This reverts commit 38aecea0cc.
This breaks Haswell Thinkpad + Lenovo dock in SST mode with a HDMI monitor attached.
Before this we can 1920x1200 mode, after this we only ever get 1024x768, and
a lot of deferring.
This didn't revert clean, but this should be fine.
bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1117008
Cc: stable@vger.kernel.org # v3.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 98ec77397a
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Apr 30 17:43:01 2014 +0300
drm/i915: Make primary_enabled match the actual hardware state
introduced more accurate tracking of the primary plane and some
checks. It missed the plane->pipe reassignement code for gen2/3
though, which the checks caught and resulted in WARNING backtraces.
Since we only use this path if the plane is on and on the wrong pipe
we can just always set the tracking bit to "enabled".
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
drm/i915: do not setup backlight if not available according to VBT
caused a regression on the HP Chromebook 14 (with Celeron 2955U CPU),
which has a misconfigured VBT. Apply quirk to ignore the VBT backlight
presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Stefan Nagy <public@stefan-nagy.at>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 773875bfb6.
It is very much needed and the lack of dithering has been reported by
a large list of people with various gen2/3 hardware.
Also, the original patch was complete non-sense since the WARNING
backtraces in the references bugzilla are about
gmch_pfit.lvds_border_bits mismatch, not at all about the dither bit.
That one seems to work.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register to read cz count is different from vlv. Also
the counts returned from CCK_CTL1 for BSW are (ticks in 30ns - 1).
czcount_30ns of value 1 is a special case for 320Mhz.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80703
Suggested-by: Deepak S <deepak.s@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_rotation_simplify() can be used to eliminate unsupported rotation
flags. It will check if any unsupported flags are present, and if so
it will modify the rotation to an alternate form by adding 180 degrees
to rotation angle, and flipping the reflect x and y bits. The hope is
that this identity transform will eliminate the unsupported flags.
Of course that might not result in any more supported rotation, so
the caller is still responsible for checking the result afterwards.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some helper functions to move drm_rects between different rotated
coordinate spaces. One function does the forward transform and
another does the inverse.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new drm_mode_create_rotation_property() in omapdrm.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a function to create a standards compliant rotation property.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make drm_property_create_bitmask() a bit more generic by allowing the
caller to specify which bits are in fact supported. This allows multiple
callers to use the same enum list, but still create different versions
of the same property with different list of supported bits.
v2: Populate values[] array as non-sparse
Make supported_bits 64bit
Fix up omapdrm call site (Rob)
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rotation property stuff should be standardized among all drivers.
Move the bits to drm_crtc.h from omap_drv.h.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Register the CRTC with the port node so that the DRM OF helpers can
find the appropriate CRTC. This is important so that encoders can
identify their corresponding possible CRTCs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is useful for userspace utilities to verify and micromanaging
the increase/decrease frequncy.
v2: Use vlv_gpu_freq to get freq (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enabled PM interrupt programming for CHV. Re-using gen8 code and extending same for CHV.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding chv specific fre/encode conversion.
v2: Remove generic function and platform check (Daniel)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need mem_freq or cz clock for freq/opcode conversion
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for userspace utilities to verify and micromanaging the
increase/decrease frequncy.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reading RP1 for valleyview to help us enable "pm_rps" i-g-t testcase
execution.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Add missing static.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV and CHV disable the DP port only in the .post_disable() hook, so we
need to make intel_sanitize_encoder() call that when it's trying to
disable encoders without an active pipes.
My bsw actaully hits this when an external display is connected. The
BIOS still likes to turn on the eDP port, but leaves the pipe disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Remove now bogus comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the underscore between "clk" and "1" so that we match the name
of the clock given in the documentation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the Armada DRM driver to use the component helpers, which will
permit us to clean up the driver and move towards an implementation
which is compatible with a DT description of the hardware.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a helper to allow encoders to find their possible CRTCs from the
OF graph without having to re-implement this functionality. We add a
device_node to drm_crtc which corresponds with the port node in the
DT description of the CRTC device.
We can then scan the DRM device list for CRTCs to find their index,
matching the appropriate CRTC using the port device_node, thus building
up the possible CRTC mask.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No need to re-read the hardware rps fuses when we already have all the
values tucked away in dev_priv->rps.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
commit 62942ed727
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Jun 13 09:28:33 2014 -0700
drm/i915/vlv: disable PPGTT on early revs v3
we forgot about CHV. IS_VALLEYVIEW() is true for CHV, so we need to
explicitly avoid disabling PPGTT on CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"Nothing too scary, we have one outstanding i915 regression but Daniel
has promised the fix as soon as he's finished testing it a bit.
Fixes for the main x86 drivers:
- radeon: dpm fixes, displayport regression fix
- i915: quirks for backlight regression, edp reboot fix, valleyview
black screen fixes
- nouveau: display port regression fixes, fix for memory reclocking"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: Reenabling SS on Cayman
drm/radeon: fix typo in ci_stop_dpm()
drm/radeon: fix typo in golden register setup on evergreen
drm/radeon: only print meaningful VM faults
drm/radeon/dp: return -EIO for flags not zero case
drm/i915/vlv: T12 eDP panel timing enforcement during reboot
drm/i915: Only unbind vgacon, not other console drivers
drm/i915: Don't clobber the GTT when it's within stolen memory
drm/i915/vlv: Update the DSI ULPS entry/exit sequence
drm/i915/vlv: DPI FIFO empty check is not needed
drm/i915: Toshiba CB35 has a controllable backlight
drm/i915: Acer C720 and C720P have controllable backlights
drm/i915: quirk asserts controllable backlight presence, overriding VBT
drm/nouveau/ram: fix test for gpio presence
drm/nouveau/dp: workaround broken display
drm/nouveau/dp: fix required link bandwidth calculations
drm/nouveau/kms: restore fbcon after display has been resumed
drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
drm/nouveau/fb: Prevent inlining of ramfuc_reg
drm/gk104/ram: bash mpll bit 31 on
It reverts commit c745fe611c now that
Cayman is stable since VDDCI fix. Spread spectrum was not the culprit.
This depends on b0880e87c1
(drm/radeon/dpm: fix vddci setup typo on cayman).
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to use the RREG32_SMC() accessor since the register
is an smc indirect index.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
If there are error flags in the aux transaction return
-EIO rather than -EBUSY. -EIO restarts the whole transaction
while -EBUSY jus retries. Fixes problematic aux transfers.
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80684
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We can eliminate a lot of special case code by making the computation of
the interrupt mask be correct for all callers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Place the RPS counters inside the RPS struct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
C is super happy to asign anything pointer to void *. Don't pretend
otherwise.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may reach this point while the machine is still runtime suspended,
so we'll hit a WARN. The other encoders also don't touch registers at
this point, so instead of waking the machine up, write some code to
keep the register always at the same state, including after we runtime
suspend/resume.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we do for the other encoders. This should fix some WARNs
when running pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we already do in haswell_get_pipe_config(). This should
prevent some WARNs when we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we now have support for shared DPLLS.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be able to do this we need to separately keep track of how many
crtcs need a given WRPLL and how many actually actively use it. The
common shared dpll framework already has all this, including massive
state readout and cross checking. Which allows us to do this switch in
a fairly small patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This time around another cute hack to pre-fill the pll->hw_state with
the right values. And also remove a bunch of checks which will be
replaced by lots more checks in the common framework.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently still with a redudant WARN_ON in there, the common shared
dpll code will take care of this in the future.
Also we need to flip the switch for the transitional hack now to make
sure that we disable the right pll.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still tacked onto the side, but slowly getting there.
v2: Don't forget the debugfs file.
v3 (from Paulo): Don't forget to check the power domains.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And get/put it when needed. The special thing about this commit is
that it will now return false in ibx_pch_dpll_get_hw_state() in case
the power domain is not enabled. This will fix some WARNs we have when
we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla:https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just filing in names and ids, but not yet officially registering them
so that the hw state cross checker doesn't completely freak out about
them. Still since we do already read out and cross check
config->shared_dpll the basics are now there to flesh out the wrpll
shared dpll implementation.
The idea is now to roll out all the callbacks step-by-step and then at
the end switch to the shared dpll framework. This way hw and sw
changes are clearly separated.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: added const to hsw_ddi_pll_names (Damien)]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way only the dynamic WRPLL selection for hdmi ddi mode is
done in intel_ddi_pll_select.
v2: Don't clobber the precomputed values when selecting clocks fro
hdmi encoders.
v3 (from Paulo): Rebase on top of the s/IS_HASWELL/HAS_DDI/ patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't let it fall in the HAS_PCH_SPLIT() case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.
We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.
Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.
v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just boring sed job for preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to how the ->crtc_mode_set hook should touch the hardware to
enable anything the ->crtc_off hook should disable anything in the
hardware. Otherwise runtime pm for dpms will not work.
Currently the only things left int the haswell_crtc_off hook is
disabling the ddi plls. We can't move the WRPLL enabling out yet
because the current ddi pll sharing code used by the haswell code
doesn't separately track active users and overall users. This must be
fixed by porting it to the generic shared display pll framework, which
is powerful enough.
But the SPLL source is only used by the crt encoder and so can be
moved already. We only need to make sure that the ddi port E is
already off, which hsw_fdi_disable does by calling
intel_ddi_post_disable.
With this the code reorg to shuffle hsw fdi/lpt specific code into a
new hsw-specific crt encoder type is now finally complete.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The call to intel_ddi_pll_enable in haswell_crtc_mode_set is the only
function that still touches the hardware state from the crtc mode_set
callback on hsw. Since the SPLL isn't ever shared we can easily take
it out into the hsw crt encoder functions.
Temporarily we'll loose a bit of WARN_ON coverage with this, but once
the WRPLLs are switched over that will be restored. For the SPLL
selection add a WARN in the hsw fdi link training code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL disabling
into the post_disable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT post_disable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL enabling
into the pre_enable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT pre_enable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Luckily the bit definitions match, but it's still confusing
to use one when handling the other. So sprinkle some OCD over
the #defines to make them match and use the right version in
each place.
Maybe we should unify these definitions completely, but that
can always be done sometime in the future.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SPLL would be a reference clock we could potentially share,
especially if we want to use the SSC mode. But currently we
don't, so let's rip out this complexity for a simpler conversion
to the new display pll framework.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the other checks also check hw state, so checking our software
refcounts for the plls looks a bit odd. Also this will simplify the
conversion over to the shared dpll framework, which itself has massive
amounts of checks to make sure that we never leave a display pll
enabled when we shouldn't.
So after that conversion we should stil have a good enough coverage of
asserts for entering pc8/runtime pm on hsw/bdw.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add !mutex_is_locked() checks to intel_pin_and_fence_fb_obj() and
intel_unpin_fb_obj() to help catch failures to grab struct_mutex when
operating on fb objects.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_primary_plane_{setplane,disable} were lacking struct_mutex locking
around their GEM operations.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reported-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we will print some WARNs when we read registers and the
machine is suspended.
Testcase: igt/pm_rpm/debugfs-read
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.
With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That function can be used to write anything on D_COMP, not just
disable it, so print a more appropriate message.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 34ea3d3863 ("drm: add register and unregister functions
for connectors") probably missed out converting the
drm_sysfs_connector_remove instances in the following files.
Without this patch we get the following compilation error:
ERROR: "drm_sysfs_connector_remove" [drivers/gpu/drm/tilcdc/tilcdc.ko] undefined!
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
CC: Thomas Wood <thomas.wood@intel.com>
CC: David Herrmann <dh.herrmann@gmail.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes for regressions and black screens, cc: stable where applicapable
(the last minute rebase was to sprinkle missing stable tags). A bit more
than what I'd wish for, but excluding vlv and that the first 3 patches are
just quirks for 1 regression it looks much better.
There's still a "oops, lost dithering" issue on older platforms open. I'm
working on a fix for that now but didn't want to delay this pile.
* tag 'drm-intel-fixes-2014-07-09' of git://anongit.freedesktop.org/drm-intel:
drm/i915/vlv: T12 eDP panel timing enforcement during reboot
drm/i915: Only unbind vgacon, not other console drivers
drm/i915: Don't clobber the GTT when it's within stolen memory
drm/i915/vlv: Update the DSI ULPS entry/exit sequence
drm/i915/vlv: DPI FIFO empty check is not needed
drm/i915: Toshiba CB35 has a controllable backlight
drm/i915: Acer C720 and C720P have controllable backlights
drm/i915: quirk asserts controllable backlight presence, overriding VBT
A couple of DP regression fixes, kepler memory reclocking fixes, and a fix for an annoying display issue that can pop up on resume.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ram: fix test for gpio presence
drm/nouveau/dp: workaround broken display
drm/nouveau/dp: fix required link bandwidth calculations
drm/nouveau/kms: restore fbcon after display has been resumed
drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
drm/nouveau/fb: Prevent inlining of ramfuc_reg
drm/gk104/ram: bash mpll bit 31 on
CHV hard hangs on reading on 0x11100
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading on 0x112f4.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading these registers. As these have not
been used since cantiga & ilk, remove the debugfs entry.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading these registers. As these have not
been used since cantiga & ilk, remove the debugfs entry.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.
Potential uses of this macro were identified via the following
Coccinelle patch:
@@
expression E;
@@
* to_intel_framebuffer(E)->obj
@@
expression E;
identifier I;
@@
I = to_intel_framebuffer(E);
...
* I->obj
v2: Rewrite some NULL tests in terms of the obj rather than the fb.
Also add a WARN() if trying to pageflip with a disabled primary
plane. [Suggested by Chris Wilson]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an intel_fb_obj() macro that returns the GEM object associated with
a DRM framebuffer. This macro is safe to call on NULL framebuffers (a
NULL object pointer will be returned in this case).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The console subsystem only provides a function to switch to a given
console, but we want to actually only switach away from vgacon.
Unconditionally switching to the dummy console resulted in switching
away from fbcon in multi-gpu setups when other gpu drivers are loaded
before i915.
Then either the reinitialization of fbcon when i915 registers its
fbdev emulation or the teardown of the fbcon driver killed the
machine. So only switch to the dummy console when it's required.
Kudos to Chris for the original idea, I've only refined it a bit to
still unregister vgacon even when it's currently unused.
This regression has been introduced in
commit a4de05268e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 5 16:20:46 2014 +0200
drm/i915: Kick out vga console
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On most gen2-4 platforms the GTT can be (or maybe always is?)
inside the stolen memory region. If that's the case, reduce the
size of the stolen memory appropriately to make make sure we
don't clobber the GTT.
v2: Deal with gen4 36 bit physical address
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80151
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should keep DEVICE_READY bit set in the ULPS enter sequence. In
exit sequence also we should set DEVICE_READY, but thats causing
blankout for me. Also exit sequence is simplified as per hw team
recommendation.
This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While sending DPI SHUTDOWN command, we cannot wait for FIFO empty as
pipes are not disabled at that time. In case of MIPI we disable port
first and send SHUTDOWN command while pipe is still running and FIFOs
will not be empty, causing spurious error log
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The Toshiba CB35 Chromebook (with Celeron 2955U CPU) has a controllable
backlight although its VBT reports otherwise. Apply quirk to ignore the
backlight presence check during backlight setup.
Patch tested by author on Toshiba CB35.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Acer C720 and C720P Chromebooks (with Celeron 2955U CPU) have a
controllable backlight although their VBT reports otherwise. Apply quirk
to ignore the backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Accurate frontbuffer tracking and frontbuffer rendering invalidate, flush and
flip events. This is prep work for proper PSR support and should also be
useful for DRRS&fbc.
- Runtime suspend hardware on system suspend to support the new SOix sleep
states, from Jesse.
- PSR updates for broadwell (Rodrigo)
- Universal plane support for cursors (Matt Roper), including core drm patches.
- Prefault gtt mappings (Chris)
- baytrail write-enable pte bit support (Akash Goel)
- mmio based flips (Sourab Gupta) instead of blitter ring flips
- interrupt handling race fixes (Oscar Mateo)
And old, not yet merged features from the previous round:
- rps/turbo support for chv (Deepak)
- some other straggling chv patches (Ville)
- proper universal plane conversion for the primary plane (Matt Roper)
- ppgtt on vlv from Jesse
- pile of cleanups, little fixes for insane corner cases and improved debug
support all over
* tag 'drm-intel-next-2014-06-20' of git://anongit.freedesktop.org/drm-intel: (99 commits)
drm/i915: Update DRIVER_DATE to 20140620
drivers/i915: Fix unnoticed failure of init_ring_common()
drm/i915: Track frontbuffer invalidation/flushing
drm/i915: Use new frontbuffer bits to increase pll clock
drm/i915: don't take runtime PM reference around freeze/thaw
drm/i915: use runtime irq suspend/resume in freeze/thaw
drm/i915: Properly track domain of the fbcon fb
drm/i915: Print obj->frontbuffer_bits in debugfs output
drm/i915: Introduce accurate frontbuffer tracking
drm/i915: Drop schedule_back from psr_exit
drm/i915: Ditch intel_edp_psr_update
drm/i915: Drop unecessary complexity from psr_inactivate
drm/i915: Remove ctx->last_ring
drm/i915/chv: Ack interrupts before handling them (CHV)
drm/i915/bdw: Ack interrupts before handling them (GEN8)
drm/i915/vlv: Ack interrupts before handling them (VLV)
drm/i915: Ack interrupts before handling them (GEN5 - GEN7)
drm/i915: Don't BUG_ON in i915_gem_obj_offset
drm/i915: Grab dev->struct_mutex in i915_gem_pageflip_info
drm/i915: Add some L3 registers to the parser whitelist
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
On g33, the documentation states
"HWS_PGA:
Format = Bits 28:12 of graphics memory address (bits 31:29 MBZ)."
which translates to that the address of the HWS must be below 256MiB,
which is conveniently the mappable aperture.
This also appears to be true (but not documented as so) for gen4 and
gen5. To generalise we force it into the low mappable region for all
non-LLC platforms. If we locate the HWS at the top of the GTT the
machine will hard hang during boot (fails on pnv, gm45, ilk and byt,
but works on snb, ivb, hsw).
v2: Add comments to explain why use PIN_MAPPABLE even though we have
no intention of mapping the object. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With RC6 enabled, BYT has an HW issue in determining the right
Gfx busyness.
WA for Turbo + RC6: Use SW based Gfx busy-ness detection to decide
on increasing/decreasing the freq. This logic will monitor C0
counters of render/media power-wells over EI period and takes
necessary action based on these values
v2: Refactor duplicate code. (Ville)
v3: Reformat the comments. (Ville)
v4: Enable required counters and remove unwanted code (Ville)
v5: Added frequency change acceleration support and remove kernel-doc
style comments. (Ville)
v6: Updated comment section and Fix w/a comment. (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For whatever reason, MI_DISPLAY_FLIP fails to change tiling mode on
Baytrail, so just use CPU driven mmio flips instead.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76176
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently see random GPU hangs when using RCS flips with multiple
pipes on Ivybridge. Now that we have mmio flips, we can fairly cheaply
fallback to using CPU driven flips instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77104
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we isolate the legacy ringbuffer submission mechanism, which becomes
a good candidate to be abstracted away. This is prep-work for Execlists (which
will its own workload submission mechanism).
No functional changes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again, it's low-level enough to simply take a ringbuf and nothing
else.
Trivial change.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's simple enough that it doesn't need to know anything about the
engine.
Trivial change.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More prep work: with Execlists, we are going to start creating a lot
of extra ringbuffers soon, so these functions are handy.
No functional changes.
v2: rename allocate/destroy_ring_buffer to alloc/destroy_ringbuffer_obj
because the name is more meaningful and to mirror a similar function in
the context world: i915_gem_alloc_context_obj(). Change suggested by Brad
Volkin.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit of background on the context elements.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is an Execlists preparatory patch, since they make context ID become an
overloaded term:
- In the software, it was used to distinguish which context userspace was
trying to use.
- In the BSpec, the term is used to describe the 20-bits long field the
hardware uses to it to discriminate the contexts that are submitted to
the ELSP and inform the driver about their current status (via Context
Switch Interrupts and Context Status Buffers).
Initially, I tried to make the different meanings converge, but it proved
impossible:
- The software ctx->id is per-filp, while the hardware one needs to be
globally unique.
- Also, we multiplex several backing states objects per intel_context,
and all of them need unique HW IDs.
- I tried adding a per-filp ID and then composing the HW context ID as:
ctx->id + file_priv->id + ring->id, but the fact that the hardware only
uses 20-bits means we have to artificially limit the number of filps or
contexts the userspace can create.
The ctx->user_handle renaming bits are done with this Cocci patch (plus
manual frobbing of the struct declaration):
@@
struct intel_context c;
@@
- (c).id
+ c.user_handle
@@
struct intel_context *c;
@@
- (c)->id
+ c->user_handle
Also, while we are at it, s/DEFAULT_CONTEXT_ID/DEFAULT_CONTEXT_HANDLE and
change the type to unsigned 32 bits.
v2: s/handle/user_handle and change the type to uint32_t as suggested by
Chris Wilson.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have already advanced that Logical Ring Contexts have their own kind
of backing objects, but everything will be better explained in the Execlists
series. For now, suffice it to say that the current backing object is only
ever used with the render ring, so we're making this fact more explicit
(which is a good reason on its own).
As for the is_initialized flag, we only use to signify that the render state
has been initialized (a.k.a. golden context, a.k.a. null context). It doesn't
mean anything for the other engines, so make that distinction obvious.
Done with the following Coccinelle patch (plus manual frobbing of the struct):
@@
struct intel_context c;
@@
- (c).obj
+ c.legacy_hw_ctx.rcs_state
@@
struct intel_context *c;
@@
- (c)->obj
+ c->legacy_hw_ctx.rcs_state
@@
struct intel_context c;
@@
- (c).is_initialized
+ c.legacy_hw_ctx.initialized
@@
struct intel_context *c;
@@
- (c)->is_initialized
+ c->legacy_hw_ctx.initialized
This Execlists prep-work patch has been suggested by Chris Wilson and Daniel
Vetter separately.
Initially, it was two separate patches:
drm/i915: Rename ctx->obj to ctx->rcs_state
drm/i915: Make it obvious that ctx->id is merely a user handle
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/id/is_initialized/ to fix the subject and resolve a
conflict in i915_gem_context_reset. Also introduce a new lctx local
variable to avoid overtly long lines.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is preparatory work for Execlists: we plan to use it later to
allocate our own context objects (since Logical Ring Contexts do
not have the same kind of backing objects).
No functional changes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To achieve further power savings during system freeze (aka connected
standby, or s0ix) we have to send a PCI_D1 opregion notification. As
the information about the state we're entering (system freeze,
suspend to ram or suspend to disk) is only available through the ACPI
subsystem, make this support depend on the relevant kconfig option.
Things will still work if this option isn't set, albeit with less than
optimial power saving.
This also fixes a compile breakage when the option is not set introduced
in
commit e5747e3adc
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 12 08:35:47 2014 -0700
drm/i915: send proper opregion notifications on suspend/resume
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the assumption that media workloads are not as latency sensitive
for __wait_seqno, and that upclocking the GPU does not affect the BLT
engine. Under that assumption, we only wait to forcibly upclock the GPU
when we are stalling for results from the render pipeline.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The display in fdo#76483 pulses the hotplug line for link retraining
after we cut power to the main link on the source, even while it's
in D3.
fdo#76483
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Under some complicated circumstances (boot, suspend, resume, attach
second display, suspend, resume, suspend, detach second display,
resume, suspend, attach second display, resume), the fb_set_suspend()
call can somehow result in a modeset being attempted before we're
ready for it and things blow up in fun ways.
Running display init first fixes the issue.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's Apple machines out there which (probably completely arbitrarily)
restrict each output path to a particular head. This causes us to not
be able to locate the output data needed to power on/off the DP output
correctly.
We fix this by passing in a head index we know is valid (as opposed to
"head 0").
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When gcc 4.8 inlines this function, it eats up 16 bytes on the stack
every time. Eventually we hit warnings because our stack grew too
much:
ramnve0.c:1383:1: error: the frame size of 1496 bytes is larger than
1024 bytes
We fix this by preventing inlining for this function.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Universal planes are ready to leave 'experimental' state so drop the
kernel command line parameter that we've been hiding them behind.
Userspace clients that wish to receive universal planes will still need
to opt-in by setting the appropriate capability bit, so this should have
no impact on existing userspace.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the initial import of the helper for displayport multistream.
It consists of a topology manager, init/destroy/set mst state
It supports DP 1.2 MST sideband msg protocol handler - via hpd irqs
connector detect and edid retrieval interface.
It supports i2c device over DP 1.2 sideband msg protocol (EDID reads only)
bandwidth manager API via vcpi allocation and payload updating,
along with a helper to check the ACT status.
Objects:
MST topology manager - one per toplevel MST capable GPU port - not sure if this should be higher level again
MST branch unit - one instance per plugged branching unit - one at top of hierarchy - others hanging from ports
MST port - one port per port reported by branching units, can have MST units hanging from them as well.
Changes since initial posting:
a) add a mutex responsbile for the queues, it locks the sideband and msg slots, and msgs to transmit state
b) add worker to handle connection state change events, for MST device chaining and hotplug
c) add a payload spinlock
d) add path sideband msg support
e) fixup enum path resources transmit
f) reduce max dpcd msg to 16, as per DP1.2 spec.
g) separate tx queue kicking from irq processing and move irq acking back to drivers.
Changes since v0.2:
a) reorganise code,
b) drop ACT forcing code
c) add connector naming interface using path property
d) add topology dumper helper
e) proper reference counting and lookup for ports and mstbs.
f) move tx kicking into a workq
g) add aux locking - this should be redone
h) split teardown into two parts
i) start working on documentation on interface.
Changes since v0.3:
a) vc payload locking and tracking fixes
b) add hotplug callback into driver - replaces crazy return 1 scheme
c) txmsg + mst branch device refcount fixes
d) don't bail on mst shutdown if device is gone
e) change irq handler to take all 4 bytes of SINK_COUNT + ESI vectors
f) make DP payload updates timeout longer - observed on docking station redock
g) add more info to debugfs dumper
Changes since v0.4:
a) suspend/resume support
b) more debugging in debugfs
Changes since v0.5:
a) use byte * to avoid unnecessary stack usage
b) fix num_sdp_streams interpretation.
c) init payload state for unplug events
d) remove lenovo dock sink count hack
e) drop aux lock - post rebase
f) call hotplug on port destroy
TODO:
misc features
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This property will be used by the MST code to provide userspace
with a path to parse so it can recognise connectors around hotplugs.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required to get fbcon probing to work on new connectors,
callers should acquire the mode config lock before calling these.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This can be called to update things after dynamic connectors/encoders
are created/deleted.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a very crude page_flip implementation for UDL. There are ways
to make it better (make it asynchronous, make it do actual vsynced
flips...) but that's for another patch.
[airlied: fixup primary change]
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to be able to send page flip completion events.
Also while I'm at it, fix the error paths on init.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A race condition currently exists on Tegra, where it can happen that a
monitor attached via HDMI isn't detected during the initial FB helper
setup, but the hotplug event happens too early to be processed by the
poll helpers because they haven't been initialized yet. This happens
because on some boards the HDMI driver can control the regulator that
supplies the +5V pin on the HDMI connector. Therefore depending on the
timing between the initialization of the HDMI driver and the rest of
DRM, it's possible that the monitor returns the hotplug signal right
within the window where we would miss it.
Unfortunately, drm_kms_helper_poll_init() will wreak havoc when called
before at least some parts of the FB helpers have been set up.
This commit fixes this by splitting out the minimum of initialization
required to make drm_kms_helper_poll_init() work into a separate
function that can be called early. It is then safe to move all of the
poll helper initialization to an earlier point in time (before the
HDMI output driver has a chance to enable the +5V supply). That way if
the hotplug signal is returned before the initial FB helper setup, the
monitor will be forcefully detected at that point, and if the hotplug
signal is returned after that it will be properly handled by the poll
helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some drivers need to be able to have a perfect race-free fbcon setup.
Current drivers only enable hotplug processing after the call to
drm_fb_helper_initial_config which leaves a tiny but important race.
This race is especially noticable on embedded platforms where the
driver itself enables the voltage for the hdmi output, since only then
will monitors (after a bit of delay, as usual) respond by asserting
the hpd pin.
Most of the infrastructure is already there with the split-out
drm_fb_helper_init. And drm_fb_helper_initial_config already has all
the required locking to handle concurrent hpd events since
commit 53f1904bce
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 20 14:26:35 2014 +0100
drm/fb-helper: improve drm_fb_helper_initial_config locking
The only missing bit is making drm_fb_helper_hotplug_event save
against concurrent calls of drm_fb_helper_initial_config. The only
unprotected bit is the check for fb_helper->fb.
With that drivers can first initialize the fb helper, then enabel
hotplug processing and then set up the initial config all in a
completely race-free manner. Update kerneldoc and convert i915 as a
proof of concept.
Feature requested by Thierry since his tegra driver atm reliably boots
slowly enough to misses the hotplug event for an external hdmi screen,
but also reliably boots to quickly for the hpd pin to be asserted when
the fb helper calls into the hdmi ->detect function.
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a sparse warning: ttm_bo_reserve()'s last argument is a
pointer to a struct, so use NULL as nullpointer.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use module_init instead of late_initcall, as is the norm for modular
drivers.
module_init was used until 6e8de0bd6a
("drm/tilcdc: add encoder slave (v2)") changed it to a late_initcall,
but it does not explain why. Tests show it's working properly with
module_init.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TI tilcdc driver is designed with a notion of submodules. Currently,
at unload time, these submodules are iterated and destroyed.
Now that the tilcdc remove order is fixed, this can be handled perfectly
by the kernel using the device infrastructure, since each submodule
is a kernel driver itself, and they are only destroy()'ed at unload
time. Therefore we move the destroy() functionality to each submodule's
remove().
Also, remove some checks in the unloading process since the new code
guarantees the resources are allocated and need a release.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
display_timings_release calls kfree on the display_timings object passed
to it. Calling kfree after it is wrong. SLUB debug showed the following
warning:
=============================================================================
BUG kmalloc-64 (Tainted: G W ): Object already free
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in of_get_display_timings+0x2c/0x214 age=601 cpu=0
pid=884
__slab_alloc.constprop.79+0x2e0/0x33c
kmem_cache_alloc+0xac/0xdc
of_get_display_timings+0x2c/0x214
panel_probe+0x7c/0x314 [tilcdc]
platform_drv_probe+0x18/0x48
[..snip..]
INFO: Freed in panel_destroy+0x18/0x3c [tilcdc] age=0 cpu=0 pid=907
__slab_free+0x34/0x330
panel_destroy+0x18/0x3c [tilcdc]
tilcdc_unload+0xd0/0x118 [tilcdc]
drm_dev_unregister+0x24/0x98
[..snip..]
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unregister resources in the correct order on tilcdc_drm_fini, which is
the reverse order they were registered during tilcdc_drm_init.
This also means unregistering the driver before releasing its resources.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver did not unregister the allocated framebuffer, which caused
memory leaks (and memory manager WARNs) when unloading. Also, the
framebuffer device under /dev still existed after unloading.
Add a call to drm_fbdev_cma_fini when unloading the module to prevent
both issues.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a drm_sysfs_connector_remove call when we destroy the panel to make
sure the connector node in sysfs gets deleted.
This is required for proper unload and re-load of this driver, otherwise
we will get a warning about a duplicate filename in sysfs.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a drm_sysfs_connector_remove call when we destroy the panel to make
sure the connector node in sysfs gets deleted.
This is required for proper unload and re-load of this driver as a
module. Without this, we would get a warning at re-load time like so:
tda998x 0-0070: found TDA19988
------------[ cut here ]------------
WARNING: CPU: 0 PID: 825 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x54/0x74()
sysfs: cannot create duplicate filename '/class/drm/card0-HDMI-A-1'
Modules linked in: [..]
CPU: 0 PID: 825 Comm: modprobe Not tainted 3.15.0-rc4-00027-g9dcdef4 #82
[<c0013bb8>] (unwind_backtrace) from [<c0011824>] (show_stack+0x10/0x14)
[<c0011824>] (show_stack) from [<c0034e8c>] (warn_slowpath_common+0x68/0x88)
[<c0034e8c>] (warn_slowpath_common) from [<c0034edc>] (warn_slowpath_fmt+0x30/0x40)
[<c0034edc>] (warn_slowpath_fmt) from [<c01243f4>] (sysfs_warn_dup+0x54/0x74)
[<c01243f4>] (sysfs_warn_dup) from [<c0124708>] (sysfs_do_create_link_sd.isra.2+0xb0/0xb8)
[<c0124708>] (sysfs_do_create_link_sd.isra.2) from [<c02ae37c>] (device_add+0x338/0x520)
[<c02ae37c>] (device_add) from [<c02ae6e8>] (device_create_groups_vargs+0xa0/0xc4)
[<c02ae6e8>] (device_create_groups_vargs) from [<c02ae758>] (device_create+0x24/0x2c)
[<c02ae758>] (device_create) from [<c029b4ec>] (drm_sysfs_connector_add+0x64/0x204)
[<c029b4ec>] (drm_sysfs_connector_add) from [<bf0b1b40>] (slave_modeset_init+0x120/0x1bc [tilcdc])
[<bf0b1b40>] (slave_modeset_init [tilcdc]) from [<bf0b2be8>] (tilcdc_load+0x214/0x4c0 [tilcdc])
[<bf0b2be8>] (tilcdc_load [tilcdc]) from [<c029955c>] (drm_dev_register+0xa4/0x104)
[..snip..]
---[ end trace 4df8d614936ebdee ]---
[drm:drm_sysfs_connector_add] *ERROR* failed to register connector device: -17
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a drm_sysfs_connector_remove call when we destroy the panel to make
sure the connector node in sysfs gets deleted.
This is required for proper unload and re-load of this driver as a
module. Without this, we would get a warning at re-load time like so:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 824 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x54/0x74()
sysfs: cannot create duplicate filename '/class/drm/card0-LVDS-1'
Modules linked in: [...]
CPU: 0 PID: 824 Comm: modprobe Not tainted 3.15.0-rc4-00027-g6484f96-dirty #81
[<c0013bb8>] (unwind_backtrace) from [<c0011824>] (show_stack+0x10/0x14)
[<c0011824>] (show_stack) from [<c0034e8c>] (warn_slowpath_common+0x68/0x88)
[<c0034e8c>] (warn_slowpath_common) from [<c0034edc>] (warn_slowpath_fmt+0x30/0x40)
[<c0034edc>] (warn_slowpath_fmt) from [<c01243f4>] (sysfs_warn_dup+0x54/0x74)
[<c01243f4>] (sysfs_warn_dup) from [<c0124708>] (sysfs_do_create_link_sd.isra.2+0xb0/0xb8)
[<c0124708>] (sysfs_do_create_link_sd.isra.2) from [<c02ae37c>] (device_add+0x338/0x520)
[<c02ae37c>] (device_add) from [<c02ae6e8>] (device_create_groups_vargs+0xa0/0xc4)
[<c02ae6e8>] (device_create_groups_vargs) from [<c02ae758>] (device_create+0x24/0x2c)
[<c02ae758>] (device_create) from [<c029b4ec>] (drm_sysfs_connector_add+0x64/0x204)
[<c029b4ec>] (drm_sysfs_connector_add) from [<bf0b1fec>] (panel_modeset_init+0xb8/0x134 [tilcdc])
[<bf0b1fec>] (panel_modeset_init [tilcdc]) from [<bf0b2bf0>] (tilcdc_load+0x214/0x4c0 [tilcdc])
[<bf0b2bf0>] (tilcdc_load [tilcdc]) from [<c029955c>] (drm_dev_register+0xa4/0x104)
[ .. snip .. ]
---[ end trace b2d09cd9578b0497 ]---
[drm:drm_sysfs_connector_add] *ERROR* failed to register connector device: -17
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "flags" parameter of the DRM_IOCTL_MODE_ADDFB2 ioctl must be
propagated and used by the driver.
The only possible value of flags is DRM_MODE_FB_INTERLACED.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Benjamin GAIGNARD <benjamin.gaignard@st.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
bo->mem.placement is not initialized when ttm_bo_man_get_node is called,
so the flag had no effect at all.
v2: change nouveau and vmwgfx as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-next' of git://people.freedesktop.org/~dvdhrm/linux:
drm/omap: remove null test before kfree
drm/bochs: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN
drm/ttm: recognize ARM arch in ioprot handler
drm: enable render-nodes by default
drm/ttm: remove declaration of ttm_tt_cache_flush
drm/gem: remove misleading gfp parameter to get_pages()
drm/omap: use __GFP_DMA32 for shmem-backed gem
drm/i915: use shmem helpers if possible
Conflicts:
drivers/gpu/drm/drm_stub.c
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: David Airlie <airlied@linux.ie>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Nouveau can now be used on ARM, so add an ioprot handler for this
architecture.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
We introduced render-nodes about 1/2 year ago and no problems showed up.
Remove the drm_rnodes argument and enable them by default now.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
drm_gem_get_pages() currently allows passing a 'gfp' parameter that is
passed to shmem combined with mapping_gfp_mask(). Given that the default
mapping_gfp_mask() is GFP_HIGHUSER, it is _very_ unlikely that anyone will
ever make use of that parameter. In fact, all drivers currently pass
redundant flags or 0.
This patch removes the 'gfp' parameter. The only reason to keep it is to
remove flags like __GFP_WAIT. But in its current form, it can only be used
to add flags. So to remove __GFP_WAIT, you'd have to drop it from the
mapping_gfp_mask, which again is stupid as this mask is used by shmem-core
for other allocations, too.
If any driver ever requires that parameter, we can introduce a new helper
that takes the raw 'gfp' parameter. The caller'd be responsible to combine
it with mapping_gfp_mask() in a suitable way. The current
drm_gem_get_pages() helper would then simply use mapping_gfp_mask() and
call the new helper. This is what shmem_read_mapping_pages{_gfp,} does
right now.
Moreover, the gfp-zone flag-usage is not obvious: If you pass a modified
zone, shmem core will WARN() or even BUG(). In other words, the following
must be true for 'gfp' passed to shmem_read_mapping_pages_gfp():
gfp_zone(mapping_gfp_mask(mapping)) == gfp_zone(gfp)
Add a comment to drm_gem_read_pages() explaining that constraint.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
OMAP requires bo-pages to be in the DMA32 zone. Explicitly request this by
setting __GFP_DMA32 as mapping-gfp-mask during shmem initialization. This
drops HIGHMEM from the gfp-mask and uses DMA32 instead. shmem-core takes
care to relocate pages during swap-in in case they have been loaded into
the wrong zone.
It is _not_ possible to pass __GFP_DMA32 to shmem_read_mapping_page_gfp()
as the page might have already been swapped-in at that time. The zone-mask
must be set during initialization and be kept constant for now.
Remove the now superfluous TODO in omap_gem.c.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
With the new checks in place, we can see we're doing things backwards,
so fix them up per the spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some Thinkpad laptops' firmware will initiate a backlight level change
request through operation region on the events of AC plug/unplug, but
since we are not using firmware's interface to do the backlight setting
on these affected laptops, we do not want the firmware to use some
arbitrary value from its ASL variable to set the backlight level on
AC plug/unplug either.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=76491
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77091
Reported-and-tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Reported-and-tested-by: Anton Gubarkov <anton.gubarkov@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As Ville points out, it's possible/probable we don't actually need this.
Potentially, this validates the letter of the spec, and not the spirit.
Ville:
> I discussed this on irc w/ Ben, and I was suggesting we don't need to
> poll. Polling apparently can be used as a workaround for certain
> hardware issues, but it looks like those issues shouldn't affect us,
> for the momemnt at least. So my suggestion was to try w/o polling
> first (since there could be some power cost to polling) and add the
> poll bit if problems arise.
Rodrigo: Spec suggests this as an W/A for GT3. However semaphores didn't
worked in my BDW GT2 on Signal Mode. So pool mode is definitely needed.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simple debugfs file to display the current state of semaphores. This is
useful if you want to see the state without hanging the GPU.
NOTE: This patch is optional to the series.
NOTE2: Like the GPU error state collection, the reads are currently
incoherent.
v2 (Rodrigo): * Iterate only on active rings.
* s/ring_buffer/engine_cs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the semaphore information is in an object, just dump it, and let
the user parse it later.
NOTE: The page being used for the semaphores are incoherent with the
CPU. No matter what I do, I cannot figure out a way to read anything but
0s. Note that the semaphore waits are indeed working.
v2: Don't print signal, and wait (they should be the same). Instead,
print sync_seqno (Chris)
v3: Free the semaphore error object (Chris)
v4: Fix semaphore offset calculation during error state collection
(Ville)
v5: VCS2 rebase
Make semaphore object error capture coding style consistent (Ville)
Do the proper math for the signal offset (Ville)
v6: Fix small conflicts on rebase and s/ring_buffer/engine_cs (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ipehr just carries Dword 0 and on Gen 8, offsets are located
on Dword 2 and 3 of MI_SEMAPHORE_WAIT.
This implementation was based on Ben's work and on Ville's suggestion for Ben
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Fixup format string.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore waits use a new instruction, MI_SEMAPHORE_WAIT. The seqno to
wait on is all well defined by the table in the previous patch. There is
nothing else different from previous GEN's semaphore synchronization
code.
v2: Update macros to not require the other ring's ring->id (Chris)
v3: Add missing VCS2 gen8_ring_wait init besides
s/ring_buffer/engine_cs (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore signalling works similarly to previous GENs with the exception
that the per ring mailboxes no longer exist. Instead you must define
your own space, somewhere in the GTT.
The comments in the code define the layout I've opted for, which should
be fairly future proof. Ie. I tried to define offsets in abstract terms
(NUM_RINGS, seqno size, etc).
NOTE: If one wanted to move this to the HWSP they could. I've decided
one 4k object would be easier to deal with, and provide potential wins
with cache locality, but that's all speculative.
v2: Update the macro to not need the other ring's ring->id (Chris)
Update the comment to use the correct formula (Chris)
v3: Move the macros the ringbuffer.h to prevent churn in next patch
(Ville)
v4: Fixed compilation rebase conflict
commit 1ec9e26dda
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Feb 14 14:01:11 2014 +0100
drm/i915: Consolidate binding parameters into flags
v5: VCS2 rebase
Replace hweight_long with hweight32
v6 (Rodrigo): * Add missed VC2 gen8 ring signal init
* fixing conflicst on rebase
* minor fixes on address table
* remove WARN_ON
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the ring mask we now have an easy way to know the number of rings
in the system, and therefore can accurately predict the number of dwords
to emit for semaphore signalling. This was not possible (easily)
previously.
There should be no functional impact, simply fewer instructions emitted.
While we're here, simply do the round up to 2 instead of the fancier
rounding we did before, which rounding up per mbox, ie 4. This also
allows us to drop the unnecessary MI_NOOP, so not really 4, 3.
v2: Use 3 dwords instead of 4 (Ville)
Do the proper calculation to get the number of dwords to emit (Ville)
Conditionally set .sync_to when semaphores are enabled (Ville)
v3: Rebased on VCS2
Replace hweight_long with hweight32 (Ville)
v4: Pull out the accidentally squashed hunk from the next patch after
rebase (Daniel).
v5: Fix conflict after rebase (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen8 has already had some differentiation with how it handles rings.
Semaphores bring yet more differences, and now is as good a time as any
to do the split.
Also, since gen8 doesn't actually use semaphores up until this point,
put the proper "NULL" values in for the mbox info.
v2: v1 had a stale commit message
v3: Move everything in the is_semaphore_enabled() check
v4: VCS2 rebase
Remove double assignment of signal in render ring (Ville)
v5: Adding missed VCS2 signal init on gen8+ (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ring index calculation table was out of date after other rings were added,
although the formula is flexible and scale when adding new rings.
So this patch just update the comments and add a brief explanation
why to use sync_seqno[ring index].
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It just fix a typo.
v2: removing underscore to let this like all other ring names (Oscar)
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by (v1): Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 'i915_driver_preclose()' function has a parameter called 'file_priv'.
However, this is misleading as the structure it points to is a 'drm_file' not a
'drm_i915_file_private'. It should be named just 'file' to avoid confusion.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The always-on power well pixel path on haswell is routed such that it
bypasses the panel fitter when we use is. Which means the pfit CRC
source won't work in that configuration.
Add a new disallow-bypass flags to the pfit pipe config state and set
it when we want to use the pf CRC. Results in a bit of flicker, but
should get the job done. We'll also undo do it afterwards to make sure
other tests arent' negatively affected.
Totally untested due to lack of hsw laptops around here.
v2: s/disallow_bypass/force_power_well_on/ to avoid a double negative
(Damien).
v3: force_thru because roadsigns.
v4: Don't forget the power wells! Also note that until the runtime pm
for DPMS series is fully merged the simple disable/enable trick won't
work since the ->crtc_mode_set callback is still required to do nasty
things. This stuff is tricky, but I think by both fixing up
get_crtc_power_domains and the debugfs wa code we should always
grab/drop the additional power well correctly.
v5: Wrap in () as suggested by Damien to avoid setting reserved values
for the edp transcoder path on bdw+
References: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The workaround to limit SDE poly depth FIFO to 2 is not applied because
3D Chicken-3 mask bit is not set.
WaLimitSizeOfSDEPolyFifo is only for BDW-A and could be removed.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the root cause is understood now and with the fix
commit 564ed191f5
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Jun 13 14:54:21 2014 +0300
drm/i915: gmch: fix stuck primary plane due to memory self-refresh mode
in place the magic for G4x chipsets introduced with commit
commit 61bc95c1fb
Author: Egbert Eich <eich@suse.com>
Date: Mon Mar 4 09:24:38 2013 -0500
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
to avoided occasional screen blanking on mode changes can finally
be removed.
It's been verified that Imre's fix also resolves the said issue.
Signed-off-by: Egbert Eich <eich@suse.de>
Tested-by: Stefan Dirsch <sndirsch@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As pointed out before we don't have a reliable way to read back ips
status on BDW without the risk to disable it when reading.
However now we are pretending that IPS on BDW is always on and getting
people confused about it.
So this patch allows people to know if ips was ever attempted to be enabled.
Even if the current status is impossible to be ascertain.
v2: (spotted by Paulo):
* A version that at least compiles
* with more clear messages
* let Cheryview on the safe side until we aren't sure that checking ips
state on ips won't disable it.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're forgetting to unpin the last_context from the ggtt at GPU reset
time. This leads to the vma pin_count leaking at every reset if the
last context wasn't the ring default context. Further use of the same
context will trigger the pin_count check in i915_gem_object_pin() and
userspace will be faced with EBUSY as a result.
This plaques kms_flip rather badly since it performs lots of resets,
and every fd has its own default context these days.
Fix the problem by properly unpinning the last context at reset.
This regression seems to back to
commit acce9ffa48
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri Dec 6 14:11:03 2013 -0800
drm/i915: Better reset handling for contexts
Testcase: igt/gem_ctx_exec/reset-pin-leak
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The digital ports from Ironlake and up have the ability to distinguish
between long and short HPD pulses. Displayport 1.1 only uses the short
form to request link retraining usually, so we haven't really needed
support for it until now.
However with DP 1.2 MST we need to handle the short irqs on their
own outside the modesetting locking the long hpd's involve. This
patch adds the framework to distinguish between short/long to the
current code base, to lay the basis for future DP 1.2 MST work.
This should mean we get better bisectability in case of regression
due to the new irq handling.
v2: add GM45 support (untested, due to lack of hw)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
[danvet: Fix conflicts in i915_irq.c with Oscar Mateo's irq handling
race fixes and a trivial one in intel_drv.h with the psr code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Blanking/unblanking the console in a loop on an Asus T100 sometimes
leaves the console blank. After some digging I found that applying
commit 61bc95c1fb
Author: Egbert Eich <eich@suse.com>
Date: Mon Mar 4 09:24:38 2013 -0500
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
fixed VLV too.
In my case the problem seemed to happen already during the previous crtc
disabling and went away if I disabled self-refresh mode before disabling
the primary plane.
The root cause for this is that updates from the shadow to live plane
control register are blocked at vblank time if the memory self-refresh
mode (aka max-fifo mode on VLV) is active at that moment. The controller
checks at frame start time if the CPU is in C0 and the self-refresh mode
enable bit is set and if so activates self-reresh mode, otherwise
deactivates it. So to make sure that the plane truly gets disabled before
pipe-off we have to:
1. disable memory self-refresh mode
2. disable plane
3. wait for vblank
4. disable pipe
5. wait for pipe-off
v2:
- add explanation for the root cause from HW team (Cesar Mancini et al)
- remove note about the CPU C7S state, in my latest tests disabling it
alone didn't make a difference
- add vblank between disabling plane and pipe (Ville)
- apply the same workaround for all gmch platforms (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm it's possible that we enable the memory self-refresh mode before the
watermark levels used by this mode are programmed with valid values. So
move the enabling after we programmed the WM levels.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This functionality will be also needed by an upcoming patch, so factor
it out. As a bonus this also makes things a bit more uniform across
platforms. Note that this also changes the register read-modify-write
to a simple write during disabling. This is what we do during enabling
anyway and according to the spec all the relevant bits are reserved-MBZ
or reserved with a 0 default value.
v2:
- unchanged
v3:
- fix missing cxsr disabling on pineview (Deepak)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the CMNRESET deassert is part of the cmnlane power well,
intel_reset_dpio() is called too late to make any difference. We've
deasserted CMNRESET by that time, and so the off+on toggle w/a will
never kick in.
Move the workaround to intel_power_domains_init_hw() where it gets
called before we enable the init power domain.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the clutter in __vlv_set_power_well() by moving the cmnlane
handling into custom enable/disable hooks for the cmnlane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a slightly different way of readoing out the cdclk in
gmbus_set_freq(). Kill that and just call .get_display_clock_speed().
Also need to remove the GMBUSFREQ update from intel_i2c_reset() since
that gets called way too early. Let's do it in intel_modeset_init_hw()
instead, and also pull the initial vlv_cdclk_freq update there from
init_clock gating.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If someone is interested in the current cdclk frquency it should
be stable and not in process of changing frquency. Warn if the current
and requested cdclk don't match in .get_display_clock_spee() on vlv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV Punit doesn't support the 400MHz cdclk option, so we bypass the
Punit and poke at CCK directly. However we forgot to wait for the
frequeency change to complete. Poll the CCK clock status to make sure
the clock has changed before we fire up any pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the cdclk frequency to 200MHz on vlv when all pipes are off. In
theory we should be able to use 200MHz also when the pixel clock is at
most 90% of 200MHz. However in practice all we seem to get is a solid
color picture or an otherwise corrupted display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the HPLL frequency one of the supported cdclk frquencies is
either 320MHz or 333MHz. Figure out which one it is to accurately pick
the minimal required cdclk. This would also avoid a warning from the
cdclk code where it compares the actual cdclk read out from the hardware
with a value that was calculated using valleyview_calc_cdclk().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a standard hook for reading out the current cdclk. Move the VLV
code from valleyview_cur_cdclk() to .get_display_clock_speed().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid using magic values for CCK frequency bits. Also the mask we were
using for the requested frequency was one bit too short. Fix it up.
Note: This also fixes the #define for a mask (spotted by Jesse in his
review).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add note about mask change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use kHz units in vlv cdclk code since that's more customary.
Also replace the precomputed 90% values with *9/10 computation
for extra clarity.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTuaWZAAoJEHm+PkMAQRiGfkIH/2Hhwrg51GWazUYIXVxz5zLU
kPMlaws3vankbhka9HCg02eS3tkzr6shO3F/qlBba+5GUkUDKCcCisIsvk4hgZZg
7YqepTvcaupNxIp4TmTGm1FYVK1GpaWFdJVgg2PDdGFahw3HSlfZoTkBzirNCwga
p/jfeRzathbUixpz9OAC1AEn2gP1AxNRpSt1wShL5rexBb1YRXCPuCEt9B0UsVoR
mzKf5xEsuaZnpCuvWK4S60fjfVhTe8UJ/xGPPfdLyIXU0rvhaKzfeVQO6F5nIQBy
Xvrar1f7oOPZaJRdlmPvAimS7iS8lq/YctuHu7ia1NdJSihtA5sRPf7cWAw2d7s=
=4PrL
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc4' into drm-intel-next-queued
Due to Dave's vacation drm-next hasn't opened yet for 3.17 so I
couldn't move my drm-intel-next queue forward yet like I usually do.
Just pull in the latest upstream -rc to unblock patch merging - I
don't want to needlessly rebase my current patch pile really and void
all the testing we've done already.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.
* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
Update MSM's DRM driver to use the component match support rather than
add_components.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zvT1
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
Inlcude the pipe-size and cursor-size in debugfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Contrary to the host-backed shader interface that has a per-context
name-space for shaders, the compat shader namespace was per client
(or rather, per file). Fix this so that the compat shader namespace is per
context, and at the same time, make command buffer managed context resource
management generic.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the variant pointer into the armada_crtc structure, and update for
the resulting changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the variant initialisation entirely to the CRTC init function -
the variant support is really about the CRTC properties than the whole
system, and we want to treat each CRTC individually when we support DT.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the number of CRTCs registered to size the vblank arrays rather than
our own count. Number CRTCs using this as well. This permits us to
register CRTCs as components in the near future rather than as part of a
single device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: stable@vger.kernel.org
Cc: Christopher Friedt <chrisfriedt@gmail.com>
Tested-by: Christopher Friedt <chrisfriedt@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
The GEN FBC unit provides the ability to set a low pass on frames it
attempts to compress. If a frame is less than a certain amount
compressibility (2:1, 4:1) it will not bother. This allows the driver to
reduce the size it requests out of stolen memory.
Unluckily, a few months ago, Ville actually began using this feature for
framebuffers that are 16bpp (not sure why not 8bpp). In those cases, we
are already using this mechanism for a different purpose, and so we can
only achieve one further level of compression (2:1 -> 4:1)
FBC GEN1, ie. pre-G45 is ignored.
The cleverness of the patch is Art's. The bugs are mine.
v2: Update message and including missing threshold case 3 (Spotted by Arthur).
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Right now, there is no threshold (0 means fail, 1 means 1:1 compression
limit). This is to split the function/non-functional change of the next
patch.
The next patch will start to attempt to reduce the amount of CFB space
we need for dire situations. It will be contained within this function.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We are already using the size to determine whether or not to free the
object, so there is no functional change there. Almost everything else
has changed to static allocations of the drm_mm_node too.
Aside from bringing this inline with much of our other code, this makes
error paths slightly simpler, which benefits the look of an upcoming
patch.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
misc fixes, output fixes for 4k monitor, dpm lockup fixes
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: page table BOs are kernel allocations
drm/radeon/cik: fix typo in EOP packet
drm/radeon: Track the status of a page flip more explicitly
drm/radeon/dpm: fix vddci setup typo on cayman
drm/radeon/dpm: fix typo in vddci setup for eg/btc
drm/radeon: use RADEON_MAX_CRTCS, RADEON_MAX_AFMT_BLOCKS (v2)
drm/radeon: Use only one line for whole DPCD debug output
drm/radeon: add a module parameter to control deep color support
drm/radeon: enable bapm by default on desktop TN/RL boards
drm/radeon: enable bapm by default on KV/KB
drm/radeon: only apply bapm changes for AC power on ARUBA
drm/radeon: adjust default dispclk on DCE6 (v2)
Userspace shouldn't be able to access them.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Volatile bit was in the wrong location. This bit is
not used at the moment.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
use mm.h definition
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Higher RC6 residency is observed using timeout mode
instead of EI mode. This applies to Broadwell only.
The difference is particularly noticeable with video
playback.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This prevents a panic: radeon_crtc_handle_page_flip() could run before
radeon_flip_work_func(), triggering the BUG_ON() in drm_vblank_put().
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some monitors seem to have problems with deep color enabled, even
though they claim to support it. I'm not sure if the monitor
need a quirk or if the driver is doing something the monitor doesn't
like. At this point lets just disable deep color by default like
we did for hdmi audio and work through the bugs so we can eventually
enable it by default.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80531
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm enabled the GPU and CPU to share TDP headroom. It was
disabled by default since some laptops hung when it was enabled
in conjunction with dpm. It seems to be stable on desktop
boards and fixes hangs on boot with dpm enabled on certain
boards, so enable it by default on desktop boards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72921
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm allows the GPU and CPU to share TDP. This allows
for additional performance out of the GPU and CPU when
the headroom is available.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the default to 600Mhz if it's not set in the bios,
and bump the default to 600Mhz if it's lower than that.
This fixes display issues with certain 4k DP monitors when
using 5.4 Ghz DP clocks.
v2: fix typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is possible that, by the time we run i915_drm_freeze(),
delayed_resume_work was already queued but did not run yet. If it
still didn't run after intel_runtime_pm_disable_interrupts(), by the
time it runs it will try to change the interrupt registers with the
interrupts already disabled, which will trigger a WARN. We can
reliably reproduce this with the pm_rpm system-suspend test case.
In order to avoid the problem, we have to flush the work before
disabling the interrupts. We could also cancel the work instead of
flushing it, but that would require us to put a runtime PM reference -
and any other resource we may need in the future - in case the work
was already queued, so I believe flushing the work is more
future-proof, although less efficient. But I can also change this part
if someone requests.
Another thing I tried was to move the intel_suspend_gt_powersave()
call to before intel_runtime_pm_disable_interrupts(), but since that
function needs to be called after the interrupts are already disabled,
due to dev_priv->rps.work, this strategy didn't work.
Testcase: igt/pm_rpm/system-suspend
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80517
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Drop WA to fix Voltage not getting dropped to Vmin when Gfx is power
gated for latest VLV revision.
Workaround fixed in Latest VLV revision. Forcing Gfx clk up not needed,
and Requesting the min freq should bring bring the voltage Vnn.
v2: Drop WA for Latest VLV revision (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: modified code comment, reformatted the commit message a bit.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently we can't trust this field on other platforms and need to find
some other way.
This fixes a regression introduced in
commit 27da3bdfcf
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Apr 4 16:12:07 2014 -0700
drm/i915: use VBT to determine whether to enumerate the VGA port
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BDW signals the flip done interrupt immediately after the DSPSURF write
when the plane is disabled. This is true even if we've already armed
DSPCNTR to enable the plane at the next vblank. This causes major
problems for our page flip code which relies on the flip done interrupts
happening at vblank time.
So what happens is that we enable the plane, and immediately allow
userspace to submit a page flip. If the plane is still in the process
of being enabled when the page flip is issued, the flip done gets
signalled immediately. Our DSPSURFLIVE check catches this to prevent
premature flip completion, but it also means that we don't get a flip
done interrupt when the plane actually gets enabled, and so the page
flip is never completed.
Work around this by re-introducing blocking vblank waits on BDW
whenever we enable the primary plane.
I removed some of the vblank waits here:
commit 6304cd91e7
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Apr 25 13:30:12 2014 +0300
drm/i915: Drop the excessive vblank waits from modeset codepaths
To avoid these blocking vblank waits we should start using the vblank
interrupt instead of the flip done interrupt to complete page flips.
But that's material for another patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79354
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fixes for 3.16-rc2; regressions, races, and warns; Broadwell PCI IDs.
* tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
The TDA998x can't handle modes with clocks above 150MHz, or resolutions
larger than 8192x2048.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
One of Jean-Francois patches changed the EDID polling to once every
10ms for 10 interations, whereas the original code did 1ms for 100
interations. This appears to cause boot-time detection to take
noticably longer. Revert this change.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently tda998x_encoder_destroy() calls cec_write() and reg_clear(),
as part of the release procedure. Such calls need to access the I2C bus
and therefore, we need to call them before drm_i2c_encoder_destroy()
which unregisters the I2C device.
This commit moves the latter so it's done afterwards.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Ezequiel García <ezequiel@vanguardiasur.com.ar>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
crtc->primary->fb may be NULL upon entry to intel_pipe_set_base() if the
primary plane has previously been disabled via the universal plane
interface. We need to check for NULL before trying to reference
old_fb's obj.
This fixes a regression introduced in
commit a071fa0064
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 18 23:28:09 2014 +0200
drm/i915: Introduce accurate frontbuffer tracking
Testcase: igt/kms_universal_plane
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For MIPI, DSI PLL is configured separately in vlv_configure_dsi_pll
during the DSI enable sequence
Causing WARN dump otherwise in dpio_reads
v2: Add IS_CHERRYVIEW check as suggested by Ville
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This pull-request fixes hdmi power-off order issue, mixer issues
related to power on/off, and includes trivial fixups.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: enable vsync interrupt while waiting for vblank
drm/exynos: soft reset mixer before reconfigure after power-on
drm/exynos: allow multiple layer updates per vsync for mixer
drm/exynos: stop mixer before gating clocks during poweroff
drm/exynos: set power state variable after enabling clocks and power
drm/exynos: disable unused windows on apply
drm/exynos: Fix de-registration ordering
drm/exynos: change zero to NULL for sparse
drm/exynos: dpi: Fix NULL pointer dereference with legacy bindings
drm/exynos: hdmi: fix power order issue
A handful of fixes from various folks.
* 'msm-fixes-3.16' of git://people.freedesktop.org/~robclark/linux:
drm/msm: fix IOMMU cleanup for -EPROBE_DEFER
drm/msm: use PAGE_ALIGNED instead of IS_ALIGNED(PAGE_SIZE)
drm/msm/hdmi: set hdp clock rate before prepare_enable
drm/msm: storage class should be before const qualifier
drm/msm: Replace type of paddr to uint32_t.
If user uses wrong ioctl command with _IOC_NONE and argument size
greater than 0, it can cause NULL pointer access from memset of line
463. If _IOC_NONE, don't memset to 0 for kdata.
Signed-off-by: Zhaowei Yuan <zhaowei.yuan@samsung.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
mixer_wait_for_vblank function expects that the upcoming
vsync interrupt handler routine will clear the
wait_vsync_event atomic variable.
For this to happen, interrupts should be enabled and
disabled properly.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Mixer soft reset is a recommended step before reconfiguring
the mixer after power on. Mixer looses the previous state of
DMAs if soft reset. This is the recommendation from the
hardware team.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Allowing only one layer update per vsync can cause issues
while there are update available for both layers. There is
a good amount of possibility to loose updates if we allow
single update per vsync.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fallout from
commit 46470fc932
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Wed May 21 19:01:06 2014 +0300
drm/i915: Add null state batch to active list
undid the earlier fix of only marking the ctx as initialised after it is
saved by the hardware during a SET_CONTEXT operation:
commit ad1d219974
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Sat Dec 28 13:31:49 2013 -0800
drm/i915: set ctx->initialized only after RCS
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[Jani: add reference to the earlier fix in the commit messsage.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Mixer should be power gated only after it is gracefully stopped.
The recommended sequence is to Stop the mixer and wait till
it enters to IDLE state before gating the clocks and power to
the mixer.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Power state variable holds the state of the mixer device.
Power on and power off functions are toggling these variable
at wrong place.
State variable should be changed to true only after Runtime
PM and clocks are enabled. Else it may result to a situation
where mixer registers are accessed with device power enabled.
Similar logic for poweroff sequence.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch disables non-enabled HW windows on applying
configuration, it will allow to clear windows enabled
by bootloader.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'exynos_drm_pdev' was not getting unregistered if platform_driver_register()
failed. Fix the ordering to allow this. This also fixes the below warning by
moving the #endif macro. While at it also fix the ordering in the exit function
so that de-registration happens in opposite order of registration.
drivers/gpu/drm/exynos/exynos_drm_drv.c:768:1: warning: label
'err_unregister_pd' defined but not used [-Wunused-label]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We recently changed this function to return a pointer instead of an int
so we need to change this zero to a NULL or Sparse complains:
drivers/gpu/drm/exynos/exynos_drm_drv.h:346:47:
warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If there is no panel node in DT and instead display timings are provided
directly in FIMD node, there is no panel object created and ctx->panel
becomes NULL. However during Exynos DRM initialization
drm_helper_hpd_irq_event() is called, which in turns calls
exynos_dpi_detect(), which dereferences ctx->panel without a check,
causing a NULL pointer derefrence.
This patch fixes the issue by adding necessary NULL pointer check.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves page fault issue of Mixer when disabled.
The SFRs of VP and Mixer are updated by Vertical Sync of Timing
generator which is a part of HDMI so the sequence to disable TV
Subsystem should be as following:
VP -> Mixer -> HDMI
For this, this patch disables Mixer and VP (if used) prior to
disabling HDMI.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Apparently there are Apple laptops with magic smoke for a VBIOS, which
we fail to find and use. Default to having and setting up backlight in
this case.
This fixes a regression introduced by
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=77831
Reported-and-tested-by: Matteo Cypriani <mcy@lm7.fr>
Cc: stable@vger.kernel.org # 3.15+
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jesse noticed that the punit communication needed to query the VLV power
well status can cause substantial delays. Since we can query the state
frequently, for example during I2C transfers, maintain a cached version
of the HW state to get rid of this delay.
This fixes at least one reported regression where boot time increased by
~4 seconds due to frequent power well state queries on VLV during eDP
EDID read.
This regression has been introduced in
commit bb4932c4f1
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:33 2014 +0300
drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Reported-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If probe fails after IOMMU is attached, we need to detach in order to
clean up properly. Before this change, IOMMU faults would occur if the
probe failed (-EPROBE_DEFER).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
use mm.h definition
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The clock driver usually complains when a clock is being prepared
before setting its rate. It is the case here for "core_clk" which
needs to be set at 19.2 MHz before we attempt a prepare_enable().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch helps to avoid the following build issue:
drivers/gpu/drm/msm/msm_fbdev.c:108:2: error: passing argument 3 of 'msm_gem_get_iova_locked' from incompatible pointer type [-Werror]
msm_gem_get_iova_locked(fbdev->bo, 0, &paddr);
^
In file included from drivers/gpu/drm/msm/msm_fbdev.c:18:0:
drivers/gpu/drm/msm/msm_drv.h:153:5: note: expected 'uint32_t *' but argument is of type 'dma_addr_t *'
int msm_gem_get_iova_locked(struct drm_gem_object *obj, int id,
^
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dWKL
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding"
* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: control: Make sure that id->index does not overflow
ALSA: control: Handle numid overflow
ALSA: control: Don't access controls outside of protected regions
ALSA: control: Fix replacing user controls
ALSA: control: Protect user controls against concurrent access
drm/i915, HD-audio: Don't continue probing when nomodeset is given
ASoC: fsl: Fix build problem
ASoC: rsnd: fixup index of src/dst mod when capture
ASoC: fsl_spdif: Fix integer overflow when calculating divisors
ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
ASoC: sigmadsp: Split regmap and I2C support into separate modules
ASoC: MMP audio needs sram support
ASoC: pxa: add I2C dependencies as needed
This commit add check for return value of init_ring_common() in the
init_render_ring(). Now, when failure is detected the error code is
propagated to the caller instead of being ignored.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.
Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.
But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.
To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).
Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.
v2: Lots of improvements
Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
Suggested by Chris.
Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.
v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.
v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.
v5: Fixup locking around the fbcon set_to_gtt_domain call.
v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
object. We already have precedence for fb_obj in the pin_and_fence
functions.
v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
directly. These functions center on the plane, the actual object is
irrelevant - even a flip to the same object as already active should
cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
currently just calls intel_frontbuffer_flush since the implemenation
differs.
This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.
Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.
v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.
v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.
v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
still has work left to do before it's fully generic.
v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.
v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The downclocking checks a few more things, so not that simple to
convert. Also, this should get unified with the drrs handling and also
use the locking of that. Otoh the drrs locking is about as hapzardous
as no locking, at least on first sight.
For easier conversion ditch the upclocking on unload - we'll turn off
everything anyway.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should be taking the right power well refs these days, so this
shouldn't be necessary. It also gets in the way of re-using these
routines for S0iX states, as those need all the power saving features
enabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need to uninstall the full handler, simply disabling interrupts
ought to be enough.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
X could end up putting the fbcon fb into other domains, e.g.
for smooth take-overs. Also we want this for accurate frontbuffer
tracking: The set_config is an implicit flush and will re-enable
psr and similar features, so we need to bring the bo back into
the gtt domain.
v2: Add FIXME comment about fbcon locking fun in atomic context,
requested by Chris.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following list empty check is unnecessary because we would still do nothing
real and return 'val' if my_list is empty.
if (list_empty(&my_list))
return val;
list_for_each_entry(pos, &my_list, member) {
...
}
return val;
This patch removes the unnecessary check in drm_fb_helper_debug_enter().
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can be useful to figure out imbalances and bugs in the frontbuffer
tracking.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So from just a quick look we seem to have enough information to
accurately figure out whether a given gem bo is used as a frontbuffer
and where exactly: We have obj->pin_count as a first check with no
false negatives and only negligible false positives. And then we can
just walk the modeset objects and figure out where exactly a buffer is
used as scanout.
Except that we can't due to locking order: If we already hold
dev->struct_mutex we can't acquire any modeset locks, so could
potential chase freed pointers and other evil stuff.
So we need something else. For that introduce a new set of bits
obj->frontbuffer_bits to track where a buffer object is used. That we
can then chase without grabbing any modeset locks.
Of course the consumers of this (DRRS, PSR, FBC, ...) still need to be
able to do their magic both when called from modeset and from gem
code. But that can be easily achieved by adding locks for these
specific subsystems which always nest within either kms or gem
locking.
This patch just adds the relevant update code to all places.
Note that if we ever support multi-planar scanout targets then we need
one frontbuffer tracking bit per attachment point that we expose to
userspace.
v2:
- Fix more oopsen. Oops.
- WARN if we leak obj->frontbuffer_bits when freeing a gem buffer. Fix
the bugs this brought to light.
- s/update_frontbuffer_bits/update_fb_bits/. More consistent with the
fb tracking functions (fb for gem object, frontbuffer for raw bits).
And the function name was way too long.
v3: Size obj->frontbuffer_bits correctly so that all pipes fit in.
v4: Don't update fb bits in set_base on failure. Noticed by Chris.
v5: s/i915_gem_update_fb_bits/i915_gem_track_fb/ Also remove a few
local enum pipe variables which are now no longer needed to make the
function arguments no drop over the 80 char limit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
