes per time.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
