This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mapping for LINK_MD register to enable cable testing functionality.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phylink support to the ksz8795 driver to provide
configuration exceptions on quirky KSZ8863 and KSZ8873 ports.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC treats 2500base-x same as SGMII (yay for that) except that it
must be set to a different speed.
Extend all places that check for SGMII to also check for 2500base-x.
Also add the missing 2500base-x compatibility matrix entry for SJA1110D.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the xMII Mode Parameters Table to be properly configured for SGMII
mode on SJA1110, we need to set the "special" bit, since SGMII is
officially bitwise coded as 0b0011 in SJA1105 (decimal 3, equal to
XMII_MODE_SGMII), and as 0b1011 in SJA1110 (decimal 11).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the SJA1110, the PCS of each SERDES-capable port is accessed through
a different memory window which is 0x100 bytes in size, denoted by
"pcs_base".
In each PCS register access window, the XPCS MMDs are accessed in an
indirect way: in pages/banks of up to 0x100 addresses each. Changing the
page/bank is done by writing to a special register at the end of the
access window.
The MDIO register map accessed indirectly through the indirect banked
method described above is similar to what SJA1105 has: upper 5 bits are
the MMD, lower 16 bits are the MDIO address within that MMD.
Since the PHY ID reported by the XPCS inside SJA1110 is also all zeroes
(like SJA1105), we need to trap those reads and return a fake PHY ID so
that the xpcs driver can apply some specific fixups for our integration.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire to use the generic driver for the Synopsys XPCS
located in drivers/net/pcs, and to achieve that, the sja1105 driver must
expose an MDIO bus for the SGMII PCS, because the XPCS probes as an
mdio_device.
In preparation of the SJA1110 which in fact has a different access
procedure for the SJA1105, we register this PCS MDIO bus once in the
common code, but we implement function pointers for the read and write
methods. In this patch there is a single implementation for them.
There is exactly one MDIO bus for the PCS, this will contain all PCSes
at MDIO addresses equal to the port number.
We delete a bunch of hardware support code because the xpcs driver
already does what we need.
We need to hack up the MDIO reads for the PHY ID, since our XPCS
instantiation returns zeroes and there are some specific fixups which
need to be applied by the xpcs driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamping procedure for SJA1105 is a bit unconventional
because the transmit procedure itself is unconventional.
Control packets (and therefore PTP as well) are transmitted to a
specific port in SJA1105 using "management routes" which must be written
over SPI to the switch. These are one-shot rules that match by
destination MAC address on traffic coming from the CPU port, and select
the precise destination port for that packet. So to transmit a packet
from NET_TX softirq context, we actually need to defer to a process
context so that we can perform that SPI write before we send the packet.
The DSA master dev_queue_xmit() runs in process context, and we poll
until the switch confirms it took the TX timestamp, then we annotate the
skb clone with that TX timestamp. This is why the sja1105 driver does
not need an skb queue for TX timestamping.
But the SJA1110 is a bit (not much!) more conventional, and you can
request 2-step TX timestamping through the DSA header, as well as give
the switch a cookie (timestamp ID) which it will give back to you when
it has the timestamp. So now we do need a queue for keeping the skb
clones until their TX timestamps become available.
The interesting part is that the metadata frames from SJA1105 haven't
disappeared completely. On SJA1105 they were used as follow-ups which
contained RX timestamps, but on SJA1110 they are actually TX completion
packets, which contain a variable (up to 32) array of timestamps.
Why an array? Because:
- not only is the TX timestamp on the egress port being communicated,
but also the RX timestamp on the CPU port. Nice, but we don't care
about that, so we ignore it.
- because a packet could be multicast to multiple egress ports, each
port takes its own timestamp, and the TX completion packet contains
the individual timestamps on each port.
This is unconventional because switches typically have a timestamping
FIFO and raise an interrupt, but this one doesn't. So the tagger needs
to detect and parse meta frames, and call into the main switch driver,
which pairs the timestamps with the skbs in the TX timestamping queue
which are waiting for one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is really easy, since the full RX timestamp is in the DSA trailer
and the tagger code transfers it to SJA1105_SKB_CB(skb)->tstamp, we just
need to move it to the skb shared info region. This is as opposed to
SJA1105, where the RX timestamp was received in a meta frame (so there
needed to be a state machine to pair the 2 packets) and the timestamp
was partial (so the packet, once matched with its timestamp, needed to
be added to an RX timestamping queue where the PTP aux worker would
reconstruct that timestamp).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has improved a few things compared to SJA1105:
- To send a control packet from the host port with SJA1105, one needed
to program a one-shot "management route" over SPI. This is no longer
true with SJA1110, you can actually send "in-band control extensions"
in the packets sent by DSA, these are in fact DSA tags which contain
the destination port and switch ID.
- When receiving a control packet from the switch with SJA1105, the
source port and switch ID were written in bytes 3 and 4 of the
destination MAC address of the frame (which was a very poor shot at a
DSA header). If the control packet also had an RX timestamp, that
timestamp was sent in an actual follow-up packet, so there were
reordering concerns on multi-core/multi-queue DSA masters, where the
metadata frame with the RX timestamp might get processed before the
actual packet to which that timestamp belonged (there is no way to
pair a packet to its timestamp other than the order in which they were
received). On SJA1110, this is no longer true, control packets have
the source port, switch ID and timestamp all in the DSA tags.
- Timestamps from the switch were partial: to get a 64-bit timestamp as
required by PTP stacks, one would need to take the partial 24-bit or
32-bit timestamp from the packet, then read the current PTP time very
quickly, and then patch in the high bits of the current PTP time into
the captured partial timestamp, to reconstruct what the full 64-bit
timestamp must have been. That is awful because packet processing is
done in NAPI context, but reading the current PTP time is done over
SPI and therefore needs sleepable context.
But it also aggravated a few things:
- Not only is there a DSA header in SJA1110, but there is a DSA trailer
in fact, too. So DSA needs to be extended to support taggers which
have both a header and a trailer. Very unconventional - my understanding
is that the trailer exists because the timestamps couldn't be prepared
in time for putting them in the header area.
- Like SJA1105, not all packets sent to the CPU have the DSA tag added
to them, only control packets do:
* the ones which match the destination MAC filters/traps in
MAC_FLTRES1 and MAC_FLTRES0
* the ones which match FDB entries which have TRAP or TAKETS bits set
So we could in theory hack something up to request the switch to take
timestamps for all packets that reach the CPU, and those would be
DSA-tagged and contain the source port / switch ID by virtue of the
fact that there needs to be a timestamp trailer provided. BUT:
- The SJA1110 does not parse its own DSA tags in a way that is useful
for routing in cross-chip topologies, a la Marvell. And the sja1105
driver already supports cross-chip bridging from the SJA1105 days.
It does that by automatically setting up the DSA links as VLAN trunks
which contain all the necessary tag_8021q RX VLANs that must be
communicated between the switches that span the same bridge. So when
using tag_8021q on sja1105, it is possible to have 2 switches with
ports sw0p0, sw0p1, sw1p0, sw1p1, and 2 VLAN-unaware bridges br0 and
br1, and br0 can take sw0p0 and sw1p0, and br1 can take sw0p1 and
sw1p1, and forwarding will happen according to the expected rules of
the Linux bridge.
We like that, and we don't want that to go away, so as a matter of
fact, the SJA1110 tagger still needs to support tag_8021q.
So the sja1110 tagger is a hybrid between tag_8021q for data packets,
and the native hardware support for control packets.
On RX, packets have a 13-byte trailer if they contain an RX timestamp.
That trailer is padded in such a way that its byte 8 (the start of the
"residence time" field - not parsed by Linux because we don't care) is
aligned on a 16 byte boundary. So the padding has a variable length
between 0 and 15 bytes. The DSA header contains the offset of the
beginning of the padding relative to the beginning of the frame (and the
end of the padding is obviously the end of the packet minus 13 bytes,
the length of the trailer). So we discard it.
Packets which don't have a trailer contain the source port and switch ID
information in the header (they are "trap-to-host" packets). Packets
which have a trailer contain the source port and switch ID in the trailer.
On TX, the destination port mask and switch ID is always in the trailer,
so we always need to say in the header that a trailer is present.
The header needs a custom EtherType and this was chosen as 0xdadc, after
0xdada which is for Marvell and 0xdadb which is for VLANs in
VLAN-unaware mode on SJA1105 (and SJA1110 in fact too).
Because we use tag_8021q in concert with the native tagging protocol,
control packets will have 2 DSA tags.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105, RX timestamps for packets sent to the CPU are transmitted in
separate follow-up packets (metadata frames). These contain partial
timestamps (24 or 32 bits) which are kept in SJA1105_SKB_CB(skb)->meta_tstamp.
Thankfully, SJA1110 improved that, and the RX timestamps are now
transmitted in-band with the actual packet, in the timestamp trailer.
The RX timestamps are now full-width 64 bits.
Because we process the RX DSA tags in the rcv() method in the tagger,
but we would like to preserve the DSA code structure in that we populate
the skb timestamp in the port_rxtstamp() call which only happens later,
the implication is that we must somehow pass the 64-bit timestamp from
the rcv() method all the way to port_rxtstamp(). We can use the skb->cb
for that.
Rename the meta_tstamp from struct sja1105_skb_cb from "meta_tstamp" to
"tstamp", and increase its size to 64 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SJA1105, there is support for a cascade port which is presumably
connected to a downstream SJA1105 switch. The upstream one does not take
PTP timestamps for packets received on this port, presumably because the
downstream switch already did (and for PTP, it only makes sense for the
leaf nodes in a DSA switch tree to do that).
I haven't been able to validate that feature in a fully assembled setup,
so I am disabling the feature by setting the cascade port to an unused
port value (ds->num_ports).
In SJA1110, multiple cascade ports are supported, and CASC_PORT became
a bit mask from a port number. So when CASC_PORT is set to ds->num_ports
(which is 11 on SJA1110), it is actually set to 0b1011, so ports 3, 1
and 0 are configured as cascade ports and we cannot take RX timestamps
on them.
So we need to introduce a check for SJA1110 and set things differently
(to zero there), so that the cascading feature is properly disabled and
RX timestamps can be taken on all ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As opposed to SJA1105 where there are parts with TTEthernet and parts
without, in SJA1110 all parts support it, but it must be enabled in the
static config. So enable it unconditionally. We use it for the tc-taprio
and tc-gate offload.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return code variable rc is being set to return error values in two
places in sja1105_mdiobus_base_tx_register and yet it is not being
returned, the function always returns 0 instead. Fix this by replacing
the return 0 with the return code rc.
Addresses-Coverity: ("Unused value")
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code check "reg" but "ret" was intended so the error handling will
never trigger.
Fixes: 7c9896e378 ("net: dsa: qca8k: check return value of read functions correctly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hi" variable is a u64 but the qca8k_read() writes to the top 32
bits of it. That will work on little endian systems but it's a bit
subtle. It's cleaner to make declare "hi" as a u32. We will still need
to cast it when we shift it later on in the function but that's fine.
Fixes: 7c9896e378 ("net: dsa: qca8k: check return value of read functions correctly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all
VLANs") forced the CPU port to be always tagged in any VLAN membership.
This was necessary back then because we did not support Broadcom tags
for all configurations so the only way to differentiate tagged and
untagged traffic while DSA_TAG_PROTO_NONE was used was to force the CPU
port into being always tagged.
With most configurations enabling Broadcom tags, especially after
8fab459e69 ("net: dsa: b53: Enable Broadcom tags for 531x5/539x
families") we do not need to apply this unconditional force tagging of
the CPU port in all VLANs.
A helper function is introduced to faciliate the encapsulation of the
specific condition requiring the CPU port to be tagged in all VLANs and
the dsa_switch_ops::untag_bridge_pvid boolean is moved to when
dsa_switch_ops::setup is called when we have already determined the
tagging protocol we will be using.
Reported-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the static initialization done by ocelot_init_port()
which enables flow control unconditionally, set SYS_PAUSE_CFG_PAUSE_ENA
according to the parameters negotiated by the PHY.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 contains two types of integrated PHYs: one 100base-TX PHY
and multiple 100base-T1 PHYs.
The access procedure for the 100base-T1 PHYs is also different than it
is for the 100base-TX one. So we register 2 MDIO buses, one for the
base-TX and the other for the base-T1. Each bus has an OF node which is
a child of the "mdio" subnode of the switch, and they are recognized by
compatible string.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has an extra configuration in the General Parameters Table
through which the user can select the buffer reservation config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 is basically an SJA1105 with more ports, some integrated
PHYs (100base-T1 and 100base-TX) and an embedded microcontroller which
can be disabled, and the switch core can be controlled by a host running
Linux, over SPI.
This patch contains:
- the static and dynamic config packing functions, for the tables that
are common with SJA1105
- one more static config tables which is "unique" to the SJA1110
(actually it is a rehash of stuff that was placed somewhere else in
SJA1105): the PCP Remapping Table
- a reset and clock configuration procedure for the SJA1110 switch.
This resets just the switch subsystem, and gates off the clock which
powers on the embedded microcontroller.
- an RGMII delay configuration procedure for SJA1110, which is very
similar to SJA1105, but different enough for us to be unable to reuse
it (this is a pattern that repeats itself)
- some adaptations to dynamic config table entries which are no longer
programmed in the same way. For example, to delete a VLAN, you used to
write an entry through the dynamic reconfiguration interface with the
desired VLAN ID, and with the VALIDENT bit set to false. Now, the VLAN
table entries contain a TYPE_ENTRY field, which must be set to zero
(in a backwards-incompatible way) in order for the entry to be deleted,
or to some other entry for the VLAN to match "inner tagged" or "outer
tagged" packets.
- a similar thing for the static config: the xMII Mode Parameters Table
encoding for SGMII and MII (the latter just when attached to a
100base-TX PHY) just isn't what it used to be in SJA1105. They are
identical, except there is an extra "special" bit which needs to be
set. Set it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that both RevMII as well as RevRMII exist, we can deprecate the
sja1105,role-mac and sja1105,role-phy properties and simply let the user
select that a port operates in MII PHY role by using
phy-mode = "rev-mii";
or in RMII PHY role by using
phy-mode = "rev-rmii";
There are no fixed-link MII or RMII properties in mainline device trees,
and the setup itself is fairly uncommon, so there shouldn't be risks of
breaking compatibility.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has an intermediate way of determining whether the
RGMII delays should be applied by the PHY or by itself: by looking at
the port role (PHY or MAC). The port can be put in the PHY role either
explicitly (sja1105,role-phy) or implicitly (fixed-link).
We want to deprecate the sja1105,role-phy property, so all that remains
is the fixed-link property. Introduce a "fixed_link" array of booleans
in the driver, and use that to determine whether RGMII delays must be
applied or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an inbound policy filter which matches the HSR/PRP supervision
MAC range and forwards to the CPU port without discarding duplicates.
This is required to correctly populate time_in[A] and time_in[B] in the
HSR/PRP node_table. Leave the policy disabled by default and
enable/disable it when joining/leaving hsr.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1105 has a static configuration comprised of a number of tables
with entries. Some of these can be read and modified at runtime as well,
through the dynamic configuration interface.
As a careful reader can notice from the comments in this file, the
software interface for accessing a table entry through the dynamic
reconfiguration is a bit of a no man's land, and varies wildly across
switch generations and even from one kind of table to another.
I have tried my best to come up with a software representation of a
'common denominator' SPI command to access a table entry through the
dynamic configuration interface:
struct sja1105_dyn_cmd {
bool search;
u64 valid; /* must be set to 1 */
u64 rdwrset; /* 0 to read, 1 to write */
u64 errors;
u64 valident; /* 0 if entry is invalid, 1 if valid */
u64 index;
};
Relevant to this patch is the VALIDENT bit, which for READ commands is
populated by the switch and lets us know if we're looking at junk or at
a real table entry.
In SJA1105, the dynamic reconfiguration interface for management routes
has notably not implemented the VALIDENT bit, leading to a workaround to
ignore this field in sja1105_dynamic_config_read(), as it will be set to
zero, but the data is valid nonetheless.
In SJA1110, this pattern has sadly been abused to death, and while there
are many more tables which can be read back over the dynamic config
interface compared to SJA1105, their handling isn't in any way more
uniform. Generally speaking, if there is a single possible entry in a
given table, and loading that table in the static config is mandatory as
per the documentation, then the VALIDENT bit is deemed as redundant and
more than likely not implemented.
So it is time to make the workaround more official, and add a bit to the
flags implemented by dynamic config tables. It will be used by more
tables when SJA1110 support arrives.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In SJA1105, the xMII Mode Parameters Table field called PHY_MAC denotes
the 'role' of the port, be it a PHY or a MAC. This makes a difference in
the MII and RMII protocols, but RGMII is symmetric, so either PHY or MAC
settings result in the same hardware behavior.
The SJA1110 is different, and the RGMII ports only work when configured
in MAC mode, so keep the port roles in MAC mode unconditionally.
Why we had an RGMII port in the PHY role in the first place was because
we wanted to have a way in the driver to denote whether RGMII delays
should be applied based on the phy-mode property or not. This is already
done in sja1105_parse_rgmii_delays() based on an intermediary
struct sja1105_dt_port (which contains the port role). So it is a
logical fallacy to use the hardware configuration as a scratchpad for
driver data, it isn't necessary.
We can also remove the gating condition for applying RGMII delays only
for ports in the PHY role. The .setup_rgmii_delay() method looks at
the priv->rgmii_rx_delay[port] and priv->rgmii_tx_delay[port] properties
which are already populated properly (in the case of a port in the MAC
role they are false). Removing this condition generates a few more SPI
writes for these ports (clearing the RGMII delays) which are perhaps
useless for SJA1105P/Q/R/S, where we know that the delays are disabled
by default. But for SJA1110, the firmware on the embedded microcontroller
might have done something funny, so it's always a good idea to clear the
RGMII delays if that's what Linux expects.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support the new speed of 2500Mbps, the SJA1110 has achieved
the great performance of changing the encoding in the MAC Configuration
Table for the port speeds of 10, 100, 1000 compared to SJA1105.
Because this is a common driver, we need a layer of indirection in order
to program the hardware with the right values irrespective of switch
generation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the SJA1105, all ports support the parallel "xMII" protocols (MII,
RMII, RGMII) except for port 4 on SJA1105R/S which supports only SGMII.
This was relatively easy to model, by special-casing the SGMII port.
On the SJA1110, certain ports can be pinmuxed between SGMII and xMII, or
between SGMII and an internal 100base-TX PHY. This creates problems,
because the driver's assumption so far was that if a port supports
SGMII, it uses SGMII.
We allow the device tree to tell us how the port pinmuxing is done, and
check that against a PHY interface type compatibility matrix for
plausibility.
The other big change is that instead of doing SGMII configuration based
on what the port supports, we do it based on what is the configured
phy_mode of the port.
The 2500base-x support added in this patch is not complete.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we've succeeded in operating without keeping a copy of the
phy-mode in the driver, since we already have the static config and we
can look at the xMII Mode Parameters Table which already holds that
information.
But with the SJA1110, we cannot make the distinction between sgmii and
2500base-x, because to the hardware's static config, it's all SGMII.
So add a phy_mode property per port inside struct sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looking at the SGMII PCS from SJA1110, which is accessed indirectly
through a different base address as can be seen in the next patch, it
appears odd that the address accessed through indirection still
references the base address from the SJA1105S register map (first MDIO
register is at 0x1f0000), when it could index the SGMII registers
starting from zero.
Except that the 0x1f0000 is not a base address at all, it seems. It is
0x1f << 16 | 0x0000, and 0x1f is coding for the vendor-specific MMD2.
So, it turns out, the Synopsys PCS implements all its registers inside
the vendor-specific MMDs 1 and 2 (0x1e and 0x1f). This explains why the
PCS has no overlaps (for the other MMDs) with other register regions of
the switch (because no other MMDs are implemented).
Change the code to remove the SGMII "base address" and explicitly encode
the MMD for reads/writes. This will become necessary for SJA1110 support.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SJA1105 R and S switches have 1 SGMII port (port 4). Because there
is only one such port, there is no "port" parameter in the configuration
code for the SGMII PCS.
However, the SJA1110 can have up to 4 SGMII ports, each with its own
SGMII register map. So we need to generalize the logic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f2f3e09396be ("net: dsa: sja1105: be compatible with
"ethernet-ports" OF node name"), DSA supports the "ethernet-ports" name
for the container node of the ports, but the sja1105 driver doesn't,
because it handles some device tree parsing of its own.
Add the second node name as a fallback.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now we can check qca8k_read() return value correctly, so if
it fails, we need return directly.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current return type of qca8k_mii_read32() and qca8k_read() are
unsigned, it can't be negative, so the return value check is
unuseful. For check the return value correctly, change return
type of the read functions and add a output parameter to store
the read value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shared frame buffer of the SJA1110 is larger than that of SJA1105,
which is natural due to the fact that there are more ports.
Introduce yet another property in struct sja1105_info which encodes the
maximum number of 128 byte blocks that can be used for frame buffers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 policer array is similar in layout with SJA1105, except it
contains one multicast policer per port at the end.
Detect the presence of multicast policers based on the maximum number of
supported L2 Policing Table entries, and make those policers have a
shared index equal to the port's default policer. Letting the user
configure these policers is not supported at the moment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using sja1105_xfer_buf results in a higher overhead and is harder to
read.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that the port count is different, some static config
tables have a different number of elements in SJA1105 compared to
SJA1110. Such an example is the L2 Policing table, which has 45 entries
in SJA1105 (one per port x traffic class, and one broadcast policer per
port) and 110 entries in SJA1110 (one per port x traffic class, one
broadcast and one multicast policer per port).
Similarly, the MAC Configuration Table, the L2 Forwarding table, all
have a different number of elements simply because the port count is
different, and although this can be accounted for by looking at
ds->ports, the policing table can't because of the presence of the extra
multicast policers.
The common denominator for the static config initializers for these
tables is that they must set up all the entries within that table.
So the simplest way to account for these differences in a uniform manner
is to look at struct sja1105_table_ops::max_entry_count. For the sake of
uniformity, this patch makes that change also for tables whose number of
elements did not change in SJA1110, like the xMII Mode Parameters, the
L2 Lookup Parameters, General Parameters, AVB Parameters (all of these
are singleton tables with a single entry).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two distinct code paths which enter sja1105_clocking.c, one
through sja1105_clocking_setup() and the other through
sja1105_clocking_setup_port():
sja1105_static_config_reload sja1105_setup
| |
| +------------------+
| |
v v
sja1105_clocking_setup sja1105_adjust_port_config
| |
v |
sja1105_clocking_setup_port <------------------+
As opposed to SJA1105, the SJA1110 does not need any configuration of
the Clock Generation Unit in order for xMII ports to work. Just RGMII
internal delays need to be configured, and that is done inside
sja1105_clocking_setup_port for the RGMII ports.
So this patch introduces the concept of a "reserved address", which the
CGU configuration functions from sja1105_clocking.c must check before
proceeding to do anything. The SJA1110 will have reserved addresses for
the CGU PLLs for MII/RMII/RGMII.
Additionally, make sja1105_clocking_setup() a function pointer so it can
be overridden by the SJA1110. Even though nothing port-related needs to
be done in the CGU, there are some operations such as disabling the
watchdog clock which are unique to the SJA1110.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If @port is unused, then dsa_upstream_port(ds, port) returns @port,
which means we cannot assume the CPU port can be retrieved this way.
The sja1105 switches support a single CPU port, so just iterate over the
switch ports and stop at the first CPU port we see.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a SJA1105_MAX_NUM_PORTS macro which at the moment is equal to
SJA1105_NUM_PORTS (5). With the introduction of SJA1110, these
structures will need to hold information for up to 11 ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not put unused ports in the forwarding domain, and do not allocate
FDB entries for dynamic address learning for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver will gain support for the next-gen SJA1110 switch,
which is very similar except for the fact it has more than 5 ports.
So we need to replace the hardcoded SJA1105_NUM_PORTS in this driver
with ds->num_ports. This patch is as mechanical as possible (save for
the fact that ds->num_ports is not an integer constant expression).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp4 master br0
bridge vlan add dev swp4 vid 1
We observe the traffic sent on swp4 is still untagged, even though the
bridge has overwritten the existing VLAN entry:
port vlan ids
swp4 1 PVID
br0 1 PVID Egress Untagged
This happens because we didn't consider that the 'bridge vlan add'
command just overwrites VLANs like it's nothing. We treat the 'vid 1
pvid untagged' and the 'vid 1' as two separate VLANs, and the first
still has precedence when calling sja1105_build_vlan_table. Obviously
there is a disagreement regarding semantics, and we end up doing
something unexpected from the PoV of the bridge.
Let's actually consider an "existing VLAN" to be one which is on the
same port, and has the same VLAN ID, as one we already have, and update
it if it has different flags than we do.
The first blamed commit is the one introducing the bug, the second one
is the latest on top of which the bugfix still applies.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Fixes: 5899ee367a ("net: dsa: tag_8021q: add a context structure")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
